PROVISION OF COVERED WEATHER PROOF SHED REAR STAIR CASE BLDG NO P203 SHILPIKA AT NAVAL PARK NORA AS AND AS TO BLDG NO P192 AT NORA AND EAST SIDE WALL OF AMZARI PARK AT NORA SPECIAL REPAIRS TO GAS STORE HOUSES AT BLDG NO P-20A DEMOLITION AND CONSTRU

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil all as specified and directed

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, trenches for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

Ditto all as per serial item No.2.00 but exceeding 1.5 M and n.exc 3.0 M depth

Excavation in post hole each not exc 0.5 Cum getting out returning, filling in and ramming earth or broken rubble mixed into earth around in layers n.exc 25 cm watering and removing surplus soil to a distance n.exc 50 m and making surfaces good in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, watering and well ramming in layers not exceeding 25cm thick with soils complete all as specified and as directed.

Removing excavated spoil to a distance exceeding 1.50KM but not exceeding 5.0KM and depositing where directed at a level n. exc 1.5 m above the starting point all as specified and directed.

Removing building materials (other spoil payble under earth work and rate shall apply only where removing of etc is not other wise provided for or consider in Schedule of credit ) to distance exceeding 1.50 Km but not exceeding 5 Km including loading, unloading and stacking at the destination complete all as specified and directed. Note: One metric tonne shall mean one load .

PCC 1:4:8 type D-2 (40mm graded aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

PCC 1:2:4 type B-1 (20mm graded aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

Reinforced Cement Concrete 1:2:4 type B1 using 20 mm aggregates for foundations including rafts, footings and mass concrete, beams; plinth beams; bases for columns, etc.; basement slabs, complete all as specified and as directed.

Reinforced Cement Concrete 1:2:4 type B1 using 20 mm aggregates for columns, pillars, piers, posts and struts and the like complete all as specified and as directed.

Reinforced Cement Concrete 1:2:4 type B1 using 20 mm aggregates for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Use and waste of form work to sides of concrete foundations , footings,bases of columns,raft and raft beams,sides and soffits (if any) of foundation and plinth beams,and similar work,vertical or to batter for rough finished surfaces complete.

Use and waste of form work to sides of pillars,post struts,piers columns and stanchions of square or rectangular shape in rough finished surfaces of concrete complete ete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc for rough finished surfaces of concrete complete ete all as specified and directed.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs not exceeding 200 mm thick complete all as specified and directed.

Mild Steel high strength Corrosion resistant TMT deformed bars of grade Fe-500D of bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

Mild Steel high strength corrosion resistant TMT deformed bars of grade Fe-500D of bars 5mm dia and over upto and including 10mm dia stirrups ,spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and as directed.

Brickwork with fly ash bricks in half brick thick straight or curved on plan exceeding 6m mean radius and built in cement mortar 1:4 all as specified and as directed.

Walling of Random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.

Rendering to brick / concrete ceiling surfaces, 5 mm thick in Cement Mortar 1:3, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 10 mm thick in cement mortar 1:6 on fair face of brick work or concrete surface for finished even and smooth with out using extra cement all as specified.

10mm thick rendering in CM (1:4) on concrete surfaces using water proofing compound @2% by weight of cement and finishing the surface even and fair complete all as specified and as directed. Note: WPC shall be measured and paid seperately.

Rendering 15mm thick on concrete / brick surface in two coats, first coat 10mm thick in CM ( 1:6) and 2nd coat 5mm thick in CM (1:4) finished even and smooth without using extra cement, 2nd coat mixed with water proofing compound @2% by weight of cement all as specified and directed. Note: Water proofing compound will measued and paid separately.

Supply only integral water proofing compound conforming IS 2645-1975 of approved make. Make : Acco proof / Impermo / Lik proof / Scott No. 1

APP polymeric waterproofing membrane of 3 Kg / Sq.M incorporating a centre core of 90 micron thick HMHDPE film including coating the surface with a coat of water based bitumenous Primer @ 100 gms / Sqm, followed by a coat of blown bitumen of grade 85 / 25 or 90 / 15 @ 1.2 Kg / Sqm each at top and bottom of the membrane complete including sealing all joints by thermo fusion with minimum 10cm overlap and finished with a coat of bituminous aluminum paint @ 100 grams per Sq.m on top for water proofing treatment complete as per manufacturer's instructions all as specified and as directed. Make : Multiplas by STP Texas Limited, Gurgoan / STP Superior Poly Plus by STP Limited, Calcutta / Shivam Tar Products / Jalnidhi Bitumen Specalities Pvt Ltd / Texsa India Ltd, Gurgaon / Tiki Tar Danosa [India] Ltd( Hydrostop) Gujarat.

Hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

100 mm thick Cement concrete type D2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing complete all as specified and as directed.

Ditto all as per serial item No.30.00 but 75 mm thick

75 mm thick plain cement concrete type B1,1:2:4 using 20mm graded stone aggregate for flooring finished even and smooth without using extra cement and spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and as directed.

38 mm width of aluminium dividing strips,1.5mm thick and inserted in top surface as in a pattern of grid conform to design complete all as specified and directed.

PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in plinth protection 50 mm thick complete all as specified and as directed.

Bitumastic gola, with 80/25 bitumen and coarse sand mixture. 1:3 by weight, 8cmx8cm at the junction of plinth protection complete all as specified and as directed.

Sand cushioning 50mm thick under interlocking paver tiles including watering and consolidation complete all as specified and directed.

Machine pressed precast concrete coloured/multicoloured interlocking paverblock with glossy finish any shape and size confirming to IS-15658 of 2006 of 60mm thickness,M-35 grade with grey cement and pigment complete all as specified and directed. Make: A-one tile/ Bansal /wonder crete/ Bharat pavers / NITCO/ Ultra Tiles Pvt Ltd / Mehtab Tiles

Cutting holes into or through brick work/RCC wall built in cement mortar for fixing hold fasts and making good dismantled portion in CM(1:3) or in cement concrete 1:2:4 type B-1 , sperficial area not exceeding 400 Sqcm but 0.1 Sqm all as specified and directed.

Cutting holes into or through cement concrete slabs, chajjas, etc ., reinforced or otherwise, area exceeding 100 Sqcm and not exceeding 250 Sqcm all as specified and directed.

Preparation of new steel surfaces of any description , over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. Make :M/s. Asian Paints [Apcolite], M/s. Berger Paints [Luxol], Jenson & Nicholson [Brolac] all are 1st quality.

Preparation of new or previously untreated surfaces , Surfaces plain or moulded, n exc 10cm width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over priming tack coat primer complete all as specified and as directed. Make :M/s. Asian Paints [Apcolite], M/s. Berger Paints [Luxol], Jenson & Nicholson [Brolac] all are 1st quality.

10 mm thick anti skid vitrified parking/paver tiles area of each tile not exceeding 0.36 Sqm, terracotta/Ivory series, set, jointed and pointed in neat white or colour cement slurry to match the colour of tiles as in floors over including 20 mm thick screed bed or bedding layer (CM 1:6) , colour and design of tiles shall be as approved by Accepting Officer complete all as specified and as directed. Make: Kajaria Ceramics Ltd / Asian Granito India Ltd / Somany Ceramics Limited / Varmora Granito Pvt Ltd / H & R Johnson India Ltd / Nitco / Orient Bell Ltd/ Oasis Vitrified Pvt Ltd (Premium Quality)

Vitrified Ceramic tiles light shade 10 mm thick (square / rectangular) polished, area of each tile not exceeding 0.36 sqm, as in floors etc laid over and including 15 mm thick screed bed in CM(1:6) set & jointed in neat cement slurry & pointed in white or coloured cement to match complete all as specified and as directed. Make:- Kajaria Ceramics Ltd / Asian Granito India Ltd / Somany Ceramics Limited / Varmora Granito Pvt Ltd / H & R Johnson India Ltd / Nitco / Orient Bell Ltd/ Oasis Vitrified Pvt Ltd (Premium Quality)

18 to 20 mm thick Machine cut Kota stone slab as in flooring laid over including 20 mm thick cement screed bed in CM (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

18 to 20 mm thick Granite (of any type) work (table rubbed and polished) for skirtings/jambs/dados/wall lining (veneering to wall) and like laid on including 10mm thick in cement mortar (1:3) bacing coat and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

18 to 20 mm thick machine cut Kota stone slab as in riser of steps, skirting, dado and pillar laid over including cement backing coat of 10mm thick in CM (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Providing Cement Concrete Type B-1, 1:2:4 using 20mm graded aggregates in lintels upto 1.5m clear span, cills, steps; sesmic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in (SSR) Item 4028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, necessary form work complete all as specified and as directed.

Preparing new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed. Make : Birla Laval Plast / Berger / J & N / Shalimar Paints / Asian Paints

Ditto all as per serial item No.48 but in ceilings

Preparing old surfaces of walls by brooming down or by steel wire brushing and applying one coat of white wash complete all as specified and as directed.

Preparing old surfaces of walls by brooming down or by steel wire brushing and applying one coat of oil bound distemper all as specified and directed Make: Berger [Jadoo] / Nerolac / British Paint / Jotun India Pvt Ltd / Velvet Acrylic Distemper [Crimson Paints Pvt Ltd.] /Asian ( All 1st quality)

Preparation of new plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistent primer complete all as specified. Make: Snowcem Plus / Berger / Asian Paints [Gutucam] / Jotun India Pvt Ltd / Crimocem Super Cement Paints

Preparing old surfaces of walls by brooming down or by steel wire brushing and applying one coat of cement based paint complete all as specified and as directed.

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

steel ventilators with centre hung shutter including hinges, steel peg stay, complete all as specified.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel wire staples complete all as specified and directed.

3 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm in each pane complete all as specified. Make:Saint Gobain Glass / Modiguard Float Glass / Asahi India / Hindustan

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, pillars etc., and disposal off unserviceable materials, debris to out side MD land complete all as specified and as directed.

Demolition of Plain Cement Concrete of any description and in any position not otherwise specifically provided and removing rubbish to out side MD land work complete all as specified and as directed.

Demolition of Reinforced cement concrete (reinforcement cut as required to facilitate demolition) in any roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed.

Plain Cement Concrete 1:2:4, Type B-1, using 20mm graded aggregate as in Sub base / levelling course 40 mm thick, for flooring complete all as specified and as directed.

Dismantling Structural steel work including doors, gates but excluding framed truss etc.complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for any position or any type or any floor complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge and thickness from roof coverings including ridges, hips, valleys and flashings or similar pattern complete all as specified and directed

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish to outside the premises, and depositing serviceable materials where directed and leaving the work site clear of any plastering complete all as specified and as directed.

Pre-Painted Galvalume aluminum zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self-tapping screws complete all as specified and directed. MAKE : Tata Blue Scope / Saxena Marine Tech Pvt Ltd/ Build Tech / Jindal

Pre-Painted Galvalume aluminum zinc coating GI based plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self-tapping screws as specified and as directed. MAKE : Tata Blue Scope / Saxena Marine Tech Pvt Ltd/ Build Tech / Jindal

In repairs, 10 mm thick Seamless calcium silicate false ceiling made out of1800 x 1200mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having phillips head with under head cutter at 200mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48mm wide fibre tape to provide seamless finish all as recommended by manufacturer and applying two or more coats of cement based wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on surfaces and applying two coats of acrylic washable distemper over a coat of alkali resistant primer and including frame work using GI perimeter channels of 0.55 mm thick, having one flange of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, fixed to wall with nylon sleeves and screws at 450 mm intervals. GI intermediate channels of size 45X15X0.9 mm supported with GI ceiling angles of size 25X10X0.5 mm fixed to soffits with steel expansion fasterners/GI cleats at 1220 mm intervals, ceiling sections of 0.5 mm thick having knurled web of 51.5 mm and two flanges of 26 mm each with lips of 10.5 mm fixed to intermediate channel with connecting clips and in direction perpendicular to the intermediate channels at 457 mm centre to centre all as recommended by manufacturer complete all as specified and as directed.

Note:- Only calcium silicate false ceiling area will be measured form wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm the calcium silicate ceiling tiles shall have NRC value of 0.50 (Minimum), light reflection >85%, non combustile as per B S 476 part 4, 100% humidity resistance and also having thermal conductivity <0.043 W/MK. Make :Armstrong / India Gypsum / Lafarge / Gypstone / Saint Gobain / Everest

Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe 410-W Gde E-250 quality A complete all as specified and as directed.

MS hand rails, half round or other steel section or core for wooden hand-rail straight portion,drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut with diameter of shank 5 to 10 mm, but length of bolt n.exc 5cm long complete all as specified and as directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut with diameter of shank 16 to 20 mm, but length of bolt exc. 15 cm but n.exc 22.5cm long complete all as specified and as directed.

Rolled Mild Steel sections as in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161- 1979 grade St.-240 complete all as specified and directed.

Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410-W (Gde-E- 250) quality-A complete all as specified and directed.

Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410-W (Gde-E- 250) quality-A complete all as specified and directed.

Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410-W (Gde-E- 250) quality-B complete all as specified and directed.

Mild Steel Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors, and gates; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165 including spikes or flowers or any other onamental piece works of any number and necessary welding or fixing with screws etc as directed

Rolled Mild Steel sections in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe 410-W (Gde-E- 250) quality-B complete all as specified and directed.

Expanded metal, not exceeding 4 Kg per squaremetre, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples , complete to wood or steel members all as specified and directed.

Mild steel, plain, black sheet, 1.25 mm thick, in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required all as specified and directed.

Dismantling of wall and ceiling boards (fibre pulp,insulation etc) or insulation boards/slabs any thickness including cover fillets complete all as specified and as directed.

18/19 mm thick plywood, grade BWR (Marine) type BB, fixed with screws to timber frame work, termite proof complete all as specified and as directed. Make: Greenply Industries [Ply & Board Division] / Kitply / Century / National Plywood Industries Pvt. Ltd. / Archid Ply/ Sylvan Ply

0.9 mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with mechine or heat pressed by approved adhesive as per manufacturer's instructions complete all as specified and as directed.

Stainless steek basket of size 475mmX500mmX 100mm with Ext. width 475mm as in kitchen drawers modular type made out of stainless steel 4mm dia wire at 30mm c/c and fixed to 18 mm thick BWR grade plywood covered with 0.9mm thick decorative laminate of approved shade fixed on both sides with all fixing accessories confirmed to relevant IS complete all as shown & specified on Drawings in serial page No. 107 to 113 of tender documents all as per manufacture specification complete all as specified and as directed and as shown on drawing of the foollowing items: Cuttlery basket, Cup and saucer etc.

Stainless steek basket of size 475mmX500mmX 200mm with Ext. width 475mm as in kitchen drawers modular type made out of stainless steel 4mm dia wire at 30mm c/c and fixed to 18 mm thick BWR grade plywood covered with 0.9mm thick decorative laminate of approved shade fixed on both sides with all fixing accessories confirmed to relevant IS complete all as shown & specified on Drawings in serial page No. 107 to 113 of tender documents all as per manufacture specification complete all as specified and as directed and as shown on drawing of the foollowing items: Thali basket, Plain wire basket etc.

Stainless steel (Manual Type) Sliding/Telescopic channel of length 20" (500 mm) with 3nos of holding ball of load carring capacity 45-50 Kg of 202 grade steel of total width 45 mm including nenecessary fitting arrangements on drawers complete all as specified and as directed.

Cold rolled nickel plated steel 'O' cranck soft closeing concealed hinges (15-22mm) including nenecessary fitting arrangements on shutters complete all as specified and as directed.

Stainless steel 100mmX100mm ventilator for cupboard shutter with nenecessary fitting arrangements complete all as specified and as directed.

Stainless steel modular kitchen handles 100mm long with nenecessary fitting arrangements complete all as specified and as directed. Note for serial item No. 84 to 89:- (i) Contractor shall executed the work all as directed by Engineer-in-Charge. (ii) Any minor changes required shall be deemed to be include in the rate quoted by contractor. (iii) The colour of marine ply/madular kitchen shall be as approved by GE. Make: Godrej Interio / Harshita Enterprises/ Kumar Modular kitchen / Mahesh interiors

E/M PORTION

Point wiring with two runs of single core 4.0 Sq.mm. (Nominal area) PVC insulated unsheathed multistranded copper conductor cable FRLS (ISI marked) drawn through and including non metallic PVC conduit 20 mm bore medium grade (ISI marked) concealed / surface fitted type including Flush type metal GI boxes for fixing modular type / MS sunken box for conventional type switches, sockets, regulators etc. for one 15 Amps, Exhaust fan / wall mounted/geyser/AC/ Water cooler point including 4 Sq mm FRLS copper conductor cable for earth continuity conductor and connecting it to earth dolly on independent board complete all as specified and as directed Make of Cable : Finolex, Polycab, Plaza, Gloster, Harsh all are ISI marked and FRLS cables Make of Conduit : Avon Plast,Precision, Finolex all are ISI marked.

In repairs, Sub main wiring with 4 runs of 6 Sqmm PVC insulated FRLS Copper conductor cable in including PVC conduit 25 mm dia along with one run of 6.0 Sq.mm FRLS copper cable for earth continuity conductor as earth lead and connecting to common earth dolly including complete all as specified and as directed. Note: Four runs 6 Sq.mm. cable, one run of 6 Sq.mm cable and one run of PVC conduit will be measured as one unit. Make :(i) CABLE : Finolex, Polycab, Plaza, Gloster, Harsh all are ISI marked and FRLS cables (ii) Make of Conduit : Avon Plast,Precision, Finolex all are ISI marked.

In repairs, Sub main wiring with 2 runs of 4 Sqmm PVC insulated FRLS Copper conductor cable in including PVC conduit 25 mm dia along with one run of 4.0 Sq.mm FRLS copper cable for earth continuity conductor as earth lead and connecting to common earth dolly including complete all as specified and as directed. Note: Two runs 4 Sq.mm. cable, one run of 4 Sq.mm cable and one run of PVC conduit will be measured as one unit. Make :(i) CABLE : Finolex, Polycab, Plaza, Gloster, Harsh all are ISI marked and FRLS cables (ii) Make of Conduit : Avon Plast,Precision, Finolex all are ISI marked.

Distribution Board, VTPN 4 Way ,Double door 240V and having provision for TP MCCB up to 125 Amps in 16 KA, 25 KA (Frame 1) as incomer complete all as specified and as directed. Make : Indo Asian cat part No. NVMCB04 / Standard / Havells

MCCB, 3 pole 63 Amps 50 HZ 415 with rupturing capacity 16 KA complete all as specified and as directed. Make: Indo Asian Cat part No. 83006 / Legrand / L & T / Siemens / ABB / C & S / Schneider / GE

MCB SPN 6 to 32 Amps 240 Volts C curve, 10 KA complete all as specified and as directed. Make: Indo Asian Cat part No. 811152 / Legrand / L & T [Hager] / Siemens / ABB / Schneider / GE / C & S

MCB SP 6 to 32 Amps, 240 Volts, C curve, complete all as specified and as directed. Make: Indo Asian Cat part No. 811122 to 811129 / Legrand / L & T [Hager] / Siemens / ABB / Schneider / GE / C & S

Sheet metal enclouser single pole and neutral enclosure with two pin and earth plug and socket complete with one single pole MCB 20 amps capacity complete all as specified and as directed. Make : INDO ASIAN / STANDARD / HAVELLS

Switch Modular type single pole 16 Amps One Way AC 230V, 50HZ supply 1 module complete all as specified and as directed. Make : Legrand / Crabtree / Anchor (Roma) / MK

Modular type switch socket 6 A/ 16A 2/3 Pin Combined multi purpose AC 230V, 50HZ complete all as specified and as directed. Make : Legrand / Crabtree / Anchor (Roma) / MKMake: MK / Legrand / ROMA / ABB

Modular white cover plate with frame 3 module complete all as specified and as directed. Make : Legrand / Crabtree / Anchor (Roma) / MK

Exhaust fan 600 mm sweep or nearest size, metal body (Heavy duty), complete with louvers suitable for operation on 230 V AC, 50 Hz AC including making suitable size of opening in wall for fixing and making good the distrubered surfaces etc complete all as specified and as directed Make : Havells/Bajaj/CG/Orient

Air circulator fan 600 mm sweep or nearest size, complete suitable for operation on 230 V AC, 50 Hz AC single phase, oscillating suitable for wall mounting including all accessories complete all as specified and as directed Make : Havells/Bajaj/CG/Orient

Supply , Install, testing and commissioning of hi wall split units BEE 5 star rated air-conditioner indoor / out door complete with cord less remote control unit and with in built air ioniser and plasma filter for better indoor air quality with latest inverter technology having ECO friendly Refrigerent gas, copper condensor coil and EER 3.2 of capacity 2 TR including necessary brackets (where ever required) complete all as specified and directed. Make:- Blue Star/ Hitachi/ Carriers

Voltage stablizer for automatic operation, single phase naturally air cold indoor type and designed input variation between 170 volt to 250 volt with out put voltage stablised at 230 volt with accuracy of +/-2.5% and of capacity 5 KVA. Make :Voltamp / APLAB / Andrew Yule / Brentford / AE / Vintec [Volina]

Earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to GI wire 4mm dia (up to 7.5 m in length from earth plate) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no.3 of SSR part I including Charcoal and rock salt with necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia 150mm long reinforcement, watering funnel, 40 mm dia light grade for protection of earth electrode 20 mm dia for watering and pouring extra Clay Soil of qty not less than one cubic meter into the earth pit and also removal of excavated soil not less than 50 mtr from the earthing place all as specified and directed by E-in-Charge complete all as specified and as directed.

VIJAY VINAYAKA INFRA

P SRINIVASA RAO