SPECIAL REPAIRS TO BLDG NO P-277/05 TO 08 (04 X OR MD ACCN) OF 2 GUJ NAVAL UNIT NCC FATEHGUNJ, AT SECTOR A UNDER GE (ARMY) VADODARA.

Demolition of stone slabs and tiles of any description or thickness in floors & wall, laid bedded & pointed in any mortar.

Roughening of old unservicable PCC floor surface by picking, chipping and wire brush sweeping clean and washing down with water to remove dust outside to make it suitable for laying floor tile complete all as specified.

M&L for non skid coloured ceramic tile 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11sqm , as in floors etc set over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:4 including necessary adhesive (Tile pattern and decoration may be as suggested by Engineer-in-charge)

M&L for coloured ceramic tile 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38sqm , as in floors etc set over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:4 including necessary adhesive (Tile pattern and decoration may be as suggested by Engineer-in-charge)

M&L for colour ceramic tile 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38sqm , as in skirting etc set over and including 10 mm thick rendering with CM 1:3 including necessary adhesive (Tile pattern and decoration may be as suggested by Engineer-in-charge)

M & L for Glazed ceramic coloured walls tiles in vertical surfaces 300x450x 6mm to 7 mm thick set over and including 10mm thick rendering on vertical surface of wall or concrete surfaces in CM 1:3 to receive wall tiles including necessary adhesive (Tile pattern and decoration may be as suggested by Engineer-in-charge).

M & L for 18 to 20 mm thick machine cut green marbel stone in single piece in window/opening (Jambs/Cills) laid over cement screed and jointed with base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 10 mm thick plastering with cement mortar 1 : 3 including necessary adhesive complete all as specified

M&L Granite (of any type and colour) work (table rubbed and polished) 18 to 20mm thick in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match complete all as specified and directed.

M & L for machine cut kota stone slab flooring in cooking platforms and like etc. of 20 - 25mm thick (the stone may be in one piece) including rubbing and polishing complete set over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:4.

Taking down chowkats or frame with shutter (without taking off shutter from the frame) n.exc 1.5sqm each

Taking down chowkats or frame with shutter (without taking off shutter from the frame) Exc 1.5 Sq m but n.exc 4.00 Sq m each

M&L for 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, comercial type 1.0mm thick (veneered on both side) with decorative choice laminated type 1 (factory laminated), or surface finish, 6mm thick or external teak wood lipping fixed with nails, color and pattern as approved by EIC/GE.

S & F 35mm thick 2nd class Hard wood Glazed and Skelton shutters, open rebated and prepared to receive glass, gauze etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut ,mitered and moulded beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkats.

S&F of Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F 4.00mm thick figured glass, pin head type and glazing with rubber beading or with glazing clips n exc 0.5, all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

S & F Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolt, if required hooks (stay), heavy for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps hold fasts, wall ties, hooks for hanging fans, plain angles cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe 310-O or Fe 410-O

M & L Cement concrete type B1, 1:2:4 (20 mm graded aggregate) as in coping, bed plate for hold fast etc.

M&L for 100mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/Angle iron frame/PVC door frame with screw complete all as specified and directed.

M&L for 75mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/Angle iron frame/PVC/WPC door frame with screw complete all as specified and directed.

S & F 200mm long Aluminium anodised barrel tower bolt of extruded section and fixed with screws.

S & F 150 mm size extruded aluminium alloy handles, febricated type anodised fixed with screws.

S & F aluminium anodised Hasp and staple, safety type of size 75 mm with mild steel hinge pin including bolt to hinge plate and fixed with screws

S & F 250 mm aluminium alloy anodised sliding door bolts, with hasp and staple (bolt type) not less than 12mm dia with and and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast aluminium and fixed to wooden door shutters

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with fullbody threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid forseparately). ®Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed.

S&F Factory made single extruded WPC (Wood PolymerComposite) solid decorative flush door shutter of 30mm sizecomprising of virgin polymer of K value 58-60(Suspension Grade), calcium carbonate and natural Fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately complete all as specified and directed.

S&F in repair 18mm thick HDHMR BOARD exterior grade including any coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchen cabinets/cupboards etc all as per specified and directed by Engr-in-charge. Note: sample as approved by GE. Make: Action Tessa/Greenply/Century.

S&F in repair 18mm thick HDHMR BOARD exterior grade including white coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchen cabinets/cupboards etc all as per specified and directed by Engr-in-charge. Note: sample as approved by GE. Make: Action Tessa/Greenply/Century.

S & F 150mm aluminium anodised barrel tower bolts of extruded section and fixed.

S&F floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140mm anodised with hard drawn steel spring, fixed in floors complete all as specified and directed.

S&F magnet door stopper of rectangular size for PVC cabinets including all fittings fixed complete all as specified and directed.

S & F SS W Hinges SS 202 Grade steel Rust Resistance , for fixing cup boards shutters sizes of hinges 3" to 4" and 1.5 mm thickness, suitable for 18 mm thick cabinets shutters complete all as specified and directed

S&F 100 mm Pull door handles, chrome finish, Stainless steel of SS 304 grade all as per specified and directed by Engr-in-charge. Note: sample as approved by EIC/GE

S & F tubular curtain rails 25mm dia stainless steel 202 grade drapery type complete all as specified directed

S & F in repairs stainless steel socket fancy type with bracket for 25mm dia stainless steel tubular curtain rod (design of socket shall be approved by GE/AGE at the time of execution) as directed

S & F in repairs 20mm dia brass chromium plated tubular towel rail complete.

S & F for mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete confirming to grade Fe 410-W (Gde- E- 250) quality-A, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M & L in repair for mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework (caging) of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed

M & L for preparing new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

M & L for preparing new steel surface of any description not otherwise described n. exc. 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

M & L for preparing new wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land all as directed by Engr-in-Charge.

S & F 20 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

Taking up or down 25mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land all as directed by Engr-in-Charge.

S & F 25mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors all as directed.

S & F in repairs 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S & F in repairs 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S & F 110mm bore PVC (SWR) bends any radius all as specified and as directed.

S & F 110mm bore PVC (SWR) bends any radius with oval access doors all as specified and as directed.

S & F in repairs 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S & F 75mm bore PVC (SWR) bends any radius all as specified and as directed.

S & F 75mm bore PVC (SWR) bends any radius with oval access doors all as specified and as directed.

S & F in repair 75mm PVC (SWR) floor trap, including jointing with solvent all as specified and as directed.

S&F in repairs grating 150mmx150mm made out of stainless steel complete all as specified and directed.

S & F 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches with access door all as specified and as directed

S & F 75mm bore PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches with access door all as specified and as directed

S & F stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 110mm bore pipe all as specified and as directed

S & F stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 75mm bore pipe all as specified and as directed

S & F 110mm PVC (SWR) vent cowl all as specified and as directed

S & F 75mm PVC (SWR) vent cowl all as specified and as directed

S & F in repairs 15mm bore chromium plated fancy type bib tap long body, screwed down, high pressure for iron pipe or for brass ferrule

S & F in repair CP wall mixer three in one system for mixing hot and cold water screwed down for iron pipe 15 mm bore and fixed complete all as specified and directed. Make Prayag or equivelent make.

S & F in repairs stop valves/Angle valve15mm bore fancy type chromium plated screwed both ends for iron pipe or for unions and fixed

S & F in repairs 25mm dia bore gun-metal, globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed

S & F in repairs 125mm dia chromium plated shower rose with swivel joints including fixing to steel pipe or GI union complete

S&F 32 mm bore low density polyethylene pipe (LDPE) of pressure rating 6 Kgf/cm2 as in waste pipe

Dismantling of water storage tank of 500 ltrs capacity.

S & F 1000 Ltrs Rotational moulded polyethylene water storage tanks triple layered (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-l

S & F in repairs 25mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 455gms) complete all as specified and as directed.

S&F in repair Vitreous China wash down water closet pan (Europion pattern), white (excluding fixing bolts, flushing cistern and flush pipe) squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor. complete all as specified and as directed.

S&F in repairs Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs PVC flushing cistren low level, 10 ltr capacity with syphonic action type ball valve. Incl inlet ball valve, PVC band (flush pipe) 32mm complete all as specified.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S & F 110mm PVC (SWR) WC connector with lip ring all as specified and as directed.

S & F 110mm PVC (SWR) WC connector bent type to fit WC outlet all as specified and as directed.

S&F in repair vitreous china Wash hand basin, white , flat back size 550x400 mm except taps, CP waste coupling but incl brackets all as specified. Make cera/Hindware

S&F in repair brass CP centre hole basin mixer for mixing hot & cold water three way screwed down for iron pipe 15mm bore and fixed complete.

S & F 32 mm dia stainless steel waste coupling for wash hand basin all as specified and directed. Make : Prayag or equivalant.

S & F in repair PVC connections 15mm size with PTMT nuts of length 450mm

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever bracket and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified.

Supply & Fix in repairs stainless steel wall mounted plate rack of size 880x880X 220 mm and thickness of sheet not less than 0.50mm with provn for keeping plates and other crockery fixed with screw and rawal plug etc on wall complete all as specified and as directed

S& F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F 40mm bore UPVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe

Demolition of reinforced cement concrete as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work

M&L Cement concrete type B1 1:2:4 (20 mm graded aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges.

M&L for complete removal of existing treatment from walls and applying two coats of distemper oil emulsion, white or tinted, over and including of 3mm thick Birla/JK wall care putty over a coat of primer all as directed.

M&L for complete removal of existing treatment from ceiling and applying two coats of distemper oil emulsion, white or tinted, over and including of 3mm thick Birla/JK wall care putty over a coat of primer all as directed.

Taking down cement plaster on brick/concrete surface including racking out joints hacking for key scrubbing down with water etc.

Demolition brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars, etc,

M&L Brickwork with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in CM 1:6

M & L Rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement)

M&L Rendering 5 mm thick on fair faces of brick work or concrete sur-faces of ceiling in cement mortar 1:3 for finished even and smooth (without using extra cement)

M & L for preparing new plastered surfaces of wall and applying two coats of oil bound distemper over and including a coat of 2mm average thickness birla/ equivalent wall care putty and one coat of primer all as specified and as directed.

M & L for preparing new plastered surfaces of ceiling and applying two coats of oil bound distemper over and including a coat of 2mm average thickness birla/ equivalent wall care putty and one coat of primer all as specified and as directed.

M & L for complete removal of loose / cracked concrete incl reinforcement if required, from RCC roof projection,chajja,fins,facia, roof bands etc and making good with PCC (1:11/2; :3) type A0 (using 12.5 mm graded stone aggregate) in any slab and in any position finished the surface even and smooth with out using extra cement including necessary form work and welding/binding of reinforcement (including reinforcement) if required complete and applying three coat of white wash/two coat of cement base paint to match with the existing surface as directed by the Engr- in -Charge . (Reiforcement will be measured and paid saperately under respective item.

M&L for Providing reinforced cement concrete (nominal mix) Type B1, 1:2::4 (using 20 mm Aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary form work complete all as specified and directed. Note. (reinforcement shall be measured and paid separately)

M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specifed and as directed.

Complete removal of existing water proofing treatment including plaster and concrete padding, roughening of concrete surface, cleaning and washing down the surface with water and removing debris/rubbish out side MD land complete all as specified and directed by Engr-In-Charge

M&L for water Proofing treatment to roof slabs by applying one coat of bituminous/polymerized primer confirming to IS-3384 @ 0.40 Ltrs/Sqm, and laying atactic polypropylene (APP) modified membrane pre fabricated , reinforced with non woven polyester, of minimuum 3 Kg/Sqm, 3 mm thick (minimum) with minimum 75 mm side overlaps and minium 100 mm end overlaps and applying one coat of aluminium paint @ 0.11 Kg/Sqm over APP membrane complete all as specified and directed by Engr-In-Charge

M & L for brushing with neat cement slurry @ 3Kg/Sqm

M&L for 100 mm thick PCC 1:4:8 mix ,type D-2, using 40 mm graded stone aggregate as in tank staging complete all as specified & directed.

M&L for 100 mm thick PCC 1:2:4 mix ,type B-2, using 40 mm graded stone aggregate as in tank staging complete all as specified & directed.

M&L for Treatment of roof cracks in existing roof surface by cutting out portion along the cracks with mechanical equipment into 'V' shape, cleaning the cut out portion with compressed air to remove all foreign materials like dust, dirt, aggregates etc., apply the crack seal compound over existing cracks of roof as per manufacturer instructions or all as specified entire satisfication of GE/Engineer-in-Charge. Make: FOSROC/Dr Fixit/Pidilite

Demolition of existing PCC/lean concrete including floor tiles and removing rubbish off the premises.

M&L for providing & laying applying one coat of bituminious/polymerized primer confirming to IS-3384 @ 0.40 Ltrs/Sqm, 3 mm thick APP modified polymeric membrane of weight of 3 kg/sqm with non-woven polyester reinforcement shall be laid over a coat of bitumen S-35 grade (30/40) applied @1.20Kg /Sqm (minimum) with minimum 75 mm side overlaps and minimum 100 mm end overlaps, joints & overlaps shall be sealed as per manufacturer instructions complete all as specified and as directed.

M&L for sunken portion filled with lean concrete 1:5:10 using brick/lime aggregate and finish the surfaces rough to receive sub base complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc.15 cm thickness (below or above ground level) and removing from site all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 mix type C2 using 40mm graded stone aggregate as in paving finishing cone surface (plinth protection) even and smooth without using extra cement.

M&L for factory made precast machine pressed kerb stones of PCC grade M-15 design mix and of shape and size rected, set jointed and pointed cement and sand mortar 1:4 fixed in repairs with and including necessary excavation and earthwork and making good the disturbed surfaces to match with the existing surfaces including removal of dispodal of rubbish complete all as specified and directed. Sizes shall be as under :- Length (L) not less than 300mm, Height (H) 300mm to 350mm, Thickness (T) 100mm and radius (R) 75mm including painting on kerb stone of synthetic enamel paint yellow or white colour complete all as specified and directed.

M & L Hard core gauge not exc. 63mm of broken bricks diposited spread and levelled in layers not exc. 15 cm watered and rammed to a true surface complete all as specified.

M&L Sand Filling a layer of 50mm thick sand cushioning including filling the joints with sand as in floors/ paths including watering and consolidation complete all as specified and directed.

Material and labour for 60 mm thick, machine made ,1st quality, precast cement concrete rubber moulded coloured interlocking paver blocks , of triangular / Zigzag / Haxagone/ I , in shape or shap and design as approved, with grey cement and pigment , having M-35 Grade and conforming to IS 15658-2006 specifications , complete all as specified and directed.

Taking down carefully existing unserviceable copper/aluminium point wiring (light, fan, socket or power point etc) complete with fittings/fixures such as switches sockets, ceiling rose, fan regulators, etc ( except tube light fittings), removing materials for taking credit and making good disturbed surface of wall, floors, etc complete all as directed by Eng-in-Charge.

Taking down main switch, DB/change over/VTPN, MCCB AC box of any capacity.

M & L Point wiring complete with 1.5 sqmm single core PVC insulated (FRLS) and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC Conduit and all accessories Concealed in walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover for housing the switches, socket outlets, fan regulators etc complete including cutting of chases where as required and making good all disturbed work to match the existing all as specified and as directed for the following:-

One light point controlled by one switch.

One ceiling fan point controlled by one switch and fan regulator.

One exhaust fan point controlled by one switch.

One bell point controlled by one bell push

One 3 pin socket outlet 5 Amps independent board.

One 3 pin socket outlet 5 Amps on the same board with other switch.

One light point controlled by two Nos two way switches

All as per item No. 122 here-inbefore but with 2.5 sqmm PVC insulated multistranded flexible unsheathed copper conductor inclusive of 2.5 sqmm PVC insulated multistranded flexible copper conductor for one independent 6 pin 16 Amp socket.

S&F Modular switch, one way, 6 Amp 230, 1 module all as specified and directed by Engr in charge.

S&F Modular switch, two way, 6 Amp 230, 1 module.all as specified and directed by Engr in charge.

S&F switch Modular, single pole, one way,16 Amp ,1 module 230 Volt

S&F socket modular 6/16 Amp, 2/3 pin combined ,2 module 230 Volt .

S&F socket Modular 6 Amp-2/3 pin combined 2 module

S & F ceiling rose surface polycarbonate body three terminal.

S&F Modular lamp holder Polycarbonate type with back plate suitable for Batten fitting Suitable for B22 type bulb.

S&F modular fan step regulator 120W 2 module.

S&F modular bell push 6A ,1 module

S&F call bell ding dong 230 Volt , single phase.

S & F of BLDC White colour ceiling fan complete with blades and antisuside rod from existing roof / trus to fall ceiling, and accessories, 230V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE,Winding material 100 % copper ,350RPM air velocity 215m3/min,anti rust blades five star rated with brushless direct current motor including ceiling fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and taking down existing UNSV ceiling fan complete all as specified and directed. Note : 1) Old ceiling fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. 2). 02 years guarantee to be provided by the contractor.

Supply and fix electric water heater, storage type, steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc including disconnecting & taking down existing geyser complete all as specified and directed Note : 1) Old unserviceable water heater shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. complete all as specified and directed 2. Making suitable size of hole on wall for fixing the exhaust fan .3. 02 years guarantee to be provided by the contractor.

Supply and fix of LED light fitting 1X20Watt, 220 Volt AC , input voltage 140-270 V AC,CCT 6500K, Lumin efficency 100 lm/watt ,surge protection upto 4KV , Voltage protection upto 440 V AC.PF >0.9, decorative box type with drivers, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete including taking down old unserviceable existing light fitting complete all as specified and directed. Note : Warrenty on light should be of minimum 02 Years.

Supply and fixing LED light fitting made of Aluminium extrusion mirror type with high out put diffuser 1x10 watt 2 feet , input voltage 140-270 V AC,CCT 6500K, Lumin efficency 100 lm/watt ,surge protection upto 4KV , Voltage protection upto 440 V AC.PF >0.9 with driver including connecting up with flexible copper conductor cable of suitable size from ceiling rose complete including taking down old unserviceable existing light fitting complete all as specified and directed by Engr in charge. Note : Warrenty on light should be of minimum 02 Years.

S&F LED bulb B22 9 watt inverter bulb ,lumin efficency 900 lumin/watt in normal mode and 350 lumin/watt in power backup mode,CRI ≥80,CCT-6500K ,surge protection upto 4KV,Voltage Protection upto 400 volt,PF ≥ 0.9 suitable for batten holder fitting complete all as specified and directed by Engr in charge. Note Warrenty on light should be of minimum 02 Years.

Taking down and refixing connecting same electric meter SP up to 60 amp incl S & F suitable new board close recessed type of suitable size and making good to disturbed surface and matching with the existing colour of wall. All as specified and directed by engr in charge.

S & F of exhaust fan of white colour made of sturdy engineering PVC complete with louvers shutter, voltage 230V, 50Hz, RPM 1200, noise level 40-45dB ,water resistant ,copper winding of sweep 250mm including exhaust fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and taking down existing UNSV exhaust fan complete all as specified and directed. Note : 1) Old unserviceable Exhaust fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. complete all as specified and directed 2. Making suitable size of hole on wall for fixing the exhaust fan .3. 02 years guarantee to be provided by the contractor.

S & F of exhaust fan made of sturdy engineering steel body complete net mosquito with louvers shutter, voltage 230V, 50Hz, RPM 1400 ,70 watt, noise level 40-45dB area dynamically designed & balanced blade,4 nos blade, Air flow capacity 1850m3/hrCMPH, copper winding of sweep 300mm including exhaust fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and taking down existing UNSV exhaust fan complete all as specified and directed. Note : 1) Old unserviceable Exhaust fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. 2. Making suitable size of hole on wall for fixing the exhaust fan .3. 02 years guarantee to be provided by the contractor.

S&F Modular AC box metal enclosure with socket plug top and MCB SP 25 Amps flush mounting enclosure (01 No) complete all as directed by Engineer-in-Charge

Sub main wiring with FRLS two single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 4.0 Sqmm size drawn through and including not less than 25 mm dia PVC conduit medium grade ISI marked and conduit junction boxes, terminal boxes and accessories such as tees, bends, elbows, reducers, bell mouth tube ends fixed to the surface of wall/ceiling including one run of 4.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor. Note : Two runs of single core 4.0 sqmm and one run of 4.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length.

S&F double door metallic sheet metal enclosure DB double door VTPN suitable for housing 125 MCCB as incomer 4 Way 415 Volts with 160 Amps rated bus bars.

S & F sheet metal enclosures (double door) for DBs where MCBs to be used single pole and neutral 8 way 240 V with 200 amps rated bus bar fixed on wall complete with all acessories including taking down old unserviceable MCB DB with MCBs complete all as specified and directed

S & F MCB single pole, having rupturing 10KA, 6 amps to 32 amps as ordered 240 Volts

S & F MCB Single pole and neutral (SPN), having rupturing 10KA, 240 V 63 amps as ordered.

S&F testing and commissioning of MCB TPN 63 A ,415 volt 50 Hz,10ka in accordance with IEC 60947- 2 having C-curve characteristics connected with suitable lugs.All as specified and directed by Engr-in charge

S & F MCCB 125 Amp , 10KA, 240/415 V four pole all as specified and directed by Engr-in charge

S & F of Inverter LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection,inbuilt battery Back-up auto ON/OFF/Dimmer(Pre-programable), including bracket made out of GI pipe light grade 32mm bore not less than 1.20m long bent to shape required fixed to pole with suitable size 2 Nos clamps made out of 25X3mm flat iron with nut, bolts and washers complete complete all as specified and directed Note : Warrenty on light should be of minimum 02 Years.

Taking down existing earthing and M & L Earthing complete with galvanised steel earth plate electrode, 60x60cmx 6.3mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level,connected to galvanised earth lead wire 4.0mm dia by means of bolts,nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion Note :- (i) The rate quoted shall also deemed to include the cost of GI wire and protection pipe upto 7.5 Mtr beyond the earth plates electrode and also the cost of the Test point. (ii) Joining of GI earth wire with pipe of the test point shall be done by using suitable cable lugs.

Please Enable Macros to View BoQ information