CONSTRUCTION OF TOILETS, PROVN OF BIRD PROOF NET FOR SUN SHELTERS AND CERTAIN MAJOR REVENUE AND MINOR WORKS OF EM AT AF STN JODHPUR

Amount

Demolition of stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified & directed by the Engineer-in-Charge.

Dismantling Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified & directed by the Engineer-in-Charge.

Dismantling old unservicable water tanks of capacity exceeding 250 ltrs but not exceeding 500 ltrs complete all as specified & directed by the Engineer-in-Charge.

Taking up or down steel tubing of 15 mm bore pipe and connection including cleaning for re-fixing or removal to store complete all as specified & directed by the Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) not exceeding 1.5 sqm complete all as specified & directed by the Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified & directed by the Engineer-in-Charge.

Excavation in trenches in soft/loose soil, not exceeding 1.5m wide and not exceeding 1.5 in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc not exceeding 10 sqm on plan and getting out complete all as specified and directed by the Engineer-in-Charge.

Material & labour for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation, filling in and mass concrete complete all as specified & directed by the Engineer-in-Charge.

Material & labour for pre-cast cement concrete block masonry (1:3:6), type C-1 (using 20mm crushed stone graded aggregate), with solid blocks, exceeding 10cm in width and setting in cement mortar 1:6 complete all as specified & directed by the Engineer-in-Charge.

Material & labour for RCC M-25 design mix (using 20 mm graded aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified & directed by the Engineer-in-Charge.

Material & labour for RCC M-25 design mix (using 20 mm graded aggregate) in columns, pillars, piers, posts and struts complete all as specified & directed by the Engineer-in-Charge.

Material & labour for RCC M-25 design mix (using 20 mm graded aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified & directed by the Engineer-in-Charge.

Material & labour for RCC M-25 design mix (using 20 mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed by the Engineer-in-Charge.

Material & labour for formwork to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits of foundation & plinth beams; and similar work; verticle or to batter, for flat rough finished surfaces of concrete complete all as specified & directed by the Engineer-in-Charge.

Material & labour for formwork to sides of pillars, posts, struts, piers,columns, and stanchions; for rough finished surfaces of concrete, circular on plan complete all as specified & directed by the Engineer-in-Charge.

Material & labour for formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc, for flat rough finished surfaces of concrete complete all as specified & directed by the Engineer-in-Charge.

Material & labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping), for flat rough finished surfaces of concrete complete all as specified & directed by the Engineer-in-Charge.

Material & labour for TMT Bars 10 mm dia & over, cut to length, bent to shape required, including cranking, binding spirally for hooping for columns, hooking ends & binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified & directed by the Engineer-in-Charge.

All as per item Ser No 18 above but 8 mm dia bars as in stirrups.

Material & labour for rendering 15mm thick on PCC block masonry surfaces or surface other than fair face of brickwork in cement mortar (1:4), finished even & smooth (without using extra cement) complete all as specified and as directed by the Engr-in - Charge.

Material & labour for rendering 15mm thick on PCC block masonry surfaces or surface other than fair face of brickwork in cement mortar (1:6), finished even & smooth (without using extra cement) complete all as specified and as directed by the Engr-in - Charge.

Material & labour for rendering 5mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:3) as in ceiling complete all as specified and as directed by the Engr-in - Charge.

Material & labour for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint, white or tinted complete all as specified and as directed by Engineer-in-Charge.

Material & labour for preparing plastered or un-plastered new surfaces of wall and applying three coats of white wash complete all as specified & directed by the Engineer-in-Charge.

Material & labour for preparing plastered or un-plastered new surface and applying three coats of white wash on ceiling surface complete all as specified & directed by the Engineer-in-Charge.

Material & labour for hardcore with broken stone or boulders of gauge exceeding 63mm but not exceeding 100mm , deposited , spread and levelled in layers not exceeding 15cm thick, watered, rolled and rammed to a true surface complete all as specified and directed by Engr-in-Charge.

Material & labour for 75 mm thick, PCC 1:4:8, type D-2, (using 40 mm graded crushed stone aggregate), as in sub base of floor’s complete all as specified & directed by the Engineer-in-Charge.

Material & labour for 75mm thick PCC 1:3:6, type C-2, (using 40mm graded crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified & directed by the Engineer-in-Charge.

Material & labour for Glazed Vitrified tiles (GVT) of size 800mm x 800mm x 10 -12 mm (Non skid/Matte) (square) as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, over & including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed by Engr-in-Charge.

Material & labour for Glazed Vetrified tiles (GVT) glossy of size 600mm x 300mm x 10 -12 mm in vertical surfaces as in skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, over & including 10mm thick rendering in cement mortar (1:4) complete all as specified and as directed by Engr-in-Charge.

Material & labour for pre polished granite stone (of any type) tiles 20mm thick machine cut, bedded in steps/platform/floors & jointed with grey cement slurry & pointed with white cement with admixure of pigment to match the shade of granite stone including cutting & polishing over and including 20mm thick screed in cement mortar (1:6) complete all as specified & directed by the Engineer-in-Charge.

Material & labour for rounding to edges of stone slab one edge, such as in steps, platform and other similar situations complete in all respect and as directed by Engineer-in-Charge.

Supply & fixing powder coated aluminium frame for doors, windows ventilators (minimum thickness of powder coating 50 micron), with one or more rebates including joining cleat for fixing etc. complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing MDF board (Medium Density Fibre board) 20mm thick decorative type with decorative face veneer on both faces, fixed with screws to timber frame-work or fixed with aluminium frame complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing aluminium 4 levers Mortice lock, vertical type, size 75mm complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing cast type anodised powder coated aluminium handles 150mm long complete all as specified and directed by the Engineer-in-Charge.

Supply & fixing 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type B-21 complete all as specified and directed by the Engineer-in-Charge.

Supply & fixing powder coated Aluminim anodised barrel tower bolt 150 mm long extruded section complete all as specified & directed by the Engineer-in-Charge.

Material & labour for 300mm length Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed by the Engineer-in-Charge.

Material & labour for 16 mm outer dia 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stablized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and as directed.

Material & labour for 20 mm outer dia 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stablized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and as directed.

Supply & fixing PTMT waste coupling for 32 mm dia discharge pipe (half or full threaded) [Minimum weight for 32 mm – 45 gms] complete all as specified and as directed

Supply & fixing angle valve with wall flange complete all as specified & directed by the Engineer-in-Charge. Make Jaquar Cat No. OPP-15053PM / Somany Cat No SKU : 272211140041 / Parryware Cat No G3153A1.

Supply & fixing bib cock 2 way with wall flange complete all as specified & directed by the Engineer-in-Charge. Make : Jaquar Cat No. OPP-15041PM / Somany Cat No SKU : 210740051 / Parryware Cat No G3167A1.

Supply & fixing swan neck pillar cock complete all as specified & directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : SDL297286096 / Somany Cat No : C210910 / Parryware Cat No G3121A1.

Supply & fixing corner glass shelf 300 mm (with brass brackets) complete all as specified & directed by the Engineer-in-Charge. Make Prayag Cat No. BEA-44 or equivalent of Jaquar/ Hindware / Parryware / Cera as approved by GE.

Supply & fixing 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls or laid in trenches/ floors complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls or laid in trenches/ floors complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing PVC (SWR) bend any radius of 75 mm bore complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing PVC (SWR) bend any radius of 110 mm bore complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 110mm bore PVC (SWR) vent cowl complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 75mm dia outlet PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and as directed.

Supply & fixing PVC (SWR) gully trap 100/110 mm, setting and jointing with solvent cement complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing CP grating doom 125mm dia. with waste hole (minimum weight 40 gms) complete all as specified and as directed.

Supply & fixing PVC connection 15 mm size with brass nuts, of length 600 mm complete all as specified & directed by the Engineer-in-Charge. Make : Prayag Cat No. BCT-04 / or equivalent cat part of Cera / Hindware / Parryware / Jaquar as approved by GE.

Supply & fixing carmina Vitreous China Urinal, Flat back stall type, ivory of size 420 x 395 x 635 mm complete all as specified & directed by the Engineer-in-Charge. Make : Cera Cat. No. S4020102 / Hindware Cat No : 60023 / Jaguar Cat No : URS-WHT-132530.

Supply & fixing Urinal spreader of PTMT any colour for fixing with 15mm dia pipe (min. weight 60gms) complete all as specified and as directed by Engr-in-Charge.

Supply and fixing One Piece English Water closet having Dimensions 700mm x 370mm x 645 mm with Soft Close Seat Cover and Twin Flush Fittings with wall-mounted closet and concealed S or P Trap , Ivory colour , Product Code: CERA-CLOVER-S1013115 / Hindware Cat No : 92547 (S-22) / Jaguar Cat No : CNS-WHT-851S300SPP.

Supply & fixing counter type wash basin of size 570mm x 450mm dia of colour ivory compete all as specified and directed by the Engineer-in-Charge. Make : Cera Cat No S2030136 / Hindware Cat No 10017 / Grohe Cate No 39423000.

Supply & fixing rotational moulded polyethylene water storage tank of capacity 1000 litre (Cylindrical vertical with closed top), triple layer construction, ISI marked, hoisted & fixed in position complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing Towel Rack 600 mm complete all as specified & directed by the Engineer-in-Charge. Make : Cera Cat No. F5006101 / Hindware Cat No : F870009 / Jaguar Cat No : CAN-1181S

Supply & fixing 20 mm dia bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe, [Minimum weight for 20 mm – 210 gms] complete all as specified and as directed Make Prayag cat No. 152 or equivalent cat part of Cera / Hindware / Parryware / Jaquar as approved by GE.

Supply & fixing liquid soap dispenser complete all as specified & directed by the Engineer-in-Charge. Make : Prayag Cat No. BA -33 / Cera Cat No F5007111 / Jaguar Cat No AKP-35735P.

Supply & fixing sensor Hand Dryer complete all as specified & directed by the Engineer-in-Charge. Make : Prayag Cat No. BSD-18 / Cera Cat No B2220102 / Jaguar Cat No HDR-WHT-M04A.

Supply & fixing cast iron body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851mm to 1000 mm in width & of weight between 61kg to 80kg complete all as specified and as directed. complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing Health Faucet ABS body with 1 meter SS braided connection pipe & wall hook complete all as specified and directed. Make: Cera Cat No. F8030109AB / Jaguar Cat No ALD-565 / Somany Cat No SKU:272150680041

Supply & fixing toilet paper Holder complete all as specified & directed by the Engineer-in-Charge. Make: Prayag Cat No. BA-08 or equivalent cat part of Cera / Hindware / Parryware / Jaquar as approved by GE.

Supply & fixing in repairs squatting Pan, ivory of size 450mm x 350mm x 100 mm complete all as specified & directed by the Engineer-in-Charge. Make : Cera Cat. No. S4040101 / Hindware Cat No : 60003 / Parryware Cat No : C0573

Supply & fixing glass shelf 500x125mm(with brass brackets) complete all as specified & directed by the Engineer-in-Charge. Make : Prayag Cat No. BEA-45 or equivalent cat part of Cera / Hindware / Parryware / Jaquar as approved by GE.

Supply & fixing collapsible Waste pipe 800 mm long complete all as specified & directed by the Engineer-in-Charge. Make Make Prayag Cat No. 3272 or or equivalent cat part of Cera / Hindware / Parryware / Jaquar as approved by GE.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soil complete all as specified & directed by the Engineer-in-Charge.

Removing excavated materials (soils) to a distance exceeding 250 mtr but not exceeding 500 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified & directed by the Engineer-in-Charge.

Surface excavation not exceeding 30cm deep & averaging 15 cm deep and getting out in soft / loose soil complete all as specified & directed by the Engineer-in-Charge.

Material & labour for 100 mm thick, PCC 1:4:8, type D-2, (using 40 mm graded crushed stone aggregate), as in floors complete all as specified & directed by the Engineer-in-Charge.

Material & labour for factory made 10mm thick Vitrified heavy Duty parking tiles coloured, matt finish, unglazed and unpolished, of size 300mm x 300mm over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified & directed by the Engineer-in-Charge.

Material & labour for precast cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone agg), solid blocks or Kerb stone of 150mm thick ( 300mmx300mmx150mm ) with plain or interlocking joints set in cement mortar 1:4 complete all as specified & directed by the Engineer-in-Charge.

Material & labour for applying two coats of synthetic enamel paint over a coat of primer on brick, stone, concrete, asbestos cement or plaster surface of any description over 10cm girth or width, not otherwise described including preparation of new surface complete all as specified & directed by the Engineer-in-Charge.

Excavation in trenches in hard/dense soil, not exceeding 1.5m wide and not exceeding 1.5 in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc not exceeding 10 sqm on plan and getting out complete all as specified and directed by the Engineer-in-Charge.

Material & labour for cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in bed to drain pipes of size 150 mm bore, including packing under & haunching against the sides of pipes after they are laid and tested complete all as specified and directed by the Engineer-in-Charge.

Material & labour for Reinforced concrete pipes 100mm dia, class NP2, laid & jointed complete with collars complete all as specified and directed by the Engineer-in-Charge.

Material & labour for construction of new stone masonry soakage well 1.8 metres dia and 3.0 metres effective depth complete all as shown on drg No CEAA/TD/80 SHEET 1/2 & 2/2 and as specified & directed by the Engineer in Charge.

Material & labour for wire netting stainless steel wire 0.91 mm dia and size of mesh 20 mm appartue fixed with tinned tacks of stainless steel wire staples complete all as specified & directed by the Engineer in Charge.

Material & labour for flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., & similar work conforming to Fe 290 Grade E-165 complete all as specified & directed by the Engineer in Charge.

Material & labour for site clearance by cutting all bushes, shrubs, any type of vegetation etc and removing to a distance exceeding 500 meter but not exceeding 1500 meter outside MD land complete all as specified & directed by the Engineer in Charge.

Dismantling posts or struts (steel or R.C.C.) any section, including taking out embedded portion in concrete and making good disturbed ground complete all as specified and directed by the Engineer-in-Charge.

Dismantling GI plain/barbed wire any description complete all as specified and directed by the Engineer-in-Charge.

Dismantling fencing wire mesh any type complete all as specified and directed by the Engineer-in-Charge.

Material & labour for squared rubble walling, Jodhpur type, brought to courses and regular coursed, curved on plan to a mean radius not exceeding 6m, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed by the Engineer-in-Charge.

Material & labour for cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone agg), in cills, steps, seismic and other similar bands, copings, bed plates, including necessary formwork and weathering, slightly rounded or chamfered angles and throating complete all as specified & directed by the Engineer-in-Charge.

Material & labour for rendering 15mm thick on stone masonry or surface other than fair faces of brickwork fair faces of brick work in CM (1:4) and finishing the surface even and fair with using extra cement complete all as specified and as directed by the Engr-in - Charge.

Supply and fixing mild steel angle iron (Fe-310) as in posts, struts, flat iron (securing wire mess etc) in fencing including cutting top to shape required, drilling holes, notching for wire, erect and fixed in true position etc complete all as specified and as directed by the Engr-in - Charge.

Supply and fixing galvanised chain link fencing, any size or type including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed by the Engineer-in-Charge

Supply only MS screw, bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexgonal or square nut exceeding 50 mm but not exceeding 100 mm long complete all as specified and directed by the Engineer-in-Charge

Material & labour for preparation of brick masonry/concrete wall surfaces, plastered/unplastered and applying two coats of exterior weather proof water base emulsion paint over a coat of primer of same make on walls (make:- Shalimar- shaktiman/ Asian- ACE/ Burger- wall masta) complete all as specified and directed by the Engineer-in-Charge.

Supply & fixing in repairs Galvanized, 2 strand, steel barbed wire 2.24 mm dia., barbed with 2 mm dia., barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanized mild steel pins etc., complete all as specified and as directed by the Engr-in - Charge. Note: Each line wire to be measured for payment purpose.

Supply & fixing galvanised steel punched type concertina coil of 1050 mm dia (Dia of coil unstratched and fixed to angle iron posts/struts with 3.15 mm dia GI wire complete all as specified and as directed by the Engr-in - Charge.

Supply & fixing Fe 410-W (GdeE- 250) quality-A, Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed by the Engr-in - Charge.

Supply and fixing 300 mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed by the Engineer-in-Charge

Material & labour for preparation of new steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint (first quality) over a coat of red oxide primer complete all as specified & directed by the Engineer in Charge.

Material and Labour for point wiring for One light / fan/exhaust fan point controlled by one switch 5 Amp, SP, one way 240 volts with & using 1.5 Sqmm (nominal area) FRLS PVC insulated and unsheathed multistranded copper conductor cable 1100 volts grade drawn through and including 20mm dia medium grade rigid PVC conduit (concealed) (ISI marked) with all accessories including surface/concealed sheet steel terminal/ CI box with 3 mm thick hylam / masonite sheet top cover including 1.5 Sqmm size PVC insulated unsheathed copper conductor multistranded cable for continuous earth conductor to common earth and connecting to earth dolly, complete all as specified and directed by the Engineer-in-Charge.

All as per item No 102.00 above but one 5 Amp 3 pin socket outlet on independent board with other switches complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing modular white cover plate with frame, 8 module complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing modular switches 6 Amps, 01 module, single pole, one way complete all as specified and directed by the Engineer-in-Charge

Supply and fixing socket 6A 2/3 pin combined 02 module complete all as specified and directed by the Engineer-in-Charge

Supply and fixing MCB 6 to 32 Amps SP 10 KA 'C' series complete all as specified and directed by the Engineer-in-Charge

Supply and fixing MCB 40 Amps SPN 10 KA 'B' series complete all as specified and directed by the Engineer-in-Charge

Supply and fixing ceiling rose polycarbonate, isolated body 65mm x50 mm , 2 to 3 terminal complete all as specified and directed by the Engineer-in-Charge

Material and Labour for point wiring with 15 Amps switch socket using 2.5 Sqmm (nominal area) FRLS PVC insulated and unsheathed multistranded copper conductor cable 1100 volts grade drawn through and including 20mm dia medium grade rigid PVC conduit (concealed) (ISI marked) with all accessories including surface/concealed sheet steel terminal/ CI box with 3 mm thick hylam / masonite sheet top cover including 1.5 Sqmm size PVC insulated unsheathed copper conductor multistranded cable for continuous earth conductor to common earth and connecting to earth dolly, complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing modular white cover plate with frame, 3 module complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing modular switches 16 Amps, 01 module, one way complete all as specified and directed by the Engineer-in-Charge

Supply and fixing socket 6A/16A, 2/3 pin combined 02 module complete all as specified and directed by the Engineer-in-Charge

Supply and fixing factory made MCB DB SPN 06 way 240 V with double door, IP 43 protection, having 200 Amps 02 nos bus bar for neutral bar and earth bus bar with MCB SPN 'C' curve type 40 Amps-01 no, MCB SP 'C' curve type 06 to 32 Amps-04 nos fixed/ concealed in wall complete all as specified and directed by the Engineer-in-Charge.

Supply & fixing exhaust fan AC single phase 230/240 V, of size 300 mm sweep with louver complete all as specified and directed by the Engineer-in-Charge.

Material and Labour in repairs for earthing complete with galvanised steel earth electrode 60cm x 60cm x 6mm buried directly in ground vertically to depth not less than 2.25m below normal ground level with top edge of the earth plate at a depth not less than 1.5m below ground level connected to and including GI earth lead wire 4mm dia by means of nuts, bolts, check nuts and washer etc, made of GI and connected to test point and earth dolly all as shown in electrical plate No. 3 SSR Part-I 2009 and specified or indicated including excavation and earthwork in any type of soil PCC (1:3:6) Type C1 in chamber, precast RCC 50 mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM (Weight not less than 4.00 Kg/Square metre) with PCC frame, funnel with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm bore medium grade GI protection pipe, test point etc. complete all as specified and directed. Note: - This Item includes the cost of GI earth lead and GI protection pipe up to 7.5metres. Beyond 7.5m GI earth lead and GI pipeshall be measured and paid for separately.

Removing excavated materials (soils) to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified & directed by the Engineer-in-Charge.

Material & labour for sand cushioning for PVC cable with screened & washed sand & punning to provide a required cover complete all as specified and directed by the Engineer-in-Charge. Note:- Punned thickness only shall be measured and paid.

Material & labour for stone slab 40 mm to 50 mm thick rough dressed Jodhpur stone patties/ slab cover in trenches for protection of cable 25 cm to 30 cm wide and not less than 50 cm in length laid dry abutting each other with gap between adjacent slab not exceeding 10 mm over sand cushioning complete all as specified and directed by the Engineer-in-Charge.

Supply, laying, jointing, testing and commissioning in repairs of Aluminium conductor Cable multi stranded XLPE insulated, armoured electric power cables heavy duty, 1100 volts grade, cross area sectional 10 sqmm 2 core complete all as specified and directed by the Engineer-in-Charge.

Supply & fixing 16 Watt LED tube light alongwith fixtures complete all as specified and directed by the Engineer-in-Charge.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc. removing materials to store for keeping in safe costudy or for taking credit Complete all as specified and directed by the Engineer-in-Charge.

Taking down MCB DB with MCB any type and any capacity complete all as specified and directed by the Engineer in Charge.

Taking down old unserviceable light fittings with fixtures complete all as specified and directed by the Engineer in Charge.

Taking down old unserviceable aluminium cable core complete all as specified and directed by the Engineer in Charge.

Material & labour for earthing complete with copper earth plate electrode 600mm x 600mm x 3.15 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to and including earth lead of copper strip 20mm x 3.15mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on completion and excavation and earth work in any type of strata, PCC 1:3:6 type C1 in chamber, precast RCC cover 50mm thick in cement concrete 1:2:4 type B1, reinforced with welded steel wire fabric or XPM (Weight not less than 4 Kg/Sqm) with cast iron frame, funnel with wire mesh, 20mm bore GI pipe medium grade watering pipe, lugs, 40mm bore GI pipe medium grade protection pipe up to 7.5m. Note : This Item includes the cost of copper earth lead and GI protection pipe up to 7.5metres. Beyond 7.5m copper earth lead and GI pipeshall be measured and paid for separately.

Supply and fixing Test point Terminal block made out of gun metal or Phosphorous bronze size 75mm x 75mm x 25mm drilled and screwed including 3 nos 8mm dia 25mm long hex head screw complete all as specified & directed by Engineer-in-Charge.

Supply and fixing copper strip 20x3 mm with saddles and fixing screws for connecting copper strip at surrounding, inside and outside the building complete all as specified & directed by Engineer-in-Charge.

Material and labour for Kota stone earth pit cover 2 feet x 2 feet complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing galvanised steel tubing of 15 mm dia, medium grade including fittings complete all as specified & directed by Engineer-in-Charge.

Supply and fixing 15 mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & directed by Engineer-in-Charge.

Supply and fixing 15 mm dia Self closing taps of cast iron or malleable cast iron, galvanised, screwed for iron pipe and fixed complete all as specified & directed by Engineer-in-Charge.

Supply and fixing single pointed air termination aluminium rod 12 mm dia, 300 mm long complete all as specified & directed by Engineer-in-Charge.

Supply and fixing 40mm bore galvanised steel tubing, medium grade, 1.50 metres long with MS plate welded as base for fixing of air termination rod complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing aluminium strip 25X3.15 mm with saddles and fixing screw etc for roof conductors and down conductors above ground complete all as specified and directed by the Engineer in Charge.

Material and labour for PCC block of size 150mm x 150mm x 300 mm made of PCC 1:2:4 type B1 (using 40 mm dia graded stone aggregate) for fixing/mounting of running earthing conductor complete all as specified and directed by the Engineer-in-Charge.

Material & labour for Bore Earthing in any type of soil complete , by boring the hole 50mm dia buried directly vertically in the ground with boring machine up to 50 metres depth below the ground level, using & providing earth electrode of 50mm dia GI pipe (50 metres long) medium grade duly drilled hole of 12mm dia having 15cm C/C on both side of the pipe, including lowering the GI pipe earth electrode in bore well up to the depth of 49 metres and one metre above the ground level, and including provision of 12 metre long 150mm dia MS pipe for protection of bore well buried directly vertically in the ground by boring 150mm bore with and including filling of commercial salt, charcoal dust , copper sulphate and magnesium phosphate around the pipe electrode in layers up to full depth of protection pipe (12 metres) , each layer shall be 30cms thick, and including provision of GI strip 50mm x 6mm welded to earth electrode of GI pipe up to the 10 metre below ground level and 15 metre length from the bore well to test point gun metal, and construction of PCC 1:2:4 Type B1 foundation of size 60cm x 60cm x 30cm surrounding the bore well, complete all as specified and directed by the Engineer in Charge. Note : - This Item includes the cost of GI earth lead strip up to 25 metres. Beyond 25metres earth lead shall be measured and paid for separately.

Material & labour for Bore Earthing in hard rock complete , by boring the hole 50mm dia buried directly vertically in the ground with boring machine up to 50 metres depth below the ground level, using & providing earth electrode of 50mm dia GI pipe (50 metres long) medium grade duly drilled hole of 12mm dia having 15cm C/C on both side of the pipe, including lowering the GI pipe earth electrode in bore well up to the depth of 49 metres and one metre above the ground level, and including provision of 12 metre long 150mm dia MS pipe for protection of bore well buried directly vertically in the ground by boring 150mm bore with and including filling of commercial salt, charcoal dust , copper sulphate and magnesium phosphate around the pipe electrode in layers up to full depth of protection pipe (12 metres) , each layer shall be 30cms thick, and including provision of GI strip 50mm x 6mm welded to earth electrode of GI pipe up to the 10 metre below ground level and 15 metre length from the bore well to test point gun metal, and construction of PCC 1:2:4 Type B1 foundation of size 60cm x 60cm x 30cm surrounding the bore well, complete all as specified and directed by the Engineer in Charge. Note : - This Item includes the cost of GI earth lead strip up to 25 metres. Beyond 25metres earth lead shall be measured and paid for separately.

Supply and fixing vitreous porcelain insulators on walls, roof etc complete all as specified and directed by Engr-in-charge.

Material & labour for PVC sleeve of suitable size heat shrinkable type suitable for insulation of copper strip of size 20 x 3.15 mm etc complete all as specified and directed by the Engineer-in-Charge.

Material & labour for point wiring complete with 1.5 sqmm PVC insulated FRLS copper conductor including ERW steel conduits heavy duty on surface incl all accessories like bends , tessa and jointing plate pressed steel terminal sunken boxes 2 mm thick duly electroplated with 3 mm thick plastic laminated sheet for mounting of switches sockets, regulators etc including 1.5 sqmm PVC insulated FRLS copper conductor used as earthwire for including making disturbed surface good to existing with surfaced colour for one flame proof light point/fan point controlled by one way switch complete all as specified and directed by the Engineer-in-Charge.

Supply and Fixing Flame proof-weather proof exhaust fan, single phase, 230 Volts, 50 Hz AC supply driven in cast aluminium, LM-6 body, 450mm sweep, 1440 RPM complete with terminal box with louvers and necessary flame proof flexible metallic conduit, making suitable hole including grouting of nuts and bolts complete all as specified and as directed by Engineer in Charge. Make: Flexpro / Shyam / Sudhir / Crompton Greaves

Supply and Fixing Flame proof-weather proof rotary switch Isolator 10 Amp 220 volt single phase complete all as specified and directed by the Engineer-in-Charge. Make: Flexpro / Shyam / Sudhir / Crompton Greaves

Supply & fixing Sheet metal enclosure , double door, dust protected, powder coated, SPN distribution board, 4 way, 415V with IP 54 protection , comprising of One MCB SPN 32 amps and four MCBs SP 6 to 30 amps 4 Nos and sixteen MCBs SP, ranging 6 to 32 Amps, 10 KA including fixing of DB on wall with MS clamps & necessary nuts bolts and making electric connection complete all as specified and as directed by the Engineer-in-charge.

Material & Labour for Making of opening / hole (Square or round) using diamond cutter in existing stone masonary wall of suitable size for occupying and fixing the exhaust fan of size 450mm, with & including finishing the dismantled / disturbed surfaces with cement mortar 1:4 and make the surfaces neat & tidy and also fixing the exhaust fan with necessary clamps, nuts and bolts complete all as directed by Engineer-in-charge.

Supply, Fixing, testing and commissioning of Isolation Transformer 10KVA, 01 phase, 50 HZ, AIR COOLED COPPER WOUND INDOOR type, class of insulation A, metallic body duly powder coated, designed for input voltage range 240+/- 5 % and output voltage range 240 +/- 5%, ratio 1:1, efficiency more than 95 %, potential difference between neutral to earth less than one volt, with all standard fittings complete all as specified and directed by the Engineer in Charge. Make : VOLINA/ITE / AE

ABHOG INFRASTRUCTURE PRIVATE LIMITED

Om Trading Corporation