ADDITIONAL/ ALTERATION OF BLDG NO. T-411 AT 26 RAJPUT AND PROVN OF 01 X KOTE (NEAR 26 RAJPUT QG) AND 01 X AMOURER SHOP AND STORE FOR 166 MTN BDE CAMP IN HASIMARA MIL STATION UNDER GE (SOUTH) BINNAGURI

Amount

Schedule 'A'

Surface excavation not exceeding 30 cm deep and averaging15 cm deep and getting out in any type of soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for foundation etc or for shafts, wells cesspits manholes pier holes etc not exceeding 10 sqm on plan and not exceeding 1.5 m depth in soft /loose soil etc complete all as specified and directed

Removal of excavated materials not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting points etc complete all as specified and directed

Returning, filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in any type of soil etc complete all as specified and directed

Excavation in soft / loose soil for post holes (or similar holes) each not exceeding 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and directed.

Cement concrete Type B2 1:2:4 (40mm graded aggregate) in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as per Specified and directed by Engr In Charge

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for RCC (nominal mix) 1:1.5:3 type B0 using 12.5 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed . Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (nominal mix) 1:1.5:3 type B0 using 12.5 mm graded stone aggregates as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

Form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves, for flat fair finished concrete surfaces complete all as specified and directed.

M&L for (nominal mix)1:1.5:3 type B0 using 12.5 mm graded stone aggregates as in chajjas and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

Form work to chullah hood, chajjas, troughs and similar items including edges etc for fair finished flat concrete surface complete all as specified and directed.

M&L Brick work using Fly Ash bricks with sub class 'B' bricks curved on plan with mean radius not exc 6m with bricks roughly cut to radius or bricks with wedge shaped joints built in cement mortar 1:6 complete all as specified and directed.

M&L Brick work using Fly Ash Bricks with sub class'B' bricks curved on plan with mean radius half bricks roughly cut to radius or bricks with wedges shaped joints built in cement mortar 1:6 complete all as specified and directed.

Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild Steel TMT bar 6 to 8 mm dia cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild Steel TMT bar 5mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:4 on fair faces of brick or concrete surface of wall and finished even and smooth with out using extra cement complete all as specified and directed.

M&L for external rendering 20 mm thick in two layer, first layer shall be of 10 mm thick CM 1:6 and second layer of finishing coat shall be 10 mm thick in CM 1:4 mixed with WPC @3% by weight of cement on brick work or concrete surfaces of wall and finished even and fair complete all as specified and directed. Note-WPC shall be measured and paid seperately.

Supply only integral water proofing compound all as specified and directed.

M&L for sand filling under floor or in foundations including watering and consolidation complete all as specified and directed

M&L Broken stone or boulders hardcore of gauge exceeding 63 mm but not exceeding 100 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in floor finishes 40 mm thick laid in panels & finished even and smooth without using extra cement complete all as specified and directed. Note- Glass dividing strips shall be measured & paid separately as supply only.

M&L for Machine cut kota stone slab flooring mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and 15 mm thick screed bed or bedding layer in CM 1:4 surface finished fair and even for laying floor finishescomplete all as specified and directed.

M&L for Machine cut kota stone in riser of steps, skirting, dado and pillar mirror finished 20-25 mm thick over cement base rendering laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed. complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in vertical surface /skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in CM 1:6 surface finished fair and even for laying floor finishes complete all as specified and directed.

M&L for glazed ceramic coloured tiles 450 x 350 x 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 and painted one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and directed.

S&F MS steel Hollow section Square/rectangular as in roof truss ,purlin,rail etc etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 and painted one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and directed.

S&F rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes ,without and attachment of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S&F Mild steel bolts. purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30cm long

S&F Rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding/ eaves board fixed with selp tapping screw complete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding/eaves board fixed with selp tapping screw complete all as specified and directed.

M&L for non Asbestos ,fibre reinforced standard cement board as in celiling ,4mm thick designer board (610mm x 610mm ) complete all as specified and as directed

S&F Anodised aluminium snap grid frame work for false ceiling all as specified and as directed

M&L for applying two coats of acrylic distemper on newly plastered wall surface including preparation of surface over a coat of 1mm thick Birla wall care putty complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and apply three coat of white wash complete all as specified and directed.

Material and Labour for preparation of new plastered surfaces and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

S&F pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of priming complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded aggregate) as in hold fast block including necessary form work etc complete all as specified and as directed.

S&F 35 mm thick second class hard wood rail and style plain framed factory made panelled shutter (two panel) with lock rail and panel of 9 mm BWP commerical ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L Second class hard wood 30 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.20 (a) complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F mild steel barrel tower bolts stove enamelled black with bright bolt 150 mm long complete all as specified and directed.

S&F mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate of 250 mm length of bolt complete all as specified and directed.

S&F aluminium handles cast type anodised of 150 mm size complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and directed

S&F steel Door with side hung shutters including projecting type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F 1.25 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc as required complete all as specified and directed.

S&F collapsible steel gate, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc, erected in position and securing runners with holdfasts and brackets complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate, 75mm thick in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

S&F Powder coated anodised aluminium window sliding type three track aluminium sections weighing not less than 0.55 Kg per mtr (Two glazed shutter & one wire mess shutter) including necessary jointing cleats, glazing cleats, rubber packing anodised aluminium snap gridding, screws, handle, locking arrangement etc complete and 5.5 mm thick plain or tinted glass complete all as specified. (Make : Jindal/Hindalco/Indal).

S & F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as shown on drawing in section 8 of SSR-2010 Part-II complete all as specified and directed

S & F for solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2010 Part-II complete all as specified and directed

S&F Butt hinges, medium weight, cold rolled mild steel 75 mm long complete all as specified and directed.

S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 150 mm length of bolt complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section 100 mm long complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate, 75mm thick in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

M&L for RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate as in slab supported on wall,beam and column in floors, roofs, landings, balconies, canopies and in shelves and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) for fair finished flat surface of concrete complete all as specified and directed

M&L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for preparation of old surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 15 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 20 mm bore of pipe complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore of pipe etc complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore of pipe etc complete all as specified and directed.

S&F PVC (SWR) bends any radius of 75 mm bore with out access door complete all as specified and directed.

S&F PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe with access door complete all as specified and directed

S&F PVC (SWR) bends any radius of 110 mm bore complete all as specified and directed.

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F Water closet vitreous china squatting pan, orissa pattern 580x440mm white with integral foot rests excluding flushing cistern and flush pipe including provision of lime concrete bedding complete all as specified and directed.

S&F wash hand basin vitreous China, white, flat back (550x400mm) including cutting for and pinning ends of brackets and waste coupling of Bass CP for basin etc with long screwed shanks and fly nuts, full threaded flage embedded in white cement incl PVC waste pipe required length complete all as specified and directed.

S&F PVC 10 litres capacity valveless ,syphonic action type low level flushing cistern ,white including flush pipe, cantilever brackets ,inlet, ball valve, float and handle, etc complete all as specified and directed.

S & F 15mm size PVC Connection with PTMT nut of length 450mm , complete all as specified and as directed.

S&F for 15mm bore dia of pipe pillar taps cast copper alloy, with capstan head chromium plated screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F Stop valves cast copper alloy, screwed down, high pressure with crutch or butterfly handle chromium plated fancy type screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe complete all as specified and directed.

S&F Stop valves cast copper alloy, screwed down, high pressure with crutch or butterfly handle chromium plated fancy type screwed both ends for iron pipe or for unions for 20 mm bore dia of pipe complete all as specified and directed.

S&F bib taps cast copper alloy with crutch or butterfly handle fancy type, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore dia of pipe complete all as specified and directed.

M&L for Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:4 complete all as specified and directed.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.2 M dia X 1.5 M effective depth Complete all as specified and as directed

Taking down carefully aluminium point wiring for one light, socket or power etc incl all fittings such as switches sockets, holders, light fittings, fan regulators etc and making good the disturbed surface of wall ceiling complete.

M&L for concealed point wiring contrilled by one switch with 1.50 Sqmm (nominal area) FRLS, PVC insulated 1100 volts grade multi stranded copper conductor single core unsheathed cable and FRLSm ISI marked, PVC insulated 1100 volts grade multi stranded copper conductor single core of size 1.50 Sqmm as earth continuity conductor connected to common earth dolly, drawn through in and including rigid PVC conduit (Medium Grade) of suitable size, with all fittings, ISI marked and accessories, the pipe shall be fixed with clamping and shadle inculding provision of mild steel terminal boxes/ Sunken boxes of suitable sixe made with 1.6mm thick mild steel sheet recessed in wall with a coat of black bituminus paint and providing of with 3mm thick bakellite/ PVC sheet ISI markes tipo cover, suitable for fixing of switches/ sockets/ regulators etc fixed in recess of wall with brass chrominum plated screws and cap washer complete all as specirfied and directed for the following: 91.01 One light point controlled by one way switch 5/6 amps

One ceiling fan/ exhaust fan point controlled by one way switch 5/6 amps

One socket out let 5/6 amps point of the same board

One socket out let 5/6 amps point on the independent board

All as per item No. 91 of above but wiring with 2.5 Sqmm single core copper conductor for one socket out let 15/16 amps point on the independent board

S&F socket 2 in 1, 5 pin, 5/6 Amps, white ivory finish flash tupe complete all as sepecified and directed

S&F of socket outlet 2 in 1, 5 pin 5/15 Amp multipurpose 230 volts flush type complete all as specified and directed by Engr-in- charge

S&F of switch piano flush type 5/6 amps single pole one way all as specified. Make: Anchor Penta/ Havelles Reo

S&F of switch piano flush type 15/16 amps single pole one way complete all as specifiedand as directed

S&F of ceiling rose, bakellite, surface type, 220/240 volts, three terminals complete all as specified and as directed.

M&L for lamp holder, insulated body, with badk plate suitable for batten/ angle fittings complete all as specified and directed.

S&F in replacement of LED lamp 9/10 W B22 retrofit type all as spcefied

S&F wall mounted slim LED batten 18W, with extruded aluminium housing, with integrated LED driver complete all as specfied and as directed. Make: Crompton, Cat No. LCTL-18-CDL or equivalent Make of Bajaj, Surya, C&S

S&F of LED street light fittings 45 watt in aluminium PDC housing, toughed glass cover with IP66 protection complete all as specified and as directed. (Make: Crompton, Cat No. LSTS-45-CDL or equivalent of Bajaj/ Surya)

M&L for sub main wiring with 3 run of 4.00 Sqmm (nominal cross- sectional area) PVC insulated unsheathed single core cable of working voltage 1100 votls grade with stranded cipper conductor drawn in PVC rigid non- metalic conduit complete all as specified and as directed. Note : (i) Three run of sub main wiring cable alongwith 25 PVC conduit pipe shall be measured as one unit length.

S&F sheet metal enclosure for 8way Distribution Boards (DBs), double door, single pole and neutral with 200 amps rated bus bar, IP-43 protection suitable for fixing MCB's/ Isolators with and onc blanking plated complete all as specified and as directed.

S&F of MCB, single pole and neutral 40 Amps, 240 volts, 'C' curve, 10 KA all complete as specified and as directed

S&F MCB, single pole, 5 to 32 amps, 240 votls, 'C' curve, 10 KA all complete as specified and as directed. Make : Havells DHMGBDPF06-32 or equivalent make.

M&L for street light bracket made out of GI pipe light grade 25mm dia 1.2 mtr length bent to shjape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat ironof size 25x5 mm suitable length 2 Nos comnplete with drilling, hole fixing with nuts bolts and washers including painted with two coats aluminium paint over a coat or red oxide primer.

M&L in replacement for earthing complete with glavanised steel plate electrode of size 600x600x6.30 mm thick burried directly I ground with earth pit not less than 2.25 meter deep belownormal ground level with top edge of plate not less than 1.5 meter below ground level connected to galvanised 4 mm dia earth lead by means of nuts bolts check nut GI washers earth wire protected by galvanised iron pipe 15mm bore (light grade) for building LT wall panel all as directed including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8mm diameter MS bar finnel wire mesh 20mm bore galvanised iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soil with and inckluding taking down the old one complete all as shown in electrical plate No.3 of SSR Part-I 2009 including testing on completion all as specified and directed. Note: The Rate for Taking down the old uncv Earthing shall be deemed to be included in the unit rate.

Supply and fixing ceiling fans complete with blades, downs rods, electronics regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S&F fan exhaust 380mm sweep, single phase heavy duty with their all accessories fixed properly on stone masonary wall surface with provisioning rag bolts, nuts, washers etc including making circular exhaust hile of 300mm dia, lauver shutter suitable for the same exhaust fan and which shall easiily be operated with exhaust aire pressure, any disturbed surface to wall shall be made good by cement work/ plastering and matching by existing colour white/ colour wash and allmetal parts of this item of work shall be painted with two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer as well as writing the MES No with white colour paint including connecting/ testing complete as directed. Make : Khaitan/USHA/ Havells

M/S. VINITA CONSTRUCTION

SHRI SURAJIT SIKDER

M/S MANODEEP CONSTRUCTION

M/S. NARENDRA KUMAR GARG