Renovation of AMD Labstores

Amount

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 150 m outside the periphery of the area cleared

Felling or Cutting of dead/dried tree having a girth between 120 cm and upto 240 cm ( measured at a height of 1.0m above ground level) at locations with all required safety scaffolding including cutting the trunk and branches into small pieces, removing the roots , and transporting and stacking within a lead of 200 m etc., complete with cost of labour, tools & plants etc all as per the directions of Engineer-in-Charge.

Dismantling oldplaster upto exposed brick wall/skirting carefully,raking out joints and cleaning the surface for plastering including disposal of rubbish to the dumping ground within 150 m lead as per directions of EIC

Dismantling of existing glazed tile dado/ Kota stone/marble/ mosaic skirting/tandur flooring/platforms/ceramic tile flooring, together with cement mortar base of full thickness upto brick work at all floors and locations including stacking of materials and disposing off the debris within a lead of 150mtrs., lift of 25.0mtrs. all as per specifications and directions of Engineer-in-charge.

Removing the existing urinal partitions of 18mm thk. granite slabs carefully from cement morter 1:3 all complete with cost of labour charges, tools & plants all as per specifications and directions of E-I-C.

Providing 20mm thick Internal plastering in C.M 1:4 (using river sand)finished smooth,including sieving of sand to required fineness,preparation of the surface,scaffolding,curing all as per specifications,drawings and as directed at site complete.

Providing and fixing Glazed VITRIFIED floor and skirting tiles Using Tiles of size including 600x600mm and upto and including 900 x 900mm of approved make in different sizes conforming to IS15622 in all colours (two colors preferably) and shades in Glossy or Matt or satin finish laid over a bed of minimum 20mm thick bed of cement mortar1:4 (river sand) after removing the top surface of IPS flooring until the rough/hard surface is exposed and also removing and refixing the doors after resizing while laying the flooring wherever necessary (hardware if required for fixing the door shall be provided by Department at free of cost) and jointing the tiles with grey cement slurry including grouting with the joints with white/matching cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications and final cleaning of site complete as directed by the Engineer-in-charge

Providing and fixing 1st quality antiskid /non slippery ceramic tile flooring conforming to IS of approved shade, pattern, design & colours (including dark shades) of minimum size 300 x 300mm / 400 x 400 mm manufactured by M/s Kajaria, M/s RAK Ceramics, M/s Bell Ceramics, , NITCO / HR Johnson or equivalent approved make at all floors and locations laid over 20mm thick or more asper site conditions cement mortar 1:3 bedding / backing close jointed and grouted with polymer based cementatious tile joint filler with Tile Grout compound of ROFF/Balendura , matching with the colour of tiles, laid to required slopes making openings or cut-out if necessary, wastage and also removing the top surface of existing flooring until the rough/hard surface is exposed and also removing and refixing the doors after resizing while laying the flooring wherever necessary (hardware if required for fixing the door shall be provided by Department at free of cost) and final cleaning of surfaces as required curing etc., complete as per specifications and directions of Engineer-in-charge.

Providing and laying of 1st quality colour ceramic glazed wall tiles conforming to IS15622 in dados of approved shades, pattern, design & colours including darker shade for required height portion as per approved pattern and design of any size 320 x 480mm / 300x600mm / 300x450mm manufactured by M/s Khajharia, M/s RAK Ceramics M/s Bell Ceramics, NITCO or Johnson or equivalent approved make laid over 20 mm or more thick (i.e, mortar shall be laid from exposed brick work for tile backing whereever necessary, no extra will be paid for the extra mortar) cement mortar 1:3 (1 cement : 3 sand) bedding / backing and fixing the tiles with cement slurry and pointing the joints with matching colour Tile Grout compound of ROFF/Balendura finished to line, level, slope, and plumb including cutting of tiles, making cut outs / opening wherever necessary, wastage, final cleaning of surfaces as required, curing etc., complete with cost of materials, labour, tools & plants, scaffolding, final cleaning of site all as per specifications and directions of engineer-in-charge.

Applying wall care putty manufactured by M/s Birla or M/s J K cements in two or more coats for areas more than 0.1m2 and finishing the surface smooth in level and even on the existing oil Bound/Acrylic washable Distemper painted surfaces of the walls and ceilings at all floors, levels and locations, including removing the damaged / loose portions of the OBD /Acrylic washable distemper together with lappam /POP/putty base by scratching with lappam putty blade, sand papering, thoroughly washing with water, filling the paint removed portions with putty, preparing the surface by sand papering, removing stains, oil marks, cob webs, etc., scraping, filling cracks, and crevices upto 1 mm width with approved crack filling compound, cost of all the materials, tools and plants, labour, scaffolding, cleaning, floors, removing office furniture / Lab equipment and rearranging back the same etc all complete as per specifications and directions of Engineer-in-charge.

Painting on internal surface of ceilings and walls at all floors heights and locations (upto maximum height of 25 m) using 1st quality oil bound Distemper of approved make in two or more coats over the existing painted surface or primer coated surface including preparing the surface by sand papering cleaning and removing the dust, dirt, loose painting, grease, oil stains, cobweb, fungus etc., and filling up small cracks upto 1mm width using approved crack filling compound and applying wall care putty manufactured by M/s Birla or M/s JK Cements wherever necessary for areas upto a 0.1 m2 (beyond this it shall be measured separately in the respective item) complete with cleaning floors, removing office furniture / Lab equipment before painting and rearranging back the same etc., all complete with cost of materials, labour, scaffolding, tools & plants all as per specifications and directions of Engineer-in-Charge.

Painting with first quality exterior anti-algae,weather proof acrylic smooth emulusion paint of approvedof M/s Asian Paints or Weather Coat Smooth of M/s Berger Paints or approved equivalent make and shade with / without a coat of corresponding Exterior emulsion primer of approved shade on the sand face plaster surfaces (new or painted) at all floors heights and locations (upto a maximum height of 30 m) including filling up the small cracks and crevices, with approved filling compound, cleaning ,washing, removing the dust, dirt, scales, grease, oil marks, loose painting thoroughly sand papering, wire brushing if necessary, complete with cost of material, labour, scaffolding, tools & plants etc., all as per specifications and directions of Engineer-in-Incharge. Note: A co-efficient of 1.50 shall be applied over the area measured flat on the rough cast surfaces to get equivalent plain area for payment.

Providing and painting of Synthetic Enamel painting in two or more coats using 1st quality SE paint- Apcolite Synthetic Enamel of M/s Asian paints, or Luxol Hi -Gloss Synthetic Enamel of M/s Berger Paints or approved equivalent make and shade over wood/steel /concrete/road kerb stones surfaces of internal areas at all floors heights and locations (upto a max height of 25 m) including filling up small cracks and crevices with approved filling compound, cleaning, washing, removing the dust, dirt, scales, grease, oil marks, loose painting thoroughly, sand papering wire brushing if necessary, complete with cost of materials, labour, scaffolding, tools and plants all as per specifications and directions of Engineer-in-charge.

Providing &Fixing 1st quality Counter wash basin of size 500/ 545mm x 440mm, make: Parryware make consisting of following items of work. a) Providing & Fixing white glazed vitreous chinaware wash basin over CI brackets which will be grouted inside the wall in concrete b) Cutting the holes or chases in wall, floors etc.,& redoing to its original condition, painting all the metallic parts with 2 coats of approved synthetic enamel paint over a coat of primer and finishing the gap with white cement etc. c) proving & Fixing 15mm dia PVC inlet connection d)Providing &fixing 15 mm n.b. screw down heavy quality C.P. brass stop cock of M/s .Jaguar make Cat no: 053 to the wash basin e) Proving & fixing CP brass pillar cock of M/s. Jaguar make cat. No: 011 f) Fixing 32mm dia C.P. bottle trap with extension piece and wall flange, waste coupling to the wash basin g) Installation and testing the entire assembly to the full satisfaction of Engineer-in-charge and rectifying the leakages etc., if any. Including making jointing leak proof and making good the surface to original type all complete as per specifications and as directed by Engineer-in-charge

Providing and fixing 6mm thick mirrors of size 600x450mm of approved make with bevell ededge complete with 6mm thick asbestos sheet background fixed to walls with C.P.brass screws and concealed washers complete.all as per specifications and as directed by the Engineer-in-charge .

Providing and fixing C.P brass bib cock of heavy quality of specified/ approved make as per specifications and as directed by the Engineer-in-charge

Providing & laying / fixing in position machine cut, mirror polished 18mm granite slabs of Jet black/pink or any other approved colour & quality including machine cutting, polishing, buffing the edges half round for treads, full round for urinal partitions, plotforms, steps by making necessary grooves into wall all in line, level,(curvature corner if required) in cement morter 1:3 with finishing,curing etc. completeas per directions of EIC.

Providing and fixing 150 x 100 mm size gully trap "P" type square mouth S.W. Gully trap complete with CI grating brick masonry chamber with water tight CI cover with frame of 300x300mm size (inside) the weight of cover to be not less than 4.5 kg and frame to be not less than 2.70 kg as per standard design

Supplying and fixing on exposed / consealed on internal and external areas surfaces the following diameter CPVC pipe SDR 11 to with stand a temperature up to 120°C conforming to IS15778 manufactured by M/s. Ashirvad / Astral or equivalent approved make with CPVC fittings with brass threaded and specials like ,male adopters, bends, elbows (brass threaded), sockets, tees(brass threaded), unions, reducers, extension nipples, enlargers, cross Tee etc., with ISI mark consisting of the following items of work including fixing the pipe and specials with CPVC solvent joints for water supply line with M.S. nails, wooden gutties and `U' type plastic clamps having not less than 2mm thick complete with cost of materials, labour, tools & plants, scaffolding all as per specifications and directions of engineer-in-charge. a. Cutting or making hole or chases in the RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc., for passing the pipe line and re-instating all the damage to its original condition. b. Testing the pipe line to a hydraulic pressure of 10 Kg/cm2 for leak proof joint. NOTE: Nothing will be paid extra for GI pipe line/CPVC & specials for making connections with the existing GI /CPVC pipe laid by other agency or already available at site.

20mm dia

Replacement of broken or damaged Asbestos cement corrugated plain /curved sheets or G.I. sheets from the roofs of car shed / scooter shed / stores shed at all heights and locations including removing the existing broken/ damaged sheets together with J bolts, nuts, washers and providing and fixing new A C or PPGI sheets with new J bolts/ nuts/washers/MS stiffener flat pieces, disposal off the debris with in a lead of 150 mts etc all complete with cost of scaffolding, labour,materials, tools & plants etc., all as per specifications and directions of Engineer-in-charge.

General Notes: 1. Contractor shall inspect the site to acquaint with the site conditions as well as security conditions at AMD Labstores, Near ECIL, Hyderabad. 2. All the dismantled/ demolished materials shall be dumped at one place as decided by the department within the lead of 150.0mtr. 3. All the samples of materials which are to incorporated in the work shall be got approved by the Engineer -In- charge well in advance. 4. It is the responsibility of the contractor to handover the dismantled items to Dept. At site. Contractor shall be held responsible for any shortage/ missing of dismantled items untill handing over the same to dept.stroes. 5. The contractor is required to pay his employees / labour as per the prevailing minimum wages approved by State/ Central Govt. The contractor shall maintain 1. Register of Workmen employed 2. Muster roll 3. Register of wages etc. 6. Contractor shall quote rates for all items after considering cost of materials and labour components and all such conditions leads, lifts, safety precautions, security restrictions that are necessary for satisfactory completion of work as per instructions and site conditions. Security regulations shall be followed. 7. The rates quoted shall include cost of all tools and tackles, manpower including wages, liveries, all wastages and GST,water charges,Labour cess seignorage charges etc. as applicable but exclusive of EPF and ESI. EPF and ESI are reimbursable as per relevant clause on production of proof of payment as per CPWD norms. 8.The contractor has to follow all safety rules of the department and all safety equipments, PPE shall be provided to all workers engaged by him. 9. The contractor shall use only river sand confirming to IS 383 for all cement works involved in the scope of work. 10. The site shall be cleaned and handded over to Dept. after completing the all works as specificed in the tender in all respects. No extra payment will be made for cleaning.

E SAIDULU

P.V.RAJU