Furnishing of New KGS (Sales Outlet) at Koothattukulam in Ernakulam District

Amount

APPENDIX-A

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes ( D S R 10.16.1 )

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling , partition etc. complete (frame work to be paid seperatately). 8 MM thick Cement fiber board as per IS: 14862 ( D S R 12.26.1 )

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: Gypusm Plaster Board of size 1200 x 2400 x 12.5 mm, with all 4 side tapered ( D S R 2016 12.45.1. )

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: ( D S R 25.7. )

Providing and applying Plaster of paris Putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. ( D S R 13.26 )

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer ( D S R 13.43.1 )

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work ( D S R 2018 , 13.52.1 )

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work. ( D S R 13.60.1. )

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work. ( D S R 13.61.1 . )

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : One or more coats on old work ( 2018 D S R 13.98.1 )

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work. ( 2018 D S R, 13.99.1 )

Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (Two or more coats applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface ( 2018 D S R 13.111.1 )

Floor painting with floor enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work ( D S R 2018 13.66.1 )

Providing and fixing Aluminium work for Doors, Windows, Ventilators and Partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion - Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) ( D S R 21.1.1.3 )

For Shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) ( D S R 21.1.2.3 )

Providing and fixing 12 mm thick Prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides ( D S R 21.2.2. )

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness ( D S R 21.3.2. )

Providing and fixing PVC, pipes fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 6 Kgf/cm2 - internal work- Exposed on wall ( Observed Data Buildings 50.18.7.4.2. )

Providing and fixing Name Board in Existing ACP Surface Using Acrylic LED 3 D Letters using 3 mm Thick exterior grade and heat resistant acrylic sheets ( ISO CERTIFIED ), with 1.5w HI BRIGHT, SAMSUNG , ADS, BNEZ Water proof L.E.D ( RoHS ), and S M P S 400W power supplies with 30% extra backup, Branded, weatherproof , with approved brand full copper wiring , including all cost of labor and Scaffolding charges as directed by the engineer in charge.( od42043/2023_2024 )

ENGAGING LABOUR FOR MAINTENANCE WORK, CLEANING WORK - BELDAR od51563/2023_2024

ENGAGING LABOUR FOR MAINTENANCE WORK REPAIR WORKS FITTER GRADE 2 od51564/2023_2024

ENGAGING LABOUR FOR MAINTENANCE WORK REPAIR WORKS CARPENTER GRADE 1

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : Decorative veneer facings of approved manufacture ( D S R 8.28.1 )

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, For all leads including all lifts involved. ( D S R 2018 , 15.60 )

Providing and Fixing plywood Back ground panel made out of FRAME work using 16 mm BWR QUALITY ( IS 303 grade ) plywood at suitable spacing both horizontally and vertically, including making hole in the concrete/ masonry wall, with necessary SS hold fasts or SS screws of necessary size. Then Commercial plywood 12 mm thick B W R grade ( IS 303 Grade ) of approved make is fixed to the Exposed side of the frame work with screws of necessary size , all the exposed surface covered by 1.00 mm thickness Decorative Laminated Sheets with suitable adhesive ( Heatex or Equivalent ) including sealing all the joints and holes all as per the approved drawings and Direction of the Engineer in Charge .

Providing and fixing WOODEN Display shelf for Ornamental Items ( RACK BEHIND CASH COUNTER ) with frame work using 16 MM BWR ( IS 303 GRADE ) PLY WOOD , providing 12 mm thick ( IS 303 GRADE ) BWR ply wood on rear side, covering the frame work with 16 mm ( IS 303 GRADE ) BWR ply wood, covering the exposed surface with 1.00 mm thickness Decorative laminated sheets with addhessive of approved brand ( Heatex or Equivalent ) , providing 12 mm thick edge mechine polished glass for racks with necessary supports in the upper portion, providing 16 mm thick BWR ( IS 303 GRADE ) PLY WOOD SHUTTERS INCLUDING NECESSARY HINGES , HANDLES ETC for racks in the lower area, applying 1 coat of wood primer , putty finishing , synthetic enamel 2 coat all as per the drawing and Direction of the Engineer in Charge .

Providing and fixing Wooden Display shelf with frame work using 16 mm thick IS 303 GRADE BWR Plywood , covering the frame work with 16 mm thick IS 303 Grade BWR Quality ply wood, covering all the exposed surface with 1.00 MM thickness decorative laminated sheet with Texture Finish using good quality addhessive ( Heatex or Equivalent ) providing 12 mm thick edge mechine polished glass for racks with necessary supports, all as per the drawing and Direction of the Engineer .

Providing Name Board by Vinyle Sticker Work on Existing ACP PANNEL WORK as per approved Design

Providing and fixing DISPLAY SHELF , Horizontal Spacing 90 cm and vertical Spacing 45 cm with 40 MM AND 25 MM M S Hollow tubes, channels, plates etc., and 8 mm Glass , including welding, grinding, providing 2 coats of primer and 2 coat of Epoxy Paint ( SPRAY fiNISH ) etc complete, including fixing the Shelf to the Wall / Columns with necessary accessories & stainless steel dash fasteners , Providing 8 mm Glass of of required size, including polishing the exposed edges , all as per the Drawing and approval of the Engineer-in-charge,

Provision for Providing Glass Of Different Sizes LS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. GROUP B ( D S R ELECTRICAL 1.10.2 )

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required. 3 X 1.5 sq.mm ( D S R ELECTRICAL 1.17.3 )

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required. 3 x 2.5 sq. mm ( D S R ELECTRICAL 1.17.12 )

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required. 3 x 4 sq. mm ( D S R ELECTRICAL 1.17.21 )

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 20 MM ( D S R ELECTRICAL 1.21.1 )

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 25 MM ( D S R ELECTRICAL 1.21.2 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch ( D S R ELECTRICAL 1.24.1 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch ( D S R ELECTRICAL 1.24.3 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet ( D S R ELECTRICAL 1.24.4 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet ( D S R ELECTRICAL 1.24.5 )

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. ( D S R ELECTRICAL 1.26 )

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm) ( D S R ELECTRICAL 1.27.1 )

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 3 Module (100mmX75mm) ( D S R ELECTRICAL 1.27.2 )

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 6 Module ( D S R ELECTRICAL 1.27.4 )

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.12 Module (200mmX150mm) ( D S R ELECTRICAL 1.27.6 )

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). ( D S R ELECTRICAL 1.31 )

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator2+12 way, Double door ) ( DSR ELECTRICAL 2.3.8. )

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single Pole ( D S R ELECTRICAL 2.10.1 )

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required ( D S R ELECTRICAL 2.11 )

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. ( 40 Amps ) ( D S R 2.12. 1 )

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. ( 63 Amps ) ( D S R 2.12. 2 )

Supplying and fixing following rating, Double pole, ( Single phase and neutral), 240 volts, Residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amps ( D S R ELECTRICAL 2.14.3. )

Supply, Conveyance , Installation, testing and commissioning of Wall mounting fan of 400 mm Sweep with Oscillation System and Pull Cord, Fixing to wall with wall mounting brackets supplied along with the fan and Giving Connections with Existing wire etc. complete. od28805/2023_2024

Supply Conveyance, installation, testing and commissioning of sleek compact recess mounting LED Slim Panel Light Fitting 18 W, Square or Round, Cool or Warm,size 205 mm or nearest available , with light weight body, energy efficient drive , complete with all accessories , fixing directly on ceiling including giving connections with required length of 3 core round copper conductor flexible wire confirming to the relevant ISS or extending the original wire etc. as required od28806/2023_2024

Supply Installation , testing , Commissioning of Sleek Compact Recess Mounting, LED Slim Panel Light Fitting Square or Round, Cool or Warm, 12 w of size 155 mm or Nearest available size, with Light Weight Body, Energy efficient Drive, with all accessories, fixing directly on ceiling including giving connections with required length of 3 core round copper conductor flexible wire confirming to relevant ISS or extending the original wire etc. as required od28807/2023_2024

Supply Conveyance, Installation, Testing and Commissioning of Sleek Compact Recess Mounting LED Slim Panel Light Fitting 6 w , Square or Round , Cool or Warm, Size 105 mm or nearest available size, with Light weight Body , Energy Efficient Drive,complete with all accessories, fixing directly to the Ceiling including giving connection with required length of 3 core round copper conductor flexible wire confirming to relevant ISS or extending the original wire etc. as required od28808/2023_2024

Supply, Conveyance, Installation, Testing and Commissioning of Sleek , Compact Recess Mounting LED Slim Panel Light Fitting 3W or 4W, Round or Square, Cool or Warm, Size 75 mm or nearest available , with Light weight Body, Energy efficient Drive,complete with all accessories ,fixing directly on ceiling, Giving connections with required length of 3 core copper conductor flexible wire confirming to relevant ISS or extending the original wire etc. as required od28809/2023_2024

Supplying installation testing and commissioning of 2 Ton Split Air conditioner ( INVERTOR AC ,FULL COPPER ) with remote control of make Voltas / Blue Star / L.G /.Carrier or equivalent make with 1 unit of Voltage stabilizer ( V Guard VG 500 Stabiliser or Equivalent approved make suitable for 2 Ton invertor AC ) , providing angle iron / Wall Munting Bracket support to the out door and indoor unit , copper tube, cable etc complete. including cutting and making good of the masonry wall / concrete as directed by the Engineer in Charge .

Supplying , installing , testing and commisioning CC TV System with CP Plus –2.40 MP AHD IR D/N Dome Camera with 3.6 mm Lens, IR Distance 20 meter. 6 Nos , CP Plus 8 channel . Standalone DVR with TCP / IP / LAN / Eithernet, remote, channeling, playback, motion, mobile imaging, with out HDD. 1 unit, A/C D/C Power supply 5 Amps SMPS -1 , RCA/BNC Cable Connecters - 12 nos, 2 TB HDD -1 , 1 18.5” Monitor , with Cabling with 3+1 control cable and accessories as required

PROVISION FOR LOADING , CONVEYANCE, UNLOADING CHARGES OF OLD FURNISHING UNITS FROM KALOOR KGS TO NEW KOOTHATTUKULAM KGS

Providing and fixing DISPLAY COUNTER FOR Village Industries Products ( SIZE 1.60 X 0.90 X 1.20 M ) with stainless steel ( Grade 202 ) Hollow tubes, channels, plates etc., and 12 mm Glass , including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the Shelf in position with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., Providing 12 mm Glass of of required size, including polishing the exposed edges , all as per the Drawing and approval of the Engineer-in-charge,

HARIDAS, G

R. Sajikumar