AUGMENTATION TO AC AND REF SHOP,SHIPWRIGHT SHOP,FOUNDRY, ICE SHOP,ELECTRICAL SHOP,AUX MACHINERY SHOP AND HULL FABRICATION AT NSRY KOCHI

Amount

LIST OF WORKS

Schedule A Part I( to Part XIII)

Total amount of Sch 'A' Part-I (Buildings & Structures)

Total amount of Sch 'A' Part-II ( Excavation, Earth work and Site clearence)

Total amount of Sch 'A' Part-III (Internal Electric Supply)

Total amount of Sch 'A' Part-IV (Internal Water Supply)

Total amount of Sch 'A' Part-V (Road/Path/Culvert/Hardstanding)

Total amount of Sch 'A' part-VI (External Electric Supply)

Total amount of Sch 'A' part-VII(Addn/Altn and Special Repair B/R )

Total amount of Sch 'A' part-VIII(Addn/Altn and Special Repair E/M )

Total amount of Sch 'A' part-IX(Dismantling B/R AND E/M)

Sch 'A' Part- X(MISCELLANEOUS) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Boring for cast-in-situ bored piles of 500mm dia to any depth through any type of soil/strata by DMC method using bentonite slurry including removal of bored materials to place outside MD land all as specified and as directed . Note:-The rate shall include mobilisation,erection,dismantling and demobilisation of equipment for pile boring including all labours and material. Nothing extra shall be payable for mobilisation of equipment seperately.

RCC with ready mix concrete(RMC) M30 grade in cast in situ bored pile with minimum cement content 400kg/cum of any length/any sections complete all as specified and as shown on drg including non destructive integrity test on all pile as per IS 2911 part IV. Note:-(i) Reinforcement will be measured and paid separately under relevant items

RCC with ready mix concrete(RMC) M30 grade in pile cap , grade beam & tie beam complete all as specified and shown on drg. Note:-(i) Reinforcement will be measured and paid separately under relevant items

Providing TMT bars (CRS/HCRM/CRM) in reinforcement 10mm dia and over for bored piles of any length and any dia all as shown on drgs including cut to length, bend to required shape, cranking/hooking ends if necessary and binding with 0.9mm dia MS wire annealed or welding so as to secure the bar firmly in position/required shape complete all as specified and shown on drgs.

Providing TMT bars (CRS/HCRM/CRM) in reinforcement 10mm dia and over for grade beam/tie beams and pile caps of any length and any dia all as shown on drgs including cut to length, bend to required shape, cranking/hooking ends if necessary and binding with 0.9mm dia MS wire annealed or welding so as to secure the bar firmly in position/required shape complete all as specified and shown on drgs.

Providing TMT bars (CRS/HCRM/CRM) in reinforcement 5mm dia and over up to and including 12mm dia as in stirups for pile caps and gared beams including cut to length, bend to required shape, cranking/hooking ends if necessary and binding with 0.9mm dia MS wire annealed or welding so as to secure the bar firmly in position/required shape complete all as specified and shown on drgs.

All as per item No 18 above but 5mm dia and over up to & including 12 mm dia as in helicals of pile reinforcement including rings and necessary tack welding to pile reinforcement at all points of contacts.

PCC (1:4:8) type D2 using 40mm graded stone aggregate for concrete layer below pile caps/grade beams and foundation complete all as specified and shown on drgs.

Providing testing equipment & load and testing of 500mm dia bored pile (Initial Load test) all as per IS including removing the testing equipments from site after testing is completed all as specified and directed.

Providing testing equipment & load and testing of 500mm dia pile (Routine Load test) all as per IS including removing the testing equipments from site after testing is completed all as specified and directed.

Conducting standard penetration test all as per IS-2131 at levels location as directed for 500mm dia cast in situ piles all as specified and as directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep or area not exceeding 10 sqm on plan in soft/loose soil including bailing out/pumping out water on account of spring/rain or any other causes using any method as required and as directed by Engr-in-Charge for pile caps/plinth beams,raft foundation etc all as specified and shown on drawings.

Returning filling in around pile cap, plinth beams, raft foundation etc using excavated soil including spreading levelling and well ramming in layers not exc 25 cm thick all as specified and directed.

Removal of surplus soil to a distance not exceeding 50m deposited whereever dircted at a level not exc 1.5 m above starting point .

Formwork to sides of pile caps , grade beams rough finished surface of concrete flat all as specified .

DISMANTLING/DEMOLITION: Dismantling of existing water proofing treatment consisting of cement mortar, tarfelt and foreign materials etc including cleaning the surface and removal of dismantled materials outside MD land all as specified and as directed by the Engineer-in-Charge.

Taking down old unserviceable rolling shutters including fittings, opening size exceeding 5 Sqm and not exceeding 20 Sqm each complete all as specified and as directed by the Engineer-in-Charge.

Taking down unserviceable light fittings of any type all as specified and as directed by the Engineer-in-Charge.

Taking down unserviceable Main switch, DBs incl MCBs with woooden/GI/MS sheet board etc complete all as specified and as directed by the Engineer-in-Charge.

Taking down carefully copper/Aluminium submain wiring of any size/core/type complete including conduits/casing caping etc, removing the materials/debris and keep in safe custody for credit all as specified and as directed by the Engineer-in-Charge.

Taking down existing cable of any size complete all as specified and as directed by the Engineer-in-Charge.

Taking down existing old panel board of any type and size including demolition of foundation complete all as specified and as directed by the Engineer-in-Charge.

Taking down old unserviceable earthing of any type complete all as specified and as directed by the Engineer-in-Charge.

Taking down existing old industrial sockets of any type complete all as specified and as directed by the Engineer-in-Charge.

ADDN/ALTN AND SPECIAL REPAIR B/R: Supply and fixing pre-painted galvalume roofing system aluminium zinc coating GI based steel sheet 0.50mm BMT and 0.55 TCT made to shape and fixed to RCC slab with SDST screws of 12Gx14TPI-55(L) all as shown as per TD drg No. TD/A/2020/02 sheet No/01/01(the rate inclusive of the rate of SDST screws)complete all as specified and as directed by the Engineer-in-charge.

Supply and fixing Galvanized Z section as in purlins where connected on RCC slab with fastener of 10mm dia and 40mm long(Ref TD/A/2020/02 sheet 01/01)(the rate inclusive of the rate of fastener) complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for removal of oil, dirt, laitance and other containments by manually and surfaces shall be fairly smooth finish. Injection grouting of construction joints and honey combs if any with cementitious pressure grouting with 40psi pump using Cobex 100 or equivalent@225gms mixed to 50kg bag of cement including joints packing using polymer modified mortar. Providing and applying pitch free polyurethane water proof coating using Fosroc Nitoproof 600 or equivalent over dry surface at 1.5m thick in 2 coats with interval period of 6 hours over a substrate at coverage rate of 2kg/sqm using spray/squeegee/roller/brush. Water proofing coating shall have the elongation of 2005(ASTM D412-90, tear resistance of >7N(ASTM D 624-00)and tensile strength of >1.5N/mm2(ASTM D412-90)and it should have a solid content of 80-85%. Sprinkle fine aggregate straight after the application of Nitoproof 600PF to get the mechanical key complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 100 mm thick PQC with minimum flexural strength of 45 Kg/Sqcm using non circular synthetic fibre@ 0.25 % by wt of cement vibrating with pin vibrator/screed vibrator and surface finished even and smooth complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for construction joints of size 4mm x 20mm deep to form panels of size 4mx3m in early stage to avoid shrinkage cracks using groove cutting machine with diamond cutting wheel and filling with bitumen sealant to required depth complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 600x600mmx14 to 16mm thick heavy duty industrial grade tiles of (Johnson Endura /Somany or equivalent), in floors fixed with neat cement slurry on flooring jointing white/ coloured cement to match over complete all as specified and as directed by the Engineer-in-Charge.

All as per Item No 42 here in before but in skirting all as specified and as directed by the Engineer-in-Charge.

Supply and fix Anodised aluminium sliding window frame without sash bar, including all necessary jointing cleats, hold fasts, rubber gasket, anodised snap beading, anodised aluminium fitting such as 'F' channel if required for wire mesh or aluminium grill, aluminium handle, locking arrangement etc based on the following Hindalco catalogue No complete all as specified and as directed by the Engineer-in-Charge. 1. 4095 - 61.98x29.70x1.60mm = 3 Track . 2. 9777 - 39.00x20.00x1.60mm = Shuter Vertical 3. 3994 - 41.00x20.00x1.20 = Shutter Top & Botam. 4. 9778 - 39.00x20.00x1.50mm = Shutter Vertical Inter Lock

Supply and fix Anodised aluminium sliding window and ventilator frame without sash bar, including all necessary jointing cleats, hold fasts, rubber gasket, anodised snap beading, anodised aluminium fitting such as aluminium fitting such as 'F' channel if required for wire mesh or aluminium grill, aluminium handle, locking arrangement etc based on Hindalco catalogue No: 1. 4095 - 61.98x29.70x1.60mm = 2 Track . 2. 9777 - 39.00x20.00x1.60mm = Shuter Vertical 3. 3994 - 41.00x20.00x1.20 = Shutter Top & Botam. 4. 9778 - 39.00x20.00x1.50mm = Shutter Vertical Inter Lock complete all as specified.

Supply and fix Aluminum powder coated deco grill DG 104 75mm aperature, made out of 7.5mm plate and finished grill will have 7.5mm width and 6mm thick with rubber beading & hooks etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Preparing new steel surface and applying two coats of anti corrosive epoxy paint over a coat of appropriate primer complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix Chromium plated health faucet shower with CP flexible pipe of 15mm bore complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Preparation of new external plastered surfaces and applying two coats of weather proof(Antifungal Ultima Protek or other approved make)paint over a coat of suitable primer complete all as specified and as directed by the Engineer-in-Charge. Note:- Application of paint, primer and wall care putty shall be as per Manufacture,s Instructions.

Material and labour for Complete removal of existing treatment including removal of vegetation from external surfaces by using modern tools and techniques like pre watered jet , mechanical grinding etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for one coat of primer on old plastered putty finished external wall surfaces complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Two coats of antifungal paint on external plastered surface. Second coat shall be applied after approval of first coat from Engineer-in Charge .

Material and labour for Complete removal of existing treatment of internal surfaces by using modern tools and techniques like pre watered jet , mechanical grinding etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for one coat of primer on old plastered putty finished internal wall surfaces complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 3mm thick wall care putty on old plastered internal wall surfaces after mechanical grinding complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Two coats of oil bound distemper on internal surfaces. Second coat shall be applied after approval of first coat from Engineer-in-Charge.

Material and labour for preparing old steel surface and applying two coats of anti corrosive epoxy paint over a coat of appropriate primer complete all as specified and as directed by the Engineer-in-Charge. Make: Asian paints or other approved make

Supply and fix 1.25mm thick steel rolling shutters, with or without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated complete, motorised elcetrically operated shutter all as specified and as directed by the Engineer-in-Charge.

Supply and fix Draprery rod 32 mm dia with brass coupling and bracket at both ends powder coated, coloured all as specified and as directed by the Engineer-in-Charge.

Material and labour for 12mm thick Mineral fiber Acoustic board/tiles having humidity resistance of 90% for insulation and acoustic purpose 60x60cm in size laid on Aluminium frame work on snap grid complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix Powder coated Aluminium partition, Section weighing 0.55Kg/M including necessary jointing cleats, Glazing clip, ruber Neoprene packing, snap beading Screws etc including 12mm thick Prelaminated Particle board, Exterior grade Pre-laminated both side with decorative choice laminations fixed with Aluminium Frame work with Sheet glass 4mm thick ordinary quality and fixed with aluminium frame work with glazing clip Ruber Neoprene packing in square exc 0.5Sqm in each pane complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Chip and removing all damaged and de bonded concrete and plaster from the RCC column, beam, flights, landing railing and slabs by manually orechanically so as to expose the corroded reinfoorcement bars including the rent of tools, scaffolding and labour charges for dumping the debris with in a lido of 100 meters as directed by the Engr-in -chagre.

Material and labour for application of nitobond EP (manufactured by M/S FOSROC chemicals india Ltd)over the exposed steel reinforcements after removing the rust scales from the exposed reinforcement rods in one square meter area including the cost of all materials rent tools ,scaffolding, sand cost of painting brush complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Renderoc RG (Manufactured by M/S FOSROC chemicals india LTD) to an average thickness of 70mm for beam and column, fluid micro concrete shall be mixed with 6mm down coarse aggregate and specifed quantity of water and mixed using a power operated slow speed stirrer and pouring inside the form work including the cost of all materials rent of tools scaffolding , and drills and all labour charges etc complete all as specified and as directed by the Engineer-in-Charge.

Design , Supply , installation,testing and commissioning of Electrically overhead travelling(EOT)cranes confirming to IS 807, IS 4137 and IS:3177 suitable for operation on 415volts 3 phase 4 wire 50Hz supply double grider box type with necessary steel supporting structure with hoisting cross travel(CT) and long travel(LT)with variable voltage veriable frequency (VVVF)drives of suitable capacities in flame proof enclosure with control pannel power and controlling cables confirming to relevant IS controlled by pendant control with creep speed@10%(ten percent of main hoisting speed)in hoisting only no auxillary hoist and facility for mechanical lowering only at very slow speed in case of power failure and motor failure when a container is hanging on hook, provn of of cover lock with crane hook on power failure the crane should lock on its current position and crane should be provided with one No platform spanwise of width 750mm with suitable railing and fastoon type down shop lead of flexible copper conductor complete having the following components and specification. Note: Size of rails for Crane with fixing arrangements be as per manufacturers design. Coating on rolling surfacrs of the wheels shall be non ferrous. Cost of the same shall be deemed to be included in the cost of crane:(a)Capacity 2Ton(b)Design standard as per IS:3177,807,4137(c) Class/duty-II Indoor type(d)Item-double grider EOT crane(e)Hoist speed-3metre/minute(f)Creep hoist spped-0.3metre per min(g)Cross travel speed-10metre per min(h)Long travel speed-15-20metre per min (j)peration-pendant operated(k)Operation-pendant control(l)Rail span -5 metre(m)Long travel length-10metre(n)Micro speed-3metre per min(o)Height of lift-8metre.

INTERNAL ELECTRIFICATION: Supply and fix Heavy duty Exhaust fan 450mm sweep 1400RPM 230Volts AC 50Hz metal body with copper wound having ISI mark complete all as specified and as directed by the Engineer-in-Charge. Make:- Crompton cat part No EXHD-450-4-1 or equivalent in other approved make.

Supply and fix Exhaust fan 250mm sweep 230Volts AC 50Hz PVC body with copper wound complete all as specified and as directed by the engineer-in-Charge.

Supply and fix LED Tube light 1X20 Watt universal battern type with and including connecting 3 core 1Sqmm PVC insulated multistranded copper conductor color of sheve matching to fitting and connecting from ceiling rose to fitting complete all as specified and as directed by the engineer-in-Charge. Make:- (a) Fitting: Crompton Cat Part No IGP161LT8-16 or equivalent in other approved make (b) Lamp: Crompton Cat Part No LTT8-20 or equivalent in other approved make

Supply and fix Sleek LED light 1X10 Watt 2 feet with and including connecting 3 core 1Sqmm PVC insulated multistranded copper conductor color of sheve matching to fitting and connecting from ceiling rose to fitting complete all as specified and as directed by the engineer-in-Charge. Make:- (a) Fitting: Crompton Cat Part No LDL-10-CDL or equivalent in other approved make (b) Lamp: Crompton Cat Part No LT8-8-562-2 or equivalent in other approved make

Supply and fix Sleek LED light 1X7 Watt 1 feet with and including connecting 3 core 1Sqmm PVC insulated multistranded copper conductor color of sheve matching to fitting and connecting from ceiling rose to fitting complete all as specified and as directed by the engineer-in-Charge. Make:- Fitting with Lamp : Crompton Cat Part No LCL-07-CDL or equivalent in other approved make

Supply and fix Security light fitting pressure die cast alluminium housing heat resistance toughened glass having IP 65 protection of 35Watt complete including fixing with GI Bracket made of 40mm dia GI pipe including fixing clamps etc complete all as specified and as directed by the Engineer-in-Charge. (Make : Philips Model No BRP050LED 036CWR1MFPCS1PSU GR or equivalent in other approved make

Supply and fix High bay light fitting of system efficacy of 125-130lm/W having IP 66 protection of glass & polycarbonate optical cover with pressure die cast housing of 132 watt complete including fixing clamps etc complete all as specified and as directed by the Engineer-in-Charge. (Make :Philips Model No BY 325P LED 160S CW PSU GR FG NB XTFCL V1 or equivalent in other approved make)

Supply and fix Four pole MCCB 100Amps 20KA , ics=icu=100% all as specified and as directed by the engineer-in-Charge.Make: Legrand or equivalent in other approved make

Supply and fix MCB SP 6-32Amps 10KA with chareterestic curve "C" curve all as specified and as directed by the engineer-in-Charge. Make:- Legrand or equivalent in other approved make

Supply and fix VTPN MCCB DB 4 way, 415 volt , double door, IP-43 protection suitable for MCCB 4 pole upto 160A as incomer complete with isolated neutral bar, insulated busbar assembly complete all as specified and as directed by the engineer-in-Charge. Make:- Legrand Cat Part No. 5077 45 or equivalent in other approved make

ADDN/ALTN AND SPECIAL REPAIRS TO E/M:Supply and fix LED tube light fittings 1x20 watt alongwith fixtures complete all as specified and as directed by the Engineer-in-Charge. Make:- Crompton Model No LCTLN-20-CDL or equivalent in other approved make

Supply and fix Surface mounted 40Watt(1 x 4) complete all as specified and as directed by the engineer-in-Charge. Make:- Crompton Model No LCTLSN-40-CDL (1 x 4)or equivalent in other approved make

Supply and fix Flame proof weather proof tube light fixture 2x20watt copmplete all as specified and directed at site. Make: Crompton EXTEN1LT8 16/20 or equivalent in other approved make

Supply and fix LED flood lifght Roof Mounted fitting High bay 70Watt complete all as specified and as directed by the Engineer-in-Charge. (Make : Havells or equivalent in other approved make).

Supply and fix LED flood lifght wall Mounted fitting 70Watt complete all as specified and as directed by the Engineer-in-Charge. (Make : Havells or equivalent in other approved make).

Supply and fix Vertical DB TPN 6 way MCCB as incomer all as specified and as directed by the Engineer-in-Charge. Make:- Legrand Cat Part No. 5077 46 or equivalent in other approved make

Supply and fix Vertical DB TPN 4 way MCCB as incomer all as specified and as directed by the Engineer-in-Charge. Make:- Legrand Cat Part No. 5077 45 or equivalent in other approved make

Supply and fix Four pole MCCB 160Amps 25KA, Ics=100%Icu all as specified and as directed by the Engineer-in-Charge. Make:- Legrand Cat Part No. 4200 57 or equivalent in other approved make

Supply and fix Four pole MCCB 100Amps 25KA, Ics=100%Icu all as specified and as directed by the Engineer-in-Charge. Make:- Legrand Cat Part No. 4200 55 or equivalent in other approved make

Supply and fix Four pole MCCB 63Amps 25KA, Ics=100%Icu all as specified and as directed by the Engineer-in-Charge. Make:- Legrand Cat Part No. 4200 53 or equivalent in other approved make

Supply and fix MCB SP 6-32Amps AC, 240V,10KA "C" curve all as specified and as directed by the Engineer-in-Charge. Make:- Legrand or equivalent in other approved make

Supply and fix MCB SPN 6-32Amps AC, 240V,10KA "C" curve all as specified and as directed by the Engineer-in-Charge. Make:- Legrand or equivalent in other approved make

Supply and fix MCB TPN 6-32Amps AC, 240V,10KA "C" curve all as specified and as directed by the Engineer-in-Charge. Make:- Legrand or equivalent in other approved make

Taking down existing ceiling fan, exhaust fan and air circulators of any sweep from wall/ceiling including connected accessories keeping in safe custody duly maintained record and re-fixing the same in the exact location complete all as specified and as directed by the Engineer-in-Charge.

Taking down existing light fitting of any type & capacity testing and keeping in safe custody and re-fixing the same in the exact location complete all as specified and as directed by the Engineer-in-Charge.

Internal Water Supply :- Supply and fix Stop cock 25mm bore with wall flange ceramic disc cartridge with plain knob complete of make Jaquar cat part No CQT-24081 all as specified and as directed by the Engineer-in-Charge.

Supply and fix Stop cock angular 15mm bore with wall flange complete of make Jaquar Cat part No CQT-23059 all as specified and as directed by the Engineer-in-Charge.

Supply and fix Bip tap with wall flange 15mm complete of make Jaquar Cat part No CQT-23047 or equivalent in Hindware/Cera/Marc all as specified and as directed by the Engineer-in-Charge.

Supply and fix in repair Bip tap with wall flange 15mm complete of make Jaquar Cat part No CQT-23047 or equivalent in Hindware/Cera/Marc all as specified and as directed by the Engineer-in-Charge.

Supply and fix Stainless steel towel rail 600mm long Towel rail shall be all as per Jaquar Cat part No AQN-7711 or equivalent make from list of makes mentioned complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix Health faucet/ hand shower with 8 mm dia, wall hook and easy flexible tube in crome finish1.5m long with nuts complete of make Jaquar cat part No ALD573 and SHA 571 all as specified and as directed by the Engineer-in-Charge.

Material and labour foe DWCPE of 180mm dia(OD) laid in concrete bed complete all as specified and as directed by the Engineer-in-Charge.

PUFF ROOF AND VDF FLOORING: Supply and fix LLOYD PU TR PANEL 60- Prefabricated sandwitch Polyurethane Foam Panels comprising of :- (a) Top sheet: LLOYD PU TR profiled sheets with 35mm crest height at 333mm centres and made out of 0.5mm TCT, 300 Mpa-yield stress, Galvalume steel with 20 micrones of Polyester coating (b)Bottom sheet: Plain sheets with slight ribs and made out of 0.50mm TCT, 300Mpa- yield stress, Galvalume steel with Polyester coating (c)Core: HCFC/CFC free (Zero ODP) Polyurethane Foam having 40(+/-) 2Kg/Cum density in 60mm thick Note:-(i)Lloyd PU TR Panel 60 shall be fixed on to the purlin/Girts with self drilling fastners and with necessary overlap as per manufacturer's specification up to height of 12Mtr as directed by Engineer-in-Charge.(ii)Lloyd PU TR Panel 60 shall be supplied in 1m width and in single length upto 12m without any joints depending on site requirements.

Material and labour for Vaccum dewatering flooring with channel setting, application of floor hardener, levelling screed vibrator vaccum dewatering, rough finish using power floater and smooth finish using power floater all as specified and as directed by the Engineer-in-Charge.

AIR CONDITIONING:-Supply and install in wall split Air conditioner with units indoor/ outdoor, inverter type complete with cordless remote control unit and with inverter technology with maximum star rating and EER of capacity 1.5 TR(100% copper model) all as specified and as directed by the Engineer-in-Charge. Make:- Bluestar Model No.IC718DCTU or equivalent in Carrier/LG

Supply and install in wall split units indoor/ outdoor, inverter type complete with cordless remote controle unit and with inverter technology with maximum star rating and EER of capacity 2 TR(100% copper model) all as specified and as directed by the Engineer-in-Charge.Make:- Bluestar Model No.IC524DATU or equivalent in Carrier/LG

Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variatiuon between 170 v to 270 v with output voltage stabilized at 230 v with accuracy of +- 2.5 % and of capacity 04 KVA all as specified and as directed by the Engineer-in-Charge.

Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variatiuon between 170 v to 270 v with output voltage stabilized at 230 v with accuracy of +- 2.5 % and of capacity 05 KVA all as specified and as directed by the engineer-in-Charge.

Dismantling/disconnecting the existing earth terminal connections, testing and keeping aside safely for reuse for serviceable earthings and reconnection testing complete all as specified and as directed by the engineer-in-Charge.

WATER PURIFICATION :- Supply, installation, commissioning of electronic water purifier system with ozone technology of capacity 100 Ltr/ hr with normal, hot and cold water outlet min (40L+5L+40L)all as specified and as directed by the Engineer-in-Charge. Make: Ozone water purifier system / Best water doctor / Kent or equivalent

Supply and fix Voltage stabilizer for auto operation ,single phase ,naturally air cooled indoor type and designed for input variation between 170V to 250V with out put voltage stablizer at 230V with accuracy with in +/- 2.5% and capacity 2.0 KVA all as specified and as directed by the Engineer-in-Charge.

EXTERNAL ELECTRIC SUPPLY:-Supply laying and testing cable XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 11000 volts grade of size 185 Sqmm 3 core all as specified and as directed by the Engineer-in-Charge.

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (LT panel for TFR)all as specified and as directed by the Engineer-in-Charge. (a) ACB 800 Amp, 4 pole , 50 kA with micro processor release, electrical drawn out - 01 No (b) MCCB 400 Amp 36 KA 4 pole, Ics = 100 % Icu - 01 Nos (c) MCCB 315 Amp 36 KA 4 pole, Ics = 100 % Icu - 02 Nos (d) Aluminium bus bar 1200 Amp TPN - 01 set (e) Indication lamp RYB - 01 set (f) Digital volt meter 0-500 volt with SS - 01 No (g) Digital amp meter with SS 0-800 Amp - 01 No (h) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (main LT panel hull fabrication shop) (a) MCCB 400 Amp 36 KA 4 pole, Ics = 100 % Icu - 01 Nos (b) MCCB 125 Amp 25 KA 4 pole, Ics = 100 % Icu - 02 Nos (c) MCCB 100 Amp 25 KA 4 pole, Ics = 100 % Icu - 02 Nos (d) MCCB 63 Amp 16 KA 4 pole, Ics = 100 % Icu - 02 Nos (e) MCCB 40 Amp 16 KA 4 pole, Ics = 100 % Icu - 03 Nos (f) Aluminium bus bar 600 Amp TPN - 01 set (g) Indication lamp RYB - 01 set (h) Digital volt meter 0-500 volt with SS - 01 No (j) Digital amp meter with SS 0-400 Amp - 01 No (k) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (for hull fabrication shop zone 'A','E' and shipwright annex) (a) MCCB 100 Amp 25 KA 4 pole, Ics = 100 % Icu - 01 Nos (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 05 Nos (c) Aluminium bus bar 200 Amp TPN - 01 set (d) Indication lamp RYB - 01 set (e) Digital volt meter 0-500 volt with SS - 01 No (f) Digital amp meter with SS 0-200 Amp - 01 No (g) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (hull fab shop zone 'B') (a) MCCB 125 Amp 25 KA 4 pole, Ics = 100 % Icu - 01 Nos (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 09 Nos (c) Switch disconnector 4 pole 415 Volt, 63 Amp - 01 Nos (c) Aluminium bus bar 200 Amp TPN - 01 set (d) Indication lamp RYB - 01 set (e) Digital volt meter 0-500 volt with SS - 01 No (f) Digital amp meter with SS 0-200 Amp - 01 No (g) CT of suitable ratio

Supply and fix Switch disconnector 4 pole 415 Volt, 40 Amp - 01 No with enclossure made out of MS sheet 2 mm thick incl locking arrangement and painting(hull fab shop zone 'C') complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix Cable jointing kit for 11KV grade cable for indoor termination heat shirnkable type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 to 185Sqmm all as specified and as directed by the Engineer-in-Charge.

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (hull fab shop zone 'D' & 'F') (a) MCCB 40 Amp 25 KA 4 pole - 01 Nos (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 04 Nos (c) Aluminium bus bar 100 Amp TPN - 01 set (d) Indication lamp RYB - 01 set (e) Digital volt meter 0-500 volt with SS - 01 No (f) Digital amp meter with SS 0-100 Amp - 01 No (g) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (Main LT panel for timber store, annex and saw mill) (a) MCCB 250 Amp 36 KA 4 pole, Ics = 100 % Icu - 01 Nos (b) MCCB 100 Amp 25 KA 4 pole, Ics = 100 % Icu - 02 Nos (c) MCCB 63 Amp 16 KA 4 pole, Ics = 100 % Icu - 02 Nos (d) MCCB 40 Amp 16 KA 4 pole, Ics = 100 % Icu - 01 Nos (e) Aluminium bus bar 400 Amp TPN - 01 set (f) Indication lamp RYB - 01 set (g) Digital volt meter 0-500 volt with SS - 01 No (h) Digital amp meter with SS 0-300 Amp - 01 No (j) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (timber store zone 'A') (a) MCCB 63 Amp 25 KA 4 pole - 01 Nos (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 06 Nos (c) Aluminium bus bar 100 Amp TPN - 01 set (d) MCB SPN 32 Amp (e) Indication lamp RYB - 01 set (f) Digital volt meter 0-500 volt with SS - 01 No (g) Digital amp meter with SS 0-100 Amp - 01 No (h) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (timber store zone 'B') (a) MCCB 63 Amp 25 KA 4 pole, Ics = 100 % Icu - 01 Nos (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 09 Nos (c) Aluminium bus bar 100 Amp TPN - 01 set (d) MCB SPN 32 Amp (e) Indication lamp RYB - 01 set (f) Digital volt meter 0-500 volt with SS - 01 No (g) Digital amp meter with SS 0-100 Amp - 01 No (h) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (saw mill) (a) MCCB 63 Amp 25 KA 4 pole, Ics = 100 % Icu - 01 Nos (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 05 Nos (c) Aluminium bus bar 100 Amp TPN - 01 set (d) MCB SPN 32 Amp (e) Indication lamp RYB - 01 set (f) Digital volt meter 0-500 volt with SS - 01 No (g) Digital amp meter with SS 0-100 Amp - 01 No (h) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (Main LT panel for shipwright office) (a) MCCB 200 Amp 35 KA 4 pole, Ics = 100 % Icu - 01 Nos (b) MCCB 100 Amp 25 KA 4 pole, Ics = 100 % Icu - 02 Nos (c) MCCB 63 Amp 16 KA 4 pole, Ics = 100 % Icu - 02 Nos (d) MCCB 40 Amp 25 KA 4 pole, Ics = 100 % Icu - 01 Nos (e) Aluminium bus bar 300 Amp TPN - 01 set (f) Indication lamp RYB - 01 set (g) Digital volt meter 0-500 volt with SS - 01 No (h) Digital amp meter with SS 0-300 Amp - 01 No (j) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (shipwright office zone 'A') (a) MCCB 40 Amp 25 KA 4 pole, Ics = 100 % Icu - 01 Nos (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 05 Nos (c) Aluminium bus bar 100 Amp TPN - 01 set (d) Indication lamp RYB - 01 set (e) Digital volt meter 0-500 volt with SS - 01 No (f) Digital amp meter with SS 0-100 Amp - 01 No (g) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (shipwright office zone 'B') (a) MCCB 100 Amp 25 KA 4 pole, Ics = 100 % Icu - 01 Nos (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 09 Nos (c) Aluminium bus bar 200 Amp TPN - 01 set (d) Indication lamp RYB - 01 set (e) Digital volt meter 0-500 volt with SS - 01 No (f) Digital amp meter with SS 0-200 Amp - 01 No (g) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (shipwright office zone 'C') (a) MCCB 63 Amp 25 KA 4 pole, Ics = 100 % Icu - 01 Nos (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 08 Nos (c) Aluminium bus bar 100 Amp TPN - 01 set (d) Indication lamp RYB - 01 set (e) Digital volt meter 0-500 volt with SS - 01 No (f) Digital amp meter with SS 0-100 Amp - 01 No (g) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (foundry shop) (a) MCCB 315 Amp 36 KA 4 pole, Ics = 100 % Icu - 01 Nos (b) MCCB 32 Amp 16 KA 4 pole, Ics = 100 % Icu - 02 Nos (c) Switch disconnector 4 pole 415 Volt, 40 Amp - 01 Nos (d) Switch disconnector 4 pole 415 Volt, 250 Amp - 01 Nos (e) MCB SPN 10 Amp - 01 No (e) Aluminium bus bar 500 Amp TPN - 01 set (f) Indication lamp RYB - 01 set (g) Digital volt meter 0-500 volt with SS - 01 No (h) Digital amp meter with SS 0-400 Amp - 01 No (j) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (main LT panel No.1 ICE shop) (a) ACB 800 Amp, 4 pole , 50 kA with micro processor release, electrical drawn out - 01 No (b) MCCB 630 Amp 50 KA 4 pole, Ics = 100 % Icu - 01 Nos (c) MCCB 315 Amp 36 KA 4 pole, Ics = 100 % Icu - 02 Nos (d) MCCB 160 Amp 36 KA 4 pole, Ics = 100 % Icu - 01 Nos (e) MCCB 40 Amp 25 KA 4 pole, Ics = 100 % Icu - 01 Nos (f) Aluminium bus bar 1200 Amp TPN - 01 set (g) Indication lamp RYB - 01 set (h) Digital volt meter 0-500 volt with SS - 01 No (j) Digital amp meter with SS 0-800 Amp - 01 No (k) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (main LT panel No. 2 ICE shop) (a) ACB 800 Amp, 4 pole , 50 kA with micro processor release, electrical drawn out - 01 No (b) MCCB 630 Amp 50 KA 4 pole, Ics = 100 % Icu - 01 Nos (c) MCCB 200 Amp 36 KA 4 pole,Ics = 100 % Icu - 03 Nos (d) MCCB 160 Amp 25 KA 4 pole, Ics = 100 % Icu - 02 Nos (e) Aluminium bus bar 1200 Amp TPN - 01 set (f) Indication lamp RYB - 01 set (g) Digital volt meter 0-500 volt with SS - 01 No (h) Digital amp meter with SS 0-800 Amp - 01 No (j) CT of suitable ratio

Supply, Install, testing and commissioning of feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (ICE shop zone 'A') (a) MCCB 315 Amp 25 KA 4 pole,Ics = 100 % Icu - 01 Nos (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 08 Nos (c) Switch disconnector 4 pole 415 Volt, 125 Amp - 01 Nos (c) Aluminium bus bar 500 Amp TPN - 01 set (d) Indication lamp RYB - 01 set (e) Digital volt meter 0-500 volt with SS - 01 No (f) Digital amp meter with SS 0-400 Amp - 01 No (g) CT of suitable ratio

Supply, install, testing and commissioning of feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (ICE shop zone 'B') (a) MCCB 630 Amp 50 KA 4 pole,Ics = 100 % Icu - 01 No (b) Switch disconnector 4 pole 415 Volt, 630 Amp - 01 No (c) Switch disconnector 4 pole 415 Volt, 80 Amp - 02 No (d) Switch disconnector 4 pole 415 Volt, 40 Amp - 04 Nos (e) Aluminium bus bar 1000 Amp TPN - 01 set (f) Indication lamp RYB - 01 set (g) Digital volt meter 0-500 volt with SS - 01 No (h) Digital amp meter with SS 0-600 Amp - 01 No (j) CT of suitable ratio

Supply , Install, testing and commissioning of feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (ICE shop zone 'C') (a) MCCB 200 Amp 36 KA 4 pole, Ics = 100 % Icu - 01 No (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 08 Nos (c) Aluminium bus bar 300 Amp TPN - 01 set (d) Indication lamp RYB - 01 set (e) Digital volt meter 0-500 volt with SS - 01 No (f) Digital amp meter with SS 0-200 Amp - 01 No (g) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (ICE shop zone 'D') (a) MCCB 630 Amp 50 KA 4 pole,Ics = 100 % Icu - 01 No (b) Switch disconnector 4 pole 415 Volt, 400 Amp - 01 No (c) Switch disconnector 4 pole 415 Volt, 160 Amp - 02 No (d) Switch disconnector 4 pole 415 Volt, 40 Amp - 04 Nos (e) Aluminium bus bar 1000 Amp TPN - 01 set (f) Indication lamp RYB - 01 set (g) Digital volt meter 0-500 volt with SS - 01 No (h) Digital amp meter with SS 0-600 Amp - 01 No (j) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangmens (ICE shop zone 'E') (a) MCCB 200 Amp 36 KA 4 pole,Ics = 100 % Icu - 01 No (b) Switch disconnector 4 pole 415 Volt, 125 Amp - 01 No (c) Switch disconnector 4 pole 415 Volt, 40 Amp - 08 Nos (d) Aluminium bus bar 300 Amp TPN - 01 set (e) Indication lamp RYB - 01 set (f) Digital volt meter 0-500 volt with SS - 01 No (g) Digital amp meter with SS 0-200 Amp - 01 No (h) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (main LT panel for R & AC shop) (a) MCCB 100 Amp 25 KA 4 pole,Ics = 100 % Icu - 01 No (b) MCCB 63 Amp 16 KA 4 pole, Ics = 100 % Icu - 01 No (c) Switch disconnector 4 pole 415 Volt, 40 Amp - 10 Nos (d) Aluminium bus bar 200 Amp TPN - 01 set (e) Indication lamp RYB - 01 set (f) Digital volt meter 0-500 volt with SS - 01 No (g) Digital amp meter with SS 0-100 Amp - 01 No (h) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (main LT panel electrical shop) (a) MCCB 400 Amp 36 KA 4 pole, Ics = 100 % Icu - 01 No (b) MCCB 160 Amp 25 KA 4 pole, Ics = 100 % Icu - 02 No (c) MCCB 100 Amp 25 KA 4 pole, Ics = 100 % Icu - 02 Nos (d) MCCB 63 Amp 16 KA 4 pole, Ics = 100 % Icu - 03 Nos (e) Aluminium bus bar 500 Amp TPN - 01 set (f) Indication lamp RYB - 01 set (g) Digital volt meter 0-500 volt with SS - 01 No (h) Digital amp meter with SS 0-400 Amp - 01 No (j) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (electrical shop zone 'A') (a) MCCB 63 Amp 25 KA 4 pole,Ics = 100 % Icu - 01 No (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 07 Nos (c) Aluminium bus bar 100 Amp TPN - 01 set (d) Indication lamp RYB - 01 set (e) Digital volt meter 0-500 volt with SS - 01 No (f) Digital amp meter with SS 0-100 Amp - 01 No100/5 Amp - Set of 03 Nos

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (electrical shop zone 'B') (a) MCCB 160 Amp 35 KA 4 pole, Ics = 100 % Icu - 01 No (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 09 Nos (c) Aluminium bus bar 250 Amp TPN - 01 set (d) Indication lamp RYB - 01 set (e) Digital volt meter 0-500 volt with SS - 01 No (f) Digital amp meter with SS 0-100 Amp - 01 No (g) CT of suitable ratio

Supply and fix feeder pillar box indoor type made out of MS sheet 2 mm thick welded on angle iron frame 40 x 40 x 6 mm duly grouted in earth/floor or as required incl PCC 1:3:6 type C-1 with locking arrangement and painting with powder coated, smoke gray paint including following accessories suitable for incoming/out going arrangments (electrical shop zone 'C' & 'D') (a) MCCB 63 Amp 25 KA 4 pole, Ics = 100 % Icu - 01 No (b) Switch disconnector 4 pole 415 Volt, 40 Amp - 06 Nos (d) Aluminium bus bar 100 Amp TPN - 01 set (e) Indication lamp RYB - 01 set (f) Digital volt meter 0-500 volt with SS - 01 No (g) Digital amp meter with SS 0-100 Amp - 01 No (h) CT of suitable ratio

Supply and fix rubber mat 1 Mtr x 2 Mtr x 10 mm all as specified and as directed by the Engineer-in-Charge.

Supply, Laying and testing UG cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volt with screened aluminium conductor of size 3.5 core 400 Sqmm all as specified and as directed by the Engineer-in-Charge.

All as per Item No 138 herein before but 3.5 core 300 Sqmm

All as per Item No 138 herein before but 3.5 core 240 Sqmm

All as per Item No 138 herein before but 3.5 core 185 Sqmm

All as per Item No 138 herein before but 3.5 core 120 Sqmm

All as per Item No 138 herein before but 3.5 core 70 Sqmm

All as per Item No 138 herein before but 3.5 core 35 Sqmm

All as per Item No 138 herein before but 4 core 25 Sqmm

All as per Item No 138 herein before but 4 core 16 Sqmm

All as per Item No 138 herein before but 2 core 16 Sqmm

Supply, spreading and levelling riddled soil as earth cushioning to UG cable by using IS seive to seperate the composite/roots etc and refilling spreading in trenches as cushioning and rammed down to form a solid bed all as specified and directed at site. Note:- Punned thickness shall only be measured and paid.

Cutting of Road ( in hard/dense soil) for laying of Electric cable of any size upto max 01 mtr depth and getting out including forming bottom surface to required level or slope & making good the distrubed existing complete all as specified and as directed by the Engineer-in-Charge.

Dismentaling/disconnecting the existing earth connection, testing and keeping aside safe for found servicebale and reconnection & testing complete all as specified and directed

Powertech Engineers

Hemant Construction Co.