Construction of new Mill Wright Office, Mill Wright Shed and New machine room near new IOH shed Kota.

A-CPWD DSR 2023 Items

Item Breakup - A-CPWD DSR 2023 Items

slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 11.37S CERAMIC GLAZED TILES 11.37 Providing and laying Ceramic glazed floor tiles Sqm 20 1096.55 21931 of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red 42 Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 12.0 ROOFING 12.1S SHEET ROOFING 12.11 Extra for providing and fixing wind ties of 40x Metre 70 195.6 13692 43 6 mm flat iron section. 12.37S RAIN WATER SPOUT AND PIPE Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring 12.41 conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 44 12.41.2 110 mm diameter Metre 30 377.4 11322 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes 12.42 conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 12.42.1 Coupler 45 12.42.1.2 110 mm Each 8 136.15 1089.2 12.42.5 Bend 87.5 degree 46 12.42.5.2 110 mm bend Each 10 150.35 1503.5 Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 12.47 2400 TEX panel rovings incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 12.47.1 2 mm thick corrugated (2.5" or 4.2" or 6") or Sqm 35 1401.35 49047.25 47 step-down (2" or 3" or 6" ) as specified KOTA DIVISION-ENGG/WEST CENTRAL RLY 12.50 Providing and fixing precoated galvanised iron Sqm 700 738.65 517055 profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet 48 should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 12.51 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 49 12.51.1 Ridges plain (500 - 600mm) Metre 55 532.35 29279.25 13.0 FINISHING 13.1S CEMENT PLASTER (IN FINE SAND) 13.1 12 mm cement plaster of mix : 50 13.1.2 1:6 (1 cement: 6 fine sand) Sqm 1500 333.35 500025 13.44S EXTERIOR FINISHING Finishing walls with Acrylic Smooth exterior 13.46 paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 Sqm 1500 160.6 240900 51 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) Painting with synthetic enamel paint of 13.61 approved brand and manufacture to give an even shade : 52 13.61.1 Two or more coats on new work Sqm 1200 155.9 187080 17.0 SANITARY INSTALLATIONS 17.1S General Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, 17.1 with manually controlled device (handle lever) conforming to IS : 7231,with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.1.1 White Vitreous china Orissa pattern W.C. pan Each 1 6767.4 6767.4 53 of size 580x440 mm with integral type foot rests KOTA DIVISION-ENGG/WEST CENTRAL RLY Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush 17.2 pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1 W.C. pan with ISI marked white solid plastic Each 1 6515.55 6515.55 54 seat and lid Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing 17.4 cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.4.1 One urinal basin with 5 litre white P.V.C. Each 2 6258.75 12517.5 55 automatic flushing cistern 17.7B Providing and fixing wash basin with C.I. Each 3 1550.6 4651.8 brackets, 15 mm PTMT pillar cock, 32 mm PTMT waste coupling of standard pattern, including painting of fittings and brackets, 56 cutting and making good the walls wherever required. White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm PTMT pillar cock. 17.8 Providing and fixing white vitreous china Each 3 1683.35 5050.05 pedestal for wash basin completely recessed 57 at the back for the reception of pipes and fittings. Providing and fixing P.V.C. waste pipe for sink 17.28 or wash basin including P.V.C. waste fittings complete. 17.28.1 Semi rigid pipe 58 17.28.1.1 32 mm dia Each 3 103.9 311.7 18.0 WATER SUPPLY 18.7S C.P.V.C. PIPES Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one 18.8 step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 59 18.8.2 20 mm nominal dia Pipes Metre 50 537.6 26880 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and 18.10 making good the walls etc. ( Internal work - Exposed on wall ) 60 18.10.1 15 mm dia nominal bore Metre 30 366.4 10992 61 18.10.3 25 mm dia nominal bore Metre 30 551.7 16551 Providing and fixing G.I. pipes complete with 18.12 G.I. fittings including trenching and refilling etc. External work 62 18.12.3 25 mm dia nominal bore Metre 70 467.75 32742.5 63 18.12.6 50 mm dia nominal bore Metre 40 762.15 30486 18.15S BRASS FITTINGS KOTA DIVISION-ENGG/WEST CENTRAL RLY Providing and fixing gun metal non- return 18.19 valve of approved quality (screwed end) : 18.19.1 25 mm nominal bore 64 18.19.1.1 Horizontal Each 2 591.4 1182.8 65 18.19.1.2 Vertical Each 2 624.1 1248.2 Providing and fixing uplasticised PVC 18.21 connection pipe with brass unions : 18.21.1 30 cm length 66 18.21.1.1 15 mm nominal bore Each 2 85 170 C.I. SLUICE VALVES/ FIRE HYDRANTS & 18.31S FIXTURES Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and 18.46 making long screws etc. complete (New work) : 67 18.46.1 15 mm nominal bore Each 6 318.35 1910.1 68 18.46.3 25 mm nominal bore Each 6 439.25 2635.5 69 18.46.6 50 mm nominal bore Each 4 823.8 3295.2 18.48 Providing and placing on terrace (at all floor Per 1000 11 11000 levels) polyethylene water storage tank, IS : Litre 12701 marked, with cover and suitable 70 locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 18.54S PTMT FITTINGS Providing and fixing PTMT bib cock of 18.54 approved quality and colour. 18.54.1 15 mm nominal bore, 86 mm long, weighing Each 2 125.6 251.2 71 not less than 88 gms Providing and fixing PTMT grating of approved 18.58 quality and colour. 18.58.1 Circular type 72 18.58.1.1 100 mm nominal dia Each 5 37.6 188 18.59S AIR VALVE & WATER METER (BULK TYPE) Providing and fixing PTMT Ball cock of approved quality, colour and make complete 18.62 with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 18.62.1 15 mm nominal bore, 105 mm long, weighing Each 3 182.1 546.3 73 not less than 138 gms 18.63 Providing and fixing PTMT angle stop cock 15 Each 3 156.9 470.7 74 mm nominal bore, weighing not less than 85 gms Providing and fixing PTMT extension nipple for 18.75 water tank pipe, fittings of approved quality and colour. 18.75.1 15 mm nominal bore, weighing not less than Each 2 53.6 107.2 75 32 gms 21.0 ALUMINIUM WORK 21.1S General KOTA DIVISION-ENGG/WEST CENTRAL RLY Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket 21.1 etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : 21.1.1 For fixed portion 21.1.1.1 Anodised aluminium (anodised transparent or Kg 300 495.05 148515 76 dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings 21.1.2 wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 21.1.2.1 Anodised aluminium (anodised transparent or Kg 250 598.6 149650 77 dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene 21.3 gasket etc. complete as per the architectural drawings and the directions of engineer-in- charge . (Cost of aluminium snap beading shall be paid in basic item): 21.3.1 With float glass panes of 4.0 mm thickness Sqm 33 1176.8 38834.4 78 (weight not less than 10kg/sqm) Total 19565131.30

Item Breakup - B-NS Items