SPECIAL REPAIRS TO BLDG NO II-17A SINGLE OFFICERS ACCN AT WEST HILL, CALICUT UNDER AGE (I) CANNANORE.

Amount

Dismantling of single layer MP roof tiles or similar tiles in roofing complete all as specified and as directed.

Dismantling of Battens for tiles, shingles etc of any size including tilting fillets exceeding 15cm spacing complete all as specified and as directed.

Dismantling timber scantlings 40sqcm and over in sectio,n in any position, in framed work complete all as specified and as directed.

M&L second class hardwood scantlings framed and fixed, clean sawn as in rafters, purlins etc. complete all as specified and as directed.

S&F Mild steel structural steel work of rectangular or square tubular section as in purlins/battens including special shaped washers etc. Fe-410-W (Gde-E-250) quality B etc. complete all as specified and as directed.

S&F Mild steel rolled sections as in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. using Fe 410-W Gde E-250 Qlty -A (cut to ordinary lengths i.e. Within 20mm of the length indicated) complete all as specified and as directed.

S&F Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe-410W E-250 quality 'A' complete all as specified and as directed.

M&L PCC 1:2:4, Type B1, using 20mm graded stone aggregate as in roof kerbs of mud stops, rounded or chamfered on edge complete all as specified and as directed.

S&F Pre painted galvalume aiuminium zinc coating GI based corrugated steel sheet 0.5mm thick colour coated having tensile strength 550MPa as in roofing/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre painted galvalume aiuminium zinc coating GI based plain steel sheet 0.5mm thick colour coated having tensile strength 550MPa as in roofing/Ridge/Valley gutter fixed with self tapping screws compllete all as specified and as directed.

M&L Preparation of surfaces of wood and wood based materials, new or old surfaces of any description and girth not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L Preparation of new or previously untreated steel surfaces of any descriptions and applying two coats of synthetic enamel paint over a coat of zinc chromium primer over 10cm width or girth complete all as specified and as directed.

Taking down cement or cement lime plaster including raking out joints, hacking for key, scrubbing down with water etc.of any deccription complete all as specified and as directed.

M&L 10mm thick Rendering in CM 1:6 on stone masonry surfaces to be finished even and smooth with out using extra cement (internal wall surfaces) complete all as specified and as directed.

M&L 15mm thick Rendering in CM 1:4 on stone masonry surfaces to be finished even and smooth with out using extra cement (external wall surfaces) complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness, including cover fillets all as specified and as directed

M&L Anodised aluminium snap grid of size 605x605mm frame work for false ceiling complete all as specified and as directed.

M&L Hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof by means of ceiling cleats made out of GI flat 40x3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and as directed.

M&L Non asbestos fibre cement buildings boards of 4mm thick inserted to aluminium frame work with screws complete all as specified and as directed.

M&L Preperation of new unplastered ceiling surfaces and applying two coats of distempering oil emulsions over 3mm thick wall care putty followed a coat of chalk whiting preparatory to distempering, complete all as specified and as directed.

Demolition of brick work or concrete/ stone masonry wall built in cement mortar complete all as specified and as directed.

M&L Walling of laterite stone walls built in cement mortar 1:6, uncoursed, well bonded bedded and solidly hearted complete all as specified and as directed.

Demolition of cement concrete (unreinforced) not exceeding 15cm thickness in ground floors and pavings work complete all as specified and as directed.

M&L 25mm thick cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in floor complete all as specified and as directed.

M&L 20mm thick screed bed or bedding layer in cement mortar 1:4, for laying floor finishes complete all as specified and as directed.

M&L Rendering 10mm thick in CM 1:4 on stone masonry surfaces as in backing coat for wall tiling, surfaces finished rough complete all as specified and as directed.

M&L Vitrified Ceramic tiles of light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors etc., complete all as specifed and as directed.

M&L Glazed ceramic tile 350x250x7mm/450x350x7mm thick as set and jointed in neat cement slurry and pointed in white or coloured cement to match in vertical surface complete all as specified and as directed.

Taking down chowkats or frames with shutter (without taking off shutter from frames) of any description exc 1.5sqm but not exc 4sqm each complete all as specified and as directed.

Taking down shutters of any description exc 2.00 Sqm each and refixing in same opening complete all as specified and as directed.

Taking down chowkats or frames with shutter (without taking off shutter from frames) of any description n.exc 1.5 sqm each complete all as specified and as directed.

S&F flat iron hold fast and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

M&L Cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate including necessary form work etc complete all as specified and as directed.

S&F second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as apecified and directed.

S&F 30mm thick plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and as directed.

M&L 30mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc., divided into squares, with plain, chamfered or rounded,mitred and rebated sash bars,any numbers fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); and fitted to chowkats complete all as specified and as directed.

S&F sheet glass, 3 mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F stainless wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staples complete all as specified and as directed.

M&L 2nd class hard wood plain fillets square, rectangular or triangular in section clean sawn secured with nails exc 6 and n.exc 13 Sqcm in section all as specified and directed.

M&L Preparation of new wooden surfaces and applying two coats of synthetic enamel painting over a coat of primer surfaces over 10 cm width or girth complete all as specified and as directed.

M&L Preparation of old wooden surfaces and applying one coat of synthetic enamel paint surfaces over 10 cm width or girth complete all as specified and as directed.

M&L Complete removal of existing treatment from wall surfaces by scrapping down old treatment and applying two coats of oil emulsion distemper over 3mm thick wall care putty followed a coat of chalk whiting preparatory to distempering,complete all as specified and as directed

M&L Preparation of new plastered surfaces of walls, and applying two coats of oil emulsion distemper over 3mm thick wall care putty followed a coat of chalk whiting preparatory to distempering, complete all as specified and as directed.

M&L Complete removal of existing treatment from external walls by scrapping down old treatment and applying two coats of exterior grade anti-algae acrylic emulsion paint over one coat of wall primer including preparation of surfaces using wall care putty etc complete all as directed as per manufacturers instructions.

M&L Preparing newly plastered surfaces of external walls and applying two coats of exterior grade anti-algae acrylic emulsion paint over one coat of wall primer over wall care putty complete all as directed as per manufacturers instructions.

M&L Preparing back of chowkats of area tarred exceeding 0.1 sqm but not exceeding 0.50 Sqm each and treated with tar or coal tar black paint complete all as specified and as directed.

S&F 150mm size, aluminum anodized barrel tower bolts of extruded section complete all as specified and as directed.

S&F Harrison rails 25mm dia, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as directed.

S&F 100mm size, stainless steel butt hinges medium weight complete all as specified and as directed.

S&F 75mm size, stainless steel butt hinges, medium weight complete all as specified and as directed.

S&F 150mm size, extruded aluminum alloy handle, fabricated type, anodized complete all as specified and as directed.

S&F 300mm long, aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F floor door stopper overall length of cover plate 140mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

Taking down carefully copper/aluminium point wiring of light, fan, socket or power complete, including fitting such as switches, ceiling roses, pendants, regulators, scokets etc. and making good distrurbed surfaces of walls, floor ceiling etc. complete all as specified and as directed.

M&L Point wiring with 1.5 Sqmm single core, PVC insulated, unsheathed copper conductor FRLS cable, multi-stranded 1100 V grade drawn through and including non-metallic rigid PVC conduct, concealed in wall complete, fixed in roof, etc with necessary fixing accessories such as bend, elbow, socket, saddles etc with and including 1.5 sqmm, single core PVC insulated unsheathed copper conductor FRLS cables multi stranded, 1100 volt grade green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed for:-

One light point controlled by one switch

One ceiling fan / exhaust point controlled by one switch

One bell point controlled by one switch

One 3 pin, 5 Amps switch socket combination on independent board

One 3 pin, 5 Amps switch socket combination on same board with other switches

All as per srl item No 55 above, but for one 3 pin, 15 Amps, switch socket combination on independent board with FRLS cable of size 4 Sqmm with and including 4 sqmm copper conductor cable as earth continuity conductor green in colour and connected to common earth dolly complete all as specified and as directed.

M&L Cutting chases on wall of width 30mm, depth 35mm for concealing PVC conduct of 20/25mm dia, with and including replastering, smooth finishing to match the existing colour of the wall complete all as specified and as directed.

M&L Cutting chases on wall of width 50 mm, depth 35mm for concealing PVC conduit of 20/25 mm dia, with and including replastering, smooth finishing to match the existing colour of the wall complete all as specified and directed

M&L Cutting chases on wall of width 75mm, depth 35 mm for concealing PVC conduct of 20/25mm dia, with and including replastering, smooth finishing to match the existing colour of the wall complete all as specified and directed

S&F Modular switch, 240 V, one way, single pole, 6 Amps one module including connecting up electrically complete all as specified and as directed.

S&F Modular switch, 240 V, one way, single pole, 16 Amps one module including connecting up electrically complete all as specified and as directed.

S&F Switch, bell push modular type, 240 V, 6 Amps one module including connecting up electrically complete all as specified and as directed.

S&F Ceiling rose of polycarbonate, 3 terminal including connecting up electrically complete all as specified and as directed.

S&F Socket outlet, 2/3 pin, 6 Amps, multipurpose, modular type, including connecting up electrically complete all as specified and directed.

S&F Socket outlet, modular type, 2 in 1, 2/3 pin, 6 & 16 Amps, including connecting up electrically complete all as specified and as directed.

S&F Calling bell, AC, 240V, single pole including connecting up electrically complete all as specified and as directed.

S&F modular white cover plate with frame for two module complete all as specified and as directed.

S&F modular white cover plate with frame for three module complete all as specified and as directed.

S&F modular white cover plate with frame for four module complete all as specified and as directed.

S&F modular white cover plate with frame for six module complete all as specified and as directed.

S&F modular white cover plate with frame for eight module complete all as specified and as directed.

S&F modular metal flush box for one/two module complete all as specified and as directed.

S&F modular metal flush box for three module complete all as specified and as directed.

S&F modular metal flush box for four module complete all as specified and as directed.

S&F modular metal flush box for six module complete all as specified and as directed.

S&F modular metal flush box for eight module complete all as specified and as directed.

S&F in replacement sheet metal enclosures distribution boards, double door 4 way three phase 415 volts MCCB, ISOLATOR & MCBs comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following:- (a) MCCB 4 Pole 100 AMPS AC 415 V 10 KA=01 No as incoming & (b) MCB SP 32 AMP -12 Nos 32 AMP as outgoing (Note :- (i)The DB shall be VTPN series of Make: Hagger CAT PART No VYV04DMZ or techno commercially equivalent. (ii) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost. (iii) Connection of the MCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble-properly crimped. (iv) All the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) double continuous earth wire shall be provided for each three phase DB from earthing mains dolly.

S&F sheet metal enclosure factory made for MCB DB, SP 8 way with 200 Amps bus bar 415 Volt, double door type, fixed/flushed on wall including electrically connecting up complete all as specified and directed.

S&F MCB SP, 240 Volt, 6 to 32 Amps including electrically connecting up using wiring lugs complete all as specified and as directed.

S&F MCB SPN, 240 Volt, 40 Amps including electrically connecting up using wiring lugs complete all as specified and as directed.

Taking down unserviceable fluorescent tube light fittings, supply and fixing Decorative ultra slim linear LED light fittings with extruded Aluminium, heat sink, environmental friendly, energy efficient ready to use pack of E-LITE LED of 20 W LED 6000K, complete all as specified and as directed. Model LheXBYPnin1W020 of Havells or techno commercially equivalent.

Taking down unserviceable tube light fitting and supply and fixing decorative ultra slim linear LED light fittings with extruded Aluminium, heat sink, environmental friendly, energy efficient ready to use pack of E-LITE LED OF 10W LED 6000K, complete all as specified and as directed. Model LheXBYPnin1W010 of Havells or techno commercially equivalent

Taking down old unserviceable bulk heading fitting from wall and supply and fixing Building LED security light fitting. 30 watts Energy saving and environmental friendly long life, made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having IP65 protection and Impact resistance of IK07 with 10KV Built-in Surge Protection Device with suitable GI Bracket complete all as specified and as directed. Make Havells ENDURACITYLITEPLATPLUSSL30WLED757SASYBOPC or techno commercially equivalent

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

M&L Earthing with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron connected to earthing test point, main DB, panel board, continuous earth lead protected by 15mm bore GI pipe light grade, 20mm bore GI light grade pipe for watering, necessary excavation and earth work in any type of soil, PCC pit, RCC chamber cover with suitable reinforcement complete all as shown on electrical plate No 3 of SSR part-I of 2009 all as specified and directed. Note :- Rate quoted shall deem to include for GI earth and GI pipe lead upto 7.5m length.

S&F in replacement LED Ball type Lamp 10 watt complete all as specified and as directed.

M&L Sub main wiring with two runs of single core 4 Sqmm copper conductor FRLS cable, PVC insulated, unsheathed multistanded, 1100 V grade drawn through and including non metallic rigid PVC with all accessories such as bend, elbow, socket, tee saddles etc fixed concealed to wall / fixed to ceiling etc including 2.5Sqmm single core copper conductor FRLS cable PVC insulated, unsheathed multistranded 1100 V grade as earth continuity conductor connected to common earth dolly complete all as specified and directed. Note :- 2 runs of 4 Sq mm and one run of 2.5 Sq mm copper cable and one run of PVC conduit will be measured as one length.

M&L Sub main wiring with two runs of single core 6 Sq mm copper conductor FRLS cable, PVC insulated, unsheathed multistanded, 1100 V grade drawn through and including non metallic rigid PVCwith all accessories such as bend, elbow, socket, tee saddles etc., fixed concealed to wall / fixed to ceiling etc., including 4 Sqmm single core copper conductor FRLS cable PVC insulated, unsheathed multistranded 1100 V grade as earth continuity conductor connected to common earth dolly complete all as specified and directed. Note :- 2 runs of 6 Sq mm and one run of 4 Sq mm copper cable and one run of PVC conduit will be measured as one length.

S&F Modular type fan regulator, stepped type 120 w, 2 module suitable for ceiling fan 230 v, 1200 sweep BEE, 5 star rated complete all as specified and as directed.

Taking down carefully ceiling fan/Exhaust fan with rod from ceiling / roof/wall and refixing the same after repairs such as servicing, greasing, replacement of ceiling fan down rod of suitable length, clamps, nuts, washers, rubber bushes, safety pin etc as required and applying one coat of white synthetic enamel paint and writing of MES No including connecting up with 2 core twisted flexible copper conductor 23/0.0076 from ceiling rose to fan, test and commissioning complete all as specified and as directed.. Note : Rewinding and replacement of capacitor & bearing shall be measured and paid separately.

Rewinding of ceiling fan 1200 mm sweep/Exhaust fan any type and make, cutting and removing burnt winding wire without damaging stator, removing old insulation of polyester paper, re-winding fan motor with super enameled copper wire of same gauge/dia with correct number of turns for auxiliary and main winding, varnishing, baking, soldering new lead of twin core multi-stranded copper conductor cable of size 23/0.0076, assembling, re-fixing including two coats of painting, testing and commissioning complete all as specified and directed.

Supply only ball bearing of suitable for ceiling fan 1200mm sweep including removing old un-serviceable bearing and testing complete all as specified and directed.

S&F sheet metal enclosure with socket single pole and neutral two pin with earth complete with SP MCB of 20 Amps with plug top complete all as specified and as directed.

S&F in repair exhaust fan, plastic body suitable for 250 mm dia sweep with fixing accessories including making hole as per site requirement for suitable size all as specified and directed .Make: Cat Part No FHVVEDXOWH08 of Havells/CG/Bajaj or techno commercially equivalent

NARAYANA CONSTRUCTIONS