Provn of certain Minor wk and Revenue works under GE Dehradun

Amount

Supplying, erecting, testing and commissioning Raising & Lowering type 15 meter or next higher available height mast system hot dip galvanised (inside and out side ) in single dip , suitable for wind velocity as per IS 875 part 3 with only one longitudinal seam weld per section but without circumferential weld including accessories viz head frame 2- point suspension system sith steel wire rope 6mm dia (7/19 guage) construction, trailing cable, double drum winch, galvanised lantern carriage arrangement suitable for 9 luminaries symetrically ,lightning finial , aviation obstruction light ,RCC foundation bolts,nuts, anchor plates, templates, trailing cable and intergral power tool for raising and lowering operation of high mast complete all as specified and directed.

Material and labour for earthing complete with galvanised earth plate electrode 600x600x6.0mm thick, buried directly in ground (Earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.50 mtr below normal ground level connected with galvanised iron earth strip 32x6mm by means of bolts, nuts, check nuts and washer of galvanised iron or steel complete with 40 mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15 type B1 in pit with angle iron (25x25x3)mm frame work with precast RCC 1:2:4 type B-1 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways and 12mm dia MS fabricated handle, test piont etc. in and including light frade GI protection pipe 40mm bore up to 7.5m lenght for drawing in earth lead wire , all as shown in electrical plate No.3 of SSR Part-1 complete with necessary earth work in any type of soil, removal to a distance not exc. 50m, testing on completion complete all as specified and directed. NOTE: (i) Earth lead strip and its protection pipe upto and including 7.5 mtr only from the top of earth electrode are included under this item. (ii) Any joints in earth lead from earth electrode to test point shall not be allowed/permitted. (iii) If the desired earth resistance is not found within permissible limit shall be re done by contractor at no extra cost.

Supply and fixing LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equiped with IP66 protection with impact and corrosion resistant complete with driver and lamp complete with all accessories and including connecting up with three core flexible copper conductor cable of suitable size etc complete all as specified and directed.

Supply, laying, connecting and testing UG XLPE insulated, screened, PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor rating 1100 volts grade of size 10 Sqmm 4 core laid in trenches or passing through pipes/ducts or fixed to walls/poles complete all as specified & directed. (Earth work, brick protection and sand cushioning shall be measured and paid for separately).

Excavation in trenches soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out for foundation, cable etc or for shaft, man holes etc not exc not 10 sqmm on plan, complete all as specified & directed.

Material and labour for sand cushioning and covering of UG cable using crushed metal sand in trenches for cable protection complete all as specified & directed. NOTE: - Punned thickness shall be measurement & paid

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm in soils, complete all as specified and directed.

Removing excavated material (soils) not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified & directed.

Material and labour for brick well burnt sub class ‘B’, old size as cover to U/G cable laid dry flat over the cable with width equal to length of the cable and abutting each other with gap between adjacent slab not exceeding 10mm over under ground cable for cable protection in trenches, all as specified and directed.

Material and labour point wiring with 3 runs of 2.5 Sqmm (colour code as per IE Rules) FRLS, PVC insulated, unsheathed, single core, 1100 Volts grade, multistranded copper conductor cable/Wire in and including suitable concealed PVC conduit and green wire connected to common earth dolly, and including 1.6mm thick cadmium plated sunk MS pressed steel terminal boxes with 3.0 mm thick hylum sheet cover fixed with brass screw complete with all accessories for one light point/Fan point controlled by one ,one way switch complete all as specified and directed.

Supply and fix MCB combo box modular type in sheet metal enclosure SPN socket complete with one SPN MCB 20 Amps, 240 volts including connection with suitable size copper lugs complete all as specified and directed..

Supply and fix Geyser vertical mount type 25 Ltrs capacity BEE five star rated , shockproof and rust proof metal body compact size including two nos PVC connection heavy duty and connecting with all fixing arrangement of nuts & bolts and fixing on wall etc including taking down old geyser and deposited to AGE EM-II store yard complete all as specified and directed.

Excavating in post holes (or similar holes) in hard/dense soil each n exc 0.5 cu. M, getting out, returning, filling in and raming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in any type of soil complete all as specified & directed.

Material and labour PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed.

Material and labour for mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165complete all as specified & directed.

Material and labour for applying two coat of synthetic enamel paint over one coat of red oxide primer including prepartion of new surfaces of any description not other wise described over 10 cm width or girth complete all as specified and directed.

Supply abnd fix pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Material and labour for brick work with sub class bricks old size, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and ditected.

Material and labour for with 15 mm thick rendering on of brick work or concrete surfaces in cement mortar 1:4 finished surfaces even and smooth with using extra cement, complete all as specified and as directed.

Material and labour TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Description all as per item no 56 above but 8 mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

Material and labour for use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, plinth beams and similar work; vertical or to batter complete all as specified and directed.

Material and labour for use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or slopingetc complete all as specified and directed

Material and labour for use and waste formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed .

Material and labour for reinforced cement concrete type B-1 1:2:4 ( using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beam,columns etc. complete all as specifed and directed.

Material and labour nominal mix 1:2:4, type B1 (using 20mm graded aggregate) for slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slab and in shelves and this like complete all as specified and directed.

Material and labour for 15 to 18 mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Supply and fix framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc.(Beam, tee, angle, channel ,hollow sections or flat sections) including distance pieces, cleats etc complete all as specified and directed.

Material and labour finishing walls with Acrylic Smooth exterior paint of required shade on new surfaces (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)etc including prepration of surfaces, complete all as specified and directed.

Supply and fix 3 mm thick ACP (Aluminium composite material) fixed with screw on existing mild steel frame complete all as specified and directed. Note:- Mild steel frame work shall be measured and paid seperately.

Supply and fix for stainless steel 304 grade pre fabricated letters of size 6" height in English or Hindi and fixed on position by means of brass screws etc complete all as specified and directed.

Material and labour for providing cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

Supply only Chain link MS galvanised fencing, any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire any size or type complete all as specified and directed.

Supply and fix mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 5cm but not exc 22.50 cm long, diameter of neck n exc 12 mm complete all as specified and directed.

Supply and fix Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75mm spacings and straining (as in linear) and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

Supply and fix concertina coil (reinforced punched barbed tape single layer) fixed on Y shape angle iron complete all as specified and as directed. (i) Dia of concertina coil 600 mm dia (ii) Nos of turns in concertina 50 to 53 turns (iii) Weight of each coil 9.5 to 10 Kg (iv) Coverage per coil 6 RM

Note :- Amount of credit of Rs. NIL for retrieved materials is mentioned in Schedule of Credit Page No 18 of tender documents in pdf form which will be deducted offline while acceptance of tender.

M/s Pradeep Kumar (BID ID -3300879)