PROVN OF TOILET IN BLDG No P 35 OF REGIONAL CENTER ECHS, PROVN OF 01 X GENERATOR SHED AND PAVED BLOCK FLOORING NEAR BLDG NO P-350H FOR 260 FD WKSH COY EME AND PROVN OF WALL PARTITION WITH DOOR IN OT II OF MH TRIVANDRUM AT PANGODE MIL STN TVM

Amount

M&L for demolition of brick work/stone masonry built in cement mortar and removing the debris/rubbish to a distance n.exc 100m as directed by Engineer-in-Charge.

M&L for demolition of stone slabs and tiles of any description or thickness in floor laid bedded and pointed in any mortar all as specified and directed.

Excavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation etc or for walls, shafts, manholes not exc 10 Sqm on plan or for laying pipes/cables etc and getting out, in soft/loose soil complete all as directed.

Surface excavation not exc 30 cm deep and averaging 15cm deep & getting out in soft/loose soil complete all as specified and directed.

Excavation in Post holes ( or similar holes ) in hard dense soil, each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm all as specified and directed..

M&L for Plain cement concrete 1:4:8 Type D-2, using 40 mm graded stone aggregate as in foundation all as specified and directed.

M&L Providing cement concrete 1:3:6 type C2 (40 mm graded stone agg) as in foundations, filling and mass concrete all as specified and directed.

Material and labour for cement concrete PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in sub base 100mm thick finished even and fair complete all as specified and directed.

Sand filling/cushioning under floors or in foundations including watering and consolidation all as specified and directed.

M&L for machine pressed precast concrete interlocking coloured paver block any shape and size confirming to IS 15658-2006 of 60mm thickness , M-35 Grade with grey cenent and pigment.

M&L for PCC type B1 1:2:4 using 20 mm graded stone aggregate in kerbs or mud stops rounded or chamfered edges etc complete all as specified and directed..

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as directed.

Removing excavated materials to a distance not exc 50m and depositing where directed at a level not exc 1.5 m above the starting point in soils complete all as directed.

S&F powder coated aluminum partition/doors section including necessary joining cleats,glazing clips, rubber neoprene packing for fixing particle board/glass etc powder coating of any colour (thickness of powder coating minimum 50 micron ) all as specified and directed.

Material and labour for 18mm thick prelaminated particle board grade 2 quality interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination type including 6mm thick teak wood leeping fixed with screws to timber framed work in repair with necessary fitting complete all as specified and directed.

Supply and fix in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brass bracket guard and railing 60cm long, complete all as directed.

S&F Door closer hydralulically regulated designation No 3 universal type, suitable for door shutters of 851 to 1000 mm width and weight between 61 to 80 Kg and fixed using aluminium extruded section all as specified and directed by Engr-in-charge.

Supply and fix butt hinges, medium weight cold rolled mild steel 100 mm size welded to angle iron frames or fixed with screws to wooden frames complete all as specified and directed.

Supply and fix 200 mm long anodized aluminum barrel tower bolt, extruded section complete all as specified and directed.

Supply and fix aluminium alloy handles extruded, fabricated type, anodised of 150mm size complete all as specified and directed.

S&F Brass Mortice lock of 4 Levers, vertical type, of size 100mm all as specified and directed.

Supply and fix floor door stopper of brass body length of pipe 150mm and tongue anodized with hard drawn steel spring fixed on floor complete all as specified and directed.

S&F of MS Framed brackets of angles or tees with web and flanges pipes etc cut to shape drilled and counter sunk for screw, including bending and welding angles as necessary guesset plates, riveting etc n exc 10 kg each brackets conforming to Fe 290. Gde-E-165.

M&L Walling of random rubble uncoursed well bounded bedded out solidly hearted built in CM 1:6 all as spd and directed.

M&Lfor Brick work with sub class ‘B’ bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 all as specified and directed.

M&L Pre-Cast Cement Concrete block masonry type C1, 1:3:6 (using 20mm graded stone aggregate) with solid blocks exc 10 cm in width and setting in CM 1:4 all as specified and directed.

M&L Hardcore guage (broken stone or boulders) exc 63 mm n.exc. 100 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rolled / rammed to a true surface all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in floor / plinth protection including finished even and smooth without using extra cement all as specified and directed..

M&L cement concrete type B1, 1:2:4 (20mm graded Aggregate) as in floor / platform finished surfaces even and smooth without using extra cement.

M& L Plain cement concrete 1:4:8 Type D2 ( using 40 mm graded stone aggregate) as in sub base in 75mm thick all as specified.

M&L for rendering 10mm thick in cement plaster on fair surfaces of brick work / concrete/block masonary/ for fixing tile in cement motor 1:4 , finished and smooth without using extra cement all as specified and as directed.

M&L for 20mm thick damp proof course to horizontal or vertical surfaces including necessary formwork in cement mortar 1:2 all as specified and directed.

Material and labour for non skid colour ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set & jointed in neat cement slurry & pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6 for laying floor finish complete all as specified and directed.

M&L for glazed ceremic coloured tiles of size 300x200x7mm thick as in skirting/dados set and jointed in neat cement slurry and pointed with coloured cement to match all as specified and directed.

M&L for glazed ceremic coloured tiles of size 450x300x7mm/*400x300x7mm thick as in skirting/dados set and jointed in neat cement slurry and pointed with coloured cement to match, non skid joint free tiles all as specified and directed.

M&L for Rendering 15 mm thick cement plaster on fair faces of brick work/concrete in cement mortar 1:4, with water proofing compound finished even and smooth without using extra cement all as specified and directed.

M&L for Rendering 5 mm thick cement plaster on ceiling in cement mortar 1:3, finished even and smooth without using extra cement all as specified and directed.

Supply only integral water proofing compound ISI marked as approved.

M&L for two coat of synthetic enamel paint over a coat zinc chorome primer, incl preparing new steel surfaces any description, over 10 cm width or girth, not otherwise described.

M&L for preparation of new plaster surface with two coat of OBD over a coat of primer complete all as specified and directed

M&L for preparation of new plaster surface of ceiling with three coat of white wash over a coat of primer complete all as specified and directed

Use and waste of form work to sides and soffits of floor or roof beams, shelves and similar other works including supports for fair finished surfaces on concrete.

M&L for Form work to soffit of suspended slab such as roof slab, floor slabs landing and similar work not exceeding 200 mm thick horizontal or slopping all as specified and directed.

M&L for reinforced cement concrete Type B1 1:2:4using 20 mm graded stone aggregate in Roof Beams all as specified and directed.

M&L For reinforced cement concrete type B1 1:2:4 ( 20 mm graded aggregate) Slab supported on walls, beam and columns in floor, roofs, slabs and in shelves all as specified and directed.

M&L For reinforced cement concrete type B1 1:2:4 ( 20 mm graded aggregate) beams, cantilevers, bressummers lintel over 1.5m span

Supply and fix mild steel TMT bars, 10mm and over and cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Supply and fix mild steel TMT bars, 6 to 8mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for Rendering 5 mm thick in cement mortar 1:3 on top of roof slabs mixed with water proofing liquid as per manufacturers instructions, out of make : As approved by GE, finished even and fair complete all as specified and as directed.

Supply and fix pre painted galvalume aluminum zink coating GI base corrugated steel 0.5mm thick of any colour having tensile strength of 550 MPA as in roof covering/cladding to wall fixed with self tapping screw with minimum 150mm end lap and one corrugation side lap complete all as specified and directed.

M&L Providing precast cement concrete louvers and jallies, 65 mm thick (measured solid), including all moulding, set in cement mortor 1:4 type B-0 1:2:4 (12.5 mm gradedaggregate), (upto four storey building) all as specified and directed by Engr-in-charge.

S & F PVC connection 15mm dia 450 mm long with 2 Nos brass check nuts with washer etc complete all as specified by Engr-in-charge.

S&F PVC valveless, syphonic action type flushing cistern low level, white, with inlet, ball valve, float and handle incl brackets capacity 10 ltrs and connection to pipe complete.

S&F viterous china wash basin, white flat back size 550mm x 400 mm including brackets with waste pipe including cutting for and pinning in ends of brackets or erecting stand with grating fixing to floor making good, fancy type complete all as specified and directed.

S & F PVC (SWR) gully trap 125 / 110 mm including setting and jointing with solvent cement and removing old trap and making good all as directed by Engr in Charge

S & F Pillar taps 15mm dia cast copper alloy with capstion heads, chromium plated , fancy type screwed down high pressure, with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts screwed for 15mm dia pipe all as specified

Supply and fix bib taps 15 mm bore chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

Supply and fix single concealed stop valve chromium plated 15 mm bore, iron pipe or union screwed both ends complete all as specified.

S& F in repairs Soap dish, vitreous china white approximate size 160X160X90mm all as specified and directed

Supply and fix in repairs chromium plated brass, towel rail 20mm dia, D type 60 cm long between flanges, including a pair of CP brass brackets complete all as specified and directed

S&F Fixed in repair of viterious china wash down water closet pan (padestal pattern), superior fancy type white (excl fixing bolt, flushing cistern and flush type) incl connection to drain (or outgoing pipe) and to flushing pipe, anti shyphonage etc with seat cover complete all as specified and directed.

S&F in repair ASTM 1784 Sch 80 class III pipe fixed complete to walls, ceiling or in floors etc, including taking down existing pipe, etc in(Upto four storey building) including using of necessary scaffolding of 16 mm dia all as specified and directed.

All as per item no 63 above but for 20mm dia

S&F UPVC pipe pressure rating 10kgf/CM2 fixed complete to walls, ceiling or in floors etc any type of pipe 15mm bore UPVC tubing

all as per item No 65 above but for 20 mm bore UPVC tubing

S&F PVC ( SWR) soil waste pipe in any length double socketed with rubber ring jointed laid in trenches or in floors 110mm dia bore of pipe ISI marked all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to walls, including necessary brackets all as specified and directed .

Shilpa Engineers and Contractors

KEERTHI CONSTRUCTIONS