KOTTIYOOR TEMPLE-TOURISM EXPERIENCE STREET OF THALASSERY HERITAGE PROJECT, KANNUR DISTRICT

Amount

GALLERY AND HERITAGE KNOWLEDGE CENTRE AND PATHWAY

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position Cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size).Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete. (Centering and shuttering for different category of work may be considered separately.)

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo - Mechanically Treated bars of grade Fe-500D or more. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference. Testing strength and quality of steel in Govt labs as per IS.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level. The Compressive strength of concrete has to be tested in Govt labs as per IS.

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level. The Compressive strength of concrete has to be tested in Govt labs as per IS.

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work. Make: Asian, Berger, Nerolac or eq. in the order of pref.

50.6.7.2 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

od249158/2019_2020 : Exposed Laterite masonry in CM 1:6 (1 cement : 6 course sand) for superstructure above plinth level up to floor two level with neatly dressed best quality laterite stones of size 30x20x20 cm.including all cost of materials, labour charges, conveyance, curing etc. complete as per standard specification.

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes. Make: TATA, JSW, VIZAG, SAIL or eq.

12.48 : Providing & fixing on Roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately) including prior sample approval and direction of Engineer at site.

12.49 : Providing & laying on Roof pressed clay tile ridge (Mangalore tile) of 20 mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately ). including prior sample approval and direction of Engineer at site.

od249299/2019_2020 : Providing & fixing on Roof pressed clay ceiling tiles 30x25mm size of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately). including prior sample approval and direction of Engineer at site.

50.9.2.1 : Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge.using Anjili/ Jack wood

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

50.13.1 : 9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

50.9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality second class teak wood /jack wood

9.5.1.1 : Providing and fixing panelled or panelled and glazed shutters for shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer - in-charge.Second class teak wood35 mm thick shutters

9.7.1 : Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:Second class teak wood

od250948/2019_2020 : Providing and fixing 8" or nearest size punit antique tower bolt including all cost and labour charges (Brass Heavy duty )

od250949/2019_2020 : Providing and fixing 4" or nearest size punit antique tower bolt antique including all cost and labour charges (Brass Heavy duty )

od250950/2019_2020 : Providing and fixing 4" SS punit hinges antique ( approved by the engineer)including all cost and labour charges.(Heavy duty )

od250951/2019_2020 : Providing and fixing Antique brass handle ring including all cost and labour charges (Brass Heavy duty )

od250952/2019_2020 : Providing and fixing of door lock: Atom six turn Lock and ultra key including all cost and labour charges etc.complete

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference.

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Make: Asian, Berger, Nerolac or eq. in the order of pref.

11.26.1 : Kota stone slab flooring over 20 mm ( average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)25 mm thick including prior sample approval etc complete as per the direction of Engineer at site.

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

od250974/2019_2020 : Providing and fixing good quality Second class teak wood / Jack wood handrails with top section of size 10.00cm x 6.00cm and vertical section of size 4.45cm x 4.45cm. with the architectural design, approval of Client/ KEL including all cost and labour charges etc. complete as per the direction of Engineer at site.

od253515/2019_2020 : Providing and fixing good quality Second class teak wood / Jack wood eaves board 20 cm wide and 2.5 cm thick with the architectural design, approval of Client/ KEL including all cost and labour charges etc. complete as per the direction of Engineer at site.

16.79 : Providing , laying spreading and compacting graded stone aggregate ( size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub - base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer - in- Charge. (Quantity by level calculation and reporting to CTE as per norms and quality test at Govt. lab).

od251311/2019_2020 : Providing and laying rough finish granite stone (sadarhalli ) flooring in required design and pattern (90x50 cm or nearest) in linear as well as curvilinear all complete as per the architectural drawing with 50mm thick stone slab over 50mm thick base of sand etc. complete as specified and as directed by the engineer in charge.

13.48.1 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm. Make: Jotun,Asian, Berger, Nerolac or eq. in the order of pref.

od250956/2019_2020 : Polyurethane based Melamine spray polishing: -Two or more coats on new works including a coat of wood filler, melamine primer. Melamine sealer etc.

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

od252352/2019_2020 : Supply testing and commisioning the following type 5 nos CCTV unit with all accessories - HONEYWELL HWCHABC2005PI 1080p Bullet Camera Fixed Lens 3pt6 mm, HONEYWELL 16 CHANNEL 1080p DVR , WD 4 TB HARD DISK, 0 AMPS POWER SUPPLY, BNC connector (MX), DC Pin Connector, RG 59 Cable supply, 4U Rack with PDU, LG 18.5" Display, as per design, drawing, prior approval of client/ KEL. and the direction of Engineer in charge.

od252353/2019_2020 : Providing and fixing Two tired open shelf of size 200 x 120 and 5 or more rack using good quality Second class teak wood / Jack wood as per the direction of Engineer in charge

od252354/2019_2020 : Providing and fixing Centre Table of Size 3’x1.5’x1.5’ made of seasoned sheesham wood / sunmica top frame 19 mm commercial ply board with good quality of sunmica finished with sprit polish using Legs 16”x1 ¾”x1 ¾” tapered top rail 2”x1” thick top side rail 2”x1” thick bottom rail 1.5”x ¾’ thick top frame 3”x1” thick. all complete as per design, drawing, prior approval of client/ KEL. and the direction of Engineer in charge.

od252355/2019_2020 : Providing and fixing Wooden armless chair made of seasoned sheesham wood finished with sprit polish using Front legs 2”x2” tapered, back legs 1 ¼” thick (curved), top rail and seat rail 1” thick, under framing 1 ¼” x7/8” slates 1”x3/8” sheet frame and shape of wood 1 ¾” thick seat slates 1 ½”x1 ½”x3/4 back height 34” seat height 18”, depth 18”, seat front 18”, width of back 16” all complete as per design, drawing, prior approval of client/ KEL. and the direction of Engineer in charge.

od252356/2019_2020 : Providing and fixing Wooden armed office chair made of seasoned sheesham wood, cane seat and back finished with sprit polish , using Front leg 2”x2” turned, back legs 1-3/8” seat rails 2 ½”x2 ½”, back top rail 2 ½”x1” curved shape back slates 1 ¾”x7/8” middle rail 1 ¾” arms 7/8” thick and bottom rail 1 ¾”, width of front of seat 22” width of back 19” of seat (including back legs, 18” height of arms 9” and height of back 38”) all complete ,as per design, drawing, prior approval of client/ KEL. and the direction of Engineer in charge.

TRAINING AND PERFORMANCE CENTRE

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position Cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size). Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers. (Centering and shuttering for different category of work may be considered separately.)

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo - Mechanically Treated bars of grade Fe-500D or more. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference.

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.6.7.2 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference.

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work. Make: Asian, Berger, Nerolac or eq. in the order of pref.

12.48 : Providing & fixing on Roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately) including prior sample approval and direction of Engineer at site.

12.49 : Providing & laying on Roof pressed clay tile ridge (Mangalore tile) of 20 mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately ). including prior sample approval and direction of Engineer at site.

od253515/2019_2020 : Providing and fixing good quality Second class teak wood / Jack wood eaves board 20 cm wide and 2.5 cm thick including all material and labour charges etc. complete.

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

50.13.1 : 9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

50.9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality second class teak wood /jack wood

9.5.1.1 : Providing and fixing panelled or panelled and glazed shutters for shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer - in-charge.Second class teak wood 35 mm thick shutters

9.7.1 : Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:Second class teak wood

od250948/2019_2020 : Providing and fixing 8" or nearest size punit antique tower bolt including all cost and labour charges (Brass Heavy duty )

od250949/2019_2020 : Providing and fixing 4"or nearest size punit antique tower bolt antique including all cost and labour charges (Brass Heavy duty )

od250950/2019_2020 : Providing and fixing 4" SS punit hinges antique ( approved by the engineer)including all cost and labour charges.(Heavy duty )

od250951/2019_2020 : Providing and fixing antique brass handle ring including all cost and labour charges (Brass Heavy duty )

od250952/2019_2020 : Providing and fixing of Door lock: Atom six turn Lock and ultra key including all cost and labour charges etc.complete

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer. Make: Asian, Berger, Nerolac or eq. in the order of pref.

13.48.1 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm. Make: Jotun,Asian, Berger, Nerolac or eq. in the order of pref.

od253062/2019_2020 : Polyurethane based Melamine spary polishing : -Two or more coats on new works including a coat of wood filler, melamine primer. Melamine sealer etc.(14.70.1 (derived))

11.26.1 : Kota stone slab flooring over 20 mm ( average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)25 mm thick including prior sample approval etc complete as per the direction of Engineer at site.

od249299/2019_2020 : Providing & fixing on Roof pressed clay ceiling tiles 30x25mm size of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately) including prior sample approval etc complete as per the direction of Engineer at site.

od249158/2019_2020 : Exposed Laterite masonry in CM 1:6 (1 cement : 6 course sand) for superstructure above plinth level up to floor two level with neatly dressed best quality laterite stones of size 30x20x20 cm.including all cost of materials, labour charges, conveyance, curing etc. complete as per standard specification.

od252352/2019_2020 : Supply testing and commisioning the following type 5 nos CCTV unit with all accessories - HONEYWELL HWCHABC2005PI 1080p Bullet Camera Fixed Lens 3pt6 mm, HONEYWELL 16 CHANNEL 1080p DVR , WD 4 TB HARD DISK, 0 AMPS POWER SUPPLY, BNC connector (MX), DC Pin Connector, RG 59 Cable supply, 4U Rack with PDU, LG 18.5" Display, as per design, drawing, approval of Client/ KEL and the direction of engineering in charge.

od252353/2019_2020 : Providing and fixing Two tired open shelf of size 200 x 120 and 5 or more rack using good quality Second class teak wood / Jack wood as per design, drawing, approval of Client/ KEL and the direction of engineering in charge.

od252354/2019_2020 : Providing and fixing Centre Table of Size 3’x1.5’x1.5’ made of seasoned sheesham wood / sunmica top frame 19 mm commercial ply board with good quality of sunmica finished with sprit polish using Legs 16”x1 ¾”x1 ¾” tapered top rail 2”x1” thick top side rail 2”x1” thick bottom rail 1.5”x ¾’ thick top frame 3”x1” thick. all complete as per design, drawing, approval of Client/ KEL and the direction of engineering in charge.

od252355/2019_2020 : Providing and fixing Wooden armless chair made of seasoned sheesham wood finished with sprit polish using Front legs 2”x2” tapered, back legs 1 ¼” thick (curved), top rail and seat rail 1” thick, under framing 1 ¼” x7/8” slates 1”x3/8” sheet frame and shape of wood 1 ¾” thick seat slates 1 ½”x1 ½”x3/4 back height 34” seat height 18”, depth 18”, seat front 18”, width of back 16” all complete as per design, drawing, approval of Client/ KEL and the direction of engineering in charge.

od252356/2019_2020 : Providing and fixing Wooden armed office chair made of seasoned sheesham wood, cane seat and back finished with sprit polish , using Front leg 2”x2” turned, back legs 1-3/8” seat rails 2 ½”x2 ½”, back top rail 2 ½”x1” curved shape back slates 1 ¾”x7/8” middle rail 1 ¾” arms 7/8” thick and bottom rail 1 ¾”, width of front of seat 22” width of back 19” of seat (including back legs, 18” height of arms 9” and height of back 38”) all complete as per design, drawing, approval of Client/ KEL and the direction of engineering in charge.

COFFEE KIOSK

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position Cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size). Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers. (Centering and shuttering for different category of work may be considered separately.)

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference.

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.6.7.2 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

od249158/2019_2020 : Exposed Laterite masonry in CM 1:6 (1 cement : 6 course sand) for superstructure above plinth level up to floor two level with neatly dressed best quality laterite stones of size 30x20x20 cm.including all cost of materials, labour charges, conveyance, curing etc. complete as per standard specification.

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference.

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work. Make: Asian, Berger, Nerolac or eq. in the order of pref.

12.48 : Providing & fixing on Roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately) including prior sample approval and direction of Engineer at site.

od249299/2019_2020 : Providing & fixing on Roof pressed clay ceiling tiles 30x25mm size of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately). including prior sample approval and direction of Engineer at site.

12.49 : Providing & laying on Roof pressed clay tile ridge (Mangalore tile) of 20 mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately ). including prior sample approval and direction of Engineer at site.

od253515/2019_2020 : Providing and fixing good quality Second class teak wood / Jack wood eaves board 20 cm wide and 2.5 cm thick including all material and labour charges etc. complete.

9.7.1 : Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:Second class teak wood

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Make: Asian, Berger, Nerolac or eq. in the order of pref.

13.48.1 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm. Make: Jotun,Asian, Berger, Nerolac or eq. in the order of pref.

11.26.1 : Kota stone slab flooring over 20 mm ( average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)25 mm thick including prior sample approval and direction of Engineer at site.

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

od252352/2019_2020 : Supply testing and commisioning the following type 5 nos CCTV unit with all accessories - HONEYWELL HWCHABC2005PI 1080p Bullet Camera Fixed Lens 3pt6 mm, HONEYWELL 16 CHANNEL 1080p DVR , WD 4 TB HARD DISK, 0 AMPS POWER SUPPLY, BNC connector (MX), DC Pin Connector, RG 59 Cable supply, 4U Rack with PDU, LG 18.5"Display, as per design, drawing, approval from Client/KEL and the direction of engineering in charge.

od252353/2019_2020 : Providing and fixing Two tired open shelf of size 200 x 120 and 5 or more rack using good quality Second clas teak wood / Jack wood as per design, drawing, approval from Client/KEL and the direction of engineering in charge.

od252354/2019_2020 : Providing and fixing Centre Table of Size 3’x1.5’x1.5’ made of seasoned sheesham wood / sunmica top frame 19 mm commercial ply board with good quality of sunmica finished with sprit polish using Legs 16”x1 ¾”x1 ¾” tapered top rail 2”x1” thick top side rail 2”x1” thick bottom rail 1.5”x ¾’ thick top frame 3”x1” thick. all complete as per design, drawing, approval from Client/KEL and the direction of engineering in charge.

od252355/2019_2020 :Providing and fixing Wooden armless chair made of seasoned sheesham wood finished with sprit polish using Front legs 2”x2” tapered, back legs 1 ¼” thick (curved), top rail and seat rail 1” thick, under framing 1 ¼” x7/8” slates 1”x3/8” sheet frame and shape of wood 1 ¾” thick seat slates 1 ½”x1 ½”x3/4 back height 34” seat height 18”, depth 18”, seat front 18”, width of back 16” all complete as per design, drawing, approval from Client/KEL and the direction of engineering in charge.

od252356/2019_2020 : Providing and fixing Wooden armed office chair made of seasoned sheesham wood, cane seat and back finished with sprit polish , using Front leg 2”x2” turned, back legs 1-3/8” seat rails 2 ½”x2 ½”, back top rail 2 ½”x1” curved shape back slates 1 ¾”x7/8” middle rail 1 ¾” arms 7/8” thick and bottom rail 1 ¾”, width of front of seat 22” width of back 19” of seat (including back legs, 18” height of arms 9” and height of back 38”) all complete as per design, drawing, approval from Client/KEL and the direction of engineering in charge.

COW SHED

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position Cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers. (Centering and shuttering for different category of work may be considered separately.)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference.

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.6.7.2 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference.

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work. Make: Make: Asian, Berger, Nerolac or eq. in the order of pref.

12.48 : Providing & fixing on Roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately) including prior sample approval and direction of Engineer at site.

od249299/2019_2020 : Providing & fixing on Roof pressed clay ceiling tiles 30x25mm size of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately).including prior sample approval and direction of Engineer at site.

12.49 : Providing & laying on Roof pressed clay tile ridge (Mangalore tile) of 20 mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately ). including prior sample approval and direction of Engineer at site.

od253515/2019_2020 : Providing and fixing good quality Second class teak wood / Jack wood eaves board 20 cm wide and 2.5 cm thick including all material and labour charges etc. complete.

9.7.1 : Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:Second class teak wood

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer. Make: Asian, Berger, Nerolac or eq. in the order of pref.

13.48.1 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm. Make: Jotun,Asian, Berger, Nerolac or eq. in the order of pref.

11.26.1 : Kota stone slab flooring over 20 mm ( average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)25 mm thick (prior sample approval).

od252352/2019_2020 : Supply testing and commisioning the following type 5 nos CCTV unit with all accessories - HONEYWELL HWCHABC2005PI 1080p Bullet Camera Fixed Lens 3pt6 mm, HONEYWELL 16 CHANNEL 1080p DVR , WD 4 TB HARD DISK, 0 AMPS POWER SUPPLY, BNC connector (MX), DC Pin Connector, RG 59 Cable supply, 4U Rack with PDU, LG 18.5" Display, as per design, drawing, approval from Client/ KEL and the direction of engineering in charge.

TICKET COUNTER

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers. (Centering and shuttering for different category of work may be considered separately.)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference.

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete. Min. average compressive strength as per IS shall be 40-50kg/cm2 and has to be assessed by testing at Govt. lab. ( Variation in rate due to change in size of block and level of floor as per DSR/PRICE has to be considered).

50.6.7.2 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

od249158/2019_2020 : Exposed Laterite masonry in CM 1:6 (1 cement : 6 course sand) for superstructure above plinth level up to floor two level with neatly dressed best quality laterite stones of size 30x20x20 cm.including all cost of materials, labour charges, conveyance, curing etc. complete as per standard specification.

50.9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Second class teak wood /jack wood

12.48 : Providing & fixing on Roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately).including prior sample approval and direction of Engineer at site.

12.49 : Providing & laying on Roof pressed clay tile ridge (Mangalore tile) of 20 mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately ).including prior sample approval and direction of Engineer at site.

od249299/2019_2020 : Providing & fixing on Roof pressed clay ceiling tiles 30x25mm size of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately).including prior sample approval and direction of Engineer at site.

od253515/2019_2020 : Providing and fixing good quality Second class teak wood / Jack wood eaves board 20 cm wide and 2.5 cm thick including all material and labour charges etc. complete.

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer. Make: Asian, Berger, Nerolac or eq. in the order of pref.

13.48.1 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm. Make: Jotun,Asian, Berger, Nerolac or eq. in the order of pref.

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work. Make: Asian, Berger, Nerolac or eq. in the order of pref.

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes. Make: TATA, JSW, VIZAG, SAIL or eq.

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

9.5.1.1 : Providing and fixing panelled or panelled and glazed shutters for shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer - in-charge.Second class teak wood35 mm thick shutters

od252352/2019_2020 : Supply testing and commisioning the following type 5 nos CCTV unit with all accessories - HONEYWELL HWCHABC2005PI 1080p Bullet Camera Fixed Lens 3pt6 mm, HONEYWELL 16 CHANNEL 1080p DVR , WD 4 TB HARD DISK, 0 AMPS POWER SUPPLY, BNC connector (MX), DC Pin Connector, RG 59 Cable supply, 4U Rack with PDU, LG 18.5" Display, as per design, drawing, approval from Client/ KEL and the direction of engineering in charge.

od252353/2019_2020 : Providing and fixing Two tired open shelf of size 200 x 120 and 5 or more rack using good quality Second class teak wood / Jack wood as per design, drawing, approval from Client/ KEL and the direction of engineering in charge.

od252354/2019_2020 : Providing and fixing Centre Table of Size 3’x1.5’x1.5’ made of seasoned sheesham wood / sunmica top frame 19 mm commercial ply board with good quality of sunmica finished with sprit polish using Legs 16”x1 ¾”x1 ¾” tapered top rail 2”x1” thick top side rail 2”x1” thick bottom rail 1.5”x ¾’ thick top frame 3”x1” thick. all complete as per design, drawing, approval from Client/ KEL and the direction of engineering in charge.

od252355/2019_2020 : Providing and fixing Wooden armless chair made of seasoned sheesham wood finished with sprit polish using Front legs 2”x2” tapered, back legs 1 ¼” thick (curved), top rail and seat rail 1” thick, under framing 1 ¼” x7/8” slates 1”x3/8” sheet frame and shape of wood 1 ¾” thick seat slates 1 ½”x1 ½”x3/4 back height 34” seat height 18”, depth 18”, seat front 18”, width of back 16” all complete as per the direction of engineer incharge

od252356/2019_2020 : Providing and fixing Wooden armed office chair made of seasoned sheesham wood, cane seat and back finished with sprit polish , using Front leg 2”x2” turned, back legs 1-3/8” seat rails 2 ½”x2 ½”, back top rail 2 ½”x1” curved shape back slates 1 ¾”x7/8” middle rail 1 ¾” arms 7/8” thick and bottom rail 1 ¾”, width of front of seat 22” width of back 19” of seat (including back legs, 18” height of arms 9” and height of back 38”) all complete as per the direction of engineering incharge

LANDSCAPING

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

5.1.2 : Providing and laying in position specified grade of Reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size.

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

30.2.2 : Supplying and stacking of good earth at site including royalty and carriage upto 5 k.m. lead complete (earth measured in stacks will be reduced by 20% for payment).

30.2.3 : Supplying and stacking sludge at site including royalty and carriage upto 5 k.m. lead complete (sludge measured in stacks will be reduced by 8% for payment).

30.2.8 : Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

30.2.9 : Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

od255028/2019_2020 : Providing and Planting of Buffalo grass for Lawn in Ordinary soil including Breaking clods, Watering, Ramming and Sectioning of spoil bank etc., including all material , labour charges and watering till handovering over site to Client etc., complete

od255029/2019_2020 : Supplying and fixing neatly dressed shaped Rubble 30 x 30 x 7.5 cm or nearest available size paving tiles over bed of coarse sand of average thickness 50 mm after levelling and compacting the sub base, filling the joints with fine sand including cost and conveyance of all materials and labour charges etc. complete as per the direction of departmental officers.

od255030/2019_2020 : Supplying and planting of approved trees species of a height 1.m to 2.m ,at the specified location as shown in the drawing .Rate shall include Cost of plants and good earth, planting of trees sapling, replacement of dead trees, watering and maintenance till the completion of project work as per the directions of the engineer in charge.

50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge. (After deducting earth available at site from excavation).

50.18.7.3.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer- in- Charge 25 mm dia 12 Kgf/cm2 - Internal work - Exposed on wall

18.51.1 : Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.55.1 : Providing and fixing PTMT stop cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms

16.79 : Providing , laying spreading and compacting graded stone aggregate ( size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub - base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer - in- Charge. (Quantity by level calculation and reporting to CTE as per norms).

Outside Electrification

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

5.1.2 : Providing and laying in position specified grade of Reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete. (Centering and shuttering for different category of work may be considered separately.)

od253788/2019_2020 : CABLING - Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required - 4 core 10 sq mm with factory made clamp and 25mm PVC pipe with prior sample approval.

od255031/2019_2020 : Supplying and fixing 225x380 mm Post top Light (Classic Medium. Clear Diffuser. Material: Resin Moulded in black ) with 15w Bulb etc all complete with prior sample approval. as per the direction of Engineer in charge

od255032/2019_2020 : Supplying and fixing following complete Cast Iron 2.5 mtr height ornamental pole , minimum weight 110kg, including the cost of conveying, loading, unloading, erection charge ,foundation bolt, plate, 2.5sqmm wire, etc all complete as per the direction of Engineer in charge

Electrification Works for Gallery,Training centre,Week end market,Coffee kiosk, Cow shed, Ticket counter

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.22.5 : Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.180 mm X 100 mm X 60 mm deep

1.23.3 : Supplying and fixing following piano type switch / socket on the existing switch box/ cover including connections etc. as required.15/16 amp switch

1.23.5 : Supplying and fixing following piano type switch / socket on the existing switch box/ cover including connections etc. as required.6 pin 15/16 amp socket outlet

1.33 : Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden blockincluding connection etc as required.

WEEKEND MARKET SPACE

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers. (Centering and shuttering for different category of work may be considered separately.)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference.

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge. (After deducting earth available at site from excavation).

od249158/2019_2020 : Exposed Laterite masonry in CM 1:6 (1 cement : 6 course sand) for superstructure above plinth level up to floor two level with neatly dressed best quality laterite stones of size 30x20x20 cm.including all cost of materials, labour charges, conveyance, curing etc. complete as per standard specification.

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete. Min. average compressive strength as per IS shall be 40-50kg/cm2 and has to be assessed by testing at Govt. lab. ( Variation in rate due to change in size of block and level of floor as per DSR/PRICE has to be considered).

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes.Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference.

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work. Make: Asian, Berger, Nerolac or eq. in the order of pref.

12.48 : Providing & fixing on Roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately).including prior sample approval and direction of Engineer at site.

12.49 : Providing & laying on Roof pressed clay tile ridge (Mangalore tile) of 20 mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately ).including prior sample approval and direction of Engineer at site.

od249299/2019_2020 : Providing & fixing on Roof pressed clay ceiling tiles 30x25mm size of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately).including prior sample approval and direction of Engineer at site.

od253515/2019_2020 : Providing and fixing good quality Second class teak wood / Jack wood eaves board 20 cm wide and 2.5 cm thick including all material and labour charges etc. complete.

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

9.7.1 : Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:Second class teak wood

11.26.1 : Kota stone slab flooring over 20 mm ( average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)25 mm thick (Sample approval)

od252352/2019_2020 : Supply testing and commisioning the following type 5 nos CCTV unit with all accessories - HONEYWELL HWCHABC2005PI 1080p Bullet Camera Fixed Lens 3pt6 mm, HONEYWELL 16 CHANNEL 1080p DVR , WD 4 TB HARD DISK, 0 AMPS POWER SUPPLY, BNC connector (MX), DC Pin Connector, RG 59 Cable supply, 4U Rack with PDU, LG 18.5" Display, as per design, drawing, approval from Client/ KEL and the direction of engineering in charge.

od252353/2019_2020 : Providing and fixing Two tired open shelf of size 200 x 120 and 5 or more rack using good quality Second class teak wood / Jack wood as per design, drawing, approval from Client/ KEL and the direction of engineering in charge.

od252354/2019_2020 :Providing and fixing Centre Table of Size 3’x1.5’x1.5’ made of seasoned sheesham wood / sunmica top frame 19 mm commercial ply board with good quality of sunmica finished with sprit polish using Legs 16”x1 ¾”x1 ¾” tapered top rail 2”x1” thick top side rail 2”x1” thick bottom rail 1.5”x ¾’ thick top frame 3”x1” thick. all completeas per design, drawing, approval from Client/ KEL and the direction of engineering in charge.

od252355/2019_2020 : Providing and fixing Wooden armless chair made of seasoned sheesham wood finished with sprit polish using Front legs 2”x2” tapered, back legs 1 ¼” thick (curved), top rail and seat rail 1” thick, under framing 1 ¼” x7/8” slates 1”x3/8” sheet frame and shape of wood 1 ¾” thick seat slates 1 ½”x1 ½”x3/4 back height 34” seat height 18”, depth 18”, seat front 18”, width of back 16” all complete as per design, drawing, approval from Client/ KEL and the direction of engineering in charge.

od252356/2019_2020 : Providing and fixing Wooden armed office chair made of seasoned sheesham wood, cane seat and back finished with sprit polish , using Front leg 2”x2” turned, back legs 1-3/8” seat rails 2 ½”x2 ½”, back top rail 2 ½”x1” curved shape back slates 1 ¾”x7/8” middle rail 1 ¾” arms 7/8” thick and bottom rail 1 ¾”, width of front of seat 22” width of back 19” of seat (including back legs, 18” height of arms 9” and height of back 38”) all complete as per design, drawing, approval from Client/ KEL and the direction of engineering in charge.

Electrical fittings & elevator etc

od253786/2019_2020 : Providing and fixing LED Tube set of 20W including all material and labour charges etc.complete. Make: PHILIPS/ LEGRAND

od253787/2019_2020 : Supplying and installation of following sizes of 1200 mm sweep. 5 star rated ceiling fan, with double ball bearing, Aluminium pressure die cast body with Aluminium blades, canopies, hanging Shackle, 30 cm down rod and without speed regulator suitable for 240V 50Hz, AC supply confirms to IS 374/1979 as required complete. (Make crompton- High speedor equivalent approved make)

od253788/2019_2020 : CABLING - Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required - 4 core 10 sq mm with factory made clamp and 25mm PVC pipe

od253789/2019_2020 : Supply Laying, Testing and Commissioning of following 1100V XLPE A2XFY (XLPE insulated Armoured Aluminium)IN existing trench ,cable trays (Note : Inclusive of supply of Anchor Fasteners, straight through joints and necessary 1.5mm thick GI Flat, clamps shall be included in the laying cost).3C x 16Sq.mm XLPE Al.Ar. Incl excavation, 50mm G.I Pipe ,straight through joints if required

od253790/2019_2020 : Supply Laying, Testing and Commissioning of L&T made metering box with single phase Kwh meter class 1 with all the supporting accessories etc.complete

od253791/2019_2020 : Distribution Board : Supply, erection, earthing, testing and commissioning of the following MCB DBs Metal double Door powder coated including all interconnections and accessories like bolts, nuts and associated civil works. MCB DB s shall have comprising as follows: Double door- Concealed in wall. Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993. IP 52 for indoor IP 54 for kitchen and laundry panels. IP 55 for outdoor . All MCBs used for protection of resistive and lightly inductive load shall be type "B" characteristic and inductive (motor) load shall be of type "C" characteristic and discharge lamps and UPS etc. shall be of type D characteristic. LDB -8W DP MCB DB incoming 63A D.P RCCB, 63A ISOLATER, 10A MCB 24 nos etc.

od253792/2019_2020 : Supply, Installation, Testing and Commissioning of about 1100 mm W X 700mm D - 4 passenger Elevator using 1.0m/s or 0.75m/s speed, 3 phase 430 volt, 50HZ for main supply and 1 phase, 220 volt , 50 hz for lighting power supply, microprocessor control and multy speed, full collective operation, side opening two panels/ centre opening two panels 700 X 2000 VVVF operating door, Stainless steel Hairline finish wall and ceiling with LED Light, Automatic Rescue Device (ARD) Voice announcer with background music, over load sensor etc complete, including cost of all material, labour for erection, testing and commissioning as per the direction of Engineer-in charge

Note: Make of Water supply and sanitary items: Best branded ISI make Jaquar, Cera, Hindware, Parryware or eq. in the order of pref. Water pipe: Supreme, Finolex or eq. with IS and all fittings with IS.

Make of Electrical equipments/materials

All electrical materials/equipments shall be of best branded items with ISI, strictly as per schedule specification

Panel Boards: CPRI certified reputed manufacturers make

MCB/ELCB/DB - L&T/LEGRAND/SCHNEIRDER or equivalent

Cables & wires - Finolex/KEI/POLYCAB/RPG/V-GUARD

Switches/Sockets/Regulators - SCHEIDER/ABB/HAVELS/LEGRAND or equivalent

Rigid PVCPipes/Casing & Capping - A-ONE/REPUTED MAKE with ISI , Precession, Balco, GEO

Cable Glands & Sockets - REPUTED MAKE , Cosmos

Indicating Lamps - TEKINIC/RISHUB/STC, L&T, Schneider or equivalent

Ceiling/Exhaust fan: Havells, Orient, Usha, Crompton Greaves, Bajaj

Push Button- L&T, Schneider, Rishabh

Rate should be inclusive of preparation of schematic diagram and getting approval from KSEB/Electrical Inspectorate. Statutory fees paid to KSEB/EI shall be paid by us separately.

Detailed list of Approved brands/ make enclosed.

Note :1 All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL

2:Rate should be inclusive of Insurance,Transportation, delivery and installation cost for all items

3.Rate should be Exclusive of GST.

4.Work should be executed as per DSR/PWD specification and direction of Engineer at site.

TEAMEDGE DEVELOPERS AND LAND CONSTRUCTION PVT LTD

CUBIX INFRASTRUCTURES