ADDN/ALTN TO BLDG NO. P-33 (SPORTS COMPLEX) AND PROVISION OF ADDL SECURITY LIGHTS AT AF STN HIGHGROUNDS

Amount

BUILDING WORK

Excavation in trenches in soft/loose soil not excedding 1.5 metre wide and not exceeding 1.5 metre deep for laying/taking out cables and foundation of poles etc and getting out complete all as specified and as directed.

Returning, filling in trenches (soil), including spreading, leveling and well ramming in layers not exceeding 25cm thick complete all as specified and as directed.

Removal of surplus excavated soil to a distance not exceeding 50metre and depositing where directed at a level not exceeding 1.5metre above the starting point, complete all as specified and as directed.

M&L for 75mm thick plain cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) as in subbase, finishing the top surface even and rough to receive the top layer complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc, laid beded and pointed in any mortar complete all as specified and as directed.

Dismantling floor, hearth or wall tiling, terrazzo toping/dado etc including cement mortar bedding/backing and removing rubbish off the premises out of MoD land, including preparation of dismantled surface to receive the backing coat/bedding layer for tiles, complete all as specified and as directed.

M&L for providing and laying factory made cement concrete paver block, M-35 grade, chamfered edge with approved colour, design, colour and pattern confirming to IS-15658-2006 of 60mm thick made by table vibratory method using PU mould, laid in required colour pattern as in footpath, parks/lawn drive ways or light traffic parking etc; over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand etc complete all as specified and as directed.

M&L for providing and laying factory made cement concrete Kerb stone of M-25, at or near ground level in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and as directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.60 mm thick of colour as approved by the AGE(I) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.60mm thick of colour as approved by the AGE(I) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F tie bars (sag rods) with screwed ends, nut washers and mild steel plates for roofs, arches etc king rods and straining bolts confirming to FE 290 Gde-E-165 complete all as specified and as directed.

M&L for Drilling holes exc 12 mm dia and n.exc 25 mm mm (and countersunk if required) of depth of hole exc 3 mm but n.exc 12 mm complete all as specified and as directed.

M&L for preparation new steel surfaces n. exc 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation old painted steel surfaces exc 10cm in width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

Dismantling boarding (un- framed), any description and in any position fixed with nails complete all as specified and as directed.

S&F 20 mm thick second class hard wood boarding as in Eaves boards, one side plained with butt joints fixed with nails complete all as specified and as directed.

M&L for Preparation of new wooden surfaces exc 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins arches pillars etc complete all as specified and as directed.

M&L for brick work sub class “B” bricks straight or curveted in plan exc. 6mtr mean radius with old size bricks built in CM 1:6 complete all as specified and as directed.

M&L for Mild steed TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Mild Steel TMT bars 5 mm dia and over upto and including 10mm dia as in stirrups, spacers and binders etc cut to length, bent to shape required, including cranking, bending etc., and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for Reinforced cement concrete 1:1.5:3, Type A-1 (nominal mix) using 20mm graded crushed stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for Reinforced cement concrete 1:1.5:3, Type A-1 (nominal mix) using 20mm graded crushed stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for Formwork to sides of foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rough finshed surface of concrete complete all as specified and as directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions, rough finshed surface of concrete complete all as specified and as directed.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:6 as on brick walls finished the surface even & smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:4 as on brick walls finished the surface even & fair without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls by rubbing down, washing & stopping of distempered surfaces and applying two coats of water based distemper (Ist quality) over a coat of chalk whiting complete all as specified and as directed.

M&L for preparation of old decorated plastered surfaces of walls by rubbing down, washing & stopping of distempered surfaces and applying two coats of water based distemper (Ist quality) complete all as specified and as directed.

Complete removal of existing treatment on old wall surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed.

M&L for Preparation of new plastered/unplastered wall surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed.

Demolition of cement concrete as in ground floors and in paving not exc 15cm thick below or above ground level complete all as specified and as directed.

M&L for machine cut Kota stone slab flooring 18-20mm thick over and including 15mm thick screed in cm (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for Kota Stone Slab 18-20 mm thick as in riser of steps, skirting, dado and pillar etc laid over and including 10mm thick screed in cm (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for non skid coloured ceramic jointless tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick srceed bed in CM 1:6 complete all as specified and as directed.

All as per item No 39 here-in-before but as in skirting and dado over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for machine pressed Cement concrete chequered tiles with grey cement and pigment of size 25cm x 25cm x 22mm thick as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick srceed bed in CM 1:6 complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc )or insulation boards/slabs/blanket, any thickness, including cover fillets etc complete all as specified and as directed.

M&L for False ceiling board at all heights of 600 mmx600 mm x16 mm mineral fibre ceiling tiles of fine texture laid on and including grid system of size 24 mm x 32 mm made of hot dipped galvanised steel section . The exposed surface of grid chemically cleaned pre-painted /backed in polyster paint. The runners of standard length 3600 mm used alongwith cross section of 1200 mm c/c. Wall angle (size 22 mm x 22 mm ) of the same quality as the grid shall be used on periphery along the wall or partition using screws at 600 mm centre to centre and cross tee ( 24mm x 23 mm) to be interlocked between main runner at 600 mm c/c ( max) to form grid of 600mm x 600mm. The main runner shall be hanged from the soffit with the help of 4 mm GI wire hanger and 6 mm dia wire anchor fastener at 1200 mm c/c (max) complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area not exc. 1.5sqm each complete all as specified and as directed.

All as per item No 44 here-in-before but area exc.1.50sqm & not exc 4.00 sqm each

S&F Factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay with glazing bars, dovetailed or welded etc with and including one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEAF/STD-185-2012 Sheets 1/2 & 2/2.

S&F Factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay without glazing bars, dovetailed or welded etc with and including one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEAF/STD-185-2012 Sheets 1/2 & 2/2.

S&F steel window or ventilator, fixed type, with glazing bars with and including one shop coat of zinc chromate primer complete all as specified and as directed.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staple complete all as specified and as directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty or fixed with wooden beads having area not exc 0.50sqm in each pane complete all as specified and as directed.

M&L for preparing of new steel surfaces of any description, not otherwise described, over 10 cm with or girth & applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

All as per item No 52 here-in-before but except primer complete all as specified and as directed.

S&F Power coated aluminium (minium thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

S&F Power coated aluminium (minium thickness of powder coating 50 micron) door shutters, aluminium section weighing 0.55 kg/Rm with and including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

S&F plain sheet glass, ordinary quality 4.8mm thick in panels of aluminium doors/windows/partitions fixed with aluminium glazing clips & rubber beading complete all as specified and as directed.

S&F in repairs Door closer hydraulically regulated, designation No. 2, universal type, aluminium body (Die Cast) suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and as directed.

S&F Prelaminated particle board 12mm thick, exterior grade, prelaminated both side with decorative choice lamination fixed with with aluminium snap beading and rubber gasket packing both side of board complete all as specified and as directed.

M&L for 75 mm thick cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection and making 6 mm wide joints in every 2.5 m interval, at every corner and at junction with wall and plinth, joints shall be sealed with joint sealing comound grade 'A' complete all as specified and as directed.

S&F Pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and as directed.

S&F 35mm thick 2nd class hard wood plane framed panneled shutter (two panel) with pannels of 9mm BWP/12mm veneered particle board with commercial veneered on both faces. The size of rail and style as per IS 1003 (Part-1) Kiln seasoned and chemically pressure treated complete all as specified and as directed.

M&L for PCC 1:3:6 type C-0 using 12.5 mm graded crushed stone aggregate as in filling back of chowkhats complete all as specified and as directed .

S&F 300 mm long Aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F 125 mm size, aluminium anodized handles, cast type complete all as specified and as directed.

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

INTERNAL ELECTRIFICATION

Taking down copper/aluminum point wiring (light, fan, socket or power) complete including u/s fittings such as switches, ceiling rose, holders, sockets etc. and making good disturbed surfaces on walls/floors etc complete all as specified and as directed.

M&L for point wiring complete with 1.5 sqmm single core PVC insulated unsheathed FRLSH cable 1100 volts grade ISI marked with multi stranded copper conductor drawn through in and including conduit accessories ISI marked concealed in wall/fixed to roof ceiling etc and including provision of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FRLSH ISI marked as earth continuity conductor, fabrciated sunken terminal box made out of 1.22 mm thick sheet steel duly painted concealed in walls, with 3 mm thick bakelite sheet ISI marked top cover with brass/chromium plated screws and cup washers for housing switches, socket outlets, fan, regulators etc, complete all as specified and as directed. Note :- (i) The chases in the wall shall be cut with elect cutter (ii) The disturbed surfaces of wall shall be made good with cement plaster 1: 4 including matching the surfaces with two coats of white wash/colour wash/distemper all as per existing finishes and to the entire satisfaction of Engr-in-Charge.

All as per item No. 68 here-in-before but point wiring for one 5Amps socket outlet point on independent board controlled by one single pole, one way switch complete all as specified and as directed.

All as per item No. 68 here-in-before but point wiring for one 5Amps socket outlet point on the same board controlled by one single pole, one way switch complete all as specified and as directed.

All as per item No.68 here-in-before but point wiring using 2.5 sqmm as main wire & 2.5Sqmm as continuity earth wire, for one 15Amps socket outlet point on independent board controlled by one single pole, one way switch complete all as specified and as directed.

S&F Switch piano, flush type single pole, one way, 6 Amp 230volts complete all as specified and as directed.

S&F Switch piano, flush type, single pole, one way, 16 Amp 230volts complete all as specified and as directed.

S&F Socket outlet 2/3 pin combined, 6 Amp complete all as specified and as directed.

S&F Socket outlet 2/3 pin combined, 6/16 Amp complete all as specified and as directed.

S&F Ceiling rose, two to three terminals, PVC/ insulated body complete all as specified and as directed.

S&F fan regulator stepped electronic type 120W including provision of PVC flexible cable of size 1sqmm copper conductor as required complete all as specified and as directed.

S&F LED Decorative box type fitting 1x20W, prewired suitable for retrofit LED tubes, prewired upto connection block and connecting with three core PVC copper flexible cable of size 1. Sq. mm from ceiling rose to connector block, complete all as specified and as directed.

S&F LED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F exhaust fan, steel body AC single Phase. 230V of size 380mm sweep with, blades, frame and louvers including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F die cast aluminium housing with opal diffuser and built in cone LED bollard lighting 8 watt IP 65 cone series complete all as specifed and as directed.

S&F Sheet metal distribution board SPN, with double door, 4 ways, 415 volt with 200 Amps rated bus bar & IP 54 protection, including taking out old unserviceable complete all as specified and as directed.

S&F Sheet metal distribution board SPN, with double door, 8 ways, 415 volt with 200 Amps rated bus bar & IP 54 protection, including taking out old unserviceable complete all as specified and as directed.

S&F MCB 32/40 Amp, 415 Volt, TPN, breaking capacity 10 KA, 'C' curve, fixed in repairs complete all as specified and as directed.

S&F MCB 32/40 Amp, 415 Volt, SPN, breaking capacity 10 KA, 'C' curve, fixed in repairs complete all as specified and as directed.

S&F MCB 6 to 32 Amp, 240 Volt, SP, breaking capacity 10 KA, 'B' curve, fixed in repairs complete all as specified and as directed.

M& L for Sub main wiring with two single core 2.5 sqmm (nominal area) stranded copper conductor FRLSH PVC insulated and unsheathed cable drawn in and including non metalic PVC regid conduit medium grade of suitable size with all standard fittings, concealed, including one run of continuous PVC insulated stranded copper conductor FRLSH cable 2.5 sqmm (nominal area) for earth continuty, including taking out and removal of old sub main wiring complete all as specified and as directed. Note :- 2 runs of 2.5sqmm copper conductor phase and neutral and one run of same size earth wire including one run of PVC conduct with cutting, chasing & making good shall be measured as one unit length.

S&F 20mm dia rigid non-metallic PVC conduit exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and as directed.

S&F 1100 Volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm dia Galvanised iron suspension wire, Twin core 6 sqmm flat/circular cable complete all as specified and as directed.

S&F 1100 Volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm dia Galvanised iron suspension wire, Twin core 4 sqmm flat/circular cable complete all as specified and as directed.

S&F LED Street light fittings 35 watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant, thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F Steel tubular swaged poles complete with cast iron base plate, final taper plug, bolts, nuts and screws as specified, type 410 SP-22 (8.5 metres long) complete all as specified and as directed.

M&L for plain cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete etc complete all as specified and as directed.

M&L for plain cement concreat 1:2:4, type B1 as coping to elect poles etc with and including necessary form work complete all as specified and directed.

S&F 200x160x98mm PVC junction box having IP 65 protection with metric knockouts for 10sqmm cable entry with terminals/bus bar 4 pole including provision of one MCB 6 amps complete all as specified and as directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated and armoured, heavy duty, electric power cable, cross sectional area 6 Sqmm 2 core aluminum conductor 1100volts grade under ground cable including both side connection with cable lugs etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: Returning filling & removal of earth, sand cushioning and bricks for protection of cable shall be measured and paid separately.

M&L for sand cushioning with a layer of dry river sand and punning to provide required cover as per SSR part -I complete all as specified and as directed. Note : Punned down thickness (overall 18cm) shall be considered for measurement and payment.

M&L for locally available, sub class 'B' bricks (old size), laid flat and dry perpendicular to the direction of cable adjacent to each other, in trenches over the cable for protection, complete all as specified and as directed.

M&L for earthing complete with GI earth plate electrode of size 600mm x 600mm x 6mm thick burried directly in ground vertically (depth of pit not less than 2.25 m below normal ground level), with top edge of earth plate not less than 1.5 m below normal ground level, earth plate surrounded from all sides by 15cm thick packed alternate layers of charcoal dust and common salt, electrode connections using galvanized lead wire 4mm dia (upto body of equipment) by means of nuts, bolts, check nuts & GI washers, connected to main switch board or main control board or test point, protected by galvanized iron pipe light grade 15mm dia bore, and watering pipe 20 mm bore GI light grade pipe with funnel & wire mesh, including all necessary excavation & earth work, PCC chamber in PCC (1:2:4) type B-1 & RCC cover, all as shown in electrical plate No 3 of MES Schedule Part-I (2009), testing on completion, including taking out old earthing materials and removal complete all as specified and directed. Note(s) :- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include GI lead wire and protection pipe of length 7.5m, GI pipe beyond 7.5m length required at site shall be measured and paid separately. (iv) Earth resistance should be less than 3 Ohm. In case the test results are not found below 3 Ohm, complete earthing will be redone without any extra cost to Govt.

Note: The Total amount shall subject to adjustment of credit of Rs 37189.00 for old Materials as per Schedule of Credit.

B N FRIENDS AND CO