GENERAL Mammilikkadavu r o a d F e r o k e I m p r o v e m e n t s t o Mammilikkadavu road Providing 40 mm MSS General Electrical Work

Amount

Providing Street Light

OD178413/2025-2026:Supply Conveyance, installation, testing and commissioning of 30W LED decorative luminaire Colour Temperature 3000-5700 K with IP 65 protection and IK09 impact resistance with power factor greater than 0.95 at full load, internal surge protection 4 KV, Spun & Extruded Aluminum body Powder coated finish, Convex type clear acrylic diffuser complete with THD less than 10%, power factor greater than 0.95,duly wired up for use on 240 V AC supply.With MS decorative pole of 4270mm height with single arm ,foundation bolts etc as required.( LED luminaire Make K-LITE code 5187 A11 Karona Fort Mini , DecorativePole K-LITE code 2011-427-G35-SA DRIVEWAY ORNA FLORUS Series or Techno commercial equivalent approved by engineer in charge)

OD182242/2025-2026: Supply Conveyance, installation and commissioning of Lighting Pole 2550mm made of circular mild steel pipe (grade YST 210) 88.9mm Dia x 2.9mm thick with 2538mm Height. Decorative base made of Gravity Die-cast aluminium (330mm Dia x 806mm Height). Pole section welded by certified welders using high end MIG welding processes. GDC aluminium inner service door 348mm height x 80mm width shall be provided with the company logo embossed on the bottom of the door and safety rope & Outer service door on decorative base 273mm height x 56mm width. The control gear tray is prewired with 2.5 Sq.mm cable, 6A SP MCB and 32A Ramanuj stud type 4 way terminal block for loop in / loop-out arrangement, 5A 2 Way terminal connector and provision for earthing. Any other internal cables and connections shall not be covered in the scope of supply. Mild steel mounting plate 200mm Square x 12mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 300mm bolts of grade 4.6 at CC140. The base plate have a cable entry hole as per the base pipe size. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension are within +/- 5% tolerance. After fabrication entire pole is shot blasted (Inhouse). The pole is coated with zinc rich primer & pure polyester powder coating or epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options . ( Lighting Pole Make K-LITE CAUSEWAY MIDI Series Lighting Pole code 12024-300 or Techno commercial equivalent approved by engineer in charge)

OD182243/2025-2026:Supply Conveyance, installation, testing and commissioning of 30W LED Post top luminaire. Symmetrical light distribution. Gravity die-cast aluminium top cover with gravity die-cast aluminium decorative knob on top, Die-cast aluminium supporting arm integrated with base suitable for mounting Ø50mm OD existing pipe. Translucent / textured acrylic diffuser. All external screws are made of stainless steel. Protection class IP65. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. .The Luminaire should be having Minimum 50000 Burning hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.95, THD <10%, Surge protection 4KV. Luminaire dimension : 325mm square x 545mm height. CE & BIS Certified. ( LED luminaire Make K-LITE Dynasty Midi ID : 4509 or Techno commercial equivalent approved by engineer in charge)

90.15.1.1:Supply installation testing and commissioning of Octogaonal Pole made of hot dip galvanised GI sheet 70mm top diameter. 130mm bottom diameter thickness 3mm base plate dimensions of 200x200x16mm suitable for windspeed as per IS 875 Part III fixed head frame including round arm luminary carriage suitable to install 4/6 nos luminaries in symmetrical arrangement including connector foundation bolt 4 nos existing RCC foundation and junction box etc, complete 8 Meters

90.15.4.7:Supply Conveyance, installation, testing and commissioning of 100W LED Flood light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD less than 10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

90.6.5.11:Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.3 core 1.50 sq mm

14.1:Excavation for foundation in soft soil including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metres.

14.10:Providing and laying in position reinforced cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc. including form work etc. as required (excluding reinforcement).

14.7:Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required.

OD178414/2025-2026:Steel reinforcement for RCC Work including straightening, cutting, bending, placing in position and binding all complete.

90.12.10.2:Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation50/38 mm or nearest size

90.12.5.40:Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.4 core 10 sq mm

OD190208/2025-2026:Supply & laying of DWC pipe through the wall/ parapet using clamps noted along with the DWC pipe, making good the damages colour washing etc. as required. 50/38 mm or nearest size

90.12.9.2:Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench50/38 mm or nearest size

90.16.2.1:Supply and laying of the following sizes of B class GI pipe laid 0.6 m below ground level including excavating trench of suitable size and refilling etc, as required.15.mm dia. G.I pipe ( medium class)

90.16.2.4:Supply and laying of the following sizes of B class GI pipe laid 0.6 m below ground level including excavating trench of suitable size and refilling etc, as required.40 mm dia G.I. pipe ( medium class)

9.1.32:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

7.10:Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

OD187652/2025-2026:Supplying and fixing 0.5 amps to 4 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB/panel board complete with connections, testing and commissioning etc. as required.Single pole

2.10.1:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

2.10.3:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

2.10.4:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

2.10.5:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole and neutral

OD179289/2025-2026:Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (Type A RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

2.13.1:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.21:Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

OD178415/2025-2026:Supplying and fixing 24Hours Digital Time Switch for operating ON-OFF function in the existing MCB DB/enclosure complete with connections, testing and commissioning etc. as required. (L&T make Digital Time switch 2 module cat no 67DDT0 or Techno Commercial equivalent approved by engineer in charge)

OD178419/2025-2026:Supply and fixing following rating Surge Protection Devices 4 module (3P+N) ,Conforms to IEC 61643-11, Type 1+2(Protection against direct and indirect lightning surges) ,I imp 12.5kA Maximum Discharge Current - Imax up to 50 kA in existing enclosure/cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. (Make L&K or Techno commercial equivalent approved by engineer in charge)

OD178420/2025-2026:Supplying and fixing following rating miniature type four pole AC change over switch with Centre OFF in the existing MCB DB/Enclosure complete with connections, testing and commissioning etc. as required. 40 A, 4 pole, 2 way. (L&T make or Techno commercial equivalent.).

OD179286/2025-2026:Supplying and fixing following rating type AC-1, 4pole contactor in the existing MCB DB/Enclosure/Panel board complete with giving necessary connections, etc. as required. 40A ( L&T make MCX 40 or Techno commercial equivalent.)

2.1.1:Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.32 Amp TP & N

OD178427/2025-2026:Supply and fixing 32 A Fuse base with HRC fuse link in the existing meter board and giving connections etc.

OD178428/2025-2026:Supply and fixing 32A, 2 way neutral link mounted on DMC/ SMC base in the existing box and giving connections etc. as required

OD186353/2025-2026:Supply and fixing 4 way suitable size heavy duty bakelite terminal connector and giving necessary connections etc.as required.

OD186351/2025-2026:Supply and installation of dust and vermin proof thermoplastic polycarbonate enclosure of 300 x 300 x 214mm size with hinged Transparent lid, hand operatable/locking screws, fixing rails, and with knock outs on side walls etc ,as required - environment friendly, recyclable, UV resistant, halogen & silicon free, anti acid & anti corrosive, degree of Ingress Protection IP 65 in accordance with IEC 60529, gasket material of enclosure is Polyurethane; while the gasket is internally embedded.fixing it on wall with screws , nuts ,bolts, washers etc are should be of stainless steel , making good the damages colour washing etc. as required. (Hensel make model Mi 9210 or Techno commercial equivalent approved by engineer in charge).

90.14.1.1:Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623. Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 2.00mm CRCA sheet, powder coated (excluding base frame)

90.14.2.1:Supply and providing 2mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.

90.14.3.2:Supply and providing heavy duty 'A' section neoprene gasket in the panel boardU' section rubber beeding suitable for 1.60/ 2.00 mm sheet

90.14.4:Supply and fabrication conveyance and installation of base frame of panel board using 75 x 40 mm rolled steel channel (ISMC)

90.14.5:Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board

90.14.7:Supply and providing copper earth bus in the panel board

OD187657/2025-2026:Supply and fixing Red, Green, blue, Yellow, Orange colours LED indicator, AC/DC, as required

1.17.22:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.4 x 4 sq. mm

1.17.31:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.4 x 6 sq. mm

OD179128/2025-2026:Supply and wiring with ISI marked, FRLS PVC insulated following size single core copper conductor cables for interconnecting the control devices/ equipments including the wiring firm by suitable tie/ tie mounts/ PVC duct etc with sockets as required. 1.5 Sq mm single run

OD179129/2025-2026:Supply and wiring with ISI marked, FRLS PVC insulated following size single core copper conductor cables for interconnecting the control devices/ equipments including the wiring firm by suitable tie/ tie mounts/ PVC duct etc with sockets as required. 4.00 Sq.mm single run

OD179130/2025-2026:Supply and wiring with ISI marked, FRLS PVC insulated following size single core copper conductor cables for interconnecting the control devices/ equipments including the wiring firm by suitable tie/ tie mounts/ PVC duct etc with sockets as required. 2.5 Sq mm single run

OD179134/2025-2026:Supply and wiring with ISI marked, FRLS PVC insulated following size single core copper conductor cables for interconnecting the control devices/ equipments including the wiring firm by suitable tie/ tie mounts/ PVC duct etc with sockets as required. 1 run 16 sq. mm

5.4:Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

OD178422/2025-2026:Providing and fixing 25 mm X 3 mm G.I. strip earth lead from the test joint to the earth plate

OD178423/2025-2026:Providing and fixing 2 X 25 mm X 3 mm G.I. strip test joint for earthing system

90.16.1.2:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required2.65 mm copper conductor (12 SWG)

90.16.1.3:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)

90.16.5.2:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.2.65 mm (12 SWG)

90.16.5.3:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

OD178424/2025-2026:Supply and provide 12x3mm brass nut and bolt etc. as required

OD178425/2025-2026:Supply and providing 25x3mm brass nut and bolt etc. as required

OD178426/2025-2026:Supply and providing 25x6mm brass nut and bolt etc. as required

OD178418/2025-2026:Painting letters or figures of the following sizes with enamel paint as identification mark to SB, DB, panel board etc as required 2.5 cm, 4 cm, 5 cm height

OD179136/2025-2026:Supply and fixing 40mm dia 6Kgf/cm2 PVC pipe including fixing the pipe at 60cm spacing. etc on wall with all required accessories and clamps etc. including cutting and making good the walls, painting the exposed portions etc. as required. (KSEB Service pipe)

90.3.17.3:Supply, conveyance and erection of the following sizes of 'B' class GI pipe in single section for post top lantern of all types on concrete base (excluding charges for concrete base and excavation) and painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer etc. as required.50 mm dia GI pipe

PRADEEP KUMAR.V.K (BID ID -2418943)

Bidder Name

PRADEEP KUMAR.V.K

SURESH.S