WS schemes in North Tripura District under UWS/15th FC Fund 2025-26/SH-Replacement and mtc. of electrical accessories, Loweing lifting, Rewinding of pump motor etc. for different DTW, SBDTW of Panisagar Nagar Panchayat of DWS Sub-Division, Panisagar

SBDTW mtc Providing and fitting fixing steel sheet enclosed switch fuse unit (suitable for DIN fuses), triple pole with Neutral Link (TPN), 415/500 Volt, L & T / Havells / BCH make etc. complete as per specification and direction of the Engineer-in-charge i). 32 amps

Repair and maintenance of submessible Motor suitable for submerssible pumpset by complete dismantling in/c providing & fitting fixing of PVC ( IS : 8783-1978 ) insulated electro grade copper ( IS : 613-1984 ) conductor winding in stator & all necessary spare parts and reassembling the same including servicing of rotor & necessary trial run as per specification and direction of the Engineer-in-charge. 2.0 HP Motor suitable for 2000 GPH capacity submerssible pumpset

Providing and fixing of UPVC end cap / well cap suitable for UPVC 'CM' casing or 'CS' casing or 'RS' pipes as per specification and direction of the Engineer - in - charge. i) 150 mm dia

Providing and fitting fixing with PVC insulated single core multistrand Copper cable conforming to IS : 694 for inter connection with all electrical equipments of the pannel board as per specification and direction of the Engineer-in-charge. i) 10 sqmm

Supplying and fitting fixing of M.S.(18 SWG) "KIOSK" ( size width 450mmXlength 1200mmX height 850mm) fitted with 4 nos suportt of 75 mm X 75mm( 6mm thick) M.S. angle for embedding in 1:2:4 cement concrete base ( size 300 mm X 300 mm dia X600 mm) with proper locking arrangement and coated with anti corrosiv paint ( both inside and outside) including necessary provision for fitting fixing of single phase motor starter unit main switch energy meter etc complete in all respect as per direction of the engineer in charge.

Providing and fixing C.I. non-return valve of approved quality as per CPWD specification and direction of the Engineer - in charge. i. 50 mm nominal bore

Providing and fitting fixing G.I. pipe (medium class) conforming to IS : 1239 for OHP of approved quality as per specification and direction of the Engineer-in-charge i. 40 mm dia

Lowering of submerssible pump of 45.0 Mtr. Head with suitable single phase submerssible motor including additional 32.00 Mtr submersible 3 core copper flat cabl e(2.5 mm2 size) complete all respect as per direction of the Engineer-in- Charge. a) for 2000 GPH capacity submersible pump with 3HP submersible motor.

Lifting of submerssible pump of 45.0 Mtr. Head with suitable single phase submerssible motor including additional 32.00 Mtr submersible 3 core copper flat cable(2.5 mm2 size) complete all respect as per direction of the Engineer-in- Charge. a) for 2000 GPH capacity submersible pump with 3HP submersible motor.

Complete repairing of submerssible pump of 45.0 Mtr. Head with suitable single phase submerssible motor as per direction of the Engineer-in- Charge. a) for 2000 GPH capacity submersible pump with 3HP submersible motor.

Rewinding Repair and maintenance of 5 HP / 7.5 HP Motor suitable for 2500 GPH capacity submerssible pumpset by complete dismantling in/c providing & fitting fixing of PVC ( IS : 8783-1978 ) insulated electro grade copper ( IS : 613-1984 ) conductor winding in stator & all necessary spare parts and reassembling the same including servicing of rotor & necessary trial run as per specification and direction of the Engineer-in-charge.

Repair and maintenance of 10 HP / 12.5 HP Motor suitable for 5000 GPH capacity submerssible pumpset by complete dismantling in/c providing & fitting fixing of PVC ( IS : 8783-1978 ) insulated electro grade copper ( IS : 613-1984 ) conductor winding in stator & all necessary spare parts and reassembling the same including servicing of rotor & necessary trial run as per specification and direction of the Engineer-in-charge.

Repair and maintenance of 2500 GPH capacity submerssible pump by complete dismantling including providing and fitting fixing of all necessary spare parts ( conforming to IS : 8034 ) and reassembling the same including machining, servicing & necessary trial run as per specification and direction of the Engineer-in-charge.

i) Bronze/SS Impeller

ii) Bronze grade LTB 2 / Cutless rubber bush

iii) Bronze grade LTB 2/12% chromium steel grade shaft sleeve

iv) Stainless steel pump shaft

VIII) SS impeller lock

iX) SS half coupling

X)Stud bolt & nut

xi) Dismantling, repairing, reassembling, servicing

Repair and maintenance of 5000 GPH capacity ubmerssible pump by complete dismantling including providing and fitting fixing of all necessary spare parts ( conforming to IS : 8034 ) and reassembling the same including machining, servicing & necessary trial run as per specification and direction of the Engineer-in-charge.

i) Bronze/SS Impeller

ii) Bronze grade LTB 2 / Cutless rubber bush

iii) Bronze grade LTB 2/12% chromium steel grade shaft sleeve

iv) Stainless steel pump shaft

V) Cast iron grade(FG200)discharge casing

VI) Cast iron grade(FG200) suction casing

VII Cast IronGrade(FG200)pumpbowel/diffuser

VIII ) SS impeler lock

ix ) SS half coupling

X) Stud Bolt and Nut

xi) Dismantling, repairing, reassembling, servicing

Lowering Lifting Labour charge for lifting of 20000/100000/5000 GPH capacity water lubricanted vertuicla submerssible pump with motor in/c 80ft column pipe assembly by heavy duty chain pully block as per direction of the Engineer-in-charge.

Labour charge for fiting fixing of 20000/100000/5000 GPH capacity water lubricanted vertuicla submerssible pump with motor in/c 80ft/100 column pipe assembly by heavy duty chain pully block as per direction of the Engineer-in-charge.

Supplying fitting fixing of following spare parts of approved quality suitable for pump motor set etc as per direction of the engineer in charge. B) Full threaded nut bolt of 10mm dia and 50mm long.

Providing & fitting fixing of G.I. flange ( 10 mm wall thickness ) by welding with G.I. / MS pipe and placing position as per specification and the direction of the Engineer in charge.

i) For 50 mm dia

ii) For 65 mm dia

iii) For 80 mm dia

iv) For 100 mm dia

Providing and fixing G.I. Bend /elbow in the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge.

i) 40 mm dia

ii) 50 mm dia

iii) 65 mm dia

iv) 80 mm dia

v) 100 mm dia

Providing and fixing G.I. Reducer with the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge.

i) 50 x 40 mm dia

ii) 65 x 50 mm dia

iii) 80 x65 mm dia

iv) 100 x 80 mm dia

Providing and fixing G.I. socket as per CPWD specification and direction of the Engineer - in - charge

i) 40 mm dia

ii) 50 mm dia

iii) 65 mm dia

iv) 80 mm dia

v) 100 mm dia

Providing and fixing G.I. union as per CPWD specification and direction of the Engineer - in - charge.

i) 40 mm dia

ii) 50 mm dia

iii) 65 mm dia

iv) 80 mm dia

v) 100 mm dia

Pannel board Mtc Providing and fitting fixing of 3ph LED indicator lamp fitted on panel board in 3 different colours of 240 Volts( cat No:HS-03F, L&T make) complete as per direction of the Engineer-in-charge.

Providing and fitting fixing with PVC insulated single core multistrand Copper cable conforming to IS : 694 for inter connection with all electrical equipments of the pannel board as per specification and direction of the Engineer-in-charge. i) 16sqmm

Providing and fitting fixing steel sheet enclosed switch fuse unit (suitable for DIN fuses), triple pole with Neutral Link (TPN), 415/500 Volt, L & T / Havell's/BCH make etc.complete as per specification and direction of the Engineer-incharge

i) 63amps

i)100amps

Repairing of existing L&T make FASD satrter by providing and fitting fixing of necessary spares contact kitb ( in /c spare coil ) , repalcement of demaged connection wire in the staretr , testing and commissioning etc.. Asper specification and direction of the engineer -in -charge.

Providing and fitting fixing of Fully Automatic Star Delta type Motor starter ( 3 ph. 50 Hz, 415V, in Steel Sheet Enclosures with Contractors and Timer etc. complete suitable for submersible Pump L & T, BCH, ABB make as per specification and direction of the Engineer-in-charge.

i)25HP/18.5 KW Relay range within 13-21+10%

i)35HP/25 KW Relay range within 13-21+10%