Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹27.3 LAccepted-AOC CHANGANACHERRY GENERAL ELECTRICAL WORK | ERNAKULAM | KERALA | 682001 | ₹27.3 L | L1 | Accepted-AOC L1 |
| Sl No | Description | Qty | Unit | ELCON ELECTRICALS L1 |
|---|---|---|---|---|
| 1.00Electrification | ||||
| 1.00 | OD126051/2025-2026:Supply, Conveyance, Installation, testing and Commissioning of 100 KVA DG set on suitable CC foundation as per technical details given below :- i. Engine a. Make of Engine : As Specified in the make of material list b. Type of Engine : Diesel Engine c. No. of Cylinders : Suitable to develop the required BHP as per manufacturers? standard d.Method of Cooling: Water Cooling (with radiator) e. Aspiration : Tubro charged ,inter cooled f. Design : Suitable for generator set application g. Output : BHP ratings specified by the respective manufacturers? capable of delivering the required power for alternator. " "ii. Standard accessories with Diesel Engine a. Flywheel housing and flywheel to suit single bearing alternator (Close coupled arrangement) b. Air Cleaner c. Coolant Kit d. Fuel Pump e. Electronic governor with solid state potentiometer accepting digital pulse input from PLC(backed with mechanical governor if supplied as standard with the set by the manufacturer) f. Fuel filter g. Lubricating Oil filter h. Residential type exhaust silencer iii.Engine Instrument Panel a. Starting switch with key or button b. Lubricating oil temperature gauge c. Lubricating oil pressure gauge. Water temperature gauge e. RPM Indicator with hour meter f. Battery charging ammeter iv. Safety Controls for Engine a. Trip for low lubricating oil pressure b. Trip for high water temperature c. Providing necessary warning system and other safeties as contemplated in relevant ISS d. Fuel shunt off facility at over speed. iv. Fuel Pipe,1 resistant flexible hoses & 25mm dial or nearest size MS pipe as per manufacturers; requirement for fuel line extension with regulator valve. v. Alternator a. Make : As Specified in the make of material list b. Type : Self exited and self regulated c. Capacity : 100KVA at 0.8PF d. System of Voltage : 3phase, 415V e. Speed : l500rpm f. Voltage regulation band : +1.00% of rated voltage g. Insulation : Class H h. AVR AVR shall be provided with a motorized or solid state potentiometer. i. IP rating of enclosure : IP 23 j. Waveform distortion : No load ; 1.5%, non- distorting, balanced Linear load ;5% k. Telephone interference : Better than 50 1. Total harmonic factor : Better than 2% Standard control panel with 160A 4 pole, 35KA MCCB .The characteristics of the DG set shall be such as to operate them in parallel mode. Routine tests as per relevant ISS shall be conducted and test reports of the same shall be furnished at the time of delivery. vii. Fuel tank. Integral type fuel tank of adequate capacity . viii. Battery: Required number of suitably rated fully charged battery with leads and terminals as required as per manufacturers? requirement;ix and separate battery charger for charging from KSEB supply. Operation manual, service manual, list of spares etc x. Acoustic Enclosure a. The DG set shall be supplied along with specially designed, company fabricated (to be fabricated in the same company from where the DG set is delivered) acoustic enclosure to meet the stringent MOEF/CPCB norms ." "b. Sufficient space and clearance shall be maintained inside the enclosure to have optimum serviceability. c. Air inlet louvers shall be designed in such a way as to operate the set at rated load even at 50 degree Celsius enclosure temperature. d. The enclosure shall be with UV resistant powder coating capable to withstand extreme environment. e. Hardware used shall be of only stainless steel make. f. Insulation material shall conform to IS 8183 specifications for better attenuation. xi. Documents to be supplied. a. Engine manual. b. Spares parts book c.Warranty certificate d. Alternator manual & test certificate 1 set control wiring drawing
xii. Installation It shall be installed in the pre-constructed concrete bed complying to relevant IS standards, IE rules and as per the direction of the departmental officials. xiii. Testing and Commissioning The DG set shall be tested as per relevant IS standards. Block load testing shall also be conducted. The DG should have capacity to withstand blocked load of at least 55%.Droop characteristics shall also be tested and adjusted for enabling parallel operation. The load 1 required for testing shall be made available at site by the selected agency at his own expenses. xiv. Warranty During the 3 year Guarantee period comprehensive maintenance (including all consumables)) and services as per manufacture recommendation and repairs shall be arranged from date of commissioning. The DG shall comply CPCB IV + norms. During the Defect liability period, the contractor should carry out on his expense, the periodic servicing as per manufactures instruction, including supply of necessary consumables such as oil, gaskets, filters etc | 1 | each | 14,00,000 ₹14 L |
| 1.00 | OD194583/2023-2024:Supply and providing following size M. S. pipe - 5mm thickness complete with suitable size 12mm flange coupling with minimum 4/5mtr using allied packing with MS bolt with washer and rising the same on the wall/ parapet using chain pullies, scaffoldings, supports with M.S angles/channels etc. including painting the pipe with one coat of zinchromate primer over a coat of high temperature resistance alu. paint etc. for extending the exhaust pipe of the newly errected D. G. sets. 80 mm dia or nearest size B class MS pipe | 24 | metre | 4,000 ₹96,000 |
| 1.00 | OD124503/2025-2026:Supply and filling diesel to the generator set as instructed by the departmental staff at site | 200 | Litre | 125 ₹25,000 |
| 1.00 | OD124507/2025-2026:Supply and fixing of Automatic Transfer switch with Controllers (ATS) for motorised change over with wire harness in the existing panel board and giving connection. | 1 | each | 50,000 ₹50,000 |
| 1.00 | OD137759/2025-2026:Steel reinforcement for RCC Work including straightening, cutting, bending, placing in position
and binding all complete | 120 | kg | 75 ₹9,000 |
| 1.01 | 14.1:Excavation for foundation in soft soil including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metres. | 6 | cum | 500 ₹3,000 |
| 1.01 | 14.7:Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required. | 4 | cum | 10,000 ₹40,000 |
| 1.01 | 90.14.1.2:Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623.
Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 1.6mm CRCA sheet, powder coated (excluding base frame) | 14.9 | sqm | 2,600 ₹38,740 |
| 1.01 | 90.14.2.1:Supply and providing 2mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc. | 0.7 | sqm | 3,500 ₹2,450 |
Tender Value
Refer Docs
EMD Value
₹50,000
Closing Date
25 Oct 2025, 6:00 pmClosed
Executive Engineer
Executive Engineer PWD Electrical Division Thrissur
DEPOSIT Developing the facilities of Hospitals and Healthcare institutions in Tribal Coastal and remote areas SITC of 100KVA Generator and HT Cabling works at GTSH Kottathara Attappady PalakkadElectrical work General Electrical Work
2025_PWD_804593_2
PWD/BLDG/9483/2025-2026
Open Tender
Electrical Works
60 days
Kottathara
Please refer Tender documents.
9 documents required · 9 mandatory
₹2,760
₹50,000
Yes
20 Jan 2026
16 Oct 2025
27 Oct 2025
16 Oct 2025
25 Oct 2025
16 Oct 2025
Work Name:DEPOSIT-Developing the facilities of Hospitals and Healthcare institutions in Tribal, Coastal and remote areas-SITC of 100KVA Generator and HT Cabling works at GTSH Kottathara, Attappady, Palakkad-Electrical work-General Electrical Work
g the 3 year Guarantee period comprehensive maintenance (including all consumables)) and services as per manufacture recommendation and repairs shall be arranged from date of commissioning. The DG shall comply CPCB IV + norms. During the Defect liability period, the contractor should carry out on his expense, the periodic servicing as per manufactures instruction, including supply of necessary consumables such as oil, gaskets, filters etc eachSOD194583/2023-2024:Supply and providing following size M. S. pipe - 5mm thickness complete with suitable size 12mm flange coupling with minimum 4/5mtr using allied packing with MS bolt with washer and rising the same on the wall/ parapet using chain pullies, scaffoldings, supports with M.S angles/channels etc. including painting the pipe with one coat of zinchromate primer over a coat of high temperature resistance alu. paint etc. for extending the exhaust pipe of the newly errected D. G. sets. 80 mm dia or nearest size B class MS pipemetrerOD124503/2025-2026:Supply and filling diesel to the generator set as instructed by the departmental staff at siteLitreºOD124507/2025-2026:Supply and fixing of Automatic Transfer switch with Controllers (ATS) for motorised change over with wire harness in the existing panel board and giving connection.OD137759/2025-2026:Steel reinforcement for RCC Work including straightening, cutting, bending, placing in position and binding all completekgè14.1:Excavation for foundation in soft soil including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metres.cumË14.7:Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required.¨90.14.1.2:Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623. Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 1.6mm CRCA sheet, powder coated (excluding base frame)sqm90.14.2.1:Supply and providing 2mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.90.14.3.3:Supply and providing heavy duty 'A' section neoprene gasket in the panel boardSupply and providing 'U' section PVC beeding in the panel board90.14.4:Supply and fabrication conveyance and installation of base frame of panel board using 75 x 40 mm rolled steel channel (ISMC)´90.14.6:Supply and providing copper bus bars including finger type SMC bus bar supports in the bus chamber, suitable size nut & bolt, providng heat shrink sleeves etc. as required.Cum [email protected]:Supply and providing copper earth bus in the panel board{90.14.10.7:Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.160A, 35/36 kA (Ics=100%Icu), 3 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 - 100% having adjustable OL & SCno|90.14.10.14:Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.250A, 35/36 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 - 100% having adjustable OL & SCo90.14.10.3:Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 16 kA (Ics=100%Icu), 4 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL]90.14.11.12:MCCB AccessoriesSupply and fixing shunt release for all voltage range up to 630A.¡90.14.11.13:MCCB AccessoriesSupply and fixing rotary handle, External type (including BUC handle with door interlock ) in the existing MCCB of rating up to 250 Ag90.14.11.2:MCCB AccessoriesSupply and fixing one number earth fault Relay up to 125A to 200A with CBCT.g90.14.11.3:MCCB AccessoriesSupply and fixing one number earth fault Relay up to 250A to 400A with CBCT.OD157556/2025-2026:Supply and providing Spreader/terminal adapter kit/ extended terminal for 3 pole MCCB rating 100A (6 Pcs)setOD157557/2025-2026:Supply and providing Spreader/terminal adapter kit/ extended terminal for 4 pole MCCB rating 100A (8 Pcs)OD157558/2025-2026:Supply and providing Spreader/terminal adapter kit/ extended terminal for 3 pole MCCB rating 160A (6 Pcs)OD157559/2025-2026:Supply and providing Spreader/terminal adapter kit/ extended terminal for 4 pole MCCB rating 250A (8 Pcs)ð2.1.2:Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.63 Amp TP & NeOD191784/2023-2024:supply and fixing Red , Yellow & blue colour LED indicator, AC/DC, as requiredcOD191790/2023-2024:Supply & fixing 250/ 5 A, 5 VA, tape wound metering CT of accuracy class 0.5rOD191786/2023-2024:supply and fixing Digital Multifunction meter to read: V, A, F, PF-3 phase accuracy class 1 LEDLOD137758/2025-2026:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured copper power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 4 core 2.5 sq mm with factory made clampC90.12.7.1:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 4 sq mm with factory made clamp·1.17.1:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.1 x 1.5 sq. mmàOD80995/2025-2026:Supply and laying of the following sizes of B class GI pipe laid 0.6 m below ground level including excavating trench of suitable size and refilling etc, as required.100 mm dia. G.I. pipe (medium class)~90.12.10.6:Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation110/94 mm or nearest size090.12.7.34:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 185 sq mmê9.1.27:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor ca
/ PVC conduit as required.9 x 1.5 sq. mm¶1.17.33:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.6 x 6 sq. mm¸1.17.12:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm¸1.17.15:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.6 x 2.5 sq. mm¶1.17.24:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.6 x 4 sq. mmª90.16.1.3:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)90.16.5.3:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)fOD191919/2023-2024:Supply and providing of 25x3 mm brass bolt with hexagon /square head nut and washerõ5.4:Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.k5.15:Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.M90.16.3.2:Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run)25 x 3 mm GI strip#5.9:Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)POD196053/2023-2024:Supply and providing 9 Litre capacity GI Fire Bucket painted in post office red with primer coat of red oxide and written with white paint 'FIRE' mounted on MS angle frame work/ wall bracket filled with fine sand, painting the bracket/ floor stand including making good the damages, colour washing etc. as requiredzOD196055/2023-2024:Supply and providing First Aid Chart duly framed and placed in a conspicuous location for clear vision.OD196056/2023-2024:Supply and providing 2mm thick Elastomeric fire retardent insulating mat as per IS 15652/2006 to withstand 3.3 KV dielectric strength90.6.4.64:Supply and drawing 650/1100 V grade FRLS PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.16.00 sq.mm 6 Run?90.9.2.1:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.100 x 50 mm CMS with base and lid!90.9.2.8:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.End cap~1.28.2:Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module~1.28.4:Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.6 Module~1.28.5:Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.8 Module090.9.2.14:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.8 module mounting boxÁOD143722/2025-2026:Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required :-FP enclosure for independent mounting of MCB/ RCCB/ RCBO©1.27.2:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)º1.24.1:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch»1.24.3:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switchÆ1.24.4:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outletÈ1.24.5:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet\OD137756/2025-2026:Copying charges o electrical/fire drawing per A3 sheet additional copies _OD137757/2025-2026:Charges for preparation of Electrical / fire drawing per A3 sheet first copy
stage.html
html • 0.03 MB
tech_eval.pdf
fin_eval.pdf
aoc.pdf
finance_1353266.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Tendernotice_1.pdf
PDF • 0.29 MB
Tendernotice_2.pdf
PDF • 0.02 MB
Tendernotice_3.pdf
PDF • 0.12 MB
Tendernotice_4.pdf
PDF • 0.15 MB
BOQ_1353266.xls
BOQ • 0.37 MB
NIT2.pdf
Tender Documents • 0.02 MB
SBD2.pdf
Tender Documents • 1.63 MB
Download all tender documents and submit your bid