Construction of Sub Tehsil Building at Alampur Distt. Kangra H.P.

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains etc. in all kind of soil (not exceeding 1.5 m (one point five Metre) in width or 10 Per Square Metre (ten square Metre) on plan), including dressing of sides and ramming of bottoms, lift upto any height, including getting out the excavated soil and disposal of surplus excavated soil asdirected, within a lead from the edge of excavation . All kind of soil complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Any loss to the private and public property during course of construction shall be absolute responsibility of the contractor. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Foundation, footings basis of columns etcetera and mass concrete including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etcetera upto any thickness including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Columns, Pillars, Piers, Abutments, Posts and Struts up to all width and heights including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Beams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depth and in all heights including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in wall any thickness including attached pilasters, butteresses, plinth and string courses and in all heights including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Edges of slabs and breaks in floors and walls up to all width and heights including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Stairs, (excluding landings) except spiral stair cases including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying in position cement concrete 1:5:10 (One cement: five sand: ten graded crushed/broken stone aggregate 40mm nominal size ) and curing complete, excluding cost of form work in foundation and plinth including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying in position cement concrete 1:4:8 (One cement: four sand: eight graded crushed/broken stone aggregate 40mm nominal size ) and curing complete, excluding cost of form work in foundation and plinth including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying in position cement concrete 1:3:6 (One cement: three sand:six graded crushed/broken stone aggregate 20mm nominal size ) and curing complete, excluding cost of form work in foundation and plinth including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and Laying damp-proof course 40mm (forty milimetre) thick with cement concrete 1:2:4 (one cement : two sand : four graded stone aggregate 12.5mm (twelve point five milimetre) nominal size) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and applying a coat of residual petroleum bitument of grade of VG-10 of approved quality using 1.7 Per Kilogram (one point seven kilogram). Per square metre on damp proof courase after cleaning the surface with brushes and finally with a piece of cloth lightly coaked in kerosene oil. including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying in position cement concrete of specified grade of reinforcement concrete excluding the cost of centering and shuttering finishig and reinforcement- All work up to plinth level : 1:1.½:3 (one cement : one and half coarse sand : three graded stone aggregate) 20 mm (twenty milimetre) nominal size in foundation footing bases of coulmn and the like including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° (Fifteen Degree) landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (One cement : one point five coarse sand : Three graded stone aggregate 20 mm (Twenty Millimetre) nominal size) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (One cement : one point five coarse sand : Three graded stone aggregate 20 mm (Twenty Millimetre) nominal size) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Smooth finishing of the exposed surfaces of RCC work with 6mm (six millimetre) thick cement mortar (1:3) one cement isto three sand including straigthening, cutting, bending, placing in position and binding all complete including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Steel reinforcement TATA TISCO/SAIL for reinforced cement concrete work including strengthening, cutting, bending, binding and placing in position complete and binding all complete avobe plinth level TMT bar grade Fe-500 including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Brick work with common burnt clay F.P.S. (Non Modular) bricks of class designation 7.50 in cement mortar 1:6 (one cement isto six sand) in foundation and plinth as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Brick work with common burnt clay F.P.S. (Non Modular) bricks of class designation 7.50 in cement mortar 1:6 (one cement isto six sand) in Super Structure as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Half Brick masonry with common burnt clay F.P.S. (Non Modular) bricks of class designation 7.50 in cement mortar 1:4 (one cement isto four sand) in Super Structure as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Supplying and stacking of hard stone (for stone pitching) as per site as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing cup board shutters 25 mm (twenty five millimeters)thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm (twenty five millimeters) wide x12 mm( twelve millimeters) thick with necessary screws and bright finished stainless steel piano hinges, as per site as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing prelaminated flat pressed three layers ( medium density) partical board or graded wood partical board IS: 3087 marked, with one side decorative and other side blancing lamination grade-I, Type0II exterior grade IS: 12823 marked of Action tesa, black cobra, green ply, kit ply make in shelves with screws and fittings wherever required, edges to be painted with polyurethene primer 18 mm( eighteen millimeters)thick as per site as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing prelaminated flat pressed three layers ( medium density) partical board or graded wood partical board IS: 3087 marked, with one side decorative and other side blancing lamination grade-I, Type0II exterior grade IS: 12823 marked of Action tesa, black cobra, green ply, kit ply make in shelves with screws and fittings wherever required, edges to be painted with polyurethene primer 25 mm( twenty five millimeters)thick as per site as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 12 mm (twelve millimeters) thick commercial ply confirming to IS:1328 BWR type of action tesa, Black cobra, green ply make plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face and fixed on wooden/steel frame work complete as per site as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing decorative high pressure laminated sheet of plain/ wooden grains in gloss/matt/suede finish with high density protective surface layer and reserve side of adhesive bonding quiality confirming to IS:2046 type S including cost of adhesive of approved quality 1.00 mm ( one millimeters) thick as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm( eighteen into five millimeters) fixed with wooden adhesive of approved quality and screws/nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge. as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing panelling with ply wood 7 ply, 9 ply ( seven ply, nine ply) thick action tesa, black cobra, green ply, kit ply, decorative plywood one side decorative veneer and commercial beneer on other face ( type-I ) confirming to IS 1328 BWR type as per direction of Engineer-in-charge. as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing wood work in frames of false ceiling, partitions extra sawn and fixed in position with necessary stainless steel screws extra Sal wood as per direction of Engineer-in-charge. as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing wood wooden moulding corner beading if triangular shape to the junction of panelling extra with iron screws, plugs and priming coat on unexposed surface complete 2nd class teak wood 55x30 mm ( fifty five into thirty) millemeters as per direction of Engineer-in-charge. as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing wood wooden moulding corner beading if triangular shape to the junction of panelling extra with iron screws, plugs and priming coat on unexposed surface complete 2nd class teak wood 25x12 mm ( twenty five into twelve) millemeters as per direction of Engineer-in-charge. as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing wood wooden moulding corner beading if triangular shape to the junction of panelling extra with iron screws, plugs and priming coat on unexposed surface complete 2nd class teak wood 19x19 mm ( ninteen into ninteen) millemeters as per direction of Engineer-in-charge. as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing power coated coloured aluminium of Jindal/Hindaclo or equavalent work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings as per direction of Engineer-in-charge. as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

for fixed portion polyester coloured powder coated aluminum coating 50( fifty ) mircon as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing power coated coloured glazing in aluminum door, windows shutter and partation extra with EPDM rubber/ neoprene gasket extra complete with flat glass panes of 5mm ( five millimeters) thick weight not less than 12.50 kg ( twelve point five kilograme)/sqm as per architectural drawing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing power coated coloured glazing in aluminum door, windows shutter and partation extra with EPDM rubber/ neoprene gasket extra complete with flat glass panes of 4mm ( four millimeters) thick weight not less than 10.00 kg ( ten kilograme)/sqm as per architectural drawing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg( one hundred twenty five kilograms), for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. as per architectural drawing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing fly proof stainless steel grade 304 wire gauge with 0.05 mm ( zero point five millimeters) wire and 1.40 mm ( one point four millimeters) wide aperture with matching as per architectural drawing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm( two hundred millimeters) centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. (Only weight of grill to be measured for payment). as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 12 mm( twelve millimeters) thick prelaminated particle board with decorative lamination on both sidesflat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 12 mm( twelve millimeters) thick prelaminated particle board with decorative lamination on one side and balancing lamination on other sideflat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing machine moulded aluminium covering of approved pattern & design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm (eight millimeters) dia and 75 mm ( seventy five millimeters) long bolt including providing aluminium washers 2 mm( two millimeters) thick & 15 mm ( fifteen millimeters) dia , at a staggered pitch of 200mm(two hundred millimeters) centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. Powder coated aluminium sheet 2.5mm( two point five millimeters) thick (minimum thickness of powder coating 50 ( fifty) micron) complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing aluminum sliding door bolts, ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete (a) :300x16 mm (three hundred into sixteen millimetre) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing aluminum sliding door bolts, ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete (b):250x16 mm (Two hundred fifty into sixteen millimetre) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing aluminum tower bolts, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete (a) :200x10 mm (Two hundred into ten millimetre) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. T

Providing and fixing aluminum tower bolts, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete (b):150x10 mm (One hundred fifty into ten millimetre) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing aluminum tower bolts, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :1000x10 mm (One hundred into ten millimetre) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing aluminum handles, 125 mm ( one hundred twenty five millimeters )ISI marked,anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing aluminum handles, 100 mm ( one hundred millimeters )ISI marked,anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing aluminum handles, 75mm ( seventy five millimeters )ISI marked,anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing chromium plated brass 50 mm ( fifty millimeters ) cupboard or wardrobe knob with nuts complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing special quality bright finished brass cup board or ward robe locks with four livers of approved quality including necessary screws extra complete 40 mm ( forty millimeters) and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 150 mm ( one hundred fifty millimeters) bright finished floor brass door stopper with rubber cushion including necessary screws extra complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing bright finished brass hard drawn hooks and eyes 150 mm ( one hundred fifty millimeters) and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm( one point five millimeters) with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete :as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing triple strip verticla type magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.:as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Kota stone slab flooring over 20 mm( twenty millimeters) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four coarse sand) :as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Marble stone flooring with 18 mm ( eighteen millimeters)thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (one cement : four coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Kota stone slabs 20 mm (twenty millimeters) thick in risers of steps, skirting, dado and pillars laid on 12 mm (twelve millimetrs)(average) thick cement mortar 1:3 (one cement: three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.:as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying Polished Granite stone flooring with cherry red elite brown cat eye or equavalent in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm(eighteen millimeters) thick stone slab over 20 mm (twenty millimeters)(average) thick base of cement mortar 1:4 (one cement : four coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying Polished Granite stone flooring with cherry red elite brown cat eye or equavalent in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm(eighteen millimeters) thick stone slab over 20 mm (twenty millimeters)(average) thick base of cement mortar 1:4 (one cement : four coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete for pre finished nosing to treads of steps of marbel stone as specified and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing full body matt finish/ double charge vetrified floor tiles in different sizes with water absorption less than 0.08% and confirming to IS:15622 of approved make in all colours and shades laid in 20 mm ( twenty millimeters) thick cement mortor 1:4( one cement: four sand) jointing with grey cement and matching pigment etc.complete size of tile 600x600 mm ( six hundred into six hundred millimeters) of / Nitco/Rak/ Kazaria/Orient /Somany as specified and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing full body matt finish/ double charge vetrified tiles of size 300x300x9.8 mm ( three hundred into three hundred into nine point eight millimeters) having water absorption less than 0.5% and confirming to IS:15622 of approved make in all colours and shades laid in 20 mm ( twenty millimeters) thick cement mortor 1:4( one cement: four sand) jointing with grey cement and matching pigment etc.complete of / Nitco/Rak/ Kazaria/Orient /Somany as specified and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm( three hundred into three hundred millimeters) or more of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. of / Nitco/Rak/ Kazaria/Orient /Somany as specified and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying Vitrified tiles in different sizeswith water absorption less than 0.08 %( zero point eight percent) and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm (twelve millimeters) thick bed of cement mortar 1:3 (one cement: three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete size of tile 600x600 mm ( six hundred into six hundred millimeters) of / Nitco/Rak/ Kazaria/Orient /Somany as specified and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm (twelve millimeters)thick bed of cement Mortar 1:3 (one cement: three coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing inwhite cement mixed with pigment of matching shade complete. and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Grouting the joints of flooring tiles having joints of 3 mm (three millimeters)width, using epoxy grout mix of 0.70 kg( zero point seven zero kilograme ) of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete (300x300 mm) ( three hundred into three hundred millimeters) and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Grouting the joints of flooring tiles having joints of 3 mm (three millimeters)width, using epoxy grout mix of 0.70 kg( zero point seven zero kilograme ) of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete (600x600 mm) ( six hundred into six hundred millimeters) and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm (twenty into twent into four millimeters) in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg ( two point five kilograme) per sqm and grouting of the same. and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Chequerred precast cement concrete tiles 22 mm ( twenty two millimeters) thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm ( twenty millimeters) thick bed of cement mortar 1:4 (one cement: four coarse sand) Light shade pigment using white cement . and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm( fifty millimeters) thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

60mm( sixty millimeters) thick cement concrete paver block of M-35 grade with approved colour, design & pattern of NTC make.

80 mm( eighty millimeters) thick cement concrete paver block of M-35 grade with approved colour, design & pattern of NTC make.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm ( zero point five zero millimeters)(+ 0.05 %) total coated thickness with zinc coating 120 ( one hundred twenty )grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 ( five to seven)microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm)( five point five into fifty five) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm ( zero point five zero millimeters) (+0.05 %) total coatedthickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 ( fifteen to eighteen) microns using self drilling/ self tapping screws complete ridges 500-600 mm ( five hundred to sis hundred millimeters) and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm ( zero point five zero millimeters) (+0.05 %) total coatedthickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 ( fifteen to eighteen) microns using self drilling/ self tapping screws complete Crimp curve. and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm ( zero point five zero millimeters) (+0.05 %) total coatedthickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 ( fifteen to eighteen) microns using self drilling/ self tapping screws complete flashing/ aprons upto 600 mm ( six hundred millimeters). as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing unplasticised -PVC pipe 110 mm dia ( one hundred ten millimeters) clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm ( fifty into fifty into fifty millimeters) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etc. complete. as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm ( ten millimeters) gap for thermal expansion, (i) Single socketed pipes. 110 mm dia of D-plast or vectus make as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm ( ten millimeters) gap for thermal expansion.as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Plain bend 110 mm ( One hundred ten millimeters) Dia

Plain shoe110 mm ( One hundred ten millimeters) Dia

Coupler110 mm ( One hundred ten millimeters) Dia

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete in trusses and trussed purlins in building and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete ingrating, frames, guard bar ladder, railing, brackets, gates and siilar work complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 6 mm ( six millimeters) thick cement Evrest fiber board as per IS 14862 plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 1 mm( one millimeter) thick M.S. sheet sliding shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm ( three millimeter)M.S. gusset plates at the junctions and corners, 25 mm( twenty five millimeters) dia pulley, 40x40x6 mm ( forty into forty into six millimeters)angle and T iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Applying priming coat: with ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr. (zero point nine zero liter /10 (ten) Per Square Metre. Over an under coat of primer applied @ 0.75 ltr (zero point seven five)/ 10 (ten) Per Square Metre. of approved brand and manufacture including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Polishing on wood work with ready made wax polish of approved brand and manufacture and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

6 mm (six milimetre) cement plaster of mix: 1:3 (one cement : three fine sand) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

12 mm (twelve millimetre) cement plaster in single coat on fair side of brick/ stone masonry for interior plastering upto floor two level with CM 1:6 (One cement :six sand) carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

20mm (Twenty millimetre) cement plaster in single coat on rough side of brick/ stone masonry for interior plastering upto floor two level with CM 1:6 (One cement : Six sand) carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and Applying white cement Birla white based putty of average thickness 1 mm ( one millimeters) of approved brand and manufacture over plaster surface even and smooth complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade.and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Two or more coats applied on walls @ 1.25 ltr (one point two five liter ) /10 (ten) Per Square Metre over and including one coat of Special primer applied @ 0.75 ltr (zero point seven five liter ) /10 (ten) Per Square Metre including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Distempering with oil bound washable distemper of approved brand and manufacture to give aneven shade: New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50( fifty ) grams/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67( one point sixty seven)liter/10 ( ten)suqare meter over and including priming coat of exterior primer applied @ 2.20 ( two point twenty )kg/10 sqm)and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 23 cm (twenty three centimeters) dia half round ( to level and slopes) and joining with stiff misture of cement mortor in the proporation of 1:1 ( one cement : one sand) salt glazed stone ware pipes grade "A" of the following internal diameters including testing of pipes and joints complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 (one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement isto one point five coarse sand (zone- III) : three graded stone aggregate 20 mm(twenty millimeters) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm ( forty millimeters )nominal size), inside plastering 12 mm ( twelve millimeters)thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm(twenty millimeters) nominal size) finished with a floating coat of neat cement complete as per standard design in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Inside size 90x80 cm(Ninety into eighty centimeter) and 45 cm( forty five centimeters) deep including C.I. cover with frame (light duty) 455x610 mm(four hundred fifty five into six hundred ten millimeters) internal dimensions, total weight of cover and frame to be not less than 38 kg( thirty eight kilograme (weight of cover 23 kg(twenty three kilograme) and weight of frame 15 kg)(fifteen kilograme)With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven point five) in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Inside size 120x90 cm(one hundred twenty into ninety centimeter) and 90 cm( ninety centimeters) deep including C.I. cover with frame (light duty) 500 mm ( five hundred millimeters) internal dimensions, total weight of cover and frame to be not less than 116 kg( one hundred sixteen kilograme) (weight of cover 58 kg(fifty eight kilograme) and weight of frame 58 kg)(fifty eight kilograme)With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven point five) in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing Polyethelene-aluminum Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge. 1216 ( 16mm (sixteen millimetre) Outer Dia Pipe) Concealed work, including cutting chases and making good the wall etc. including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

16 mm ( sixteen millimeters) nominal size 1216

20 mm ( twenty millimeters) nominal size 1620

Providing and laying cement concrete 1:5:10 (one cement : five coarse sand : ten graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 600x450mm (six hundred into four hundred fifty millimetre) light duty rectangular C.I. manhole with frame cover weight 50 Per Kilogram (fifty kilogram) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, 500 (five hundred ) liter IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m( one point five meter), including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm( twenty centimeters) in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m( fifty meters) as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing brass full way valve with steel wheel 15 mm ( fifteen millimeters) nominal size of Zindal/Tata make in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 (ten) litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm ( forty millimeters) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid eureopean pan EWC of star no 20087 of Cera/Hindware/Jaguar including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing wash basin with C.I. brackets, 15 mm ( fifteen millimeters) dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required completewash basin size 550x400 mm( five hundred fifty into four hundred) of delta no 10010 in all respect as per directions of Engineer-in-Charge.including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal star white/snow white shade of Cera / Hindware/jaquar for wash basin completely recessed at the back for then reception of pipes and fittings including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge..The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 32 mm (thirty two millimetre) dia P.V.C. waste pipe of Supreme/finolex/prince for sink or wash basin including P.V.C. waste fittings complete including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 600x450 mm (six hundred into four hundred fifty millimetre) beveled edge mirror superior glass of Atul/Modi Gaurd (of approved quality) complete with 6 mm (six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing PTMT towel rail of Jal/Jaquar/ ESS ESS / cera/ hindware complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm (six hundred millimetre) long towel rail with total length of 645 mm (six hundred forty five millimetre) , width 78 mm (seventy eight millimetre) and effective height of 88 mm (eighty eight millimetre), weighing not less than 190 gms (one hundred ninety grams) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge .The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 600x120x5 mm (six hundred into one hundred twenty into five millimetre) glass shelf with edges round off, supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm (forty millimetre) long screws, rawl plugs etc.,complete including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. .The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government

Providing and fixing CP soap dish holder having length of 138 mm ( one hundred thirty eight millimeter) breadth 102 mm ( one hundred two millimeter) height 75 mm ( seventy five millimeters) chromium plated brass soap dish of of hindware/cera/Jal / Jaquar/ ESS ESS or contra with C.P. brass brackets fixed to wooden cleats with C.P. brass screws including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimetre) diameters C.P. brass bib tap of Jal/Cera/Hindware/Jaquar or contra with capstan head including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimetre) C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms( eight hundred ten grams) of continental series, Jal, Jaguar, Hindware make or its equavalent. including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing brass stop cock concealed (Heavy duty makes ISI marked is No. 8931) of Jal/Cera/Hindware/Jaquar approved quality 15mm (fifteen millimetre) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing uplasticised PVC connection pipe with brass union 45 cm ( forty five centimeter)length 15 mm ( fifteen millimeters) nominal bore Cera/ Jaguar finolex or hindware make including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing brass full way valve with steel wheel 20 mm ( twenty millimeters) nominal size of Zindal/Tata make in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing furrule including boring and taping the main 15 mm ( fifteen millimeters) nominal size of Zindal/Tata make in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Making connection of galvanised steel distribution brances with galvanised mild steel main 20 mm ( twenty millimeter) to 40 mm ( forty millimeters) nominal bore by providing and fixing tee including cutting and threading the pipes complete in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm ( three hundred into three hundred millimeters)size (inside) the weight of cover to be not less than 4.50 kg( four point five kilograme) and frame to be not less than 2.70 kg( two point seven zero kilograme) as per standard design 100x100 mm ( one hundred into one hundred millimeters)size P type With common burnt clay F.P.S. (non modular) bricks of class designation and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing G.I. Pipes complete with G.I. Fittings and clamps, i/c making good the walls etc. Concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall Zindal/Tata make and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

15 mm ( fifteen millimeters) nominal size

20 mm ( twenty millimeters) nominal size

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm ( five hundred eighty into three hundred eighty into three hundred fifty millimeters) with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing C.P. brass toilet paper holder as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing C.P. brass single layer telephonic wall mixer of quality and make as approve by Engineer-in Charge 15 mm (fifteen millimeters) diamenter as per direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 8 mm( eight millimeters) dia C.P. / S.S. Jet with flexible tube upto 1 ( one) metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.and as per direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing soil, waste and ventilating pipes 75 mm ( seventy five millimeters) dia centrifugally cast spun iron sockets and spigot (S & S) pipe as per IS 3989 and as per direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing soil, waste and ventilating pipes 100 mm ( one hundred millimeters) dia centrifugally cast spun iron sockets and spigot (S & S) pipe as per IS 3989 and as per direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing PVC floor trap self cleaning design with screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the wall and floor etc.hubless centrifugally cast spun epoxy coated inside and outside as per IS 16905 100 mm( one hundred millimeters) inlet and 75 mm ( seventy five millimeters)outlet as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing bend of required degree with acess door, insertion rubber washer 3 mm( three millimeters) thick bolts and nuts complete as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Hubless centrifugally cast spun epoxy coated inside and outside as per IS 15905 and 75 mm ( seventy five millimeters)

Hubless centrifugally cast spun epoxy coated inside and outside as per IS 15905 and 100 mm ( one hundred millimeters)

Providing and fixing single equal plain junction of required degree with access door ,insertion rubber washer 3 mm( three millimeters) thick bolts and nuts complete sand cast iron S & S as per IS:3989 as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

100x100x100 mm ( One hundred into One hundred into one hundred millimeters)nominal size

75x75x75 mm ( Seventy five into seventy five into seventy five millimeters) nominal size

Providing and fixing single plain bend of required degree hubless centrifugally cast iron spun iron pipes epoxy coated inside and outside IS:15905 as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

110 mm ( one hundred ten millimeters) nominal size

75 mm ( Seventy five millimeters) nominal size

Providing and fixing coller sand cast iron S and S as per -3989 as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

110 mm ( one hundred ten millimeters) nominal size

75 mm ( Seventy five millimeters) nominal size

Providing and fixing double equal junction of required degree with access door , insertion rubber washer 3 mm( three millimeters) thick bolts and nuts complete as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

100x100x100 mm ( One hundred into One hundred into one hundred millimeters)nominal sand cast iron S & S as per IS:3989

75x75x75 mm ( Seventy five into seventy five into seventy five millimeters) nominal size sand cast iron S & S as per IS:3989

Providing and fixing double equal plain junction of required degree as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

100x100x100 mm ( One hundred into One hundred into one hundred millimeters)nominal size sand cast iron S & S as per IS:3989

75x75x75 mm ( Seventy five into seventy five into seventy five millimeters) nominal size sand cast iron S & S as per IS:3989

Providing and fixing single equal plain junction of required degree as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

100x100x100 mm ( One hundred into One hundred into one hundred millimeters)nominal size sand cast iron S & S as per IS:3989

75x75x75 mm ( Seventy five into seventy five into seventy five millimeters) nominal size sand cast iron S & S as per IS:3989

Providing and fixing sand cast iron S & S off sets as per IS: 3989 and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

110 mm ( one hundred ten millimeters) nominal size

75 mm ( Seventy five millimeters) nominal size

Providing and fixing MS stay clamps for sand cast iron/centrifugally cast spun iron pipes of diameters and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

110 mm ( one hundred ten millimeters) nominal size

75 mm ( Seventy five millimeters) nominal size

Providing and fixing lead caulked joints to sand cast iron/centrifugally cast spun iron pipes of diameters and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

110 mm ( one hundred ten millimeters) nominal size

75 mm ( Seventy five millimeters) nominal size

Brick work with common burnt clay F.P.S. (Non Modular) bricks of class designation 7.50 in cement mortar 1:6 (one cement isto six sand) in foundation and plinth as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Half brick work with common burnt clay F.P.S. (Non Modular) bricks of class designation 7.50 in cement mortar 1:4 (one cement isto four sand) in foundation and plinth as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) complete as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing M.S. foot rests including fixing in main hole with 20x20x10 cm ( twenty into twenty into ten millimeters) cement concrete block 1:3:6 ( onecement: three coarse sand: six graded stoen agregate ) 20 mm ( twenty millimeters)nominal size as per standred design with 20x20 mm ( twenty into twenty millimeters) square bar and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing plain bend of required degree. Sand cast iron S&S as per IS - 1729 complete as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 3.00 H.P. ( three horse power ) Tollu pump complete making including board and fitting complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm (Twenty millimetre) nominal size) upto plinth level with :Cement mortar 1:6 ( one cement : Six coarse sand) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

15 mm (fifteen millimetre) cement plaster in single coat on rough side of brick/ stone masonry for interior plastering upto floor two level with CM 1:6 (One cement : six sand) carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10( One cement: five sand: ten graded stone aggregate )40 mm ( forty millimeters) nominal size in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

KARNAIL SINGH GOVT CONTRACTOR