SPECIAL REPAIR TO TOILETS PORTION IN BLDG NO P-1449 AT AF STN JODHPUR AND PROVN OF KITCHEN CABINET IN SMQs AT BUNDELA ENCALVE AT AF STN JODHPUR (PHASE-I)

Amount

Special repair to toilets portion in Bldg No. P-1449 at AF Stn Jodhpur

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for (roof padding, concrete in sunken floor above ground floors) including roof treatment and removing from site all as specified and directed.

M&L for dismantling floor heart or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises and com[plete all as specified.

Taking down cement or cement lime plaster of any description on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc and complete all as specified

Wire brushing and cleaning top surfaces including taking out old roof treatment of tarrace or cement concrete including flashing and junction of parapets

M&L 10 mm thick plaster with CM 1:4 with water proofing compound @ 3% by weight of cement finish even and smooth surfaces without using extra cement. Water proofing compound shall be measured and paid seperately

M/L for cement concrete B-0. 1:2:4 (12.5mm graded aggregate) in padding finishing surface of concrete topping even and fair without using extra cement all as specified of average thickness 25 mm in slop 1:40 over roof

M&L for one coat of applied cold bituminous primer @ 0.5 kg/Sqm shall be applied on plastered surfaces including side wall all as specified and directed.

M/L APP modified membrane minium weighting 3 Kg/Sqm with polyster non woven polyster reinforcement ( weight not less than 150 gms/sqm )shall be laid by torch application method and overlapped by 100 mm in all sides as directed by Engr-in-Charge

M&L for light coloured Vitrified Ceramic tiles 9-10 mm thick area of each tiles not less than 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1:6.

All as per item No. 9.00 above but on vertical surfaces such as dados, skirtings and risers to steps, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on stone masonry surfaces.

M&L for joint free non skid ceramic tiles, coloured, 7 to 8 mm thick in floors etc. (square/rectangular) area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6

M&L for glazed ceramic tiles, coloured, 450x350x7mm thick on vertical surfaces such as skirtings, dados and risers to steps etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on stone masonry surfaces.

M& L for 15mm thick rendering on any type of wall in CM 1:4 on walls using integral water proofing compound @ 3% weight of cement , finished even and smooth without using extra cement and all as specified. (NOTE;- Water profing compound shall be measured and paid seperately)

M&L for rendering 15 mm thick in CM 1:6 on any type of wall surfaces finished even and smooth without using extra cement.

M&L rendering 10mm thick in CM (1:3) on stone masonry fair faces of concrete surfaces as in ceilling finished fair and even without using extra cement complete all as specified and as directed

Supply only integral water proofing compound ISI Marked

M&L for preparation of New plastered and unplastered surface of walls and applying two coats of wheather proof exterior emulsion paint over a coat of primer complete all as specified and all as directed

M&L for preparation of New plastered or unplastered surfaces of ceiling and applying two coat of white wash.

M&L for applying two coat of Oil emulsion distemper over a coat of primer (tint as approved by GE)including prepration of newly plastered wall surface and over a layer of wall putty complete all as specified.

M & L for 100mm thick Plain Cement concrete type C-2, 1:3:6 (40mm graded aggregate) as in sub base etc complete all as specified and directed by EIC.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engr-in-Charge.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, set and jointed in CM (1:4) with grey cement and With pigment complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded aggregate as in coping , including necessary form work complete all as specified and directed.

M&L for chequered cement concrete coloured tiles 30cm x30cm x 25mm thick set, jointed and pointed with grey cement and pigments in neat cement slurry laid over 15mm thick screed bed in CM 1:6. in floors and path complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting any guage thickness incl Nainital pattern as in roof covering complete all as specified.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges etc. fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm as directed by Engr-in-Charge at site with suitable arangement as required complete all as specified & directed.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, flashing, eaves board valley gutter of any shape etc, cut to designed shape (Jhhallar) as directed at site fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm as directed by Engr-in-Charge at site with suitable arangement as required complete all as specified & directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and complete all as specified and directed by Engr-in-Charge

Fixing in repair anodised aluminium snap grid for false ceiling fixed or laid/inserted to timber/GI aluminium framework with screws and complete all as specified and directed by Engr-in-Charge

S&F in repair for power coated Anodised aluminium snap grid frame work for false ceiling size of grid 605x605 mm all as specified.

M&L for 12mm thick Perforated particle board for insula-tion and accoustic purposes,60x60 cm in size, fixed at height upto 10 mtr of wall including two coats of oil emulsion distemper complete all as specified and directed by Engr-in-Charge

M&L for 12mm thick Perforated particle board for insula-tion and accoustic purposes,60x60 cm in size, fixed on snap grid false ceiling including two coats of oil emulsion distemper fixing at site height upto 10 mtr and complete all as specified and directed by Engr-in-Charge

S&F framed work such as grills gratings etc with ends of bars shoulders and/or riveted or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings frame work of water tanks and similar works conforming to Fe 290 gde E-165.

M&L for preparation of new steel and iron surfaces of any description exc 10 cm width or girth and applying two coats of synthatic enamel paint over one coat of red oxide primer complete all as specified and as directed by Engr-in-Charge.

M&L for plain cement concrete type B-1 (1:2:4) using 20mm graded crushed stone agg as in seismic and other similar bands shelves coping bed plates hold fasts plinth courses filling in pressed steel frame and the like finished fair and even incl necessary from work complete all as specified & directed.

Material & Labour for 75mm thick plain cement concrete C-1, 1:3:6 (using 20mm graded crushed stone aggregate) as in plinth protection/path finished fair and even without using extra cement complete all as spd & directed.

M&L for Pre-cast cement concrete factory made kerb stone with 1:3:6 type C1 (20mm graded Stone aggragate) solid blocks, exc. 10 cm in width and setting in mortar,CM 1:6 complete all as specified and directed.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) exc. 1.5 Sqm but n exc 4.00 sqmcomplete all as spd and as directed.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) n.exc. 1.5 Sqm complete all as spd and as directed.

S&F power coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F sheet glass 5.5 mm thick, ordinary quality and glazing with oil putty in square n.exc. 0.5 sqm in each paneand complete all as specified.

S& F for 4 to 5mm thick ACP sheet fixed with rubber beading in aluminium frame works complete all as specified and directed by Engr-in-Charge.

S&F aliminium extruded section body Door closer hydrau lically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed as directed by Engineer-in-Charge.

S&F aliminium Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed as directed by Engineer-in-Charge.

S&F factory made solid PVC door frame of size 50mmx47mm made out of 5mm wood grain printed PVC sheet reinforced with mS square tube etc complete all specified.

S&F fiber glass reinforced plastic (FRP) door frame of cross section 90mmx45mm having single rebate of 32mmx15mm to receive shutter of 30mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and choppedmat.Door frame laminated shall be 2mm thick and shall be filled with suitable wooden block in all the three legs.The frame shall be covered with fiber glass from all sides. M>S stay shall be provided at the bottom to steady the frame etc complete all specified.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified & directed.

S&F Factory made solid PVC door shutter 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam pvc sheet on the back face, & rails with suitable PVC sheet beading, and joined together with solvent cement, but both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges complete all as specified & directed.

S&F extructed aluminium alloy handles, fabricated type,anodised of size 150mm.

S&F Aluminium anodised barrel tower bolt of extruded section 200mm size

S&F Butt hinges,heavy weight cold rolled stainless steel of size 100mm.

Dismantling of existing water tank (PVC/RCC/AC) exc 500 ltr but n exc 1000 ltr capcity and removing from site complete as directed by Engr -in-charge.

S&F 1000 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl 20mm bore ball PTMT. valve high pressure with polythyne float and flynut complete in repair.

Taking up or down 15 mm dia steel tubing and connection and removal from site complete all as specified and as directed

Taking up or down 20 mm dia steel tubing and connection and removal from site complete all as specified and as directed

S & F 15 mm dia galvanized steel tubing, medium grade, with all fitting and fixed complete to walls celling or laid in floors all as specified and directed.

S & F 20 mm dia galvanized steel tubing, medium grade, with all fitting and fixed complete to walls celling or laid in floors all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of 100 mm dia

S&F in repair 75 mm bore UPVC (SWR) pipes type ‘A’, single socketed, in any length with rubber ring joints fixed to walls.

S&F in repair 75 mm bore UPVC (SWR) pipes type ‘A’, single socketed, in any length with laid in trenches or in floors

S&F in repair PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints laid in trenches or in floors

S&F in repair PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints fixed in walls.

S&F in repair PVC (SWR) door bends 110 mm dia with acess door

S&F in repair PVC (SWR), junction single, (Single T) equal or unequal 75mm with acess door

S&F in repair PVC (SWR), junction single, (Single T) with acess door 110 mm dia equal or unequal

M&L for 1st class hard wood as in plain solid staight chowkats and frames wrought framed rebated on the solid rounded or chamfered put to gather with glue pinned at joints complete all as specified.

M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats and complete as directed by Engr-In-charge

S/F Flush shutters, 40 mm thick paticle board core construction, with block board core and plywood face panels, commercial type on both sides and if one face is covered with deco rative face veneer with lipping/frame to match and complete as directed by Engr-In-charge

S&F extructed brass handles fabricated type polished of size 300mm.

S&F brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts and fixed of extruded section 300mm size

S&F brass butt hinges, with cast or sheet barrel and rolled of size 125mm.

S&F 300 mm long brass, sliding door bolt with sand or die-cast brass hasp staple(bolt type) and fixing bolt with rolled or drawn brass bolt and fixed.

M&L for preparation of old surfaces (plastered or unplastered) of walls including removing/scrapping down existing surface where ever necessary and applying two coat of oil emulsion distemper over two coat of wall care putty complete all as specified & directed.

M&L for preparation of old surface of walls and applying two coats of wheather proof exterior emulsion paint complete all as specified and all as directed

M&L for preparation of old plastered or unplastered surfaces of walls and applying one coat of white wash.

M&L for preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white wash.

M&L for preparation of old painted wooden surface of any description not otherwise provided over 10 cm width or girth and applying one coats of synthetic enamel paint and complete.

M&L for preparation of old painted steel surface of any description not otherwise provided over 10 cm width or girth and applying one coats of synthetic enamel paint and complete.

M&L for preparation of old surfaces (plastered or unplastered) of walls including removing/scrapping down existing surface where ever necessary and applying one coat (finish coat) of oil emulsion distemper white or approved tinted including removing existing nails, if any and filling the disturbed / surface, holes/voids with wall care putty/POP to achieve the smooth surface complete all as specified & directed.

M&L for preparation of old painted brick, stone, concrete, asbestos cement or plaster surfaces of any description, over 10 cm in width or girth not otherwise described and applying one coat of plastic emulsion paint.

M&L for preparation of old painted surface n exc 10cm in width or girth when unconnected wirh other painting all when painted in different tint and two coat of aluminium paint over one coat of aluminium red oxide and complete all as specified & directed by Engr-in-Charge.

Disconnecting existing water tanks exc 500 ltrs but n exc 1000 ltrs cap setting aside (or lowering if required) for repair cleaning etc and hoisting if required reconnecting and refixing in position. (cleaning repairing etc measured separartely) complete all as spd.

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long

S&F in repairs plastic water closet seat,black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and complete.

M&L for poviding and injecting chemical emulsion for post construction anti termite treatment along external wall where the apron is not proving using chemical emulsion at theart of 7.5 ltr per sqm of the vertical surface of the sub structure to a depth of 300mm including excavating channel along the wall and rodding etc complete all as specified and directed.

M&L for granite (of any type) tiles 20 mm thick machine cut in skirting/dado over and including 15mm thick rendering in CM 1:6 on stone masonry surfaces, jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed by Engr-in-Charge.

S&F in repair exterior single colour aluminium composit panel thickness 3mm to 5mm fixing on wall screws & tap in existing system hieght upto 30 fit incl colour of ACP is as per existing surface complete all as specified & directed by Engr-in-Charge.

Fixing only in repair exterior single colour aluminium composit panel thickness 3mm to 5mm fixing on wall screws & tap in existing system hieght upto 30 fit incl colour of ACP is as per existing surface complete all as specified & directed by Engr-in-Charge.

Taking down carefully copper/aluminum point wiring (Light/ fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc, stacking at site for reuse or removing materials to store for keeping in for taking credit and making good the disturbed surfaces / walls/ floors etc.

M&L for point wiring with 1.5 Sq. mm, multi-stranded copper conductor, single core, PVC insulated and unsheathed cable for phase and neutral, including 1.5 Sq. mm PVC insulated unsheathed multistranded copper conductor single core cable as earth continuity conductor (in green color) connected to common earth dolly, drawn in surface/concealed conduit heavy duty (HMS Grade), GI terminal boxes not less than 1.0mm thick fixed flush to wall surface, covered with & including 3 mm thick plastic laminated sheet top cover or including modular plates of required size for mounting switch and sockets etc. complete all as specified and directed for following : - Note : Quoted rates deems to be included cost of modular plate for mounting switches, sockets & regulators as required at site. Cutting into chases required for concealing heavy duty (HMS Grade) PVC conduits and making good to damaged surface shall be measured and paid separately under relavant item.

One light / fan point controlled by one switch one way.

One 3 pin 5 Amp switch & socket outlet on same board with other switches.

S&F switch single pole one way 6 Amps 230 volt 1 module.

S&F Socket modular 6 Amp 2/3 pin combined two module.

S&F Ceiling rose surface bakelite 65x50mm three terminal.

Fixing only exhaust fan 300mm sweep, Steel/PVC body AC single phase 230V of size 300m using 4 Nos 10mm x 100mm long wall fasteners, nut and washers and connecting up using flexible three core 0.5sqmm copper stranded conductor PVC insulated and PVC sheathed flexible wire through PVC flexible conduit from ceiling rose/connector to fan complete all as specified. NOTE: Exhaust Fan/wall fans taken taken down against item No 16 shall be used after complete civil work repair and minor repair of ceiling fans (like replace of rusted nut bolts, denting of blade, cleanig of dust etc)

Supply and fixing LED light fitting wall /roof mounted, Aluminium housing, 1 x 22 watt including LED tube with driver complete suitable body robust, corrosion resistant, superior finish and without any cracks or through holes. The system wattage of fitting should not be more than 20 watt ± 10%, surge protection of minimum 2 kV power factor should be more than 0.90 cool white colour, total harmonic distoration (THD) should not be more than 15%, lumen output should not be less than 90 lumens per watt, total input voltage range 140-280 V AC, colour rendering index should not be less than 80, corelated colour should be minimum 6000 degree kelvin complete all as specified and directed.Cat part no-LGLZU1X022XC (Zaquar)or equivalent.

Supply and fixing LED light fitting wall /roof mounted, Aluminium housing, 10 watt including LED tube with driver complete suitable body robust, corrosion resistant, superior finish and without any cracks or through holes. The system wattage of fitting should not be more than 20 watt ± 10%, surge protection of minimum 2 kV power factor should be more than 0.90 cool white colour, total harmonic distoration (THD) should not be more than 15%, lumen output should not be less than 90 lumens per watt, total input voltage range 140-280 V AC, colour rendering index should not be less than 80, corelated colour should be minimum 6000 degree kelvin complete all as specified and directed.Cat part no-LGLZ01X010XC (Zaquar)or equivalent.

NOTES FOR LED LIGHT FITTINGS & BULBS : (i) All LED light/luminare shall meet the provision laid down in IS - 16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part -II / Section 13. (ii) Contractor shall submit test report of LED street light fitting from Government accredited test laboratory for LM-79 and LM-80. (iii) Contractor has to furnish a replacement warranty of 02 years for LED light fittings complete including lamps from the date of completion of contract. The product will be replaced on site free of cost in the following case :- (a) Manufacturing defects. (b) Failure due to mechanical and electrical impact. (c) Drop in lumen (or lux at 1 m) below 90% of claimed values of lumen (or lux at 1 m) of the LED /Luminaries.

Special repair to toilets portion in Bldg No. P-1449 at AF Stn Jodhpur

S&F Brass handles, cast type polished bright of size 75mm complete all as specified & directed.

S&F stainless steel hinges, bright and polished and fixed of size 75mm, complete all as specified & directed.

S&F ball catches with 8 mm dia steel ball and brass body and striking plate including letting in and fixed as specified & directed by Engineer-in-Charge.

S&F cupboard shutter of required sizes at site made out of 18 mm thick WPC laminated board with decorative teak face density not less than 650 Kg/Cum, all the edges shall be covered with 2mm thick edge beading tape or 90 degree edge bend finish as per make and specification & the panel shall be fabricated using adhesive and screws where required complete all as specified & directed. Make : Rajshree or equivalent make.

&F 18 mm thick WPC plain board of required size in cup boards and similar works density not less than 650 Kg/Cum all the edges shall be covered with 2 mm thick edge beading tape or 90 degree bend finish as per make & specification & the panels shall be fabricated using adhesive and screw where required complete all as specified & directed. Make : Rajshree or equivalent make.

S&F 20 mm granite (of any type) slab machine cut bedded jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing to rest between walls by cutting grooves and to be used as shelves complete all as specified & directed.

M&L for glazed ceramic tiles, coloured, 450x300x7mm thick on vertical surface such as skirtings, dados and risers to steps etc., set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10 mm thick rendering in CM 1:4 on stone or brick masonry surface including taking out existing plaster/tiles as directed by Engineer-in-Charge.

New Vishvakarma Udhyog