Construction of HP.PWD Executive Engineer Residence at Bhawarna

Amount

Excavation in foundation, trenches etcetera in earth work involving all classification of soil such as pick work, pick jumper work, blasting work, soft or hard rocks including chiseling/wedging out of rocks where blasting work is prohibited or any other mixed variety of intermediate soil, dewatering and removal of slush if arrisen during course of construction and lifts upto all heights including stacking the excavated soil not more than three meters clear from the edge of the excavation and then returning the stacked soil in 15 cm (fifteen centimeters) thick layers when required into plinths, sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus excavation earth within all leads,lifts by any mode of transportation and other incidental, as per the direction and entire satisfaction of Engineer-In-Charge. Any loss to the private and public property during course of construction shall be absolute responsibility of the contractor. Rate inclusive royalty, malkana, toll tax, GST and other taxes imposed by the government.

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Any loss to the private and public property during course of construction shall be absolute responsibility of the contractor.Rate inclusive royalty, malkana, toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation,. Footings bases of columns and mass concrete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and the like floor etc. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surface such as walls up to any thickness / any height . The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders lintels, sides, and soffits of beams haunchings, cantilevers bressumers and lintels upto all depths in all floor. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillars , posts and struts, square, rectangular, polygonal in plain in all floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing in all floor. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls up to any width. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:6:12 (One cement isto six sand isto twelve aggregate) graded crushed stone aggregate 40mm (forty milimeter) nominal size mechanically mixed and curing complete, excluding cost of form work in foundation and plinth as per approved specification and drawing including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:5:10 (One cement isto five sand isto ten aggregate) graded crushed stone aggregate 40mm (forty milimeter) nominal size mechanically mixed and curing complete, excluding cost of form work in foundation and plinth as per approved specification and drawing including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:4:8 (One cement isto four sand isto eight aggregate) graded crushed stone aggregate 40mm (forty milimeter) nominal size mechanically mixed and curing complete, excluding cost of form work in foundation and plinth as per approved specification, drawing including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:3:6 ( one cement isto three sand isto six graded, crushed stone aggregate 40mm (forty millimetre) nominal size) mechanically mixed and curing complete excluding cost of form work in foundation and plinth including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying plain cement concrete work M20 (M twenty) with cement contents not less than 320 kg (three hundred and twenty kilogramme) per cubic metre mechanically mixed and vibrated and curing complete as per PWD specification, drawing excluding cost of form work in foundation and plinth including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work M-20 (M-twenty) design mix to obtain the minimum compresive strength 20N/mm2 (Twenty newton per square millimeter) and minimum cement content not less than 320 kg/cubic meter(Three hundred twenty Kilogramme per cubic metre) and curing complete and mechanically mixed and vibrated as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in suspended floor roofs, landing and shelves and their supports balconies, beams, girder, bressumers and cantiliver upto any floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength of 20N/mm2( twenty newton per square millimetre) and minimum cement content not less than 320 kg/cubic meter mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design excluding cost of form work and reinforcement for reinforced concrete work in coulmn, pillers posts and struts upto any floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work M-20(M-twenty) design mix to obtain the minimum compresive strength of 20N/mm2( twenty newton per square millimetre) and minimum cement content not less than 320 kg/cubic meter (Three hundred twenty kilogramme per cubic metre) mechanically mixed and vibrated including curing complete as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in stair cases (except spiral stair cases) excluding landings, but including preparing of top surfaces and finishing of nosing upto all floor levels. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying work M-20(M-twenty) design mix to obtain the minimum compresive strength of 20N/mm2( twenty newton per square millimetre) and minimum cement content not less than 320 kg/cubic meter (Three hundred twenty kilogramme per cubic metre) mechanically mixed and vibrated including curing complete as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in Walls any thickness but not less than 0.10 mm (thickness) I/c attached pillasters buttresses plinth and string course etc. from top of foundation upto floor two level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying Damp Proof Course 50 mm (Fifty millimetres) thick with cement concrete 1:2:4 (one cement isto two sand isto four graded crushed stone aggregate 20 mm (Twenty millimetres nominal size) mechanically mix including cost of form work and curing complete, as required at site as per H.P.P.W.D. specification, approved drawing design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rates including octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government.

Applying a coat of hot bitumen (mexphalt) 80/100 (Eighty by hundred) or equivalent using 1.70 kg (one decimal seven) kilogram per square meter on damp proof course after cleaning the surface with a piece of cloth lightly socked with kerosene as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge.

Providing and laying tor steel of TISCO, SAIL reinforcement for reinforced cement concrete work including bending, binding and placing in position complete in all respects as per approved drawing, design, and specification in all floor levels including the cost of binding wire and cost of dewatering if arrisen during placement of reinforcement as per PWD specification and approved, drawing design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Second class brick work using common burnt clay building bricks in cement mortar 1:6 (one cement isto six sand) in super structure upto all floor lavels as per PWD specification drawing and design and curing complete including scaffolding. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Second class half brick work using common burnt clay building bricks with hoop iron in cement mortar 1:4 (one cement isto four sand) in super structure as per PWD specification, drawing and design and curing complete including scaffolding. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 12mm (Twelve millimetre) thick Prelaminated board both side particular board of action tesa / kitdam/ kitply/ green ply as per ISI and approved shade for infill panels of aluminium door as per PWD specification, drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 40 mm thick (Fourty millimetre) First class teak wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G (Eighty five guage) with wire of dia 0.56 mm (zero decimal five six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws. The rate is inclusive of octroi, royality, malkana, sales tax, toll tax, GST or all type of other taxes imposed by the Government.

Providing and fixing 19mm (Nineteen millimetre) thick water proof termit resistante commercial board of Centuary/ kit ply/ Dura ply/ Marino (ISI marked) for cup board with hard wood edging and to be finished with mica laminatory of approved shades complete including bright finished black enamelled iron butt hinges with screws etcetera complete as per H.P.P.W.D. specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidential as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 19mm (Nineteen millimetre) thick water proof termit resistante commercial board of Centuary/ kit ply/ Dura ply/ Marino (ISI marked) shelves/ box for cup board with hard wood edging and to be finished with mica laminatory of approved shades complete as per H.P.P.W.D. specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidential as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 6mm (Six milimetre) thick ply wood linning with butt jointing and nails (Frame work and cover fillets to be measured and paid for separately) complete including carriage of material within all leads, lifts and other incidential as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 8mm (Eight milimetre) thick partical cement bounded board ceiling of approved quality with butt jointing and nail(frame work and cover fillets to be paid for separately. Particle Board (bwp phenol bonded exterior / interior graded) complete including carriage of material within all leads, lifts and other incidential as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 12mm (Twelve millimetre) thick and 150 mm (one Hundred fifty millimetre) wide palmet with 25mm (Twenty five millimetre) diameter wooden curtain rod and brackets including fixing with 25x3mm (Twenty five into three millimetre) M.S. flat 10 cm (Ten centimetre) long and plugs etc. complete.1st class deodar wood complete including carriage of material within all leads, lifts and other incidential as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing Mild Steel grills 10mm x10mm (Ten millimetre into ten millimetre) square bars in combination of 20x4mm (Twenty into four millimetre) Mild Steel flat of required patterns in frames of windows etcetera with round headed bolts and nuts or by screws complete as per H.P.P.W.D. specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads lifts and other incidential. The rate is inclusive of octroi, royality, malkana, sales tax, toll tax, GST or all type of other taxes imposed by the Government.

Providing and fixing coloured / anodized aluminum sliding door bolt, anodized transparent or dyed to required colour and shade with bolts and nuts, screws etcetra complete. 300x16mm (Three hundred into sixteen millimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing coloured anodized aluminum tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetra complete 300x10mm (Three hundred into ten milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing coloured anodized aluminum tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetra complete.250x10mm (Two hundred fifty into ten milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing coloured / anodized aluminum handle anodized transparent or dyed to required shade or colour with necessary screws etcetera complete.125mm (one hundred twenty five milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing coloured anodized aluminum handle anodized transparent or dyed to required shade or colour with necessary screws etcetera complete.100mm (one hundred milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing oxidized aluminium single acting spring hinges with necessary screws etc. complete.150 mm (one hundred fifty milimeter) size.The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing oxidized aluminium hooks and eyes 150 mm (one hundred fifty milimeter) size.The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying 600x600mm( six hundred into six hundred millimeter) acid resistance vetrified tiles of Restile/ Nitco/ Rak/ Simpolo/ Kajaria/ Johnson as per approved shade and design as per drawing and specification in flooring, skirting and dado laid over 12 mm ( twelve millimeters) thick cement mortar 1:3 (one cement: three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as reuired complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying 300x300x10 mm ( three hundred into three hundred into ten millimeters) thick antiskid ceramic tiles of premum quality of Nitco/ Kajaria/ Somany/ Well/ Johnson as per approved shade and manufacture in flooring over 12 mm ( twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete as per approved specification, drawing and design including entire . The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying chima pink granite stone with rough finish single slab (80% polished and 20% un polished of approved shade with 5 cm ( five centimeters) wide flaming bond near nosing for stair treads, with polished granite ( black) single slab for riser of steps having semi round nosing 20 mm ( twenty millimeters)thickness base of cement mortor 1:3( one cement: three sand ) laid over and jointed with cement slurry mixed with pigment to match the shade of granite stone. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing 40mm (Forty millimetre) thick Cement concrete flooring 1:2:4 (one cement isto two snad isto four aggregate) graded/crushed stone aggregate 20 mm (tewenty milimeter) nominal size mechanically mixed including curing complete as per PWD specification, laid in one layer finished with a floating coat of neat cement. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

15mm (fifteen milimeters) thick cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimetewrs) in girth, in rough side with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

15mm (fifteen milimeter) thick cement plaster in fair coat on the fair side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimeters) in girth, in rough side with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

6mm (six millimeter) cement plaster 1:3 (one cement isto three sand) in ceiling complete including curing complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

15mm (fifteen milimeters) thick cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimetre) in girth, in rough side with cement mortar 1:3 (one cement isto three sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying granite stone in flooring 20mm (Twenty millimetre) average thickness base of cement mortar 1:3 (One cement isto three sand) laid over and jointed withgrey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing andpolishing complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 0.60mm (sixty millimetre) thick prepainted steel sheet (IS marked Z-120) over steel trussed in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating Tata/ Sail/ Reliance/ Jinda including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (six millimetre) diametres with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-In-charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing pre-painted steel sheet ridge or hips 60cm (sixty centimetre) over all with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheets with top coat of regulat modified polyster organic coating of 20 (twenty) microns over 5 (Five) microns primer coating + back coating of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetre) dia prepainted bitumen washers complete in all respect as per approved drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing pre-painted sheet valleys 90cm (Ninety centimetre) over all with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regulat modified polyster organic coating of 20 (twenty) mocrons over 5 (Five) microns coating + back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with J or L hooks, bolts and nuts 6mm (Six millimetre) dia with prepainted limpet and bitumen washers complete in all respect as per approved drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15cm (Fifteen centimetre) wide 45cm (forty five centimeter) deep over all semicircular plain G.I. sheet gutter with iron brackets 40x3mm (Fourty into three millimetre) size bolts and nuts and washers etc. including making necessary connections with rain water pipe complete as per design 0.63mm ( zero point sixty three millimeters) thick sheet.The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing plain B.P. sheet 2 mm (two millimetre) thick fixed in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per PWD specification (Base members of steel work shall be measured & paid separtely). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing on wall face PVC (D-plast) rain water pipes of working pressure not less than 4.00/6.00 kg (four to six kilogram) per centimetre square including filling the joints with approved adhesive complete 110 mm (one hundred ten milimeter) dia as per ISI marked pipe. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing on wall face PVC (D-plast) accessories for rain water pipes including filling the joints with approved adhesive complete 110 mm (one hundred ten milimeter) dia PVC plain bend as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer- In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing on wall face PVC (D-plast) accessories for rain water pipes including filling the joints with approved adhesive complete 110 mm (one hundred ten milimeter) dia PVC plain shoes as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer- in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing for PVC pipe steel Clamps ISI Marked of approved design with steel screws and rawal plug etc. complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing First class Teak wood work in frames of doors , windows , clearstory, windows and other frames wrought , framed and fixed in position complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 40mm (Forty millimetre) thick First class teak wood panelled glazed or panelled and glazed shutters for doors windows and clerestory windows including black enamelled in but hinges with necessary screws complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Steel work welded in built up sections of Tata/Sail/Jindal composed in beams, joists, channels, angles, tees flats with connecting plates or angles, cleats as in trusses and trussed purlins, main and cross beams, hips, jack rafters, purlins connect to common rafter and like work including cutting hoisting fixing in position & applying a priming coat of red lead paint complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S.fan clamp type -1 of 16 mm (sixteen millimetre) dia M.S. bar bent to shape with hooked ends in R.C.C slab during laying including painting the exposed portion of loop,all as per standard design complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Painting two coats(excluding priming costs) on new steel and other metal surfaces with enamel paint to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Applying a priming coat over new wood and wood bases surfaces after and including preparing the surface by thoroughly cleaning, oil, grease, dirt and other foreign matter, sand papering and knotting with ready mixed paints brushing wood primer pink as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint brushing to give an any shade including cleaning the surfaces of all dirt, dust and other foreign matters sand papering and stopping as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Wall painting (two coats) with acrylic emulsion washable paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface.The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Finishing wall with spectrum textured wall finish natural grit of heritage coating of 1.5 mm (One decimal five millimetre) thickness water proofing cement paint of approved shade and manufacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after throughly brushing the surface to remove all dirt and remains of loose powedred material.The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing under layer for plinth protection of 75 mm (Seventy five millimetre) thick unconsolidated) bed of dry brick stone broken aggregate 40mm (Forty millimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing plinth protection 50mm (Fifty millimetre) thick with cement concrete 1:3:6 (One cement isto Three sand: Six graded stone aggregate 20mm (Twenty milimetre)nominal size including finishing the top surface of concrete smooth per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government..

Construction of cement concrete covered drain in cement concrete 1:3:6 (One cement isto Three Sand isto Six graded stone aggregate 20mm (Twenty milimetre) nominal size_ including earth work shuttering and cast in-situ RCC slab over drain and cement concrete flooring 1:2:4 (One cement isto Two sand isto Four graded stone aggregate) and finished with a floating ncoat of neat cement complete as per standard design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government..

Providing and fixing stainless steel 85 cm ( Eighty five centimeters) high know down stair railing of kitch 38 mm (thirty eight millimeters) dia hand rail fixed on 10x50 mm ( ten into fifty millimeters) side mounted flat blauster system with glass no DS 54-2- G-10 placed at 1200 mm ( twelve hundred millimeters) center to center along with 3 Nos( three numbers) 10mm ( ten millimeters) mid rail connected at side of blauster with fixes on the blauster would be fixed on floor with casted base plate on minimum 6 mm ( six millimeters) thickness base plate shall be conncected with suitable SS grade over cape alinging complete as per detail and design.The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing SST railing 50 mm ( fifty millimeters) dia hand rail slip resistance with rounded ends at two level at 75 cm to 90 cm ( Seventy five centimeter to ninety centimeter) high and extended and 30 cm ( thirty centimeter) beyond top and botton of ramp as per detail and 25 mm ( twenty five millimeters) dia SST bullasters welded to 50 mm ( fifty millimeters) dia SST pipe embended and cement concrete 600 mm ( six hundred millimeters) center to center as per detail and specification.The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying brick bat filling aggregate under soak pit including entire carriage of materials as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in cement mortar 1:5 (one cement isto five sand) including curing complete as per approved specification, drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fittings and clamps including making good the wall, ceiling and floor. The rates are including cost and carriage within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

15 mm ( Fifteen millimetre) nominal bore

20 mm ( Twenty millimetre) nominal bore

Providing and fixing PVC Floor Trap size 110x75 mm ( one hundred ten into seventy five millimeters) ISI marked self cleaning design including fixing with approved adhesive cost of cutting and making good the wall and floor complete.within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing PVC pipes (working pressure not less than 4.50kg/sqm(four decimal five zero kilogramme per square metre) including filling the joints with approved adhesive complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer- In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

150 mm (One hundred fifty millimetre) dia

110 mm (One hundred ten millimetre) dia

75 mm ( Seventy five millimetre) dia

Providing and fixing PVC Single Equal Branch with plain access ISI Marked insertion rubber washer 3 mm thick bolt and nuts complete including fixing with approved adhesive etc. Complete. within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre) diametre.

75 mm (Seventy five millimetre) diametre.

Providing and fixing PVC Single Equal Branch with oval access door ISI Marked insertion rubber washer 3 mm thick bolt and nuts complete including fixing with approved adhesive etc. complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre) diametre.

75 mm (Seventy five millimetre) diametre.

Providing and fixing PVC Plain Bend ISI Marked including fixing with approved adhesive etc. complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre) diametre.

75 mm ( Seventy five millimetre) diametre.

Providing and fixing PVC door bend with ovel access door, insertion rubber washer 3mm (three millimetre) thick bolts and nuts ISI marked complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

110mm (one hundred ten millimetre) diametre.

75mm (seventy five millimetre) diametre.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etcetera including carriage of materials within all leads and lifts complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

110mm (one hundred ten millimetre) diametre.

75mm (seventy five millimetre) diametre.

Providing and fixing steel Clamps ISI Marked of approved design with steel screws and rawal plug etc. Complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre)

75 mm ( Seventy five millimetre)

Providing and fixing flat back 550x400mm (five hundred fifty into four hundred millimetre) vitreous china wash basin with single hole for pillar tap with CI or MS brackets painted white including cutting holes and making good the same but excluding fittings including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 32mm (Thirty two millimetre) diameters C.P. brass waste (Heavy duty make ISI marked NO-8931 & 8934) for wash basin or sink with in all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 600mmx450mm (six hundred millimeter into four hundred fifty millimeter) beveled edge mirror of superior glass mounted on 6mm (six millimeter) thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. screws and washers of Atul/Modi Guard/ Golden fish including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 600x120mm (Six hundred into one hundred twenty milimetres) glass shelf with C.P. brass brackets and guard rail complete fixed to wooden plugs with C.P. brass screws, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. (Charomium plated) brass Toilet paper holder, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing chromium plated brass soap dish of ESS with C.P. brass brackets fixed with cleats with C.P. brass screws, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm (fifteen millimetre) diametre C.P.brass bib tap heavy duty with capstan head including carriage of materials within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm (fifteen milimetre) C.P. Brass Angle valve without nuts & bolts including carriage of materials within all leads, lifts, and other incidentals. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. brass pillar tap Continental/Classic sreies /florol series of Jaguare/Hindware/Cera 15mm (fifteen millimetre) dia (Heavey duty makes ISI marked No. 8931 & 8934) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 450 mm X 350 mm X 150 mm (Four hundred fifty into three hundred fifty into one hundred fifty milimetre) Vitreous China laboratory sink with C.I. or M.S. brackets painted white including cutting holes in walls and making good the same but excluding fittings complete in all respect including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing PVC connection 15 mm( fifteen millimeters)nominal bore and 450 mm ( four hundred millimeters) long including necessary fitting complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. brass full way valve with wheel of continental series/ clasic series/ floral series of Hindware/Jaguar/Cera within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 100mm (One hundred milimetre) nominal size diameters CP grating of ESS or nahani trap of approved brand complete, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing PTMT/PVC jet sprey of continental series/clasic series/floral series of jaguar/ hindware/ cera for Europen seat of approved brand and manufacture, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and placing water tank of make PVC (Poly venyl chloride) Sintex having capacity 1000 ( One thousand hundred ) litres each with necessary fitting including over flow pipes scour pipe and bull valve and with cover locking arrangement of good quality including providing pads of sizes as required for inlet and outlet and inside painting of good quality all complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Construction manhole with R.C.C. top slab in 1:2:4 (One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size), foundation concrete 1:4:8 (One cement: Four sand: Eight graded crushed stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm (Fifteen milimetres) thick with cement mortar 1:3 (One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetres) 500mm(Five hundred milimetres) deep, including Precast cement concrete cover (medium duty) with 300mm (Three hundred milimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Construction manhole with R.C.C. top slab in 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size), foundation concrete 1:4:8 (One cement: Four sand: Eight graded crushed stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm (Fifteen milimetres) thick with cement mortar 1:3 (One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetres) 500mm(Five hundred milimetres) deep, including P.C.C (Precast Cement Concrete) cover with frame (Medium duty single seal pattern–I) with 200mm (Two hundred milimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Constructing brick masonry chamber for under ground CI inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (one cement : five sand) cover with frame (light duty) 355mmx6mm internal dimensions total weight of cover with frame to be not less then 38Kg. (weight of cover 23Kg. and weight of frame 15Kg) RCC top slab with 1:2:4 (one cement : two sand : four graded stone aggregate 20mm nominal size) foundation concrete 1:5:10 (one cement : five sand : ten graded stone aggregate 40mm nominal size) in side plaster 15mm thick with cement mortar 1:3 (one cement : three sand) finished smooth with floating coat of neat cement on wall and bed concrete etc. complete. Inside dimension 455x610x450mm deep single pipe line. The rates are including cost and carriage within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:4:8 (one cement isto four sand isto eight graded stone aggregate 40 mm (Forty millimetre) nominal size bedding for PVC pipes of the 150 mm (One hundred fifty millimetre) internal diameters, necessary form work and curing complete. The rates are including cost and carriage within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Making connection of galvanised mild steel distribution branch with galvanised mild steel main 20mm (Twenty millimetre) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying mechanically mixed and vibrated cement concrete 1:2:4 ( one cement : two sand : four graded, crushed stone aggregate 20mm (twenty millimetre) nominal size) and curing complete excluding cost of form work in foundation and plinth as per approved specification, drawing including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

10mm (ten millimetre) thick cement plaster in single coat on fair side of brick/concrete walls for internal plastering upot all floor level including arrises, internal rounded angles chamfers and/or rounded angle not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:3 (one cement : three sand) The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing precast reinforced cement concrete slab upto any thickness and width in 1:2:4 (one cement : two sand : four graded,crushed stone aggregate 10mm (ten millimetre) nominal size) upto all floor level including centring and form work and curing complete, but excluding cost of reinforcement and including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing precast reinforced cement concrete eaves board/slab average thickness 25mm (twenty five millimetre) and 15cm to 30cm (fifteen centimetre to thirty centimetre) wide in 1:2:4 (one cement : two sand : four graded, crushed stone aggregate 10mm (ten millimetre) nominal size) upto floor all level including centring and form work and curing complete but excluding cost of reinforcement and including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Steel work welded in built up sections trusses and framed work including cutting, hoisting, fixing and launching in position and applying a priming coat of red lead paint in gratings framed guard bars ladders, railings, brackets and similar works including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Constructing water collection chamber 300x300x500mm (three hundred into three hundred into five hundred millimetre) in side size for collection of water with cement concrete slab 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimeetre) nominal size) 75mm (seventy five millimetre) thick foundation concrete 1:5:10 (one cement : five sand : ten graded, crushed stone aggregate 40mm (forty millimetre) nominal size) finished with floating coat of neat cement and 100mm (one hundred millimetre) cast insitu plain concrete wall in 1:2:4 (one cement : two sand : four graded,crushed stone aggregate 20mm (twenty millimetre nominal size) including form work complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints with cement mortar 1:5 (One cement Five sand) including carriage of materials within all leads and lifts of materials and other incidentals complete in all respect as per direction and satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Supplying and laying of brick aggregate 50mm (fifty millimetre) nominal size including carriage of materials within all leads and lifts complete complete in all respect as per direction and satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

M/S KEWAL KRISHAN