Comprehensive maintenanceof OTM Accn of RIMC under AGE B/R-II of GE Dehradun.

Amount

Demolition of brick work or stone masonary in cement mortar including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Dismantling asbestos cement (corrugated , semi corrugated, etc.) sheets in roof coverings etc complete all as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n.exc 1.50 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.50 sqm but n.exc 4.0 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Dismantling wall and ceiling board,of any description complete all as specified and directed by Engr-in-Charge

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed

Demolition of cement concrete (un reinforced) in ground floor and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling of cast iron/ PVC /AC /SGSW pipes alongwith fittings and accessories upto 100 mm dia jointed in cement mortar and taking out of walls, floors or trenches, if required complete all as specified and directed.

Dismantling Mild Steel work of any description not otherwise provided for complete all as specified and directed by Engr-in-Charge

Taking up or down 15 mm steel tubing and connections complete all as specified and directed.

Taking up or down 20 mm steel tubing and connections complete all as specified and directed.

Dismantling of water tanks of capacity exc 250 ltrs and n.exc 500 ltrs and removing from site, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc.Laid, bedded and pointed in any mortar complete all as specified and as directed.

Taking down cement plaster of any description, thickness on brick, stone, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, removal of rubbish and cleaning, etc complete all as specified and as directed.

Taking down shutter of any description exc. 1.0 Sqm but n.exc 2.0 Sqm each and removing from site complete all as specified and directed.

Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in soft/loose soil complete all as specified and directed by Engineer-In- Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in l;ayers not exc 25 cm in soft and loose soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated material (soil) not exceeding 50M and depositing where directed at a lavel not exceeding 1.5m above the starting point, complete all as specified and directed by Engineer-in-Charge.

Material and labour for mild steel TMT bars 10mm dia and over , cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns,footing, plinth beam, roof beam, lintels, slabs and other similar structures etc., hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge

Material and labour for mild steel TMT bars 8 mm dia and over cut to length and bent to shape required and binding with mild steel wire dia not less than 0.9 mm (annealed) complete all as specified complete all as specified and directed by Engineer-In- Charge

All as per ser item no 21 here-in-above but 5mm dia and over upto and inclluding 10mm dia in stirrups, spacers and binders etc complete all as specified and directed by Engineer-in-Charge

Material and labour for 75 mm thick cement concrete type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in sub base complete all as specified and directed by Engineer-in-Charge.

Material and labour for brick work with old size fly ash bricks straight or curved on plan exc 6m mean radius built in cement motar CM 1:6 complete all as specified and as directed

Material and labour for brick work with flyash bricks straight or curved on plan in CM 1:4 as in half brick thick walls complete all as specified and as directed.

Material and labour for 15mm thick rendering on other than fair faces of brick work in CM 1 : 6 finished even and smooth without using extra cement complete all as specified and directed by Engineer-In- Charge.

Material and labour for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with water proofing compound finished even and fair without using extra cement complete all as specified and directed by Engineer-In- Charge. (Water proofing compound shall be measure and paid separatelly).

Supply only liquid water proofing compound as per manufacturer instructions complete all as specified and directed by Engineer-In- Charge.

Material and labour for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in floors, to receive surface of tile complete all as specified and directed.

Material and labour for rendering 10mm thick on other than fair face of brick work surfaces in CM 1:4 for fixing of tiles, complete all as specified and directed.

Material and labour for screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/ tiles complete all as specified and directed.

Material and labour for screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:6, for laying floor finishes/ tiles complete all as specified and directed.

Material and labour for glazed coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, on floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Material and labour Glazed ceramic tiles coloured 450 x 350mm, 300mmx 450mm , 7 to 8 mm thick, set and jointed on vertical surface in neat cement slurry and pointed in white or colour cement to match etc complete all as specified and and as directed

Material and labour for cement concrete 1:2:4 type, B1 using 20 mm graded stone aggregates as in copings, roof padding/staging of water tank etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed

Material and labour for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beamschullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified and directed.

Material and labour 18 to 20mm thick granite(Zed Black colour as approved by GE) stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform/dado/skirting /plateform counter top WHB in cluding cutting holes for oval shape /urinal partitions etc. including 15 mm thick cement screed bed 1:6 CM in horizontal or vertical surfaces including grinding the edges half round and polishing complete all as specified and directed by Engineer-In- Charge.

Material and labour cutting chases, pinning in, making good to facing where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting not exc 10cm girth complete all as specified and directed.

Supply and fix medium grade galvanized steel tubing with all fittings &fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and as directed

Supply and fix medium grade galvanized tubing with all fitting fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length), complete all as specified and as directed

Supply & fixing factory made single extruded WPC(Wood polymer composite) Solid door frame/ chowkat of size 100X50 comprising of virign PVC polymer of K value 58-60 (suspension grade ) calcium corbonate and natural fibers ( wood powder/rice husk /wheat husk) and non toxic additives (max toxicity index of 12 to 100 gms) fabricated with mitred joints and applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of750Kg/cum screw withdrawal strength of 2200 N (face) & 1100 N edge,minimum compressive strength of 58 N/mm2, moduus of elasticity 900N/mm2 and resistance to spread of flame of class 'A' category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in postion with SS dash fasterns / hold fast of required dia and length,colour of door frame to match that of shutter all as specified and directed.

Supply and fix factory made single extruded WPC (Wood polymer Composite) Solid moulded Flush Door Shutter of 30 mm size comprising of virgin PVC resin of K value 58-60 (Suspension Grade), Calcium Carbonate and natural Fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives (max toxicity index of 12 for 100 gms) having min density of 650 Kg/Cum and screw withdrawal strength of 1800 N (Face) &900 N (Edge) Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category with property of being Termite/ Borer proof. Water/ Moisture Proof, Fire retardant and fixing with stainless steel but hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer - in- Charge, Materia test certificate and authentication should be compulsory provided by the manufacturing company.

Material and labour PCC 1:3:6 Type C 0 using 12.5 mm graded stone aggregate) for filling back of door chowkhats complete all as specified and directed by Engr-in Charge

Supply and fix Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed.

Supply and fix in repair stainless steel sink with drainage board 1.00mm thick for kitchen with plug/waste pipe washers including cantiliver bracket or, connecting unions etc over all size 915 x 460mm with bowel size 410mm x 330mm x 160mm complete all as specified and as directed.

Supply and fix 2nd class 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Supply and fix 2nd class Hard wood 35 mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and as directed.

Supply and fix 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

Supply and fix Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

Supply and fix Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

Supply and fix in repair galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

Supply and fix in repir floor door closer huydralic type for door of weight approx 30 kg to 65 kg incl taking out old closer and fixing of new door closer incl removal of shutter and refixing it at same position incl making good of disturbed area complete all as specified and as directed.

Material and labour for welding in repairs n. exc 2.5cm in length thickness of metal exc 9mm and not exc 20mm complete all as specified and as directed.

Material and labour for welding in repairs exc 2.5cm but not exc 5cm in length thickness of metal exc 9mm and not exc 20mm complete all as specified and as directed.

Supply and fix Aluminium alloy, anodised, sliding door bolt size 300 mm with hasp, staple (bolt ype) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed. Complete all as specified and directed by Engr-In-charge.

Supply and fix 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed.

Supply and fix aluminium anodised tower bolt 150 mm long of extruded section etc complete all as specified and as directed.

Supply and fix in repair aluminium alloy, anodised, sliding door bolt size 300 mm with hasp, staple (bolt ype) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engr-In-charge.

Supply and fix in repair 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed.

Supply and fix in repair aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed.

Supply and fix in repair aluminium anodised tower bolt 125 mm long of extruded section etc complete all as specified and as directed.

Supply and fix in repair continous (piano) hinges of 40mm width of flaps when open mild steel bright finish or electroglavanised complete all as specified and directed.

Supply and fix in repair floor door stopper 150mm overall length of cover plate of aluminium alloy body and tongue anodised with hard drawn steel spring fixed to floor complete all as specified and directed.

Supply and fix in repair door closer gydraulically regulated designation No 3 universal type suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 Kg of Aluminuim die cast body complete all as specified and directed.

Supply and fix in repair mild steel 300mm ordinary rat and tail pattern springs including roller and roller plate complete all as specified and as directed.

Material and labour for 75mm thick PCC 1:3:6 type C-2, (20 mm graded stone aggregate)as plinth protection and finishing even and smooth without using extra cement incl making joints 12 mm wide of full depth of PCC at every 3 meters and at every change in direction and filling the same with sealing compund grade 'A' incl necessary formwork. Complete all as specified and directed.

Material and labour for forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ for thickness of 75mm complete all as speicified and directed.

Supply and fix 500 litre rotational moulded tripple layer polyethlene water storage tanks white colour (cylindrical vertical with closed top) and suitable size of MS tasla with locking system hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

Supply and fix 20mm ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed.

Supply and fix in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20 mm bore complete all as specified and as directed.

Supply and fix vitreous China corner wash hand basin, 400 mm x 400 mm x 125 mm size including 15mm dia CP brass waste coupling, 450 mm long HDPE PVC connection, 750 mm long 32mm bore HDPE waste down pipe including CI brackets complete all as specified and directed.

Supply and fix in repair Brass CP wall mixer 15 mm bore (wall mounted type) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed.

Supply and fix in repair fancy type 125mm size square brass CP shower rose with or without swivel joints complete all as specified and as directed.

Supply and fix brass chromium plated bottle traps for wash basins, urinals with inlet and outlet screwed for pipe or connections inclding necessary packing union and cap and fixed complete all as specified and directed.

Supply and fix in repair bib tap long body fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed.

Supply and fix in repair stop valves/angle valves fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed for 15 mm dia bore pipe complete all as specified and as directed.

Supply and fix in repair tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and as directed.

Supply and fix in repair PVC connection of 30 cm length including brass nuts complete all as specified and as directed.

Supply and fix in repair PVC connection of 45 cm length including brass nuts complete all as specified and as directed

Supply and fix fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed.

Supply and fix fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with fancy type screws complete all as specified and directed.

Supply and fix in repairs vitreous china squatting pan orissa pattern long pan size 580 mm x440mm white with spun pipe ‘P’ or ‘S’ trap, front or back inlet and foot rests excluding flushing cistern & flush pipe but incl. cement concrete bedding fixed complete all as specified and as directed.

Supply and fix in repair vitreous china wash down water closet pan (pedestal pattern) with 'P' or 'S' trap white, including connection to drain or out going pipe and flush pipe anti symphonize pipes etc complete all as specified and directed.

Supply and fix in repair plastic water closet seat, of white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device for pedestal pan complete all as specified and directed.

Supply and fix in repair flushing cistern internal unit for high or low level flushing cistern including cistern for wall hanging petstal pan of 10ltr capacity as per the direction complete all as specified and directed.

Supply and fix high density polyethylene (HDPE) pipe of pressure 6kgf.sq.m of 32mm dia fixed complete all as specified and directed.

Supply and fix high density polyethylene (HDPE) pipe of pressure 6kgf.sq.m of 40mm dia fixed complete all as specified and directed.

Supply and fix in repair brass spindal Half / full turn for HWB mixture or wall mixture incl washer fixed as per the direction complete all as specified and directed.

Supply and fix in repair PVC low level flushing cistern 10 litres, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe for pedestal pan complete all as specified and directed.

Supply and fix vitreous china urinals half stall urinal (back or corner wall type) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing complete incl making good exisiting surface. (make Cera Cat Pt No S4040114)

Supply and fix in repairs vitreous chinaware coloured wash hand basin with pedestal of size 55X40 cm complete including waste coupling ,waste pipe including fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed.

Supply and fix in repair pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, fancy type screwed for iron of 15mm pipe and fixed complete all as specified and directed.

Supply and fix in repair health faucet mild steel chromium plated suitable for 15mm dia pipe with 1 or 1.25mtrmetre long flexible tube and ABS wall hook fixed to wall complete all as specified and directed.

Supply and fix in repair for 75 mm bore out let cast floor trap spun pipe (conforming to IS 3989) incl cockroach trap with gratings including including jointing to waste pipe fixed in cement concrete tpe B-1 (1:2:4) etc complete all as specified and as directed.

Supply and fix for 75 mm bore Cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, laid in trenches or in floors or fixed to wall vertically complete all as specified and as directed.

Supply and fix factory made Steel ventilator with top hung shutter including hinges, steel peg stay, complete Note: Glass and mesh shall be measured and paid seperately.

Supply and fix steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed .Note: Glass and mesh shall be measured and paid seperately.

Supply and fix for mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding, FE-290 grade E-165 complete all as specfied and directed.

Supply and fix stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fix in repair grating of stainless steel of size 100mm/125mm in circular shape with or with out hole for floor traps fixed with white cement or matching to floor complete all as specified and directed.

Hacking out old broken galss (any thickness, size quality or desription) from wooden frame or sotne, concrete or brick surrounds, glazed with putyy or bised with beads complete all as specified and directed.

Material and labour for providing mirror polishing on existing terrazzo/ kota / udaipur green/ marble stone flooring/skirting by cutting/ grinding and polishing complete all as directed.

Supply and fix sheet glass ordinary quality 4mm thick and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc. 0.5 sqm each pane all corner of glass to be fixed with silicon complete all as specified and directed.

Supply and fix 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sq. m in each pane complete all as specified and directed.

Suppy and fixing MS joist channel (Fe 410-W Gde E-250 Quality A), angle or Tee section,MS tubes, flats square bars etc fixed indepently or framed or without connecting plates ,trusses etc any type framing including purlins and rafters etc confirming to Grade Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr-in-Charge

Material and labour for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed

Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel 0.50 mm thick for ridge cover of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

Material and labour 595 mm X 595mm false ceiling system , using hot dipped galvanised steel section exposed surface with precoated capping, GI powerd coated tee and cross tee of size 24x32mm & 24x27mm having 0.27mm gauge at every 600mm c/c interval and wall angle of size 19x19mm having 0.35mm gauge fixed to the wall. The above grid is tobe suspended at every 1200mm c/c in both direction using 2mm thick pre-straightened GI wire laying designer tile ivory painted (high pressure steam cured) of 4 mm thickness (as per IS 14862) of size 595x595 mm and ant ine of the design (cascadev or electra) , back of the tile duly sanded and finished with a coat of protective paint over the formed grid incl board etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for complete removal of existing treatment from wall upto plaster surface by washing, rubbing down and stopping of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces finally rubbed and smooth with sand paper priming plastered and other surfaces with alkaliresistant priming paint complete all as directed by Engr-in-charge.

Material and labour for preparation of old plastered surface of wall and applying one coat of oil bound distemper complete all as specified and directed.

Material and labour washing, rubbing down and stopping of distempered and painted surfaces of wall and applying two coat of OBD over one coat of primer complete all as specified and directed

Material and labour for preparation of old wall surface and applying one coat of white wash complete all as specified and directed.

Material and labour for preparation of old ceiling surface and applying one coat of white wash complete all as specified and directed.

Material and labour for preparation of old wall surface and applying one coat of distempering with dry distemper white or tinted complete all as specified and directed.

Material and labour for preparation of old wooden surface and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of old steel surface of any description and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for french polishing on surfaces of any description width or girth including cleaning and preparing the surface including a coat of wood filler on old works and one or more coats of polishing complete all as specified and directed.

Material and labour for writing letter or figures (Block, Roman, Italic or Indian) n.exc 30cm complete all as specified and directed.

Material and labour for writing stop commas, short lines, dashes, hyphens, brackets etc complete all as specif eid and directed.

Material and labour for removing old painted by paint removers or burning off by blow lamps and cleaning with scrapers any numbers of coats any width or girth from wooden surface and applying french polishing on surfaces of any description width or girth including cleaning and preparing the surface including a coat of wood filler on old works and two or more coats complete all as specified and directed.

Material and labour for applying external water proof wall putty of 1 to 1.5 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

Material and labour for applying two coats of acrylic distemper over a coat of primer, white or tinted over 1 to 1.5 mm thick wall care putty in two coat on any type of surface complete all as specified & directed.

Material & Labour for preparation of new surface applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm. Complete all as specified and directed.

Material & Labour for preparation of old surface applying one coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on old surface. Complete all as specified and directed.

Material and labour three coats of white wash on ceiling on new/old plastered surfaces including preparation of surfaces complete all as specified and as directed.

Material and labour for providing pre cast RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab and man hole covers etc complete all as specified and directed by Engineer-In- Charge.

Material and labour PCC 1:3:6 type C0 ( using 12.5 mm thick graded stone aggragate) as in surface channel drain. Complete all as specified and directed.

Supply and fix precast cement concrete louvres and jallies, in cement concrete 1:3:6 type C0 ( using 12.5 mm thick graded stone aggragate) 25mm thick fixed in CM 1:4 (mea sured solid), including all mould- ings but excluding frame complete all as specified and directed

Supply and fix push button taps of cast copper alloy, screwed for iron pipe and fixed to 15mm pipe complete all as specified and directed.

Supply and fix urinal spreader of PTMT/ABS body of any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed.

Supply and fix 75mm dia bore PVC (SWR) pipe single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Supply and fix 110mm dia bore PVC (SWR) pipe single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Supply and fix 75mm dia bore PVC (SWR) pipe single socketed, in any length with rubber ring joints fixed incl clamps for fixing to wall complete all as specified and directed.

Supply and fix 110mm dia bore PVC (SWR) pipe single socketed, in any length with rubber ring joints fixed to wall complete incl clamps for fixing to wall complete all as specified and directed.

Supply and fix 75mm bore PVC (SWR) bend of any radius fixed complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) bend of any radius fixed complete all as specified and directed.

Supply and fix PVC (SWR) P trap of 125mm bore complete all as specified and directed.

Supply and fix 75mm bore PVC (SWR) couplers for PVC pipe to join two pipe in series complete all as specified and directed

Supply and fix 110mm bore PVC (SWR) couplers for PVC pipe to join two pipe in series complete all as specified and directed

Cleaning of septic tank of any size capacity by removing sludge in semi solid state or liquid state by manually or by pressure pump including removal of sludge to a distance exc 1.5 Km but n.exc 5 Km out of MOD land complete all as specified & directed by Engineer –in Charge. (Note:- Measurements will be taken only after dewatering of the septic tank).

Cleaning and removing all scale and dirt etc. from tank and from mouth of circulating pipes etc. of tank exc 250 ltr and n. exc 500 ltr capacity, complete all as specified and directed.

Material and labour for stone agg (natural river stone) size exc 5 mm and n.exc 20mm for laying on path/pavement in thickness not less than 50mm incl dismantiling/demolition of existing tiles/PCC of any description incl fixing of brick edging jointed with cement at side of path and revoving debries complete all as specified and directed.

Material and labour minimum 20mm thick and size 150mm x 2700mm WPC lining fluted panels (fixed to wall ceiling) inclusive of solvent and ceiling system with metal grid complete as per manufacturer's instruction. The above grid is to be suspended at every 1200 mm c/c in both direction by suitable supporting system complete all as specified and directed by Engineer-in-Charge

Taking down carefully copper /aluminium point wiring (light, fan , socket or power) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls/floors and reuse the serviceable fittings under respective items complete all as directed. Note :- (i) The contractor/Supervisor collect the complaints from the JE/MCM through JOB Card and rectify the complaints. (ii) The contractor/Supervisor should submit the Job Card duly signed by the user. (iii) RAR/Final bill will be paid only after verifying of workdone by the Engr-in-Charge

Material and labour for point wiring with 3 runs of 1.5 Sqmm (colour code as per IE Rules) FRLS, PVC insulated, unsheathed, single core, 1100 Volts grade, multistranded copper conductor cable/Wire in and including concealed rigid PVC conduit medium grade and green wire connected to common earth dolly, and including 1.6mm thick cadmium plated sunk MS pressed steel terminal boxes with 3.0 mm thick hylum sheet cover fixed with brass screw complete with all accessories for one light point/Fan point controlled by one ,one way switch complete all as specified and directed.

All as per Item No 147 here-in- before but one 3 pin 5 Amps socket out let on the same board with other switches complete all as specified and directed.

All as per Item No 147 here-in- before but one 3 pin 5 Amps switch socket out let on the independent board with other switches complete all as specified and directed.

All as per Item No 147 here-in- before but One bell/buzzer point controlled by bell push complete all as specified .

All as per Item No 147 here-in- before but One light point controlled with switch 2 way complete all as specified.

All as per Item No 147 here-in- before but one three pin 15 Amps switch socket out let on the independent board with 4 sq mm PVC insulated FRLS copper conductor complete all as specified and directed.

All as per Item No 147 here-in- before but point wiring drawn through Surface PVC conduit complete all as specified and directed.

All as per Item No 153 here-in- before but one three pin 5 Amps socket out let on the same board with other switches complete all as specified and directed.

All as per Item No 153 here-in- before but one three pin 5 Amps switch socket out let on the independent board with other switches complete all as specified and directed.

All as per Item No 153 here-in- before but One bell/buzzer point controlled by bell push complete all as specified .

All as per Item No 153 here-in- before but One light point controlled with switch 2 way complete all as specified.

All as per Item No 153 here-in- before but one three pin 15 Amps switch socket out let on the independent board with 4 sq mm PVC insulated FRLS copper conductor complete all as specified and directed.

All as per Item No 147 here-in- before but point wiring drawn through exisitng conduit complete all as specified and directed.

All as per Item No 159 here-in- before but one three pin 5 Amps socket out let on the same board with other switches complete all as specified and directed.

All as per Item No 159 here-in- before but one three pin 5 Amps switch socket out let on the independent board with other switches complete all as specified and directed.

All as per Item No 159 here-in- before but One bell/buzzer point controlled by bell push complete all as specified .

All as per Item No 159 here-in- before but one two way point controlled with switch 2 way complete all as specified.

All as per Item No 159 here-in- before but one three pin 15 Amps switch socket out let on the independent board with 4 sq mm PVC insulate FRLS copper conductor complete all as specified and directed.

All as per Item No 147 here-in- before but wiring drawn through Case & Caping complete all as specified and directed.

All as per Item No 165 here-in- before but one three pin 5 Amps socket out let on the same board with other switches complete all as specified and directed.

All as per Item No 165 mentioned here-in- before but one three pin 5 Amps switch socket out let on the independent board with other switches complete all as specified and directed.

All as per Item No 165 mentioned here-in- before but One bell/buzzer point controlled by bell push complete all as specified .

All as per Item No 165 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 4 sq mm PVC insulated FRLS copper conductor complete all as specified and directed.

Supply and fix in repair Switch piano flush type single pole one way 230 Volts 6 Amp complete all as directed.

Supply and fix in repair Switch piano flush type single pole two way 230 Volts 6 Amp complete all as directed.

Supply and fix in repair Socket outlet 3 pin , 230 Volts 5/6 Amps multipurpose 5 pin complete all as specified and directed.

Supply and fix in repair bell push flush type 5 Amps 230 Volts single pole complete all as specified and directed.

Supply and fix in repair Socket outlet multipurpose having provision for 3 pin, 230 Volts 15/16 Amp and 3 pin, 5/6 Amp, piano flush type complete all as specified.

Supply and fix in repair switch piano flush type, single pole, one way, 230 Volts 15/16 Amps complete all as specified

Supply and fix in repair anglurar Lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fix in repair stepped type regulator socket type double module 5 step for ceiling fan 1200/1400 mm size 230 volts, 6 Amps 120 watts complete all as specified and directed.

Supply and fix in repair ceiling rose, three terminal ISI marked surface bakelite suitable for batten fitting complete all as specified and directed.

Supply and fix in repair calling bell type AC 230 Volt single pole complete all as specified and directed..

Supply and fix Modular white cover plate with frame and metal flush box 2 module complete all as specified and as directed.

All as per item No 180 here in before but 3 module complete all as specified and directed.

All as per item No 180 here in before but 4 module complete all as specified and directed.

All as per item No 180 here in before but 6 module complete all as specified and directed.

All as per item No 180 here in before but 8 module complete all as specified and directed.

All as per item No 180 here in before but 12 module complete all as specified and directed.

Supply and fix in repair Modular switch 1 way 06 amp single pole complete all as specified and directed.

Supply and fix Modular switch 2 way 06 amp single pole complete all as specified and directed..

Supply and fix in repair Modular switch 1 way 16 amp single pole complete all as specified and directed..

Supply and fix in repair modular socket outlet 6/16A- 5 pin combined of 02 module complete all as specified and directed.

Supply and fix in repair modular socket outlet 6A-5 pin combined of 02 module complete all as specified and directed.

Supply and fix in repair moduar bell push 6 Amp 1 module complete all as specified and directed.

Supply and fix in repair modular fan step regulator 120 W-2 module complete all as specified and directed.

Supply and fix in repair LED tube light fitting batten type all in one single phase 18/20 W with lamp 6500/4000 K complete pre-wired all accessories complete all as specified and directed.

Supply and fix in repair mirror light decorative compact luminaries with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix in repair decorative wall mounting light fitting made out of polycarbonated suitable for and incl retrofit 9 watts LED bulb complete all as specified and directed.

Supply and fix in repair LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with IP 65/66 protection complete including bracket made out of 32 mm bore medium grade GI pipe made to shape with bolts, buts & washers of min 1.2 Mtr incl grouting of nuts or fasteners clamps and conductor to fitting with 3 core 1.5 sqmm PVC insulated cable complete all as specified incl taking out old u/s fitting complete. Note: The unit rate include for painting to bracket with one coat of red oxide paint and two coat of alluminium paint before fixing.

Material and labour in replacement for submain wiring with 3 runs(N+P+E) of 1.5 Sqmm single core,PVC insulated, unsheathed, multistranded copper conductor FRLS cable 1100 volts grade drawn through and including concealed/surface PVC conduit pipe of medium duty not less than 15 mm dia including necessary PVC conduit specials and connecting with suitable size thimble complete all as specified and directed. Note:-3 runs of 1.5 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

All as per item No 197 here-in-before but with 3 runs(N+P+E) of 2.5 Sqmm single core copper FRLS conductor . Note:-3 runs of 2.5 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length complete all as specified and directed.

All as per item No 197 here-in-before but with 3 runs(N+P+E) of 4 Sqmm single core copper FRLS conductor .Note:-3 runs of 4 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length complete all as specified and directed.

All as per item No 197 here-in-before but with 6 runs(3 runs P+N+ 2 run Earth) of 6 Sqmm single core copper FRLS conductor and PVC conduit not less than 24 mm dia. Note:-6 runs of 6 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length complete all as specified and directed.

Material and labour for replacement of old rusted sunken box with new 1.6mm thick cadmium plated sunk MS pressed steel terminal boxes with 3.0 mm thick hylum sheet cover fixed with brass screw complete with all accessories and making the good disturbed surface with plastering and white washing etc incl taking downcomplete all as specified and directed .

Material and labour for replacement of old u/s hylum sheet cover fixed with brass screw complete with all accessories and making the good disturbed surface with plastering and white washing etc incl taking down complete all as specified and as directed by Engr-in-Charge.

Supply and fix in repair Distribution board VTPN 4 Way double door, suitable for MCCB 63/100 Amps MCCB as incoming and MCBs for outgoing factory made, IS: 13032 marked with valid CM/L No fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral and earthing link and bus bar. DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and baked at high temperature, painted in seven tank process. The DBs shall be of IP 43 protection incl taking out old u/s complete. Note:- DB and MCCB/MCB shall be of same make

Supply and fix in repair MCCB 415 Volts, 63 Amps, rating 4 Pole , all as specified and directed

Supply and fix in repair MCCB 415 Volts, 100 Amps, rating 4 Poleall as specified and directed

Supply and fix in repair Distribution board SPN 8/12 Way double door, for mounting MCBs isolator, IP 43 protection complete all as specified and directed. Note:- DB and MCCB/MCB shall be of same make

Supply and fix in replacement MCB combo box with steel enclosure with one single pole MCB 20 Amp 10 KA C series suitable for AC/geyser etc complete all as specrified & directed.

Supply and fix in repair 415V 10KA 'C' curve MCB of TPN 40 to 100 Amps complete all as specified and directed.

Supply and fix in repair SP 6 to 32 Amps rating 240V, 10KA 'C' curve MCB complete all as specified and directed.

Supply and fix in repair SPN 25 to 63 Amps rating 240V, 10KA 'C' curve MCB complete all as specified and directed.

Material and labour for earthing complete with galvanized steel plate electrodes of size 600mm x 600mm x 6mm thick buried directly in ground with earth pit not less than 2.25m deep below normal ground level with top edge of plate not less than 1.5 m below normal ground level connected to galvanized wire 4 mm earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanized iron pipe 15 mm bore (light grade) including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm dia MS bar funnel wire mesh 20 mm bore galvanized iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soil complete all as shown in electrical plate No 5 of SSR part 1 including testing on completion all as specified and directed. incl demolition to existing one complete. Note: (i) Earthing has to done by spl persons and if the desired earth resistance is not found within permissible limit shall be redone by contractor at no extra cost. (ii) Cost of GI wire 4 sqmm and 15 mm dia pipe medium grade upto 7.5 mtr is included in the rate quoted for this item

Supply and fix in repair round shaped LED downlights of capacity 12 Watt suitable for fixing in false ceiling with all accessories and including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix in repair round shaped LED downlights are made with injection moulded polycarbonate housing with snap fit/screw fit arrangement of polycarbonate/aluminium spun ring for surface mounting of capacity 12 Watt with all accessories and including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix in repair LED luminaire 600 mm x 600 mm, 35/36 watt, (Whit/warm white as per user equirement )220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

PRAGATI ENTERPRISES