Provision of CCTV Cameras at Non-Interlocked Manned LC Gates at different locations over DDU division.

1- Provision of CCTV Cameras at Non-Interlocked Manned LC Gates at

Supply, Installation, Testing & Commissioning of Full HD Fixed Bullet type IP Colour 1 Camera along with 128 GB or higher SD Card, housing and mount and all accessories required for installation purposes As Per RDSO specification No RDSO/SPN/TC/65 /2021Version 6.0 or latest. It should be STQC complied. Execution of work as instruction of site engineer. Inspection - RDSO

Supply, Installation,Testing & Commissioning of Field Switch 8-POE port and 2 Nos of 2 1G Optical port (required SFP module is also required to be provided) as per Spec. No: RDSO/SPN/TC/65/2021 Ver.6.0 or latest. Execution of work as instruction of site engineer. Inspection - RDSO

Supply of Rack mounter 8 channel NVR , IP camera support, PTZ camera control 3 support, Full HD(1920 X 1080) Recording Resolution, H.264,H.265,MPEG-4 Compression Technique, Recording Speed:25fps, Ethernet, HDMI, VGA,USB Supported Interface-Upto 6TB capacity for each disk, Make: Sparsh,CP-plus or Prama. Inspection- RDSO.

Supply & Installation of Surveillance Hard Disk Drive 4 TB capacity As per technical specification attached as Annexure-1. Execution of work as instruction of site engineer. Inspection- Consignee

Supply & Installation of 64 Channel Network Video Recoder and 64TB storage after 5 RAID 5/6 configuration with HDD(8 nos. of HDD capacity 8TB each), 2 nos. ethernet complete with all other accessories as per RDSO spec. No: RDSO/SPN/TC /65/2019 Rev.5.0 or latest. Execution of work as instruction of site engineer. Inspection - RDSO

Supply of 22" LED Monitor, Make Dell/Samsung/HP/Acer or better. Inspection- Consignee.

Supply of 4K UHD Display (55 inch) as per RDSO spec. No: RDSO/SPN/TC/65 /2021 Rev.6.0 or latest . Inspection- Consignee.

Installation, Testing & Commissioning of Full HD Large Format Display Monitor (55 inch).All the accessories and fixing materials required for this installation are to be supplied by contractor within the same cost. Execution of work as instruction of site engineer.

Supply of On line pure sine wave UPS of 1KVA with SMF batteries. Minimum 1600VAH for backup of one hour. Make - Microtek, Eton or APC. As per technical specification attached as Annexure-1 Inspection- Consignee.

Supply of Integrated service router with 3 onboard GE, 2 NIM Slots, 1 ISC slot, 1 SM 10 slots, 4 GB Flash Memory default, 4 GB DRAM default loaded with 8 port Multi-flex Trunk Voice/Clear- channel Data T1/E1 Module. Dual power supply support(230V AC/48V DC). Make-Cisco ISR 4331 with NIM-8MFT-T1/E1 module or similar. As per technical specification attached as Annexure-1. Inspection - RITES.

Supply of Wireless Portable Router for internet connectivity with Integrated SIMcard 11 slot High-speed 4G LTE/VoLTEconnections with downlink speed up to150 Mbps and uplink speeds up to 50Mbps, Wi-Fi speeds up to 300 Mbps FastEthernet WAN port, and four Fast Ethernet LAN ports. Make- D link or similar. Inspection- Consignee.

Supply and installation of with one Sim Card with one-year internet subscription. Execution of work as instruction of site engineer. Inspection- Consignee.

Supply and Installation of surface Wall mountable type 19 inch 6U network Rack with 13 front glass door with lock and rack fixing multipoint AC Power trip & all accessories.As per technical specification attached as Annexure-1. Execution of work as instruction of site engineer. Inspection- Consignee.

Supply of RJ-45 connector. Make - Dlink or similar. As per technical specification attached as Annexure-1. Inspection- Consignee.

Supply of Single Mode 10/100/1000 media convertor with latest Technology , Make - Syrotech, D-link, Techroute or better. Inspection- Consignee.

Supply of Simplex Single Mode Optical Fiber Patch Cord 9/125 Jumper Cable 5 Meters 15 ft (SC/APC - SC/APC, LC-SC/SC-SC/LC-LC/FC-LC or as per site requirement) Make- Syrotech, D-link, Techroute or better. Inspection- Consignee.

Supply of PIG Tail (10m Long) with FC/PC connector as per TEC specification no. G/OFJ-01/03 Jun'99 with latest amendments. (required accessories like 0dB etc. connector to be supplied by contractor). Inspection- RITES.

Supply and fixing of ISI mark PVC conduit pipe of 25mm diameter and 1.5mm thickness. Execution of work as instruction of site engineer. Inspection- Consignee.

Supply of STP CAT-6 cable.Cable should be compliant with latest EIA/TIA-568-B. 2-1 standard with fire retardant as per IEC/EN60332-1. As per technical specification attached as Annexure-1. Inspection- Consignee.

Supply of 6 Fiber armoured mono mode optical fiber cable. As per technical specification attached as Annexure-1. Inspection- Consignee.

Supply of power cable 3 Core copperx(PVC insulated flexible 3 core x 2.5 sq mm multi strand power cables should conform to specification no. IS: 694:1990 reaffirmed 1995 or latest.) Make: Delton /Finolex or better. Inspection- Consignee.

Fixing of GI pipe of sizes as given below for entry of cables on bridges/ culverts/drains approaches or at places as adviced by the site incharge of Railways. The GI pipe should be tightly 22 clamped with suitable clamp as per instruction of Railway site engineer. Proper bricks channel and concreting (1:2:4) is require to be made for cases of requirment of site over GI pipe by a layer of 100 mm and extending by 60 mm. dia /80 mm dia PVC/HDPE pipe on either side minimum by 01 mtr. The rate is given for fixing of one GI pipe including supply of GI pipe, PVC/HDPE pipe and other materials required for execution. (i) 50 mm dia. Note - GI pipe 50/70 mm. dia Grade medium as per IS : 1239 Pt. 1 1979 (70 mm dia grade medium as per IS 1239 Pt. 1 1979) and flexible PVC/HDPE pipe 60/80 mm. dia with clamps, bricks and the materials for concreting and fixing the pipe are to be supplied by the contractor at site after inspection by the rep. of Railway. Execution of work as instruction of site engineer. Cubic

Casting,cementing & concreting with cement,sand & stone chips (12.5mm) in the ratio 1:2:4.(all materials are to be supplied by the contractor). Execution of work as instruction of site engineer.

Supply of DWC pipes (ISI mark) confirming to Sepc no. IS-14930,part -II of length 6 24 meter and 120mm outer and 103.5mm inner dia. with one snap fit coupler with rubber ring,spacer,band ,endcap one v end and one T coupler for under ground power/signal/Tlecom cable protection.Make-Rex,Duraline, or Similar. Inspection - RITES.

Installation of Double Wall corrugated (DWC) pipe with socket coupler.The includes (1.2 mtrs) Depth and backfilling. Execution of work as instruction of site engineer.

Supply and laying of HDPE Pipe / Telecom duct (Outer dia 40 mm) as per generic 26 requirement No. G/COS-08/01 DEC'99 or latest at a depth of 1.0 metre in all kind of soils. This includes transportation of HDPE pipe / Telecom duct to the site. Execution of work as instruction of site engineer. (Inspection - RITES)

Supply and installation of Joint enclosure and making of straight through joints including splicing and making Pit of size 1.2 metre (depth) and 1.2 metre dia in all type of soil in the 27 section, back filling the pit after jointing and coilling of 10 metres OFC cable (as reserve / spare). Provision of bricks walling around the sides and bottom of the pit with 1:6 plaster covering the pit with RCC slab, back filling with earth after ramming as per drawing. All the materials requires for OFC joints & pit construction will be supplied by the contractor. Execution of work as instruction of site engineer. Inspection - Consignee.

Supply and Installation of fiber distribution frame 19" rack mounted as per 28 specification no. IRS:TC:81-2000 (Part-D) or 48 fibers (24 fibers from each side) including supply of all pig tail / patch cord / FCFC adopter. Execution of work as instruction of site engineer. Inspection - RITES

Splicing /Dropping/Termination of eachFiber /Pigtail in the LIU/FDMS/Termination Joints through fusion Splicing of the termination of OFC Cables. Execution of work as instruction of site engineer.

Supply and installation of RCC Route Markers including Painting As per technical specification attached as Annexure-1.Execution of work as instruction of site engineer. Inspection- Consignee.

Supply and fixing of PVC Casing and caping of 50 mm x 50 mm x I.5 mm thickness 31 with cover on wall/Roof/Partition etc as per IS 14927 Part 1 or latest (All the miscellaneous materials required for fixing to be supplied by the contractor). Execution of work as instruction of site engineer. Inspection- Consignee.

Supply and erection of 15 feet GI pipe of 4'' dia of medium quality ISI No 1230 (part 1) 1990.Having iron base plate 10mm thick 30cm x 30cm weild at the bottom of the pipe with 4 supports of iron bars of size 10mm dia. The 3 feet pipe shall be burried in the ground and 12 feet shall be above the ground. The work includes digging of pit on platform, laying of cable, erection of pole, filling the pit with 1:3:4 cement, concrete and sand. Final plastering should be done on the surface. The iron bracket on the top of the pole shall be provided for the fixing of CCTV camera and junction box/6U outdoor cabinate etc.(Necessary fixing and other materials required for fixing should be brone by the contractor). Execution of work as instruction of site engineer. Inspection- Consignee.

"Digging trench 1.0 Mtr deep & 0.3 Mtr wide in all kind of soil , dully clearing any 33 roots, plants etc. The trench should be straight and parallel to track as per RE specification. . If the depth of the trench not uniform in a span of 100 Mtr of shortest length and site condition demands along the cable run, minimum depth will be taken for that particular stretch for payment. Execution of work as per site engineer

"Back filling of trench by shifted earth and ramming of the earth up to original ground level after the work Execution of work as per site engineer

Laying of OFC through HDPE pipe / Telecom duct by blowing of OFC as per procedure and practise in Railway and advised by site engineer.

Blowing/ Drawing/ Laying of 6-F OFC/ Power Cable / CAT-6 cable in trenches / GI pipe/ 36 through HDPE pipe on ground or on wall for connecting/ interfacing various components for system integration of CCTV surveillance system and others. This includes supply and installation of Fibre management system (wherever required), splicing, and termination of the fibres. Execution of work as instruction of site engineer.

Cutting of platform surface (Tile/Slab) for a depth of 25cm and a width of 10cms and 37 refilling /Reconditioning/ Concreting /Repairing the platform after laying HDPE/PVC pipe and cable. Cutting should be done with marble cutting machine in proper manner and restore the same as before in such a manner that aesthetic of the platform is not disturbed. (Laying of pipes/cables not included), Execution of work as instruction of site engineer.

Excavation, trenching, earth work and reinstatement of track while track crossing. Execution of work as instruction of site engineer.

Cable Crossing Rly. Track / Road by boring hole at a depth of 1 meter by using one no. 100 mm dia G.I pipe (medium grade) with accessories. G.I pipe with accessories will be supplied by contractor.Execution of work as instruction of site engineer.

Transportation of HDT machine with accessories including handling of stores materials, preparation of site and boring of 110mm dia and placing HDPE pipe of size 63 to 40mm in single / double / triple etc required for crossing/ laying of Railway cables in a combination of quad & signalling cables etc. as per required comprising maximum 72 cores in any HDD section on land /bridges / culverts / track / pucca road crossing and blowing / pulling of Quad / Signalling cables etc. within HDPE pipe. Boring of trench shall be minimum 1(one) Mtr below the track to 1.5 (one point five) minimum 3 (three) meter below the river bed, 01 meter below other lands including road / pucca road 63 to 40 mm dia & its accessories suitable for HDT as permanently lubricated HDPE pipe 40 of size 63 to 40mm crossing area. This includes supply as per Specification No. RDSO/SPN/TC/45 /2013 with latest amendment & cost of the fuel and all other items which will be required for laying of cable through it. Inspection : RITES for HDPE pipe (for inspection charges cost of all sort of HDPE pipe is Rs. 195/- per Mtr.) NOTE: The number of HDPE pipes (of any dia as mentioned above) to be pulled in any HDD section will depend upon the numbers of quad / signalling cables to be pulled through that HDD section as per site requirement. At a particular site, the second /additional HDD is to be done only after completing the pulling of 72 cores of cable through 1st HDD other wise the second /additional HDD will not be counted as a new / additional HDD for the purpose of billing. Only cables to be supplied by Railway. Cable sketch/route plan showing division & depth to be submitted by firm.Execution of work as instruction of site engineer.

"Supply and Installation of basic material to construct unit maintenance free earth as per RDSO Spc.No.RDSO/SPN/ 197/ 2008 or latest, consisting the following (Inspection:Supply Portion- 41 RDSO) (i) Copper bonded steel electrodes of 3.0 meter long & 17.0 mm dia with Cu-bondign thickness of min. 250 microns and UL listed and marked =1 no. (ii) Earth enhancement material supplied in sealed bags of min. 10 Kgs =3 nos. (iii) Cu-strip 150x25x6 mm to terminate earth rod=1 no.(iv) Cu-strip 300x25x6 mm (MEEB)=1 no.(v) Cu-strip 150x25x6 mm (SEEB)=1 no.(vi) digging the earth to the required depth(vii) Insertion of electrode(viii) Filling of earth enhancing compound (30 Kg) provision of exothermic weld connection on copper tape/bus bar of 25 mm x 6mm x 150 mm to the earth electrodes all the materials, tools and features required for the weld to be arranged by the contractor-1 no.(ix) Trenching, laying & provision of exothermic weld connecting, one to connect copper tape/35 sq mm multi strand single core PVC insulated copper cable to the copper strip/tape/ busbar welded to the earth electrode and another to the copper tape to be fixed inside the equipment/relay rack/apparatus room as per RDSO's Spec (fixtures for mounting the copper tape inside the relay room, weld materials, tool features and all other materials required for the weld shall be arranged by the (x) Exothermic weld connection, fixing of Cu- strips and routing the cables to bus bar in equipment/relay room (all other materials requird for the work shall be borne by the contractor.(xi) Construction of concrete inspection chamber as per RDSO spec.(xii) Any other material said required as per RDSO spec.NOTE:(i) Above includes interconnection of the earthing installed with the already existing earthing electrode, if any, as per site requirement and as per instruction of site incharge. (2) Any other material required as per RDSO spec. (3) All materials required for compelete installation of maintenance free earth, to be supplied by the contractor. "Execution of work as instruction of site engineer. Execution of work as instruction of site engineer.

Supply and installation of Class "B" & Class "C" lightning cum surge protection device 42 for main incoming power supply with enclosure as per RDSO spec. RDSO/SPN/165/2012 (Ver.3) or latest . Material to be produced from RDSO approved/recommended sources only.Execution of work as instruction of site engineer. Inspection- RDSO.

Supply of Optical Time Domain Reflectometer (OTDR) for 1310/1550nm fiber with 43 resolution of 60 Cms,dynamic Rangeof 314/29 dB with all accessories confirming to TEC Specification NoTEC Specification No G/OTD/02-03 March 2009.Make EXFO Model MAX 720C , AQ- 7270+735022.Make Yokogawa Electric Co Ltd Japan or better .Inspection- RITES.

Supply of Single fiber fusion splicing machine similar to fujikura 80C with standard accessories :AC ADAPTER /BATTERY Charger, AC Power Cord, Spare Electrode, Carrying case, USB 44 cable, Sleeve loader, Dispenser, Screw driver, BATTERY PACK, Battery charger cord, High precision Fiber cleaver, 3 in-1 Stripper & Protection sleeves (A demo shall be arranged along with supply) as per TEC Specification g/osm/01-03 April 2005 Model S-177A. Make - FURUKAWA ELECTRIC COJapan. Type approved or Superior. Inspection- RITES.

Supply of electronic Cable route tracer/locator with underground cable and pipe 45 locating receiver and cable avoidance tool thatprovide location of armoured OFC ,signalling and telecom , powercable etc. make : C Scope Stanley/3M Dynatel , model: DXL-4DBG /2273M-iD 30 or superior. Inspection- RITES.

Supply of Handheld Digital Earth Clamp Tester for clamp on earth/ground resistance 46 measurement up to 1000 ohms.Accuracy 0.1 - 0.99 : 1%, 1 - 49 :1.5% Also measure current leakage up to 20A. No spines required formeasurement Model - DECT-2 orequivalent / higher version make Motwane/Stanlay /Fluke/Megger. Inspection- Consignee.

Supply and testing of optical Laser light source of Make- JDSU ModelOLS-35 or latest or having similar specification of reputed make. Inspection- Consignee.

Supply of Wiremap Tester(Network Microscanner CableTester) for CAT-6 and CAT- 5Cable Make Fluke Modelno.MS2-100 or equivalent As per technical specification attached as Annexure-1. Inspection: Consignee.

Supply of Optical Power Meter,type-B, as per TEC spec. GR/OPM-01/03 Feb. 2005 or latest. Inspection- Consignee.

Supply of Digital multimeter for diagnosis & measuring parameter; Make:Fluke 107 or KYORITSU KEW1019R or Klein Tools MM1300. Inspection- Consignee.

Supply of digital Psophometer as per specification are as under, Frequency Range - 51 15Hz to 6KHz (Weighted Mode) as specified by CCITT & 15Hz to 10KHz (Unweighted Mode); Measuring Range -90dBm to 0dBm & 30 micro V to 1V; Min. Measurable Value 10 micro V (-98dBm); Calibration Accuracy at 800Hz - 0 to -60dBm: ±0.5dB & -60 to -90dBm: ±1.0dB; 3½ Digit LCD type Display; Input Impedance - 600 ohms, 1120 ohms balanced, Recorder Facility; Power-100 micro A at 0dBm 1120 impedance, 230V AC ±10%, 47-53Hz. Optional 115V AC ±10%, 57-63Hz. Internal rechargeable 6V battery. External battery operation. Make-Aplab 1072 or better. Inspection- Consignee.

CAMC of CCTV camera system installed at above LC Gates and related equipment installed at connecting station including CAMC of 1 KVA Off-Grid Solar Photovotaic (PV) Power Plant, installed for CCTV system by Railway