UDP-88 (2025-26) GRANT

Name Of Work : CONSTRUCTION OF INDUSTRIAL PROFLEX SHED AT PRANTIJ NAGARPALIKA AREA AT

Schedule-B1 :CONSTRUCTION OF INDUSTRIAL PROFLEX SHED AT PRANTIJ NAGARPALIKA AREA AT PRANTIJ.

Sr. No. Description Quantity Unit Rate Amount

1 Excavation for foundation upto 1.5M depth including sorting out and 268.08 Cu.M. 212.52

stacking of useful materials and disposing of the excavated stuff upto

Loose or Soft Soil.

2 Excavation for foundation for depth from 1.5 m to 3.0 m including 74.06 Cu.M. 235.05

sorting out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead.(A) Loose or soft soil

3 Providing and laying cement concrete 1:3:6 ( 1: Cement : 3- Coarse 179.42 Cu.M. 3095.25

Sand : 6- hand broken stone aggregates 40mm nominal size) and

curing complete excluding cost of formwork in

(A) Foundation & Plinth

4 Providing and laying controlled cement concrete M.250 and curing 202.18 Cu.M. 4345.72

complete excluding the cost of formwork and reinforcement for

reinforced concrete work in (A) Foundations, footings, Base of

columns and Mass

5 Providing formwork of ordinary timber planking so as to give a 301.62 Sq.M. 181.85

rough finish including centering, shuttering, strutting and propping

and centering below supporting floor to ceiling not exceeding 4M.

And removal of the same for in sity reinforced concrete and plain

concrete work in

( A ) Foundation, footing, Base of Columns and mass concrete

6 Providing and laying controlled cement concrete M.250 and curing 40.07 Cu.M. 4734.71

complete excluding the cost of formwork and reinforcement for

reinforced concrete work in (D) Columns, Pillars posts and struts,

upto floor two level.

7 Providing formwork of ordinary timber planking so as to give a 311.64 Sq.M. 315.74

rough finish including centering shuttering strutting and propping

etc. height of propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (G) Columns

PillarsPosts and struts. (1) Square Rectangular Polygonal in plan.

8 Providing and laying controlled cement concrete M.250 and curing 81.90 Cu.M. 4629.30

complete excluding the cost of formwork and reinforcement for

reinforced concrete work in (C) Slabs,landing,shelves,Balconies,

Lintels, Beams, Girders and Cantilever upto floor two level.

9 Providing formwork of ordinary timber planking so as to give a 540.00 Sq.M. 205.26

rough finish including centering, shuttering, strutt``ing and propping

etc. height of propping etc. height of propping and centering below

supporting floor to ceiling not exceeding 4M. And removal of the

same for in sity reinforced concrete and plain concrete work in

(H) (1) Sides and soffits of beams, beam haunchings, cantilever,

girders bressumers, and lintel not exceding 1 m in depth

10 Filling available excavated earth ( excluding rock ) in trenches, 268.08 Cu.M. 136.92

plinth, sides of foundation etc. in layers not exceeding 20cm in depth

consolidating each deposited layer by ramming and watering.

11 Filling, Foundation & Plinth with murrum or selected soil in layers of 600.00 Cu.M. 294.39

20 cms thickness including watering , ramming and consolidation etc

12 Providing TMT Bar FE 550D reinforcement for R.C.C. work including 26233.90 Kg 77.29

bending, binding and placing in position complete upto floor two

13 Brickwork using common burnt clay building bricks having crushing 24.66 Cu.M. 4214.33

strength not less than 35kg/Sq.cm. In foundation and plinth in

Cement mortar 1:6 ( 1-Cement :6- Fine Sand )

(B) Conventional

14 Brickwork using common burnt clay building bricks having crushing 101.52 Cu.M. 4495.98

strength not less than 35kg/Sq.cm. In foundation and plinth in

Cement mortar 1:6 ( 1-Cement :6- Fine Sand )

(B) Conventional

Extra for brickwork in super structure above floor two level

15 Providing 15mm thick cement plaster in single coat in 663.60 Sq.M. 184.78

brick/concrete wall for interior plastering upto floor two level and

finished even and smooth in

(I) Cement Mortar 1:3 ( 1-Cement : 3-Sand)

16 Providing 20mm thick sand faced cement plaster on walls upto 636.00 Sq.M. 321.10

height 10mt. Above ground level consisting of 12mm thick backing

coat of C.M. 1:3 ( 1-cement : 3-sand ) and 8mm thick finishing cost of

C.M.1 :1 ( 1-Cement : 1-Sand) etc. complete.

17 Supply & Installation of Self-Supported K-Span Roof. With sheet 800.00 Sq.M. 2525.00

thickness -1.20 mm BMT and PPGL-Color Coated Galvalume Sheet-

Standard (Alluminum+Zinc Coated) Galvalume Alloy Coating AZ-

150,Yeild Strength-300-350MPA Top Coating- 25 mic. & Bottom

coating-12 mic. (incl. primer Epoxy.) RMP Coating ,SMP Coating

Thick. Variation - ±0.05 MM , Width – 912/914 MM (Tolerance = ±

MM)-Dimensions :-Span ( Mtr ) 25.00 Mtr 82.00 FT Length ( Mtr )

40.00 Mtr 131.20 FT Arch Rise ( Mtr ) 5.00 Mtr

Effective Span ( Mtr ) 29.00 Mtr (No. Of Bays

18 Providing corrugated G.I. sheets roofing fixed with galvanised iron 200.00 Sq.M. 734.19

“J” or “L” hooks bolts and nuts 8 mm diameter with bitumen and G.I.

limpet washeres, filled with white lead complete excluding the cost

of purlins rafters and trusses (1) 0.80 mm thick sheet.

19 Painting two coats ( including priming coat ) on new steel and other 448.60 Sq.M. 129.04

metal surface with snthetic enamel paint ,brushing to give an even

shade including cleaning surface of all dirt, dust and other foreign

20 Providing and laying cement concrete flooring 1:2:4 ( 1-cement : 2- 800.00 Sq.M. 352.01

coarse sand : 4- graded stone aggregate 20mm nominal size) laid in

one layer and finished with a floating coat of neat cement.

21 Finishing Wall with Weather Proof Exterior Emulsion Paint on wall 636.00 Sq.M. 65.25

Surface (Two Coats) to give an required shape even shade after

throughly brushing the surface free from mortar dropping and other

foreign matter and sand papered smooth.

22 Wall Painting (two coats) with plastic emulsion paint of approved 663.60 Sq.M. 82.97

brand & manufacture on under coated wall surface to give an even

shade including throughly brushing the surface free from mortar

dropping and other foreign matter and sand papered smooth.

23 Supplying and erecting LED street light / Flood light fittings with 8.00 No. 7266.95

High power White LEDs wattage of 3 Watt and above assembled on

single MCPCB, efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more

than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio

>0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency >

85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.) (B) Flood Light (IP-65), Surge

protection -4KV integral and ,Light must have 440VAC line supply

with over-voltage protection. (iv) above 90 to 120 watts Cat-lll

24 Point wiring for Light/ Fan / Bell with 2-1.5 sq.mm & earthwire of 20.00 No. 387.84

1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires, in following type of pipe to be

erected concealed in/ on surface on wall/ceiling complete with 6A

Modular type switch / bell push & accessories and earth continuity

of following type, erected on PVC / Metallic box, single mounting

base frame covered with textured/metallic front plate modules

erected on / in wall / ceiling as per pipe erected, with necessary

Lamp holder/ceiling rose / H.D.Connector as directed.(a) with

medium class Rigid PVC pipe and accessories cat III

25 Providing following type of Modular Type Accessories mounted with 20.00 Ea 49.49

PVC / metallic/Wooden box, single mounting base frame covered

with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In

(9) 16 Amp. SP one way switch

26 Providing following type of Modular Type Accessories mounted with 20.00 Ea 78.78

PVC / metallic/Wooden box, single mounting base frame covered

with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In

(10) 6/16Amp. Universal socket

27 Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded 200.00 mtr 59.59

Copper conductor wire in following type of pipe to be erected

concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for

earth continuity of following size (a) with medium class Rigid PVC

pipe and accessories (a) 2 wire 1.5 sq. mm

28 Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded 400.00 mtr 78.78

Copper conductor wire in following type of pipe to be erected

concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for

earth continuity of following size (a) with medium class Rigid PVC

pipe and accessories (b) 2 wire 2.5 sq. mm

29 Providing & Erecting following Shockproof tissino type accessories 30.00 Ea 21.21

erected on 3 mm thick PC (Polycarbonate) sheet in PVC/ Metal Box.

erected on wall/ ceiling. (8) Bakelite lamp holder

30 Supplying KITKAT pattern porcelain cut-out with base of following 6.00 Ea 278.76

current capacity erected on existing block board.(v) 100 A. 500 V

31 providing and erecting Miniature circuit breaker single pole 6A to 16.00 Ea 112.11

25A suitable to operate on 240 V A.C. system and having breaking

capacity 10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark

32 Providing & erecting 415 V MCB Four Pole for Motor & Inductive 4.00 Ea 737.30

Load (C Curve) having 10KA breaking capacity & confirms to IS

:8828 in existing box having following capacity (c)63 Amp cat III

33 Providing and erecting Sheet Steel powder coated MCB distribution 2.00 Ea 885.77

board - flush / surface mounted fitted with busbar, neutral link,

earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be

used of same company of MCB to be used) suitable for

(A) single phase incoming and horizontal single phase outgoing

(b) sheet steel double door (IP-43)

34 Supplying & erecting earth pit of minimum bore dia.150mm size 2.00 Ea 5760.03

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover.(approved make OEM has to submit test

certificate) & having back filling compound of (B) Inner chemical

(CCM Compound)- Resistivity:- 0.2 / meter testing as per IEC

62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar

content:- <2%(C) Back fill Compound :- Earthing compound should

be capable to retain moisture for long time Necessary test report

must be submitted.

(b)For Electrical installation up to 11 KV in normal soil.

Length of Pipe : 2.00 mtrs

Back filling Compound :1 no. Bag of 25 Kg.

35 Providing and fixing rolling shutters of approved make made of 80 50.00 Sq.Mt 4546.01

mm wide M.S. laths inter-locked together through their entire length

and jointed together at the ends by end locks mounted on specially

designed pipe shaft with bracket plates, guide channels and

arragements for inside and outside locking with push-pull operation

including the cost of hood cover and spring etc. complete. (B)

Shutters having width 3.5 M. and above

36 Supplying & erecting single phase approved make industrial exhaust 20.00 Ea. 4646.00

fan suitable for medium duty ring mounted low noise operation

suitable for medium duty having following dia size and maximum

[E] 450 mm dia 1400 RPM

37 Providing and fixing M.S. grills of required pattern to wooden frame 2430.00 Kg. 106.29

of windows with M. S. flat at required spacing & frame alround,

square or round bars with round bars with round headed bolts and

nuts or by screws.

38 Providing and fixing extruded aluminum window having extruded 48.60 Sq.M. 2140.33

aluminum Colour Powder Coated section frame main outer size

127mm x 38.10mm x 1.35mm (of Jindal Section no:2443,@ Wt.1.384

Kg/mt),horizontal Four track member size 122.20mm x 31.75mm x

1.10mm (of Jindal Section no:8787,@ Wt. 1.205 Kg/mt),vertical

member of size 122.20mm x 31.75mm x 1.50mm (of Jindal Section

no:8935,@ Wt. 1.398 Kg/mt) with sliding shutters of horizontal

member size 40mm x 18mm x 1.29mm (of Jindal Section no:8949 @

wt.of 0.456Kg/mt),vertical member of size 40mm x 18mm x 1.29mm

(of Jindal Section no:8947 @ wt.of 0.456Kg/mt/Section 8948,@ Wt.

0.457 Kg/mt) with 5 mm thick transparent bronze colour tinted float

glass with powder coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame as per details etc

complete for window.

39 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 48.00 R.Mt. 339.05

working pressure poluthene pipes of the following outside Dia. Low

densidy, complete with special falnge compression type fittings, wall

clipsetc. including making good the wall ceiling and floor.(G)110 mm