MAINTENANCE WORKS DAY TO DAY ONLINE COMPLAINT AT CERA MD ACCN UNDER AGE B/R II AND REPAIRS MAINTENANCE OF FITTINGS FIXTURES REWIRING AND REPLACEMENT OF DBS MCBS LED FITTINGS AT AMBC BUILDINGS UNDER AGE EM MAINT AT INA EZHIMALA

Amount

Notes for all items of BOQ:- 1. The contractor should visit the site before quoting the tender to know the working condition of the station. 2. All requisite safety measures are to be adopted by contractor on site. 3. The contractor shall provide and deploy sufficient electrician ( as approved by GE/ Engineer in charge) shall report at 9.00 hrs to JE E/M / Engineer in charge to collect the complaints job card in working days and complete the same complaint within 24 Hrs. 4. The complaints shall be rectified within 24 hrs if the complaints is/are not attended / not completed with in 24 hrs ( except repair/ replacement of major items) recovery will be done at Rs. 500 per complaint per day. 5. For major parts like replacement of MCB, DBs, MCCBs etc should be rectified within 3 working days, if the contractor not rectify within time then recovery will be done at Rs.1000 per complaint per day. 6. After completion of job work complaint, the contractor has to produce job card duly signed by user & JE /Engineer in charge. 7. If contractor failed to provide their electrician to attend the complaints then recovery will be done at Rs. 1000 per day. 8. The Contractor should procure minimum 50% of the materials for all items as per BOQ (other than paints) mentioned in this CA within 20 days after getting sample approval and kept in safe custody so that no delay in work due to non-availability of materials will be faced. Contractor should ensure during the cause of work that he has minimum 25% of materials with him till the completion of work. If contractor fail to complete the work within contract due to lack of fittings, a penalty of 20% shall be applicable on quoted rates by the contractor. 9. In repair works, rate quoted for demolition/dismantling/taking down is deemed to be inclusive of removing the same from site and dumped outside INA Ezhimala. 10. In maintenance works, the contractor should maintain separate registers for plumbing and carpenter repair works. Day to day complaints should be noted in those registers with Sl nos of complaints, location, qty of work, status of complaints and signature of in charge and stamp of the office. Format will be given from concern AGE office. The contractor should obtain the signature of in charge on the same day of work. These registers to be submitted to JE(Civil) on every weekend without fail. 11. The contracts involving working at elevated locations of buildings, contractor should ensure proper safety arrangements as per norms. Wearing safety belts and helmets are mandatory. A penalty of Rs 1000 per day will be recovered from contractor if safety norms are not followed. 12. The plumbing complaints resulting wastage of water should be rectified within 12 working hours and if contractor fail to fullfill this, a recovery of 10% of rate quoted for relevant item will be charged from contractor in this regard. 13. After completion of work, no stores/debris/loose items be kept at work site or dumped inside INA. Entire area to be cleared and waste material be taken outside INA.

Taking up or down steel tubing and connections, 25 or 32 mm bore incl cleaning and removal to store complete all as specified and as directed.

Taking up or down steel tubing and connections, 20 mm bore incl cleaning and removal to store complete all as specified and as directed.

S&F 32mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

S&F 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

S&F 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

Repair/removal of air lock in internal water supply system for pipe of any dia complete all as specified and as directed.

Dismantling single layer of mangalore pattern tiles in roofing complete all as specified and as directed.

M&L for roof tiles mangalore pattern interlocking at side joints, laid dry complete all as specified and as directed.

All as per item No.09 above but except tiles complete all as specified and as directed.

M&L for ridge or hip tiles to suit mangalore pattern or roofing tiles bedded and jointed in cement mortar 1:6 using water proofing compound complete all as specified and as directed.

M&L for preparation of new MP roof tile surfaces by cleaning the tiles and applying two coats of antifungal paint using UNIGLOSS deluxe multi surface paint over a coat of primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old MP roof tile surfaces by cleaning the tiles and applying one coats of antifungal paint using UNIGLOSS deluxe multi surface paint complete all as specified and directed by Engineer-in-Charge.

S&F anodised aluminium frame for below MP tiles in repair with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting / galvalume sheets, including aluminium frame any gauge, thickness as in roof covering etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated/tile pattern steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L for 10mm thick rendering in CM 1:3 on roof with water proofing compound surfaces finished even and smooth without using extra cement, complete all as specified and as directed. Note:- Water proofing compound shall be measured and paid separately.

M&L for preparation of roof surface by throughly wire brushed, washed, dried up, cleaned of all the foreign matters and dust, and applying bituminous primer @ 250gms/sqm, and then laying 4mm thick APP modified bituminous membrane with non woven polyster matt as reinforced weighting not less than 4.00kg per sqm, laid on primed surface with torch application method by providing overlap minimum 100mm longitudinal and 150mm on transerve direction. All angles and similiar projections should be sealed well with extra care to ensure full bondage, all joints and changes in direction should be curved with cement mortar 1:3 mixed with SBR latex @ 200ml /bag of cement complete all as specified and as directed.

S&F in repair 15mm bore chromium plated bib taps long body fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes including taking down of old items complete all as specified and as directed.

S&F in repair angular stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, chromium plated, fancy type, screwed both ends for iron pipe or for union and fixed, suitable for 15 mm bore pipe complete all as specified and as directed.

S&F in repair 15 mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

S & F in repair 125mm size brass chromium plated shower rose complete all as specified and as directed.

S & F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and as directed.

S&F in repair 15mm bore stop valves chromium plated cast copper alloy (long shank, fancy type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes (concealed type) complete all as specified and as directed.

S & F in repair PVC valve less syphonic action type flushing cistern low level with inlet ball valve float and handle including brackets of 10 ltrs capacity complete all as specified and as directed.

S&F in repair 32mm dia PVC flexible waste pipe for urinals/WHB/ sink etc complete all as specified and as directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S & F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repair vitreous china, wash down water closet (EWC), coloured with seat cover, closed pattern with flat bottom and cover with mild steel (CP) or aluminium hinging device fixed with necessary bolts complete all as specified and as directed.

S&F vitreous china squatting pan Orissa pattern size 630x450mm white with integral foot rest (excluding flushing cistern and flush ipe ) fixed in repair complete all as specified and as directed.

S&F in repair vitreous china wash basin,coloured (flat back) 550x 400mm excluding pillar tap, but including fixing brackets, cutting for and pinning in ends of brackets complete all as specified and as directed.

Demolition of brick work, PCC block or stone masonry built in cement mortar complete all as specified and as directed.

M&L for precast cement concrete block masonry with solid blocks type C1, 1:3:6 (20mm graded aggregate) exc 10 cm in width and set in cement mortar 1:6 complete all as specified and as directed.

M&L for laterite stone masonry walling of rubble, coursed, well bonded, bedded in cement mortar 1:6 complete all as specified and as directed.

Taking down cement plaster on bricks or stone walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and as directed.

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces with liquid water proofing compound, surface finished even and fair complete all as specified and as directed. Note:- Water proofing compound shall be measured and paid separately.

Supply only intergral waterproofing compound of approved quality complete all as specified and as directed.

M&L for preparation of new plastered surfaces and applying two coats of acrylic emulsion (exterior grade) over a coat of primer on wall all as specified and as per manufacturers instructions. Note:- The quoted rates is deemed to be inclusive of necessary scaffoldings and safety measures for safe doing of work at heights.

M&L for 15 mm thick rendering on stone masonry or faces other than fair faces of brick work in cement mortar 1:6 surfaces finished even and fair complete all as specified and as directed.

M&L for preperation of new plastered surfaces and applying two coat of acrylic emulsion paint (interior grade) on wall over a coat of acrylic primer all as specified and as per manufacturer's instructions.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish of the premises complete all as specified and as directed.

M&L for coloured Non-skid ceramic tiles (square/rectangular) 7 to 8mm thick in floors, area of each tile exc.0.06 sqm but n.exc 0.11 sqm, set and jointed in neat cement slurry and pointed in white cement mixed with matching pigment over and including 20mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles 350x250x7mm / 450x350x7 mm thick in vertical surfaces of stone/brick wall, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick backing coat plaster in CM 1:4 complete all as specified and as directed.

Taking down chowkats with shutter (without taking off shutter from the frame) exc 1.5 Sqm but n.exc 4.00 Sqm each complete all as specified and as directed.

S&F Pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges etc complete all as specified and as directed.

M&L for filling concrete inside frame in PCC 1:3:6, type C-0 complete all as specified and as directed.

S&F 30mm thick 1st class hard wood plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats including iron mongeries and builders hardwares complete all as specified and as directed.

S&F 30 mm flush shutters, solid core construction, with block board core and plywood face panels, commercial type both side including iron mongeries and builders hardwares complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surface exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Taking down chowkats with shutter (without taking off shutter from the frame) n. exc 1.5 Sqm each complete all as specified and as directed.

S&F solid PVC double door frame of size 50mm x 95mm made out of 5mm plain colour PVC sheet reinforced with M.S. tube, suppling & fixing in opening as per manufacturer's specification & drawing complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (styles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per manufacturer's specification & drawing with particle board core including iron mongeries and builders hardwares complete all as specified and as directed.

S&F in repairs aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire staple complete all as specified and as directed.

Dismantling cabinets boarding, any description, fixed in any position with screws incl all fittings complete all as specified and as directed.

S&F prelaminated particle board 18/19 thick exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

S&F 18/20 mm thick plywood, BWR grade, type BB, fixed with screws to timber frame work as in cup boards etc complete all as specified and as directed.

M&L for preparation of old painted surfaces exc 10cm width or girth and applying one coat of synthetic enamel paint on wooden surfaces complete all as specified and as directed.

M&L for preparation of new or previously untreated wood based surface exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Taking down shutters of any description exc 1.00 Sqm and n.exc 2.00 Sqm each complete all as specified and as directed.

Refixing of shutters of any description exc 1.00 Sqm and n.exc 2.00 Sqm in same opening after easing and adjusting complete all as specified and as directed. Note:- Serviceable shutters obtained from item No.60 above shall be reused.

Resecuring or easing and adjusting without taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and as directed.

S&F stainless steel telescopic channel drawers slides complete all as specified and as directed.

S&F stainless steel soft closing hydraulic hinges for shutter complete all as specified and as directed.

S&F in repairs continuous (piano) hinges brass bright finish or electro galvanised, width of flaps (when open) 30 mm complete all as specified and as directed.

S&F in repairs 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished complete all as specified and as directed.

S&F in repairs 4 levers brass lock cupboard, grade 1, size 50 mm complete all as specified and as directed.

S&F 75mm long aluminium handles, cast type, anodised complete all as specified and as directed.

S&F in repairs 75mm long aluminium handles, cast type, anodised complete all as specified and as directed.

S&F in repairs 150mm size extruded aluminium alloy handles fabricated type anodised complete all as specified and as directed.

S&F in repairs 75 mm size butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and as directed.

S&F in repairs 100mm stainless steel butt hinges, cold rolled medium weight complete all as specified and as directed.

S&F in repair 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections, fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S & F in repair 100mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and as directed.

S & F in repair 150mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and as directed.

S & F in repairs 100 mm size brass, 4 levers mortice lock, vertical type complete all as specified and as directed.

S & F in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and overall length of cover plate 140mm complete all as specified and as directed.

S&F in repair 300mm long ordinary MS rat tail rod pattern springs including roller plate complete all as specified and as directed.

S & F plastic seat cover (colour) closed pattern with flat bottom suitable for EWC including taking down old cover complete all as specified and as directed.

S & F in repair 20mm dia, D type, 60cm long cast copper alloy, chromium plated towel rail complete all as specified and as directed.

S&F in repair chromium plated soap tray fixed with CP brass screws complete all as specified and as directed.

Dismantling wall and and ceiling boards (fiber,pulp,insulation etc) or insulation boards/slabs/any thickness including cover fillets complete all as specified and as directed.

S&F hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and as directed.

S&F anodised aluminium snap grid frame work for false ceiling of size of grid 605 x 605mm complete all as specified and as directed.

M&L for 4mm thick non-asbestos fiber cement building boards fixed or laid/inserted to timber, GI/aluminium framework with screws complete all as specified and as directed.

S & F in repairs curtain rails, anodised aluminium alloy with fixing brackets, stops, rollers etc complete all as specified and as directed.

S&F in repair plastic finial of 28 to 29mm bore decorated type of any colour/pattern best quality to suit the curtain rod and fixed at the end of curtain rod with suitable adhesive complete all as specified and directed by Engineer-in-Charge. Make:- Aerolux/MEC/VISTA.

S&F in repair mild steel prepainting bracket to hold the curtain rod and fixed to wall (concrete /brick masonry) with the help of 2 Nos 50mm long steel screws and rawl plug including drilling with electric drill and making good the distrubed surfaces complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass ( any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/ spring clips and providing and fixing new ones complete all as specified and as directed.

M&L for 4mm thick sheet glass plain ordinary quality not exc 0.50 sqm in each pane and glazing with beading complete all as specified and as directed.

M&L for 5.5mm thick sheet glass plain ordinary quality exc 0.50 sqm in each pane and glazing with oil putty complete all as specified and as directed.

Dismantling the existing water tank and S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 500 litres incl ball brass valves complete all as specified and as directed.

S&F in repair ball brass valves, high pressure, with polythene float and flynut (25mm) complete, screwed for iron pipe or brass ferrule and fixed in repairs complete all as specified and as directed.

M&L for laying and pasting of bituminous strip of width 10cm of make 3M/BASF/ Dr. Fixit/ Forsroc on joints of galvalume sheet and RCC surfaces including cleaning of existing surfaces complete all as specified and as directed.

S&F in repairs rubber beading suitable size for windows complete all as specified and as directed.

Petty repairs to leakage of bib taps, pillar cock, stopcock by changing the spindal complete all as specified and as directed.

Petty repairs to leakage of concealed valve by changing the spindal complete all as specified and as directed.

Petty repair to high or low level flushing cistern by adjusting the float valve, leaking of PVC connection, PVC bend including replacing of rubber washer, check nuts plunger etc for any type of flush complete all as specified and as directed.

Pieces, small let in for making good where hinges, etc. have been removed from chowkhats or frames, joinery, etc.including painting or oiling to match if required complete all as specified and as directed.

S&F in repair small GI fittings 15mm, such as socket, tee, elbow etc as required at site (Unit for this item shall be one No for each one item) complete all as specified and as directed.

S&F in repair small GI fittings 15mm, such as reducer 20 x 15, reducer 20 x 25 tee of unequal size etc as required at site (Unit for this item shall be measured one No for each one item) complete all as specified and as directed.

S & F in repairs waste coupling PTMT 32mm dia for glazed ware basins etc with long screwed shanks and fly nuts flanged etc complete all as specified and as directed.

All as per item No.103 above but 40mm dia suitable for steel sink complete all as specified and as directed.

Taking down defective/damaged water storage tank cover and supply & fix polyethylene tank cover with necessary locking arrangement all as specified and directed at site.

S&F PVC magnet catcher fixed with screws to wooden frames complete all as specified and as directed.

M&L for PVC lipping edge tape fixed with nails/glue complete all as specified and as directed.

S&F 75mm long hasp and staple, safety type, stainless steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F in repair harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as directed.

S&F in repair grating doom 100mm dia of CP with or without wastage hole complete all as specified and as directed.

Taking down existing water proofing treatment of any description and removal rubbish off the premises complete all as specified and as directed.

Dismantling of structural steel work including doors etc complete all as specified and as directed.

S&F steel work in tubular trusses (tubular, angle, square and rectangular etc ) including erection, shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 for round tubes complete all as specified and as directed.

Erection and fixing only steel work in tubular trusses (tubular, angle, square and rectangular etc ) including shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 for round tubes complete all as specified and as directed.

Cleaning and removing all scales and dirts etc from tanks and from mouths of circulating pipes etc. of capacity exc 250 and n.exc 500 ltrs complete all as specified and as directed.

M&L in replacement of old unserviceable sub main wiring using 4 runs of 10 sq mm FRLS, IS 694 PVC insulated copper conductor 1100 Volts grade conforming to IS specification drawn through and including PVC conduit of suitable size not less than 32mm dia medium grade surface on wall along with 1 runs of 10 sq mm PVC insulated copper conductor FRLS cable as earth lead connected to common earth dolly and including taking down old unserviceable wiring and making good the existing disturbed surface using wall putty and matching colour emulsion paint complete all as specified and directed by Engr-in-charge.

M&L in replacement of old unserviceable sub main wiring using 4 runs of 6 sq mm FRLS, IS 694 PVC insulated copper conductor 1100 Volts grade conforming to IS specification drawn through and including PVC conduit of suitable size not less than 25mm dia medium grade surface on wall along with 1 runs of 6 sq mm PVC insulated copper conductor FRLS cable as earth lead connected to common earth dolly and including taking down old unserviceable wiring and making good the existing disturbed surface using wall putty and matching colour emulsion paint complete all as specified and directed by Engr-in-charge.

M&L in replacement of old unserviceable sub main wiring using 4 runs of 4 sq mm FRLS, IS 694 PVC insulated copper conductor 1100 Volts grade conforming to IS specification drawn through and including PVC conduit of suitable size not less than 25mm dia medium grade surface on wall along with 1 run of 4 sq mm PVC insulated copper conductor FRLS cable as earth lead connected to common earth dolly and including taking down old unserviceable wiring and making good the existing disturbed surface using wall putty and matching colour emulsion paint complete all as specified and directed by Engr-in-charge.

All as per item No.118 above but in PVC casing and capping of suitable size complete all as specified and directed by Engr-in-charge. Note for item No.116 to 119:- (i) Necessary PVC rigid junction boxes for identifying junction as required on site/directed by Engineer in charge for point wiring work with PVC dummy plates shall deemed to be included in the quoted rate. (ii) One run of PVC conduit/casing and capping along with 5 runs of respective size of PVC insulated copper conductor cable will be measured as one unit. (iii) Strictly follow the proper colour code red/yellow/blue for phase, black for neutral and green for earth.

M&L in replacement of old unserviceable sub main wiring using 2 runs of 10 sq mm FRLS, IS 694 PVC insulated copper conductor 1100 Volts grade conforming to IS specification drawn through and including PVC conduit of suitable size not less than 20mm dia medium grade surface on wall along with 1 run of 10 sq mm PVC insulated copper conductor FRLS cable as earth lead connected to common earth dolly and including taking down old unserviceable wiring and making good the existing disturbed surface using wall putty and matching colour emulsion paint complete all as specified and directed by Engr-in-charge.

All as per item No.120 above but in PVC casing and capping of suitable size complete all as specified and directed by Engr-in-charge.

M&L in replacement of old unserviceable sub main wiring using 2 runs of 6 sq mm FRLS, IS 694 PVC insulated copper conductor 1100 Volts grade conforming to IS specification drawn through and including PVC conduit of suitable size not less than 20mm dia medium grade surface on wall along with 1 run of 6 sq mm PVC insulated copper conductor FRLS cable as earth lead connected to common earth dolly including making good the existing disturbed surface using wall putty and matching colour emulsion paint complete all as specified and directed by Engr-in-charge.

All as per item No.122 above but in PVC casing and capping of suitable size complete all as specified and directed by Engr-in-charge.

M&L in replacement of old unserviceable sub main wiring using 2 runs of 4 sq mm FRLS, IS 694 PVC insulated copper conductor 1100 Volts grade conforming to IS specification drawn through and including PVC conduit of suitable size not less than 20mm dia medium grade surface on wall along with 1 run of 4 sq mm PVC insulated copper conductor FRLS cable as earth lead connected to common earth dolly including taking down old unserviceable wiring and making good the existing disturbed surface using wall putty and matching colour emulsion paint complete all as specified and directed by Engr-in-charge.

All as per item No.124 above but in PVC casing and capping of suitable size complete all as specified and directed by Engr-in-charge.

M&L in replacement of old unserviceable sub main wiring using 2 runs of 2.5 sq mm FRLS, IS 694 PVC insulated copper conductor 1100 Volts grade conforming to IS specification drawn through and including PVC conduit of suitable size not less than 20mm dia medium grade surface on wall along with 1 run of 2.5sq mm PVC insulated copper conductor FRLS cable as earth lead connected to common earth dolly including taking down old unserviceable wiring and making good the existing disturbed surface using wall putty and matching colour emulsion paint complete all as specified and directed by Engr-in-charge.

All as per item No.126 above but in PVC casing and capping of suitable size complete all as specified and directed by Engr-in-charge. Note for item No.120 to 127:- (i) Necessary PVC rigid junction boxes for identifying junction as required on site/directed by Engineer in charge for point wiring work with PVC dummy plates shall deemed to be included in the quoted rate. (ii) One run of PVC conduit/casing and capping along with 3 runs of respective size of PVC insulated copper conductor cable will be measured as one unit. (iii) Strictly follow the proper colour code red/yellow/blue for phase, black for neutral and green for earth.

S&F in replacement of old unserviceable wall mounted 10 W 2 ft LED batten, out put lumen ≥ 100 lumen/watts, CCT ≥5500k, efficacy 100 lumen per watt, life 50,000 burning hrs, aluminum body, surge protection 4kV, power factor > 0.95, THD ≤10%, extruded channel in thermally conductive material for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver making connection to ceiling rose to fitting with 3 core 1 sqmm copper conductor complete all as specified and directed by Engineer-in charge. Make:- Crompton model No. CCS-103-10-65-SL-DP-NWH or equivalent in Philips/ Wipro/Havells/Bajaj.

All as per item No.128 above but warm white, CCT ≥3000k complete all as specified and directed by Engineer-in charge. Make:- Crompton model No. CCS-103-10-65-SL-DP-NWH or equivalent in Philips/ Wipro/Havells/Bajaj.

S&F in replacement of old unserviceable wall mounted 20 W LED 4ft white batten out put lumen ≥ 110 lumen/watts, efficacy 100 lumen per watt, CRI > 80, CCT >5500k , internal surge protection up to 4kV , power factor ≥ 0.95 having extruded aluminium housing provided for efficient heat dissipation with poly carbonate diffuser and integrated electronic driver with all accessories pre-wired and including connecting up 3 core flexible copper conductor cable suitable size from fitting to ceiling rose/connection terminals complete all as specified and directed by Engineer in charge. Make:- Crompton model No. CCS-103-20-65-SL-DP-NWH or equivalent in Philips/ Wipro/Havells/Bajaj Note:- LM79 report accredited by NABL certified lab should be submitted.

All as per item No.130 above but warm white, CCT ≥3000k complete all as specified and directed by Engineer in charge. Make:- Crompton model No. CCS-103-20-65-SL-DP-WW or equivalent in Philips/ Wipro/Havells/Bajaj.

S&F in replacement of suspended luminaries 36W LED 4 feet with colour temperature 5500K having extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver including 02 Nos suspension kit, CRI ≥ 80,THD ≤ 10 %, Efficacy ≥100 lm/W, powerfactor ≥ 0.95, internal surge voltage- 2kv, complete with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size from fitting to ceiling rose/connection terminals complete all as specified and directed by Engineer-in-Charge. Make:- Crompton LCLP54-36-CDL or equivalent in Philips/Wipro/ Havells/Bajaj.

S&F in replacement 9W LED spot light ideal for wardrobes, furniture lighting, displays & interior decorations etc, luminous efficacy ≥ 100/w, CCT ≥ 5500 k,CRI ≥ 80, THD ≤ 10 ,PF .0.95 including connecting up 3 core copper conductor cable of suitable size from fitting to ceiling rose/connection terminals complete all as specified and directed by Engineer in charge. Make:- Crompton CDR-211-09-30-SL-NWH or equivalent in Philips/Wipro/Havells/ Bajaj.

S&F in replacement LED flat downlighter 18W white in round profile luminous efficacy ≥ 100/w, CCT ≥ 5500 k,CRI ≥ 80, THD ≤ 10 ,PF .0.95 including connecting up 3 core 1 sqmm copper conductor cable from fitting to ceiling rose/connection terminals complete all as specified and directed by Engineer in charge. Make:- Crompton LSCRM-18W-CDL or equivalent in Philips/ Wipro/Havells/Bajaj.

All as per item No.134 above but warm white, CCT ≥ 3000k complete all as specified and directed by Engineer in charge. Make:- Crompton LSCRM-18W-WW or equivalent in Philips/ Wipro/Havells/Bajaj.

S&F in replacement LED flat downlighter 15W white in round profile luminous efficacy ≥ 100/w, CCT ≥ 5500 k,CRI ≥ 80, THD ≤ 10 ,PF .0.95 including connecting up 3 core 1 sqmm copper conductor cable from fitting to ceiling rose/connection terminals complete all as specified and directed by Engineer in charge. Make:- Crompton LSCRM-15W-CDL or equivalent in Philips/ Wipro/Havells/Bajaj.

All as per item No.136 above but warm white, CCT ≥ 3000k complete all as specified and directed by Engineer in charge. Make:- Crompton LSCRM-15W-WW or equivalent in Philips/ Wipro/Havells/Bajaj.

S&F in replacement LED flat downlighter 12W white in round profile luminous efficacy ≥ 100/w, CCT ≥ 5500 k,CRI ≥ 80, THD ≤ 10 ,PF .0.95 including connecting up 3 core 1 sqmm copper conductor cable from fitting to ceiling rose/connection terminals complete all as specified and directed by Engineer in charge. Make:- Crompton LSCRM-12W-CDL or equivalent in Philips/ Wipro/Havells/Bajaj.

All as per item No.138 above but warm white, CCT ≥ 3000k complete all as specified and directed by Engineer in charge. Make:- Crompton LSCRM-12W-WW or equivalent in Philips/ Wipro/Havells/Bajaj.

S&F in replacement square recess mounted LED edge lit slim downlight with diecast aluminium housing finished in premium white powder coating 6W white luminous efficacy ≥ 100/w, CCT ≥ 5500 k,CRI ≥ 80, THD ≤ 10 ,PF .0.95 including connecting up 3 core 1 sqmm copper conductor cable from fitting to ceiling rose/connection terminals complete all as specified and directed by Engineer in charge. Make:- Crompton LSCSM-6W-CDL or equivalent in Philips/ Wipro/ Havells/Bajaj.

All as per item No.140 above but warm white, CCT ≥ 3000k complete all as specified and directed by Engineer in charge. Make:- Crompton LSCSM-6W-WW or equivalent in Philips/Wipro/ Havells/Bajaj.

S&F in replacement square recess mounted LED edge lit slim downlight with diecast aluminium housing finished in premium white powder coating 12W white luminous efficacy ≥ 100/w, CCT ≥ 5500 k,CRI ≥ 80, THD ≤ 10 ,PF .0.95 including connecting up 3 core 1 sqmm copper conductor cable from fitting to ceiling rose/connection terminals complete all as specified and directed by Engineer in charge. Make:- Crompton LSCSM-12W-CDL or equivalent in Philips/ Wipro/Havells/Bajaj. Note:- LM79 report accredited by NABL certified lab should be submitted.

All as per item No.142 above but warm white, CCT ≥ 3000k complete all as specified and directed by Engineer in charge. Make:- Crompton LSCSM-12W-WW or equivalent in Philips/ Wipro/Havells/Bajaj.

S&F in replacement slim design LED 9W white recessed square polycarbonate housing down lighter with superior luminous efficacy ≥ 100/w, CCT ≥ 5500 k,CRI ≥ 80, THD ≤ 10 ,PF .0.95 including connecting up 3 core 1 sqmm copper conductor cable from fitting to ceiling rose/connection terminals complete all as specified and directed by Engineer in charge. Make:- Crompton LSDEP-09-CDL or equivalent in Philips/Wipro/ Havells/Bajaj.

All as per item No.144 above but warm white, CCT ≥ 3000k complete all as specified and directed by Engineer in charge. Make:- Crompton LSDEP-09-WW or equivalent in Philips/Wipro/ Havells/Bajaj.

S&F in replacement slim design LED 9W white recessed round polycarbonate housing down lighter with superior luminous efficacy ≥ 100/w, CCT ≥ 5500 k,CRI ≥ 80, THD ≤ 10, PF .0.95 including connecting up 3 core 1 sqmm copper conductor cable from fitting to ceiling rose/connection terminals complete all as specified and directed by Engineer in charge. Make:- Crompton LCDEP-09-CDL or equivalent in Philips/Wipro/ Havells/Bajaj.

All as per item No.146 above but warm white, CCT ≥ 3000k complete all as specified and directed by Engineer in charge. Make:- Crompton LCDEP-09-WW or equivalent in Philips/Wipro/ Havells/Bajaj.

S&F in replacement LED Downlighter 30W with Luminous efficacy-> 100/watt, CCT> 5500 k,CRI- 80,Power factor >0. 95 deep recessed antiglare led downlight for general and accent lighting with premium white reflector matches the ceiling and accentuates the architecture of the area without compromising the light output including driver and all connected accessories with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size from fitting to ceiling rose/connection terminals and adjusting rings for fixing etc. complete all as specified and directed by Engineer in charge. Make:- Crompton Cat No. CDR-216-30-30-SL-NWH or equivalent in Philips/Wipro/ Havells/Bajaj. Note:- LM79 report accredited by NABL certified lab should be submitted.

S&F in replacement 10 W white/warm white environmental friendly, ultra modern, energy saving, surface mounted, decorative bulk head edge-lit LED luminaire out put lumen ≥ 100 lumen/watts, efficacy ≥ 100 lm/W, life 50,000 burning hrs, aluminum body, surge protection 4kV, power factor ≥ 0.98, THD ≤ 10%, making connection to ceiling rose to fitting with 3 core 1 sqmm copper conductor complete all as specified and directed by Engineer-in charge. Make:- Jaquar model No. LBLK02X010XN or equivalent in Crompton/Bajaj/Havells.

S&F in replacement recess full lit luminaire with glare free uniform illumination with longer life and less maintenance 36 W (2 ' x 2 ') in MS housing with opal diffuser with output lumen ≥ 110 lumen/ watts, luminous efficacy ≥ 100/watt, CCT > 5500 k,CRI ≥ 80,Power factor ≥ 0. 95,THD ≤ 10 with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size from fitting to ceiling rose/ connection terminals including aluminium frame for fitting the same complete all as specified and directed by Engineer in charge. Make:- Crompton LCTLRNE-36-FO-CDL or equivalent in Philips/Wipro/Havells/ Bajaj. Note:- LM79 report accredited by NABL certified lab should be submitted.

S&F in replacement surface full lit luminaire with glare free uniform illumination with longer life and less maintenance 36 W (2 ' x 2 ') in MS housing with opal diffuser with colour temp 6000K, output lumen >110 lumen/watts, luminous efficacy-> 100/watt, CCT > 5500 k,CRI ≥ 80,Power factor ≥ 0. 95,THD ≤ 10 with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size from fitting to ceiling rose/ connection terminals including aluminium frame for fitting the same complete all as specified and directed by Engineer in charge. Make:- Crompton LCTLSNE-36-FO-CDL or equivalent in Philips/ Wipro/Havells/ Bajaj.

S&F in replacement high efficacy 1x1 LED 18 watt surface full lit luminaire with glare free unifrom illumination with longer life and less maintenance and including connecting up with three core twisted flexible copper conductor cable with suitable size from fitting to ceiling rose/connection terminals, luminous efficacy ≥ 100/w, CCT ≥ 5500 k,CRI ≥ 80, THD ≤ 10 ,PF .0.95 all connected accessories with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size from fitting to ceiling rose/connection terminals and adjusting rings for fixing etc. complete all as specified and directed by Engineer in charge. Make:- Crompton LCTLSNE-18-FO-CDL or equivalent in Philips/ Wipro/Havells/ Bajaj. Note:- LM79 report accredited by NABL certified lab should be submitted.

All as per item No.152 above but recess type complete all as specified and directed by Engineer in charge. Make:- Crompton LCTLRNE-18-FO-CDL or equivalent in Philips/ Wipro/Havells/ Bajaj.

Taking down carefully copper/ aluminium point wiring (light, fan and power socket etc) complete including fittings such as switches, ceiling roses, pendent, regulators, sockets, MCB/ MCCB/ MCB DB/ earth plug and socket etc and making good matching to the existing colour to the disturbed surface complete all as specified and directed by Engineer in charge.

M&L for color code point wiring FRLS PVC insulated and unsheathed cable with 1.5 sqmm copper conductor single core multistandred 1100 volt grade conforming to IS 694 drawn through PVC conduit of suitable size, concealed / semi concealed/open suitable size modular metal flush box fitted with modular cover plate with frame (inner/ outer plate) for mounting switches or sockets, regulators etc including FRLS 1.5 sqmm earth wire copper insulated wire connected to common earth dolly complete all as specified for the following:- Notes:- (i) Necessary PVC rigid junction boxes for identifying junction as required on site/directed by Engineer in charge for point wiring work with PVC dummy plates shall deemed to be included in the quoted rate. (ii) Same size wire shall be used for phase, neutral and earth conductor. (iii) The wiring shall be done strictly by following proper colour coding using red , blue, yellow for phase, black for neutral and green for earth leads. (iv) Size of copper earth wire must be equal to size of current carrying conductor upto size 16 sqmm.

(a) One light/ fan point controlled by one switch

(b) One 3 pin socket outlet 5 Amps on the same board with other switches

(c) 5 Amps socket point on independent board

M&L for color code point wiring FRLS PVC insulated and unsheathed cable with 1.5 sqmm copper conductor single core multistandred 1100 volt grade conforming to IS 694 drawn through PVC casing and caping suitable size modular metal flush box/PVC box fitted with modular cover plate with frame (inner/ outer plate) for mounting switches,sockets,regulators etc including FRLS 1.5 sqmm earth wire copper insulated connected to common earth dolly complete all as specified for the following:-

(a) One Light/ fan point controlled by one switch

(b) One 3 pin socket outlet 5 Amps on the same board with other switches

(c) 5 Amps socket point on independent board

All as per item No.155 here in above but 2.5 sqmm for 6/16 Amps socket on independent board complete all as specified and directed by Engineer in charge.

All as per item No.156 here in above but 2.5 sqmm for 6/16 Amps socket on independent board complete all as specified and directed by Engineer in charge.

S&F in replacement modular switch 1 way 6 Amps 1 module suitable for fixing existing cover plate complete all as specified and directed by Engineer in charge.

S&F in replacement modular switch 1 way 16 Amps 1 module suitable for fixing existing cover plate complete all as specified and directed by Engineer in charge.

S&F in replacement modular socket 6 Amps 2/3 pin combined 2 module suitable for fixing existing cover plate complete all as specified and directed by Engineer in charge.

S&F in replacement modular socket 6/16 Amps 2/3 pin combined 2 module suitable for fixing existing cover plate complete all as specified and directed by Engineer in charge.

S&F in replacement switch socket combination 5 pin, 6/16 Amp ISI Marked with PVC box complete all as specified and directed by Engineer in charge.

S&F in replacement switch socket combination 5 pin, 6 Amp ISI Marked with PVC box complete all as specified and directed by Engineer in charge.

S&F in replacement modular fan step regulator 120W, electronic 2 Module step up type AC 230 Volts complete all as specified and directed by Engineer in charge.

S&F in replacement lamp holder, PVC/Polycarbonate type with back plate suitable for batten/bracket fittings complete all as specified and directed by Engineer in charge.

S&F in replacement single pole and neutral enclosure with two pin and plug and socket complete with one single pole MCB, AC 240 Volts, 20 Amps including making good the existing disturbed surface using wall putty and matching colour emulsion paint complete all as specified and directed by Engineer in charge.

S&F in replacement MCB protected socket PVC plastic base model with one single pole MCB, AC 240 Volts, 20 Amps including making good the existing disturbed surface using wall putty and matching colour emulsion paint complete all as specified and directed by Engineer in charge.

S&F in replacement triple pole and earth enclosure with a three pin and earth plug with socket complete with one triple pole MCB 32 Amp including making good the existing disturbed surface using wall putty and matching colour emulsion paint complete all as specified and directed by Engineer in charge.

S&F in replacement modular white cover plate with frame 1 module complete all as specified and directed by Engineer in charge.

All as per item No.170 above but 2 module complete all as specified and directed by Engineer in charge.

All as per item No.170 above but 3 module complete all as specified and directed by Engineer in charge.

All as per item No.170 above but 4 module complete all as specified and directed by Engineer in charge.

All as per item No.170 above but 6 module complete all as specified and directed by Engineer in charge.

All as per item No.170 above but 8 module complete all as specified and directed by Engineer in charge.

All as per item No.170 above but 12/18 module complete all as specified and directed by Engineer in charge.

S&F in replacement modular box suitable for fixing 1/2 module complete all as specified and directed by Engineer in charge. Note:- The rate quoted for replacing of modular box is deemed to be inclusive of necessary cement/putty work and finishing work of white wash /colour wash for matching with existing surface.

All as per item No.177 above but 3 module complete all as specified and directed by Engineer in charge.

All as per item No.177 above but 4 module complete all as specified and directed by Engineer in charge.

All as per item No.177 above but 6 module complete all as specified and directed by Engineer in charge.

All as per item No.177 above but 8/12 module complete all as specified and directed by Engineer in charge.

S&F in replacement of old unserviceable MCB DB SPN 240V double door outdoor type with bush bar of appropriate current carrying capacity, neutral link, earth bar and din rail including making good the existing disturbed surface using wall putty and matching colour emulsion paint complete all as specified and directed by Engineer-in-Charge for the following:-

S&F in replacement MCB DB TPN 415V double door type with bus bar of appropriate current carrying capacity, neutral link, earth bar and din rail suitable for fixing existing space and model vertical or horizonal including making good the existing disturbed surface using wall putty and matching colour emulsion paint complete all as specified and directed by Engineer-in-Charge for the following:-

S&F in replacement MCB single pole AC 240 Volts, C series 50 Hz 10 kA breaking capacity, 6 to32 Amps complete all as specified and directed by Engineer in charge.

S&F in replacement MCB SPN AC 240 Volts, 50 Hz ,C series 10 kA breaking capacity 25/32 Amps complete all as specified and directed by Engineer in charge.

S&F in replacement of old unserviceable MCB single pole & neutral AC 240 Volts, 50 Hz , C series 10 kA breaking capacity, 40 Amps complete all as specified and directed by Engineer in charge.

S&F in replacement of old unserviceable MCB triple pole & neutral AC 415 Volts, 50 Hz , C series 10 kA breaking capacity, 25/32 Amps complete all as specified and directed by Engineer in charge.

S&F in replacement of old unserviceable MCB triple pole & neutral AC 415 Volts, 50 Hz , C series 10 kA breaking capacity, 40-63 Amps complete all as specified and directed by Engineer in charge.

S&F in replacement of old unserviceable capacitors 4 mfd, AC 230 Volts suitable for exhaust fan complete all as specified and directed by Engineer in charge.

S&F in replacement of old unserviceable capacitors 2.5mfd, AC 230 Volts suitable for celling fan/exhaust fan complete all as specified and directed by Engineer in charge.

Dismantling ceiling fan of 1200 mm sweep of any make and model, removing the defective burnt windings, rewinding the same with appropriate gauges of super enamelled copper winding wire including varnishing, drying and re assembling, re fixing, making electrical connection etc complete in all respect all as directed.

Dismantling exhaust fan of 300/450 mm sweep / wall mounted fan of any make and model, removing the defective burnt windings, rewinding the same with super enamelled copper winding wire of appropriate gauge including varnishing, drying and re assembling, re fixing, making electrical connection etc complete in all respect all as directed.

S&F in replacement of old unserviceable MCCB four pole 100 Amps 16/18 kA 415 Volts, 50 Hz suitable for existing busbar complete all as specified and directed by Engineer in charge.

Disconnect electric connections and taking down carefully unserviceable ceiling light/ highbay light fittings of different capacities at Nalanda Main Bldg /Aryabhatta/ Bhaskara/Panini Library by opening cover and body for repair/ replacement of electrical items and refixing the same or fixing only new items /fittings including connecting/ testing complete all as specified and directed by Engineer in charge. Note:- Fitting are fitted at 16 to 20 mtr height.The contractor shall arrange ladder/ scaffolding of required height at his own arrangement.The rates quoted are deemed to be inclusive for the above provision.

M&L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground, earth pit not less than 2.25 metre deep below ground level, connected to 25x4 mm size galvanized iron strip as earthing strip by means of bolts, nuts, check nuts, and washers of galvanized iron or steel all as shown in electric plate No 3 of SSR Part I connected to earthing test point all as specified or indicated including provn of necessary excavation and earthwork in any type of soil, PCC pit, RCC cover and 20 mm bore medium grade watering pipe, water funnel with GI wire mesh, 40 mm bore medium grade protection pipe, common salt, charcoal dust, returning filling in of soil, removal of spoil to a distance not exceeding 50 mtr etc including testing on completion all as specified & taking down old unserviceable earthing complete all as specified and directed by Engineer-in charge.

M&L for earth continuity conductor or main earthing lead fixed to wall on epoxy /OMC insulators or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required for 25 x4 mm galvanised iron strip including taking down old GI strip complete all as specified and directed by Engineer-in charge.

All as per item No.196 above but copper strip 20x3 mm size complete all as specified and directed by Engineer-in charge.

S&F in replacement of old unserviceable LED linear batten with smart sensor, inbuilt sensor based smart LED auto dimmable batten, made from industrial Engineering grade extruded polymer housing, opaque glare free diffuser, pre wired with all accessories complete all as specified and directed by Engineer-in charge. Make:- Crompton/ Havells/ Shakti/Wipro/Philips.

General Engineering and Constructions

SANDR

Gates Infra Construction Co