PROVN OF JCOS OR LIVING AT 231 FD WKSH COY EME BATHROOM AND KITCHEN IN 15 SIKH LI AT HASIMARA MIL STN UNDER GE(S) BINNAGURI

Amount

M&L for surface dressing n exc 15 cm deep for adjoining area, complete all as specified and as directed by Engineer-in-charge.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft /loose, complete all as specified and as directed by Engineer-in-charge.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft/loose soil, complete all as specified and as directed by Engineer-in-charge.

Returning filling in, incl spreading, levelling watering & well ramming in layers n.exc 25cm in soft/loose soil, complete all as specified and as directed by Engineer-in-charge.

Removing excavated material exc. 500 m but n exc. 1500 m and depositing where directed at a stabilised level, complete all as specified and as directed by Engineer-in-charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and as directed by Engineer-in-charge.

M&L for Moorum/red bajri filling in floors or paving's, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering, complete all as specified and as directed by Engineer-in-charge.

M&L for Broken stone Broken or boulders for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and as directed by Engineer-in-charge.

M&L for anti termite treatment of soil along with external perimeter of building @ 2.25 L of emulsion per meter of the perimeter of wall, complete all as specified and as directed by Engineer-in-charge.

M&L for anti termite treatment of soil of top surface filled earth of building @ 5.0 L of emulsion per sq meter of surface area, complete all as specified and as directed by Engineer-in-charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface, complete all as specified and as directed by Engineer-in-charge.

M&L for Cement concrete Type B1 1:2:4 (20 mm graded aggregate) as in bed plates, kerbs , water troughs and the like including weathering, slightly rounded for chamfered angles and throating,, complete all as specified and as directed by Engineer-in-charge.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete, complete all as specified and as directed by Engineer-in-charge.

M&L for cement concrete 1:3:6 type C-2, using 40mm graded stone aggregates as in foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-charge.

M & L for PCC (1:2:4) type B1 (using 20 mm graded stone aggregate), cast in situ, in benching, coping and the like etc including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified and as directed by Engineer-in-charge.

M&L for precast reinforced cement concrete (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in cover slab in drain/manhole set in cement mortar (1:4) complete all as specified and directed. (NOTE: Cost of form work is deemed to be inclusive of unit rate quoted by the contractor & reinforcement shall be measured & paid separately.)

M&L for RCC (Design mix) M-25 grade using 20mm graded stone aggr as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed

M&L for RCC (Design mix) M-25 grade using 20mm graded stone aggr as in Columns, pillars, piers, posts and struts, complete all as specified and as directed by Engineer-in-charge.

M&L for RCC (Design mix) M-25 grade (using 12.5 mm graded stone aggregate) in Beams, cantilevers, lintels over 1.5 M span, complete all as specified and as directed by Engineer-in-charge.

M&L for RCC (Design mix) M-25 grade (using 12.5 mm graded stone aggregate) in chajjas, complete all as specified and as directed by Engineer-in-charge.

M&L for fly ash Brick work using modular size bricks with sub class 'B' bricks curved on plan with mean radius not exc 6m with bricks roughly cut to radius or bricks with wedge shaped joints built in cement mortar 1:6, complete all as specified and as directed by Engineer-in-charge.

M&L for fly ash brick work with modular bricks, straight or curved on plan exc. 6m mean radius in cement mortar 1:4, complete all as specified and as directed by Engineer-in-charge.

M&L for Brickwork with flash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4, complete all as specified and as directed by Engineer-in-charge.

M&L for 40mm thick Damp proof course to horizontal or vertical surfaces including necessary formwork in PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate, complete all as specified and as directed by Engineer-in-charge.

M&L for applying evenly a coat of blown type bitumen @1.50 kg / Sqm and blinding with clean dry sand @ 0.05 Cum/ Sqm, complete all as specified and as directed by Engineer-in-charge.

Supply and laying of Polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg /Sqm, complete all as specified and as directed by Engineer-in-charge.

Providing form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves, for flat rough finished concrete surfaces, complete all as specified and as directed by Engineer-in-charge.

Providing formwork to Formwork to sides of pillars, posts, struts, piers, columns, and stanchions for rough finished surfaces of concrete, complete all as specified and as directed by Engineer-in-charge.

Providing formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished flat surface of concrete, complete all as specified and as directed by Engineer-in-charge.

Providing form work to chullah hood, chajjas, troughs and similar items including edges etc for rough finished flat concrete surface, complete all as specified and as directed by Engineer-in-charge.

S&F of factory made solid PVC door frame of size 50mm X 47mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube as per specification and drawing as mentioned in SSR Part-II (2020), Section 8, complete all as specified and as directed by Engineer-in-charge.

S&F of Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 4mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification with Wood free EPS, complete all as specified and as directed by Engineer-in-charge.

S&F of 150 mm long Aluminium anodised barrel tower bolts, complete all as specified and as directed by Engineer-in-charge.

S&F of aluminium handles 125 mm size cast type anodised, complete all as specified and as directed by Engineer-in-charge.

S&F of Butt hinges, medium weight, cold rolled mild steel 75 mm long, complete all as specified and as directed by Engineer-in-charge.

S&F of pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 125 x60 mm, complete all as specified and as directed by Engineer-in-charge.

M&L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required, complete all as specified and as directed by Engineer-in-charge.

S&F of 30mm flush shutter, solid core construction, with block board core and plywood face panel, commercial type on both side etc, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing of factory made partly glazed three panels i.e. upper panel will be wire mesh and further divided into two panels fitted externally in the clear space & lower panel will be plain colour PVC sheet 5mm thick PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as per specified and as directed by Engineer-in-charge.

S&F of stainless steel wire cloth 0.36 nominal dia wire & average width of aperture 1.40 mm fixed with stainless steel wire staples complete all as specified and directed

S&F of 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and as directed by Engineer-in-charge.

S&F of 100 mm butt hinges of mild ,medium weigh steel, complete all as specified and as directed by Engineer-in-charge.

S&F of Aluminium anodised barrel tower bolts of extruded section 200 mm long all as Specified and directed by Engr-in Charge.

S&F of Aluminium handles 150mm size cast type anodised complete all as specified and as directed by Engineer-in-charge.

M&L for 75 mm Hasp and Staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge pin including bolt to hinge plate and fixed with bolt screw, complete all as specified and as directed by Engineer-in-charge.

S&F of 75 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and as directed by Engineer-in-charge.

S&F of Aluminium anodised , Sliding door bolt of 300mm long , fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by Engineer-in-charge.

S&F of Powder coated aluminium window sliding type three track (2 glazed & one gauze shutter ) aluminium sections weighing not less than 1.67kg/m for frame and 0.55 kg/m for shutter including necessary jointing cleats, glazing cleats, rubber packing , screws, handle, locking arrangement and 4 mm thick plain/tinted glass and aluminium mosquito proof gauge including making good disturbed surface of wall, complete all as specified and as directed by Engineer-in-charge.

S&F of Powder coated aluminium louvered ventilators of size n exc 0.50 Sqm area with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazing cleats, rubber packing , anodised aluminium snap beading, screws, anodised aluminium fittings and 5.5mm thick tinted glass fixed in panels with suitable locking arrangements including making good disturbed surface of wall, complete all as specified and as directed by Engineer-in-charge.

M&L for providing & fixing factory made solid PVC cup board frame of size 50 mm x 47 mm with a wall thickness of 5 mm made out of extruded 5 mm thick prelam/plain colour PVC sheet reinforced with 19 mm x 19 mm MS square tube of 19 gauge thickness throughout the frame and metre cut at two corners and jointed with 2 Nos of 150 mm long brackets of 150 mm long brackets of 15 mm x 15 mm MS Square tubes. The door frame shall be fixed to the wall using 100 mm long MS screws through the frame by using PVC fasteners. A minimum 4 Nos of screws to be provided for each vertical membered minimum 2 Nos of screws to be provided to the horizontal member etc., complete all as specified and as directed by Engineer-in-charge.

M&L for providing & fixing factory made solid PVC cup board shutter (Flush type) of 20 mm thick made from co- extruded 3 layer rigid PVC foam sheet (single extruded) with density not less than 600kg/cum outer layer (0.8-1mm) thick should be of rigid PVC with density of not less than 1400kg/cum manufactured by an ISO 9001-2015 certified company. Door should be water proof, termite proof, fire retardant and having good screw holding capacity, with all sliding and locking arrangement, complete all as specified and as directed by Engineer-in-charge.

M&L for Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed by Engineer-in-charge.

M&L for TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips, complete all as specified and as directed by Engineer-in-charge.

M&L for Mild Steel TMT bar 5mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed by Engineer-in-charge.

S&F of Structural steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe 410-W (Gde -E-250 quality- A) Add to any of the foregoing items if structural steel is painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication complete all as specified and directed.

M&L for providing and fixing factory made PVC shelf/partition of required size consisting of 18 mm thick solid PVC sandwich with 1 mm thick plain PVC sheet on both sides suitable fixed in, complete all as specified and as directed by Engineer-in-charge.

S&F of MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-410-W (Gde E-250 quality B) with riveted, bolted or welded attachment complete all as specified and as directed by Engineer-in-charge.

S&F of Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment steel of Fe 410-W (Gde E250) quality-B complete all as specified and as directed by Engineer-in-charge.

S&F of Stainless steel bolts. Of neck dia exc 20mm and n.exc 25mm purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30cm long complete all as specified and as directed by Engineer-in-charge.

M&L Steel work in tubular trusses, purlins, post including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 painted one shop coat of red oxide primer complete all as specified and directed by Engineer-in-charge.

S&F of Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hook sand hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete. Fe 410 -W (Gde- E- 250)quality complete all as specified and os directed by Engineer-in-charge.

S&F of Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, et, .Fe 410 -W (Gde- E- 250)quality complete all as specified and as directed by Engineer-in-charge.

S&F of mild steel framed work such as grills, grating etc with ends of bars shouldered and /or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, frame work of water tanks and similar work conforming to FE-290 Gde E-165, complete all as specified and as directed by Engineer-in-charge.

S&F of stainless steel curtain rods 20-25 mm dia, anodised aluminium alloy with fixing brackets , stops complete all as specified and as directed by Engineer-in-charge.

S&F of pre painted galvalume aluminium zinc coating AZ 150 GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/ cladding/ eaves board fixed with selp tapping screw, complete all as specified and as directed by Engineer-in-charge.

S & F of pre painted galvalume aluminium zinc coating AZ 150 GI based plain steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding/eaves board fixed with selp tapping screw, complete all as specified and as directed by Engineer-in-charge.

S&F of Anodised aluminium snap grid size 605mm x 605mm frame work for false ceiling all as specified and as directed by Engineer-in-charge

M&L for non Asbestos ,fibre reinforced standard cement board as in ceiling ,4mm thick designer board (610mm x 610mm ) complete all as specified and as directed

M&L for 75mm thick PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in plinth protection & floor including finishing the cement concrete surface even and smooth without using extra cement, complete all as specified and as directed by Engineer-in-charge.

M&L for providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour , design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc of required strength , thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using palate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and as directed by Engineer-in-charge.

M&L for 100mm thick PCC type C-2, (1:3:6) using 40mm graded stone aggregate as in sub base of floor, hard standing, path, complete all as specified and as directed by Engineer-in-charge.

Providing and fixing factory made uPVC white colour sliding window Three track made of extruded profile with wall thickness of 2.3 mm (+ -0.2mm).Window profile with hollow section with multi chamber. Frame (88mm x 52mm).Sliding mesh Sash (42mm x 57mm),sliding interlock (one vertical length in each shutter) (45.5mm x 28mm),Glazing bed (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc, making arrangement for fixing of hardware. EPDM gasket,1.2+ - 0.2mm thick galvanised steel frame (30mm x 18mm) 2 Nos, sliding sash (30mm x 18 mm),sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with (8mm x 100mm) long fasteners, hardware touch lock zinc alloyed (white powder coated),steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and required accessories. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories.Net opening will be measured for payment purpose. Area not exceeding 2.00 Sqm each, complete all as specified and as directed by Engineer-in-charge.

M&L for 50 mm thick PCC 1:2:4 Type B1 (using 20mm graded granite stone aggregates) as in floor, complete all as specified and as directed by Engineer-in-charge.

M&L for 20 mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm & 10mm) mixed with water proofing compound in top layer @ 200 ml per beg of cement and finishing the surface fair and even without using extra cement, complete all as specified and as directed by Engineer-in-charge. (Note: Water proofing compound shall be measured and paid separately under relevant item of schedule 'A').

M&L for 20 mm thick plaster of cement mortar (1:4) rendering on other than fair faces of brick work and finishing the surface fair and even without using extra cement complete all as specified and as directed by Engineer-in-charge.

Supply only Liquid water proofing compound all as specified and directed by Engineer-in-charge.

M/L for rendering 15mm thick in CM 1:4 on Brick / stone masonry surfaces finishing even and smooth without using extra cement, complete all as specified and as directed by Engineer-in-charge.

M&L for 15mm thick rendering in cement mortar 1:6 on other than fair face of brick work or concrete surface finished fair and even (without using extra cement), complete all as specified and as directed by Engineer-in-charge.

M&L for coloured Non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floor etc set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed in whiter or coloured cement to match as in floor, complete all as specified and as directed by Engineer-in-charge.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18Sqm but n. exc. 0.38 Sqm, vertical surfaces, in skirting etc. set and jointed in neat cement slurry and pointed in whiter or coloured cement to match as in floor, complete all as specified and as directed by Engineer-in-charge.

M&L for 10mm thick rendering in CM (1:4) as backing layer in vertical surfaces of skirting dados repairs to steps, complete all as specified and as directed by Engineer-in-charge.

M&L for glazed coloured ceramic tiles (450x350x7mm thick) on vertical surfaces such as skirting/dado set and jointed in neat cement slurry pointed in white or coloured cement to match over 15mm thick rendering in CM(1:4) all as specified and directed by Engineer-in-charge.

M&L for 20 mm thick granite (of any type)work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed by Engineer-in-charge.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate, 75mm thick in plinth protection and footpath laid in panels and finished even and smooth without using extra cement including necessary form work, complete all as specified and as directed by Engineer-in-charge. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection, complete all as specified and as directed by Engineer-in-charge.

Materials and labour for 150 mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in sub-base of floor over, complete all as specified and as directed by Engineer-in-charge.

M&L for 25 mm thick PCC (1:2:4) type B1 ( 20mm graded stone aggregate) , finished concrete surfaces even and rough to receive floor finishes, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over wall case putty 1 mm thick to wall surface, complete all as specified and as directed by Engineer-in-charge.

M&L for Preparing new plastered surfaces and applying two coat of cement base paint on surfaces of walls complete all as specified and as directed by Engineer-in-charge.

M&L for preparing new Plastered surfaces of walls and finishing the walls with Acrylic smooth exterior paint of required shade : New work (Two or more coats applied @1.67 Ltr/10 Sqm over and including priming coat of exterior primer applied @ 2.20 Kg/ 10 sqm), complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as Specified.

M&L for two coat of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth incl preparation of surfaces, complete all as specified and as directed by Engineer-in-charge.

S&F of vitreous China wash basin, white, flat back, size 550x400m excluding taps, waste , including chain & plug & porcelain stopper ,brackets, cutting for pinning in ends of brackets or erecting stand and fixing and supply and waste pipe complete all as specified and as directed by Engineer-in-charge.

S&F of 15 mm fancy type swan neck pillar taps, cast copper alloy with capstone heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore, complete all as specified and as directed by Engineer-in-charge.

S&F of CP toilet paper holder with flat recessed type stainless steel, complete all as specified and as directed by Engineer-in-charge.

S&F of 10 ltr capacity dual type PVC flushing cistern low level white colour incl PVC connection PVC flush pipe of reqd length, complete all as specified and as directed by Engineer-in-charge.

S&F of vitreous China wash down water closet pan (pedestal pattern), white including connection trap and to flushing pipe, anti-siphonage pipe etc complete including, complete all as specified and as directed by Engineer-in-charge.

S&F of PVC seat cover for pedestal pan, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminumized hanging device complete all as specified and as directed by Engineer-in-charge.

S&F of Bib taps long body fancy type cast copper alloy, chromium plated for 15mm bore pipe, screwed for iron pipes or of brass complete all as specified and as directed by Engineer-in-charge.

S&F of stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type) for 15mm bore pipe, screwed both ends including necessary fittings such as sockets for pipe or for union complete all as specified and as directed by Engineer-in-charge.

S&F of 20mm bore Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by Engineer-in-charge.

S & F of 15mm bore PVC Connection with PTMT nut of length 600 mmcomplete all as specified and as directed by Engineer-in-charge.

S&F of 15 mm bore two way bip taps CP with flange complete all as specified and as directed by Engineer-in-charge.

S&F of 15 mm bore angle cock CP with flange complete all as specified and as directed by Engineer-in-charge.

S&F of CP health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook in clouding making connections and fixed in position, complete all as specified and as directed by Engineer-in-charge.

S&F of brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and as directed by Engineer-in-charge.

S&F Soap dish, vitreous China white of approximate size 160 x 160 x 90 mm embedded in the wall allcomplete all as specified and as directed by Engineer-in-charge.

S&F of PTMT towel ring of dia 200mm, complete all as specified and as directed by Engineer-in-charge.

S&F of swivel shower of CP with shower arm 150 mm size for fixing with 15 mm bore GI pipe complete all as specified and as directed by Engineer-in-charge.

S&f of 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and as directed by Engineer-in-charge.

S&F of 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engineer-in-charge.

S&F of 110mm dia PVC bends of any radius with access door complete all as specified and as directed by Engineer-in-charge.

S&F of 110mm dia PVC (SWR) branch piece single (single 'Y'/T) equal or unequal with access door complete all as specified and as directed by Engineer-in-charge.

S&F of 110mm dia PVC SWR vent cowl complete all as specified and as directed by Engineer-in-charge.

S & F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engineer-in-charge.

S & F of 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and as directed by Engineer-in-charge.

M&L for CI Nahani trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1(diameter of outlet 100mm) complete all as specified and as directed by Engineer-in-charge.

M & L for 15 mm bore steel tubing medium grade, galvanised fitting fixed complete to walls and ceiling or floor, complete all as specified and as directed by Engineer-in-charge.

M & L for 20 mm bore steel tubing medium grade, galvanised fitting fixed complete to walls and ceiling or floor, complete all as specified and as directed by Engineer-in-charge.

S & F of 1000 ltrs rotational moulded polyethylene water storage tanks multi layer (cylindrical vertical with closed top) incl connecting up pipes securing access covers etc as, complete all as specified and as directed by Engineer-in-charge.

S&F of 20 mm dia PVC ball cock (PVC float valves) complete high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut, complete all as specified and as directed by Engineer-in-charge.

M & L for reinforced concrete pipes, class NP2, drain pipes including collar of radius 150mm laid in trenches and jointed complete all as specified and as directed by Engineer-in-charge.

M & L for Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in Cement concrete 1:3:6 type C-2 for 150mm dia pipe complete all as specified and as directed by Engineer-in-charge.

M&L for fixing Plastic dividing strips,1.5mm thick and ditto dividing strips, 38mm deep inserted in position to conform to design complete all as specified and as directed by Engineer-in-charge.

M&L for point wiring complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated Sunden terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes upto a size of 200 x 300mm and above this size not less than 1.63 mm thick duly painted with aluminium inside and anticorrosive paint outside, concealed in walls, with 3mm thick bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be done through proper size copper/brass thimbles. Where concealing of conduit is not feasible i.e. on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost for one light, complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 126 as above but for one fan point controlled by one switch, complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 126 as above but for One socket out let 5/6 amps point on the independent board, complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 126 as above but for One socket out let 5/6 amps point on the same board, complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 126 as above but for One bell/buzzer point controlled by one bell push button, complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 126 as above but for wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board, complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 126 as above but for wiring with 4 sq mm single core copper conductor for AC point on the independent board, complete all as specified and as directed by Engineer-in-charge.

S&F of modular switch type 5/6 amps single pole one way, complete all as specified and as directed by Engineer-in-charge.

S&F of switch piano flush type 5/6 amps single pole one way, complete all as specified and as directed by Engineer-in-charge.

S&F of modular switch 6 amps one way 1 module, complete all as specified and as directed by Engineer-in-charge.

S&F of Socket, 6A - 2/3 pin combined 2 module, white ivory finish modular type, complete all as specified and as directed by Engineer-in-charge.

S&F of socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type, complete all as specified and as directed by Engineer-in-charge.

S&F of Socket, 6A/16A- 2/3 pin combined 2 module, white ivory finish modular type, complete all as specified and as directed by Engineer-in-charge.

S&F of socket outlet 2 in 1, 5 Pin, 5/15 amp, multipurpose 230 volt flash type complete all as specified and directed by Engr-in-Charge.

S&F of modular switch type 15/16 amps single pole one way, complete all as specified and as directed by Engineer-in-charge.

S&F of switch piano flush type 15/16 amps single pole one way, complete all as specified and as directed by Engineer-in-charge.

S&F of modular bell push 6A 1 Module , complete all as specified and as directed by Engineer-in-charge.

S & F of Metal flush box 1/2 module, complete all as specified and as directed by Engineer-in-charge.

S & F of Metal flush box 3 module, complete all as specified and as directed by Engineer-in-charge.

S & F of Metal flush box 4 module, complete all as specified and as directed by Engineer-in-charge.

S & F of Metal flush box 6 module, complete all as specified and as directed by Engineer-in-charge.

S & F of Metal flush box 8 module , complete all as specified and as directed by Engineer-in-charge.

S & F of White cover plate with frame, 1 module, complete all as specified and as directed by Engineer-in-charge.

S & F white cover plate with frame, 2 module, complete all as specified and as directed by Engineer-in-charge.

S & F of White cover plate with frame, 3 module, complete all as specified and as directed by Engineer-in-charge.

S & F of White cover plate with frame, 4 module, complete all as specified and as directed by Engineer-in-charge.

S & F of White cover plate with frame, 6 module, complete all as specified and as directed by Engineer-in-charge.

S & F of White cover plate with frame, 8 module, complete all as specified and as directed by Engineer-in-charge.

S&F of ceiling rose, bakelite, surface type, 220/240 volts, three terminals, complete all as specified and as directed by Engineer-in-charge.

S & F of Fan step regulator, 120W - 2 module AC 50 Hzs rotary step white/ivory finish, complete all as specified and as directed by Engineer-in-charge.

S & F of stepped type electronic fan regulator not less than 80 watt, complete all as specified and as directed by Engineer-in-charge.

S&F of Ceiling rose, surface type with back plate, three terminal /PVC/ polycarbonate, isolated body, complete all as specified and as directed by Engineer-in-charge.

S & F of lamp holder, isolated body, with back plate suitable for batten/angle fittings, complete all as specified and as directed by Engineer-in-charge.

S & F of Wall mounted slim LED batten 20W 4' long, min output 120 Lumen/watt PF>0.95,surge protection,> 4KV, THD:<10% with extruded aluminium housing, with integrated LED driver complete all as specified and directed by Engr-in- charge.

S & F of LED street light fittings 35 watt min output 110 Lumen/ watt PF>0.95, surge protection>5 ,THD: <10%in aluminium PDC housing, toughened glass cover with IP66 protection complete all as specified and as directed by Engineer-in-charge.

Supply and fixing of LED luminaire 600 mm x 600 mm, 35/36 watt, min 110 Lumen/watt P.F>0.95 surge protection>4 KV ,THD:<10% with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size, complete all as specified and as directed by Engineer-in-charge.

S&F of Mirror Light 9/10 Watt LED with constant current electronic driver, all accessories including provision of three core PVC cable of copper conductor and making connection, complete all as specified and as directed by Engineer-in-charge.

S&F of Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB'S/ isolators complete all as specified and directed by Engr-in-Charge.

S&F of Sheet metal enclosure for 12 way Distribution Boards (DB’s), double door, single pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB'S/ isolators complete complete all as specified and directed by Engr-in-Charge.

S&F of MCB, Single pole & neutral 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete as specified and directed by Engr-in-Charge.

S&F of MCB, Single pole & neutral 40 Amps to 100 Amps, 220volts, ‘C’ curve, 10 KA all complete all as specified and directed by Engr-in-Charge.

S&F of MCB, Single pole, 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete all as specified and directed by Engr-in-Charge.

M&L for sub main wiring complete with 2 run of 4 sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FR-LSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of required size medium grade (MMS) with all connected accessories such as Bend, Tee, Elbow, Short pieces etc concealed in wall/roofs/floors and including one run of 4 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FR-LSH type as earth continuity conductor connected to common earth dolly and including cheese cutting and filling the same with cement mortar and finished with putty and making good the disturbed surfaces to match with existing surface as required for concealed work complete all as specified and directed by Engineer-in-charge. (Note : (i) Two runs of cable with one run earth wire and PVC conduit shall be measured as one length. (ii) Extra length of cable required for connection to DBs shall be deemed to be included in the unit rate and shall not be measured separately. (iii) Earth wire shall run inside the conduit. (iv) Suitable colour code of wire must be ensured for phase/natural/earth. (v) All surface cutting/making good for wiring/switch board/junction box/DB etc are included with unit quoted rate.)

M&L for sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FR-LSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of required size medium grade (MMS) with all connected accessories such as Bend, Tee, Elbow, Short pieces etc concealed in wall/roofs/floors and including one run of 6 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FR-LSH type as earth continuity conductor connected to common earth dolly and including cheese cutting and filling the same with cement mortar and finished with putty and making good the disturbed surfaces to match with existing surface as required for concealed work complete all as specified and directed by Engineer-in-charge. (Note : (i) Two runs of cable with one run earth wire and PVC conduit shall be measured as one length. (ii) Extra length of cable required for connection to DBs shall be deemed to be included in the unit rate and shall not be measured separately. (iii) Earth wire shall run inside the conduit. (iv) Suitable colour code of wire must be ensured for phase/natural/earth. (v) All surface cutting/making good for wiring/switch board/junction box/DB etc are included with unit quoted rate.)

M&L for earthing with galvanised steel earth plate electrode of size 600mmX600mmX6mm thick buried directly in ground (earth pit not less than 2.25 m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel using GI or steel wire 4mm dia as earthing lead as shown in electrical plate No.3 of SSR Part-I connected to earthing test point all specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC (1:3:6) type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe , 15mm dia GI medium grade earth lead protection pipe and pre-cast earth pit cover 50mm thick made of RCC (1:1.5:3) type A-1 duly reinforced with 8mm dia TMT bar @150c/c both ways, one lifting handle made out of 10mm dia TMT bar 250 mm long embedded in cover slab and cover, wire, copper lugs etc mesh, charcoal and common salt in alternate layer of 15 cm thick complete all as specified and directed. (Notre: Galvanised iron wire of 4mm dia upto 7.5m long including testing is deemed to be included with quoted rate).

S&F of ceiling fan complete with blades, down rods and accessories including provision of hook for hanging ceiling fan, 230 V, 1200 mm sweep. BEE star rated with Brushless direct current (BLDC) motor complete all as specified by Engr in charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm and provision of 3 core flexible multistranded copper conductor of size 0.75 Sqmm from ceiling rose to fan all as specified and directed by Engineer-in-charge.

Supply and fix SPN sheet metal enclosures with two pin and earth plug and socket complete with one SP MCB 20 Ampcomplete all as specified and as directed by Engineer-in-charge.

Supply installation, commissioning and testing of electric water heater, storage vertical type, BEE 5 star rated 25 ltrs capacity 230 volts AC 50 Hz comprising of high wattage heating element for instant heating extra thick SS inner tank of superior 304 grade, rust & shock proof ABS outer body, non-ferrous pressure plate with and including provision of 04 Nos grouting bolts suitably flush to wall or any other surfaces and connection pipe for hot and cold water supply 25 lts BEE 5 Star rated complete stranded copper conductor cable/ flexible chord, complete all as specified and as directed by Engineer-in-charge.

M&L for street light bracket, made out of GI pipe medium grade) 25 mm bore, 1.2 m long bend to shape and fixing/grouting with wall using 2 Nos 25 x 5 mm size MS FI clamps with bolts, nuts & washers complete including drilling as necessary and two coats of Aluminium paint over a coat of Red oxide primer all as specified & directed by Engineer-in-charge.

Supply and laying in Trenches GI water Tubing medium grade of 20 mm dia including all fittings such as sockets, bends, elbows, Union etc complete all as specified and as directed by Engineer-in-charge.

M & L for Drilling and tapping cast iron water mains (in position) for branch connections of the internal dia 20mm, complete all as specified and as directed by Engineer-in-charge.

M & L for Straight plain brass ferrules (or connecting screws) screwed both ends and fixed, complete all as specified and as directed by Engineer-in-charge.

M&L for Cutting of Existing GI pipe of dia 50 mm and inserting of Tee in existing pipe for connecting new pipe complete all as pacified and as directed by Engineer-in-charge.

Supply and laying of brick protection for protection of cable over sand cushioning cables inside the trench by using common brunt clay building bricks sub-class “B” old size brick and flat and width wise along the axis of the trench complete all as specified and as directed by Engineer-in-charge.

M&L for sand cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep including required watering and consolidation after laying and stretching the cable, complete all as specified and as directed by Engineer-in-charge. (Note: Only punned down volume of sand to be measured)

Supply and laying of XLPE insulated, LT armoured electric cable with aluminium stranded conductor 1100 volts grade, cross-sectional area 16 sqmm, 4 core laid in trenches/pipes/ducts/wall/borings with necessary cable lugs and glands, nuts, bolts and washers etc and testing complete all as specified and directed by Engineer-in-charge. (NOTE: Excavation/earth work, sand cushioning, cable cover/brick shall be measured and paid separately if required)

Supply and laying of XLPE insulated, LT armoured electric cable with aluminium stranded conductor 1100 volts grade, cross-sectional area 16 sqmm, 2 core laid in trenches/pipes/ducts/wall/borings with necessary cable lugs and glands, nuts, bolts and washers etc and testing complete all as specified and directed by Engineer-in-charge. (NOTE: Excavation/earth work, sand cushioning, cable cover/brick shall be measured and paid separately if required)

M & L for laying of GI pipe light grade across road for cable protection complete of size 40mm complete all as directed by Engineer-in-charge.

M & L for Horizontal boring of holes, under road/ pavement / hard standing etc., not exceeding 10 Metres in length, in any type of soil, suitable for passing through up to 50 mm bore, galvanised steel tubing, complete all as specified and as directed by Engineer-in-charge. Note - The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.

M/S A.B. MITRA (BID ID -3496510)

DEEP NIRMAN (BID ID -3496289)