DMF Grant

Centering and scaffolding charges for RCC members including all materials and labour charges for forming and Dismantling for DOME Lab -00667 for Ring beam

M30 Grade using 20 mm HBG M/C metal including cost and conveyance of all materials and labour charges including centering, curing, machine mixing, vibrating charges etc., complete., but excluding cost of steel and its fabrication charges etc., complete., for Dome Slab

M30 Grade using 20 mm HBG M/C metal including cost and conveyance of all materials and labour charges including centering, curing, machine mixing, vibrating charges etc., complete., but excluding cost of steel and its fabrication charges etc., complete., for Ring Beam

Accoproof Plastering with CM (1:3) 12mm thick including cost and conveyance of all materials and all labour charges, watering, curing, mixing charges etc., complete., For Side walls inside

Cement Plastering with CM (1:3) 12mm thick including cost and conveyance of all materials and all labour charges, watering, curing, mixing charges etc., complete., For sidewall inside

Painting two coats to new walls of Emulson paint including cost and conveyance of all materials and all labour charges etc., complete.,

Supplying, fitting and placing HYSD Fe 415 bar reinforcement complete as per drawings and technical specifications for bars below 36mm dia including over laps and wastage etc., complete.,

Supply and fixing of CI Light type man hole cover with frame of size 0.60x0.60 including cost and conveyance of all materials and all labour charges etc., complete.,

Placing and fixing of RCC Pre casted Ladder of 0.6 Mt width including cost and conveyance of all materials and all labour charges etc., complete.,

Drilling of 165mm dia Bore well by down the hole hammer drilling to a finished dia of 165mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation all consolidated formation etc., and drilling in over burden to dia not less than 200mm etc., and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore well at an average pressure of 150 PSI) conducting yield test, consumables charges, crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges, all taxes and EXCLUDING GST, but excluding the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS-2800 Part-I & II 1979 and amended from time to time up to 90 Mts depth.

Drilling of 165mm dia Bore well by down the hole hammer drilling to a finished dia of 165mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation all consolidated formation etc., and drilling in over burden to dia not less than 200mm etc., and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore well at an average pressure of 150 PSI) conducting yield test, consumables charges, crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges, all taxes and EXCLUDING GST, but excluding the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS-2800 Part-I & II 1979 and amended from time to time from 90 Mts to 150 Mts depth.

Drilling of 165mm dia Bore well by down the hole hammer drilling to a finished dia of 165mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation all consolidated formation etc., and drilling in over burden to dia not less than 200mm etc., and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore well at an average pressure of 150 PSI) conducting yield test, consumables charges, crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges, all taxes and EXCLUDING GST, but excluding the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS-2800 Part-I & II 1979 and amended from time to time from 150 Mts to 250 Mts depth.

Cost and supply of 180mm dia PVC Casing Pipe

Slotting chages for 180mm dia PVC Casing Pipe

Supply and fixing of 180mm dia PVC Bore Cap

Geologist charges for selection of bore well site

Supply and Transportation of 5.00HP, 12 Stage, 5star rated submersible motor pumpset, confirming to IS 8034 and motor confirming to IS 9283 with water proof winding, Pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 415V ± 10% , Three Phase 50 Hz AC supply, etc., complete for 6" Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha

Fabrication , transportation and supply of wall mounted control panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using L&T / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc., complete., for 3 phase motor pump sets. (1) Voltmeter ; 0-500 V 96x96mm size Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab - 1No (2) 0 to 20 Amps / 0- 50 Amps Ammeter 96x96mm size).Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab-1No. (3) Single phase preventor of suitable range Makes: L&T / Minilec/ Powertec. - 1No. (4) 32 A TP, 10KA MCB. Makes: Legrand / Schneider / - 1No (5) Indication lamps (R-Y-B) with switch control - 1set (6) Voltmeter & Ammeter selector switch - 2 Nos of Supply and fixing of ISI Mark suitable capacitor Makes: L&T / Siemens / Schneider / Epcos/ Havells for 7.5 HP with DOL Starter of Make C&S.Crompton / L&T / KSP/ Siemens/ BCH.

Supply and delivery of 50 mm Nominal Bore GI pipe Medium Grade properties & weight as per IS 1239 ISI mark with GI fittings including cost of pipe and its fittings etc., complete.,

Supply of 3 Core 2.50 Sqmm Flat Copper cable of ISI for Submersible Motors confirming to IS:694:1990. Makes: Finolex / RR Kabel/ Polycab / Havells / EI/ Gloster/ Goldmedal/ GM

Cost of 180mm dia PVC Bore Cap

Supply and delivery of 50mm dia PN 1.0 ( MPA) DI Double flanged slant seat seing check valve ( Non Return Valve ) with body and Disc of Ductile Iron GGG-40 / SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS 1865, IS-3896-2 with full encapsulated in vulcanized EPDM rubber and Fusion bonded ElectroStatic epoxy powder coating inside and out side color Blue RAL 5005 with Min. Coating ythickness of 250 microns. The EPDM rubber and Epoxy rubber and Epoxy Powder should conform to W 270standards (Drinking water Application) and face to face dimensions as per EN 558-1/DIN 3202-F6/IS 5312and Flange connections as per IS: 1538 excluding all duties, taxes and transportation.

Supply of 6 Sqmm WPSC (Weather Proof Twin Core) ISI Alluminium Wire. Makes: Gold Medal / Million / GM / Vimal / Finecab / Nakoda / Plaza/ Payal / Sudhakar/ Rajnigandha/ Airson/Orbit/ollvin/Beljin

Supplying and fixing of 50 mm dia MS Clamp Sets including rubber washers, bolts and nuts cost and conveyance of all materials and all labour charges etc., complete.,

Supplying and fixing of 50 mm dia GI Elbows including cost and conveyance of all materials and all labour charges etc., complete.,

Supplying and fixing of 50 mm dia MS Flang Sets including rubber washers, bolts and nuts cost and conveyance of all materials and all labour charges etc., complete.,

Labour charges for erection of 5.00 HP three phase submersible pumpsets (Bore well type) including pipe connection for suction and delivery and all labour charges etc., complete.,