Repair / Replacement LT panel, LT Overhead line, cable, MCCBs, Changeover, street light pole, old FTL / MH fitting, solar light, high mast light, street light panel and connected accessories at BTR, MH, KK Ranges, New KLP and ACCandS under GE (N) Ahm

Amount

Supply & Fixing and testing in replacement of LT cable 1100 volts grade XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cable (heavy duty) with aluminium conductor suitable for following sizes laid in trenches, on poles and in ducts complete all as specified and directed by Engr in charge. size 120 sq mm 3½ core

All as per item No. 01 but size 70 sq mm 3½ core

All as per item No. 01 but size 50 sq mm 3½ core

All as per item No. 01 but size 25 sq mm 4 core

All as per item No. 01 but size 16 sq mm 4 core

All as per item No. 01 but size 10 sq mm 4 core

All as per item No. 01 but size 10 sq mm 2 core

Supply and replacement of 1100 volts grade heavy duty cable PVC insulated aluminium stranded conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension GI wire, twin core cable flat or circular with size 4sqmm. Note : Rate of 4 mm GI wire included in quoted rate

All as per Item No 8 above but 10 sqmm 2 Core

All as per Item No 8 above but 16 sqmm 2 Core

Excavation in trenches nexc 1.5 mtr in depth and not exceeding 1.5 Mtr wide for laying of cable/pipe etc and getting out in soft and loose soil complete all as specified nad directed.

Returning filling in trenches excavated soil including spreading levelling watering and well ramming in layers n.exc 25 cm thick each layer as in soil complete all as specified nad directed..

Removing excavated materials n.exc 50 mtr depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

Supply & laying of DWC(Double wall corrugated) HDPE pipe ISI marked with IS 16205 part 24 ( Pipe colour orange) of outer dia 50 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable icluding coupler and bends etc complete all as specified and directed by Engineer-in-Charge.

Supply & laying of DWC(Double wall corrugated) HDPE pipe ISI marked with IS 16205 part 24 ( Pipe colour orange) of outer dia 63 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable icluding coupler and bends etc complete all as specified and directed by Engineer-in-Charge

M/L for GI Tubes,of size 40 mm dia Medium grade, galvanised, with all fitting , laid in trenches for protection of cable in road /drain crossing complete all as specified and as directed.

M/L for GI Tubes,of size 50mm dia Medium grade, galvanised, with all fitting , laid in trenches for protection of cable in road /drain crossing complete all as specified and as directed.

M/L for GI Tubes,of size 80mm dia Medium grade, galvanised, with all fitting , laid in trenches for protection of cable in road /drain crossing complete all as specified and as directed.

M&L for road cutting upto 300mm deep and 200mm wide for crossing GI pipe line through road including making good the disturbed surface by filling mass concrete( 1:2:4) etc complete all as specified and directed by Engineer-in-Charge. Note : Rate of mass concrete is included in quated rate.

Demolation of u/s cement concrete in coppings etc complete all as specified and directed by Engineer-in-Charge.

Material and labour in replacement of 40mm dia GI Pipe light grade ISI Marked with all fittings laid in trenches , fixed to walls / poles with FI Clamps of size 40x5 mm all as directed.

Material and labour in replacement of 50 mm dia GI Pipe light grade ISI Marked with all fittings laid in trenches , fixed to walls / poles with FI Clamps of size 40x5 mm all as directed.

M & L for PCC(1:3:6) type C-2 using 40mm grade stone aggregates as foundation of pole and similar work all as specified and directed.

M & L for PCC(1:2:4) type C-2 using 20mm grade stone aggregates for coping and similar work all as specified and directed.

S&F Shock Proof, Rust Proof, Fire Retradrant, Non-transparent Kiosks Pole Box of size 200 x 175 x100 mm made of Engineering Plastic on Piece moulding for Outdoor type, Heavy duty with 4 No. insulated Alunminium Bus-bar of 60 Amp capacity, mounted on Unbreakable Insulators MCB SP, 10 Amp, complete with Aluminium Lugs of suitable size upto 50 Sqmm including 2 No. Flat Iron 40x3mm Clamps with suitable size Mild Steel Bolts, Nuts & Washers, etc. including Taking down Unserviceable Pole Box of any description from any Height, complete all as specified and as directed.

Supply and fixing wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, Three core cable in surface/recessed as required 2x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire (From PVC Junction box to Security light)

Supply,installation,testing and commissioining factory made LT feeder pillar panel CPRI approved, size of panel 1.0 x 0.3 x 0.6 mtr as per CPRI Specification,double door floor mounted outdoor type,as per IP-65 grade,made out of CRCA sheet 3.15 mm thick of outer body with Aluminium bus bar 300 Amps,4 strip,(3 phase & Neutral) complete drilled,insulated with colour coaded insulation tape,mounted on insulators etc. Panel should be dust proof,vermin proof,powder coated with 7 tank process locking should be screw type,mechanical type,inter locking,should have danger notice for 415 volt,AC,mounted on 50 x50 x6 mm angle iron frame having minimum 2 feet ground clearanceduly embedded in and including PCC block(1:2:4) type B1 foundation for fixing of panel complete including ternination of all incoming and outgoing cables with suitable size thimbles/lugs, glands , Nuts & Bolts complete all as required and directed.( Main Panel) (i) Incoming MCCB 4P, 160 Amp, 36 KA,theRMal and magnetic adjustable -01 No ( Ics = 100% Icu) (ii) Outgoing MCCB 4P 63 Amp, 25 KA -05Nos ( Ics = 100% Icu) (v) Digital voltmeter & Ammeter with necessary CTs (vi) Internal wiring with PVC insulated, multi stranded copper conductor cable, 1100 V grade, IS 694 marked of approriate size but not less than 2.5 sqmm (vii) Phase indicating LED lamps (R-Y-B) -01 SET (viii) Spare chamber for MCCBs - 01 Nos

Supply,installation,testing and commissioining factory made LT feeder pillar box ( bus bar chamber) , size of bus bar 600 x 600 x350 mm,double door floor mounted outdoor type,as per IP-65 grade,made out of CRCA sheet 3 mm thick of outer body of suitable size with aluminium bus bar 200 Amps,4 strip,(3 phase & Neutral) complete drilled,insulated with colour coaded insulation tape,mounted on insulators etc with RYB indicater,panel should be dust proof,vermin proof,powder coated,locking should be screw type,mechanical type,inter locking,should have danger notice for 415 volt,AC,mounted on 50 x50 x6 mm angle iron frame having minimum 2 feet ground clearanceduly embedded in and including PCC block(1:2:4) type B1 foundation for fixing of panel complete including ternination of all incoming and outgoing cables with suitable size thimbles/lugs and glands Nuts & Bolts etc complete all as specified and directed by Engineer-in-Charge. (a) Aluminium Bus-bar 4 Strip, 450mm long, 200 Amp, 415 Volt - 01 Set (b) provision of Outgoing ways 5 nos of LT cables of size 16 to 95 Sq mm Notes:- 1. The rates Quoted shall include for earth work,Plinth protection around the panel apprx 75cm and excavation for angle iron frame for foundation of panel board up to 0.50 m below GL in any type of soil and PCC 1:4:8 type D2 filling in foundation. The ground clearance of panel board shall be 0.40 M from GL to the bottom of panel board.

Supply M&L for earthing complete with galvanized steel earth plate electrode of size 60cm X 60 cm X 6 mm buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of plate not less than 1.5 m below the normal ground level connected to GI earth strip 25 x4 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel, protected by GI pipe light grade 40mm bore all as shown on electrical plate No 3 of SSR Part-I connected to earth test point electrode, PCC pit with RCC cover, funnel with wire mesh, watering pipe 20mm dia protection pipe etc and testing on completion complete all as specified and directed. Note No 1 :- The unit rate shall also include for earth work in hard/dense soil, PCC (1:3:6) type C1 chamber, RCC 1:2:4 type B-1 cover 50 mm thick reinforced with 8 mm dia TMT bar @ 150 mm c/c both ways, funnel with watering pipe 20 mm dia medium grade, GI protection pipe light grade 40 mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (Notes) under sub-heading earthing, specified on Serial Page No 389 of SSR Part –I. Note No 2 :- Earthing strip and GI protection pipe beyond 7.5 m will be measured and paid separately if required (iii) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself.

M & L for Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire all as shown in Plate No. 2 to the earthing test point all as specified and indicated including testing on completion Note No 1 :- The unit rate shall also include for earth work in hard/dense soil, PCC (1:3:6) type C1 chamber, RCC 1:2:4 type B-1 cover 50 mm thick reinforced with 8 mm dia TMT bar @ 150 mm c/c both ways, funnel with watering pipe 20 mm dia medium grade, GI protection pipe light grade 40 mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (Notes) under sub-heading earthing, specified on Serial Page No 389 of SSR Part –I. Note No 2 :- Earthing strip and GI protection pipe beyond 7.5 m will be measured and paid separately if required (iii) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself.

Dismantling carefully the existing LT overhead line ACSR conductor with cross arm of any size from its position by necessary disconnecting of conductor and removing complete and deposite in MES stored yard all as specified and as directed

Dismantling of unserviceable existing cross arms made from channels, angles and unserviceable FI clamps, nuts, bolts etc from OH line and removing complete all as specified and as directed

Dismantling stay assembly complete all as specified and directed

S &F PCC Cable route Indicator with suitable reinforcement of size 50 x 10 x 10 cm with letter inscribed on both side as "MES LT CABLE " of specified front side not less than 30 mm as directed and mounted on PCC 40 x 30 x 30 cm complete using PCC 1: 2:4 B1 using 20 mm graded stone aggregate and including painting using cement based paint to the satisfaction of engr in charge

Supply and fixing in replacement of MCB TPN 63 Amps with breaking cap 10 KA and connecting all as directed .

Supply and fixing in replacement of MCB DP, 40 Amps with 10 KA breaking / rupturing capacity including neccssary connection complete all as directed.

Supply and fix in replacement MCB, SP, 6 to 32 Amps 10 KA breaking / rupturing capacity capacity including necessary connection with suitable size of copper cable complete all as directed.

M & L for painting of LT poles of any type (with hydrolic vehicle / ladder) including cross arms, channel, flat iron clamps etc 9 mtr long in two coats of aluminium paint and one coat of red oxide as primer including writing of pole nos (Yellow circle and Number in black) and providing 3 Nos of radium with width 50 mm size band / strap with Red, Yellow, Green colour 300 mm apart from plinth block around the pole etc complete as all as specified and directed in Engr-in- Charge. Note:- Hydrolic Vehicle / Ladder for painting is responsibility of contractor and rate of Hydrolic vehicle and ladder including in quoted rate.

M&L Heat shrinkable straight through joint, with including jointing materials and necessary earth work suitable for 1100 Volts , XLPE LT cable of size 16-25 sq.mm , 3.5/4 core, including fixing, jointing and testing complete all as specified and as directed.

M&L Heat shrinkable straight through joint, with including jointing materials and necessary earth work suitable for 1100 Volts , XLPE LT cable of size 35-95 sq.mm , 3.5/4 core, including fixing, jointing and testing complete all as specified and as directed.

M&L Heat shrinkable straight through joint, with including jointing materials and necessary earth work suitable for 1100 Volts , XLPE LT cable of size 120-240 sq.mm , 3.5/4 core, including fixing, jointing and testing complete all as specified and as directed.

M & L for aluminium cable lugs of size upto 50 sqmm flat head in Aluminium conductor/cable fixing with Nuts, bolts & washers to junction point as directed. (Note-To be measured only, fixed at places other than with heat shrink joints)

M & L for aluminium cable lugs of size 70,95,120,150,185, 240,300 sqmm flat head in Aluminium conductor/cable fixing with Nuts, bolts & washers to junction point as directed.

S& F in replacement sign boards for MES installations of size 1200x 900mm made out with angle iron 40x40x 6mm as framing covered both side with 2 mm thick aluminium sheet rivetting on frame covered with retro reflective sheet & 100mm high letters as diredcted. Th sign board to be fixed on 2 No. 40x40x6mm angle iron legs embedded in PCC(1:4:8) using 40mm graded stone aggregate including necesary excavation complete at the installation etc complete all as specified and directed by Engr-in-charge Note : Matter on sign board supplied by Engr in Charge

Dismantling of unserviceable insulator of any type complete from its position and removing all as specified and as directed

M&L for restringing of LT over head line consisting of 4 conductors by dismantling, taking down, repairing wherever required including cutting, re-jointing andrestringing in situ, with proper sag, binding to insulator with and including aluminium binding wire complete all as per specified and directed, Note : One RM consist 4 run of ACSR conductor

M &L for construction of plinth (of size 2000mm x 2000 mm x 1500 mm) including excavation in trenchs in any type of soil,PCC 1:4: 8 in foundation fly ash bricks machinaryin cement mortor1 : 6 ,filling with moorum inside the plinth and RCC 1:2:4 over plinth including 16 mm bar reainfrocement with center to centre distane 100mm and external surface of masonary shall be plasterd with cement morter 1:4 and painted with weather coat paint ( double coat paint ) of shade as directed by Engr In Charge complete all as specified and directed by Engr in charge

Dismantling and taking down carefully the defective Highmast light fittings from high mast pole by mechanically/ manually and removing the unseviceable light fitting from pole and supply and fixing led flood light 120 watt,lumen 20000 with 10 KV surge protection in built and reassembling the same pole , and refixing at its original location , including reconnections with suitable length and size of capper/Aluminium wire as per existing and testing / commissioning complete all as specified and directed.

Lifting the Highmast pole 16 mtr height by crane from its own location with opening the nut boltt and washers , greasing the steel wire rope and fixing with pulley and reassembling and refixing at its orginal location, including reconnections and testing commissioning complete for smooth operations all as specified and directed. Note: (i) Rate for Crane and labours is being to be includes in Quoted rates. (ii) Rate of sundry items like grease, cotton waste, nut , bolt and washers are deemed to be quoted rates.

Supply and fix in replacement of MCB TPN, 63 Amps 10 KA breaking / rupturing capacity capacity 415 volt , 50 HZ conforming to IS 60898-1 including necessary connection with suitable size of copper cable complete all as directed.

Supply and fix in replacement of timer switch Astronomical type, 240volt, 50/60 Hz 16 amp/250VAC resistive of Make : L & T/ Indoassian and standard.

M & L for replcement of Chain sprocket in Highmast Light all as specified and directed

Supply and fix in replacement of brass batten holder for fixing of gate light.

Supply and fixing in replacement of Triple pole and Neutral On load change over switch 100 Amp 415 volt AC 23 A 50 HZ ,with insheet steel encloser conforming to IS 60947 1 & 3 fixing on Street light Pole with 32x4mm of MS Clamp and suitable size of nut, bolt and washers all as specified and directed.

Supply and fix in repairs change over switch existing panel, wall or LT pole of any size and any type on load type, triple pole and neutral, 63 Amps, 415 V, 50 Hz front handle operated, including connecting and testing all as directed.

Supply and fixing with replacement of MCB SP 6 to 32 Amps with PVC Enclouser fixing with pole or wall for individual street light/ security light control with suitable size of clamp nut , bolt and washers.make: C&S/ Indoassian/L&T. Note: Rate of MS Clamp is include in Quoted Rates.

M&L Street Light Fitting Bracket made out from GI Pipe 40 mm Bore (dia), Light Grade, not exc. 1.20 Metre long, bend to required shape and fixing to Poles, etc. with and including Mild Steel Flat Iron Clamps 40x5mm of suitable Length, 2 No. Nuts, Bolts, Washers, etc. including Painting with One coat of Red Oxide Zinc Chrome Primer and Two coats of Aluminium Paint to all Mild Steel Works incuding taking down existing complete all as specified and as directed.

Material and labour for street light control board / box of size 0.50 X 0.50 X 0.20 m made out of 1.60 mm thick MS sheet fixed / mounted on pole by means of 2 Nos of FT clamps of size 25 X 3 mm comprising the following enclousers and connecting with suitable size of copper cable all as directed:- a) MCB, TPN, 63 Amps, - 01 No MAKE:L & T/ STANDARD OR equivalent in makes mentioned in list of makes in Appendix `C' b) Timer switch, Astronomical type operating on 110 / 240 / 415 Volts, 50 Hz MAKE: L&T OR equivalent in makes mentioned in list of makes in Appendix `C' c) Contactor ML 2, 63 Amps,415 Volt - 01 No MAKE: CAT No SS90701 OF L&T OR equivalent in makes mentioned in list of makes in Appendix `C' d) All MCB,Contactor should be connected through HRC fuse

Supply and fix in replacement of Intelligent smart sensor based LED street light with automatic switch- ON and switch OFF operation based on ambient lux level,cast alumonium housing polycarbonate diffuser,secondary optical lenses,complete and wired with all accessories IP 65/66 protection with luminaries 45 watt, with inbuilt surge protection 10 KV and impact resistance IK07 fixed with suitable size of GI Bracket of length 1.2 Mtr,Clamp,Nut, Bolt and washer , connection with 1.5 sqmm 3 run copper wire from junction box to streeght light and 4 sqmm 2 core aluminium service cable pvc insulated 2.5 RM per fitting where over head line existing for connection of street light to over head conductor complete all as specified and directed.

Supply and fixing in replacement of Intelligent smart sensor based auto dimmable LED street light,45 watt, with inbuilt surge protection of 10 KV dimming opetions of 100% to 30% of the rated wattage on sensing of movement/occupancy,within 8 Mtr radius,IP 66 Thd less than 10% with more than 110 lumens /watt,housing made from cast alumonium pressure die cast,clear toughened glass and secondary optics,high powel LEDs complete with suitable size of GI Bracket of length 1.2 Mtr,Clamp,Nut, Bolt and washer , connection with 1.5 sqmm 3 run copper wire from junction box to streeght light and 4 sqmm 2 core aluminium service cable pvc insulated 2.5 RM per fitting where over head line existing for connection of street light to over head conductor complete all as specified and directed.

Supply and fixing in replacement of Intelligent smart sensor based auto dimmable LED street light,60 watt, with inbuilt surge protection 10 KV, dimming opetions of 100% to 30% of the rated wattage on sensing of movement/occupancy,within 8 Mtr radius,IP 66 Thd less than 10% with more than 110 lumens /watt,housing made from cast alumonium pressure die cast,clear toughened glass and secondary optics,high powel LEDs complete with suitable size of GI Bracket of length 1.2 Mtr,Clamp,Nut, Bolt and washer , connection with 1.5 sqmm 3 run copper wire from junction box to streeght light and 4 sqmm 2 core aluminium service cable pvc insulated 2.5 RM per fitting where over head line existing for connection of street light to over head conductor complete all as specified and directed.

M & L for repairing of Highmast panel box by replacing of MCB TPN, Timer switch, Contactor and also repairing the Panel box by welding of hinges, replacement of Lock etc all as per specified and directed. Note: (i) MCB TPN, Timerswitch and Contactor are paid separately. (ii) Rate Includes welding,Lock and keys , Painting in two coats of synthetic enamail and one coat of primer red oxide,

Supply and fix in replacement of MS Clamp 25x3mm with nut bolts and washers duely painted in two coats of aluminium paint and one coat of red oxide all as specified and directed by Engr-in -Charge.

M&L for road cutting upto 300mm deep and 200mm wide for crossing GI pipe line through road including making good the disturbed surface by filling mass concrete complete all as specified and directed.Note : Rate of mass concrete included in quated rate.

S &F PCC Cable route Indicator with suitable reinforcement of size 50 x 10 x 10 cm with letter inscribed on both side as "MES LT CABLE " of specified front side not less than 30 mm as directed and mounted on PCC 40 x 30 x 30 cm complete using PCC 1: 2:4 B1 using 20 mm graded stone aggregate and including painting using cement based paint to the satisfaction of engr in charge

Mahindra Electric Stores

Maruti Abhiyantriki

KAMINS CARE

M/s. Chhtrapati Construction(Propa. Lokesh Anant Salunke)