Creation of office space in A-09 block of North campus for Dean students, Dean faculty, SRIC and IR, Dean Academic and DORA

Amount

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form for: Shelves (Cast in situ) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form for: Edges of slabs and breaks in floors and walls. Under 20 cm wide as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and pre-polished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. Area of slab over 0.50 sqm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing aluminum extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete as per entire satisfaction and direction of Engineer -in-charge including carriage of material in all lead and lift.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing factory made uPVC white colour sliding glazed window up to 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dashfastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugsat 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.45.1 12.5 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and Fixing 15 mm thick densified tegular edged eco-friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

CEMENT PLASTER (IN FINE SAND) 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water thinnable priming coat with cement primer as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Distempering with 1st quality acrylic distemper (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade : Old work (one or more coats) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length. 15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing PTMT grating of approved quality and colour. Circular type 100 mm nominal dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately): For fixed portion. Powder coated aluminium (minimum thickness of powder coating 50 micron) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coating 50 micron) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved esign/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non- staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so asto make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Designing, providing, installing and fixing factory finished custom designed cold form Light Gauge Steel Framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 1.15 mm thick steel sheet as per design requirements. The steel sheet shall be galvanized (AZ-150gms Aluminium Zinc Alloy coated steel having minimum yield strength 300-550 Mpa) conforming to AISI specifications and IBC 2009 for cold formed steel framing and construction and also as per IS: 875-1987, ISO 800-1984 and IS:801-1975. The wind load shall be as per provisions of IS 875 (part -III). LGSFS frame shall be designed as per IS: 801 using commercially available software such as Frame CAD Pro-11.7/ STAAD PRO-V8i/ ArchitekV2.5.16/ Revit architecture-2011 or equivalent. Proper usage of Connection Accessories like Heavy Duty Tension Ties, Light Duty Hold-ons, Twist Straps (to connect truss with wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing Sections, L-Shaped Angles for better structural stability. The framing section shall be cold form C-type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple/ slot at required locations as per approved drawings. The slots will be along centre line of webs and shall be spaced minimum 250mm away from both ends of the member. The frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. All self drilling tapping screws for joining the members shall have a Type II coating in accordance with ASTM B633(13) or equivalent corrosion protection of gauge 10 & 12, TPI 16 & 8 of length 20mm. The frames shall be fixed to RCC slab or Tie beam over Neoprene rubber using self-expanding carbon steel anchor bolt of dia as per approved drawings. design subject to minimum 12mm diameter and 121mm length conforming to AISI 304 and 316 at 500mm c/c with minimum embedment of 100mm in RCC (RCC to be paid separately) and located not more than 300mm from corners or termination of bottom tracks complete in all respects. The item also includes the submission of stability reports duly examined and issued by any NIT/IIT. The rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing internal wall panels on Light gauge steel frame work with 12.5mm thick gypsum plaster board conforming IS 2095:2011 fixed on cement board as per standard sizes fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make, Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately. Cement Fiber Board 8 mm thick as per IS 14862:2000 of type B (High pressure Steam Cured) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing S S 304 grade door handle set for fully glazzed door including necessary cutting, hole, fixing accessories and making good etc. all complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing S S 304 grade double shed glass door lock glass to glass 100mm padlock for Fully glazzed door including necessary cutting, hole, fixing accessories and making good etc. all complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing aluminium handles, ISI marked, power coated (coating not less than grade AC 10 as pern IS:1868) transparent or dyed to required colour or shade, with necessary screws etc. complete 200 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and Fixing ROLLER BLINDS & complete with all component, including drilling holes in the wood work/RCC & installation at site. The Roller Blinds will have following specifications:Top channel extruded from Non rusting Aluminum alloy with 1.25 mm thickness, with anodization for long life. The Channel is designed with support beam to keep it straight and shall have a pocket for holding the fabrics in position. Available in 32 & 38 mm diameters for small and big blind respectively. Bottom Channel of Roller Blinds is again none rusting Aluminum powder coated with 1.50 mm thickness and 21 mm diameter. The fabric is enclosed in suitably created pocket along with tube. The channel shall be closed from sides with the end caps to give a neat look. Matching colors of bottom channel available to match with the fabrics. The tilt chain is made of unbreakable ABS plastic, 1.50 mm polyester cord with 4.50 mm balls. The blind can be stopped of desired position with help of stop lock. This operating mechanism is made of High strength ABS plastic, consists of an ultra smooth gear with spring booster. High carbon steel spring to transmit motion from driver to driven members. The mechanism shall be operating with the use of tilt chain. The Brackets are made of steel with powder coating to give smooth finish. Brackets shall be accommodated overhead or on side mounting with clutch assembly on either end of the blind. Fabric Specifications: Proton Blackout Composition of Fab.100 % Polyester Visibility Zero Light Transparent Zero Available Width 2.60 Mtrs Fabric Thickness 0.45 MM (+-0.05)Weight325 g/m2 (+-5%)Tearing Strength Very High Hanging Properties Excellent Cleaning Conditionally cleanable with damp cloth as per entire satisfaction and direction of Engineer -in-charge including carriage of material in all lead and lift.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 8mm thick heavy duty fiber cement board as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and Fixing ZEBRA ROLLER BLINDS (Blackout) & complete with all component, including drilling holes in the wood work/RCC & installation at site. The ZEBRA Roller Blinds will have following specifications:- With double-ply screen, which can be Adjust easily, the curtain surface is processed by dustprrof and antistatic UV Protection: 90%-95% (when close the blind), Top channel extruded from Non rusting Aluminum alloy with 1.25 mm thickness, with anodization for long life. The Channel is designed with support beam to keep it straight and shall have a pocket for holding the fabrics in position. Available in 32 & 38 mm diameters for small and big blind respectively. Bottom Channel of ZEBRA Roller Blinds is again none rusting Aluminum powder coated with 1.50 mm thickness and 21 mm diameter. The fabric is enclosed in suitably created pocket along with tube. The channel shall be closed from sides with the end caps to give a neat look. Matching colors of bottom channel available to match with the fabrics. The tilt chain is made of unbreakable ABS plastic, 1.50 mm polyester cord with 4.50 mm balls. The blind can be stopped of desired position with help of stop lock. This operating mechanism is made of High strength ABS plastic, consists of an ultra smooth gear with spring booster. High carbon steel spring to transmit motion from driver to driven members. The mechanism shall be operating with the use of tilt chain. The Brackets are made of steel with powder coating to give smooth finish. Brackets shall be accommodated overhead or on side mounting with clutch assembly on either end of the blind. Fabric Specifications: Proton Blackout, Composition of Fabric 100 % Polyester and voile/linen and voile, Visibility Zero Light Transparent Zero Available Width 2.60 Mtrs Fabric Thickness 0.45 MM (+-0.05)Weight325 g/m2 (+-5%)Tearing Strength Very High Hanging Properties Excellent Cleaning Conditionally cleanable with damp cloth as per entire satisfaction and direction of Engineer -in-charge including carriage of material in all lead and lift.

Electrical Work Wiring for light point/ fan point/ exhaust fan point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and drawing 3x1.5 sq mm of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed PVC conduit as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and drawing 3x2.5sq mm of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed PVC conduit/Wall Trunk/Casing as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and drawing 3x4 sq mm of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed PVC conduit/Wall Trunk/Casing as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing of 20 sq mm of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing of 25 sq mm of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 5/6 A Switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 15/16 A switch modular switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 3 pin 5/6 A socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 6 pin 15/16 A socket outlet modular socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 3 Module Modular base & cover plate on existing modular metal/PVC boxes etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 4 Module Modular base & cover plate on existing modular metal/PVC boxes etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 6 Module Modular base & cover plate on existing modular metal/PVC boxes etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 8 Module Modular base & cover plate on existing modular metal/PVC boxes etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 12 Module Modular base & cover plate on existing modular metal/PVC boxes etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing 16 mm M.S. Fan clamps of standard shape and size in existing R.C.C. slab, including cutting chase, anchoring clamp to reinforcement bar, including cleaning, refilling, making good the chase with matching concrete, plastering and painting the exposed portion of the clamps complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 12 way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. (But without MCB/RCCB/Isolator) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 6 way (8 + 24), Double door horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing Single pole 5 to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of Single pole, in the existing MCB DB complete with connections, testing and commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 63 A rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 40 A rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 40 A rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of up to 35 Sq. mm size on Cable Tray (Clamped with 1 mm thick saddle) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of Thickness 0.63 mm sheet sheet thickness complete as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and making end termination with brass compression gland and aluminium lugs for 3 X 16 sq. mm (25mm) size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying of 3 Core 16 Sq. mm of 1.1 KV Cu conductor XLPE Insulated,PVC extruded inner-sheathed, round wired GI strip armoured, overall PVC outer-sheathed (as per IS 7098 Part 1) with latest amendments as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying, Installation, testing and commissioning of pre-wired, Square Recess Down Lighter(595x595 mm) of Wattage 36 W (6500K) directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 4 Module PVC box to be fixed in the existing Wall Trunking as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 3 Module PVC box in open surface/wall as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 6 Module PVC box to be fixed in the existing Wall Trunking as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 8 Module PVC box in open surface/wall as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 12 Module GI box in open surface/wall as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Dismantling of ceiling fan including cleaning of surface with Cotton Cloth and replacing the damaged rubber reel, nuts and bolts with washers and safety pins refixing the same as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Dismantling and Cleaning of Surface Down Lighter with Cotton Cloth with full precaution taken as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying of GI fan rod of length up to 2.5 m per fan as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying, Installation, testing and commissioning of pre-wired, Round Recessed Down 15 Watts Light (150 mm) directly on ceiling, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying, Installation, testing and commissioning of 20W LED Tube Light (1200 mm) with colour temprature 6000K and Above directly on Wall including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and Installation of Walll fan (400 mm ) in White Colour as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing of 20 mm size of medium class PVC Casing-Capping along with accessories in surface as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing of 25 mm size of medium class PVC Casing-Capping along with accessories in surface as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and making end termination with brass compression gland and Copper lugs for 4 X 6 sq. mm size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying of 4 Core x 6 Sq. mm of 1.1 KV Copper conductor XLPE Insulated, PVC extruded inner-sheathed, round wired unarmoured, overall PVC outer-sheathed (as per IS 7098 Part 1) with latest amendments as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Nipani Infra And Industries Pvt Ltd