SPL REPAIR TO BLDG NO P 231F TO P 233F SINGLE OFFICERS ACCN OF 18 CAVALRY AND PROVN OF BOUNDARY WALL AND FENCING AT BLDG NO NP 01 AT AHMEDABAD CANTT AND CERTAIN REVENUE WORK UNDER GE (A) AHMEDABAD

Amount

Taking down chowkats or frame with shutters ( without taking off shutters from the frame) n.exc 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 sqm each complete all as specified and directed.

S&F 30 mm thick Flush door shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 2nd hard wood factory made 35mm thick glazed, and skeleton shutters open rebated & prepared to receive, glass, gauge etc. divided into squares with plain chamfered or rounded mitred and rebated any numbers and size of members of shutters as specifed in SSR Part I, Section 8, clause 8.24(a); supllied and fitted to chowkahts complete all as specified and directed.

S&F Stainless steel butt hinges medium weight 100mm long complete all as specified and directed.

M&L for 150mm long extructed aluminium handle fabricated type complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section 150 mm size complete all as specified and directed.

S&F aluminium alloy anodised sliding door bolt with hasp and stapple ( bolt type) and fixing clips of sheet cast or extruded section with fixing bolts and sliding bolt of extruded section 300mm length & dia not less than 12mm with & including 6 Nos of bolts complete all as specified and directed.

S&F factory made solid panel PVC door, cup board shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded both side prelaminated PVC sheet PVC 'C' channel having a prelaminated PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail, lock rail & bottom rail panelling of both side prelaminated PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specification & diagram/product drawing shown on ser page No 174 of SSR Part II complete all as specified and directed & directed

S&F solid PVC door, cup board frame size 50mmx47mm made out of 5mm prelaminated PVC sheet reinforced with MS square tube all as per specification and as per drawing shown on ser page No 178 of SSR Part II (for item 08095) complete all as specified and directed and directed

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aparture 1.40mm and fixed with tinned tacks or Stainless steel wire stapples complete all as specified and directed.

M & L for providing cement concrete type C-1 1:3:6 using 20mm graded stone aggregrate in lintles up to 1.50m clear span, cills, steps, seismic and other bands, plinth courses, string courses,lacing courses, parapets and railings upto 60cm in height, copings,kneelers, apex stones, bed plates, kerbs, water trough and the like including weathering, slightly rounded or chamfered angles and throating as directed including form work complete all as specified.

Taking down steel windows and ventilators with frame (without taking off shutters) complete area not exc 1.5 sqm and removing from site of work all as directed by Engineer-in-Charge.

S&F anodised aluminum windows/ Ventilators of medium grade sections weighing 0.55 Kg/RM including necessary jointing cleats, glazing clips, rubber gasket, aluminium snap beading, screws, aluminium frame and fittings including 5 mm thick tinted sheet glass and including locking arrangements and all fittings all as per manufacturers instructions and all as specified.

S&F aluminium powder coated framed windows, any pattern, fixed/side hung/sliding Three track using powder coated aluminium sections or approved make, with or without sash bars, suitable for 5 mm thick glazing and stainless steel alloy wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm wire guaze, including necessary rubber packing, joining cleats, glazing clips, aluminium snap beading, handles, locking arrangements, frame of window should be of 1.5 mm thick section & shutter sec like handle/interlocking/top/ bottom should be of 1.2 mm thick etc , complete all as specified and as directed Note :Rates include all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle etc complete all as specified and directed.

M&L for grill medium grade of mesh size 75mmx75mm with 6mm square anodised aluminium bars fixed with suitable aluminum frame of size 37x19x2mm complete all as specified and directed.

S & F mild steel bars conforming to Fe 290 Gde E-165 as in guard bars or similar works including welding etc complete all as specified.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Non Skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exc 0.18 Sqm but n. exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed CM 1:6 complete all as specified and directed.

All as per item No 19 above but in verticle surfaces on 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for Glazed ceramic coloured tiles of size 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 15mm thick backing coat in CM 1:4 complete all as specified and directed.

Dismantling asbestos cement (corrugated or semi corrugated, etc)sheets in roof covering complete all as specified.

Dismantling wall and ceiling boards any thickness including cover fillets complete all as specified and directed.

S&F 4mm thick coloured textured designer ceiling board (Everest) of size 595X595 mm fixing with screws/clips including Tee grid suspension system of size 600 mm x600 mm type-1 made out of roll framed hot dipped galvanised steel zinc coated of not less than 120 gm/sqm ,main runner shall be 0.3 mm thick of section 24 mmX33 mm cross runner 0.3 mm thickof section 24 mmx25 mm,wall angle shall be 0.63 mm thick of section 24 mmx24 mm grid shall be suspended by 4 mm dia adjustable quick fit hanger rod ,system exposed portion shall be pre painted polyster coated in off white/white in colour complete with material,fixing, jointing etc complete all as specified and directed. ( Make:- METROC or METACIL or any other equivalent make as approved by GE.

Demolition of Brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Taking down cement or lime plaster of any description from stone or brick walls etc including raking out joints, hacking for key scrubbing down with water and disposing off the rubbish complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick/ concrete surfaces in CM (1:4) finished even and fair without using extra cement complete all as specified and directed.

M & L for 5mm thick rendering on cement concrete as in ceiling with cement mortar 1:3 complete all as specified and directed.

Supply only Integral waterproofing compound.

M&L for preparation of old plastered and un-plasterd surfaces on ceiling applying one coat of white wash complete all as specified

M&L for preparation of new plastered surfaces on walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for prepartion of new plastered surfaces on walls and applying two coats of cement based paint over one coat of primer on walls complete all as specified and directed by the Engr-in-Charge

M&L Preparation of old or previously treated steel surfaces of any description not other wise described, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed by EIC.

M&L for complete removal of existing treatment and applying two coats of cement based paint over one coat of Primer on walls complete all as specified and directed by the Engr-in-Charge

M&L complete removal of existing treatement and applying two coats of oil bound distemper over a coat of primer, on old plastered or un-plastered surfaces on walls complete all as specified and directed by Engr-in-Charge

M & L applying 2 mm thick wall care putty on wall for smoothing the surface complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) and disposing off the rubbish materials where directed complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate 75mm thick as in plinth protection including necessary form work and finishing surface even and smooth w/o using extra cement including bitumen joints complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

All as per item No 39 above but 20mm dia.

S&F 15mm bore tubes, `medium grade', galvanised, with all fittings and fixed complete concealed in walls and ceilings or laid in floors complete all as specified and directed.

S&F 20mm bore tubes, `medium grade', galvanised, with all fittings and fixed complete concealed in walls and ceilings or laid in floors complete all as specified and directed.

S&F in repair Bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed (15mm bore dia of pipe).

S&F in repair Stop valves cast copper alloy Chromium plated fancy type long sank concealed type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed (15mm bore dia of pipe).

Supply & fix 15mm dia brass CP mixer for WHB mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S &F in repairs vitreous china wash basins flat backsize 630 x 450mm including cutting for and pinning in ends of brackets or errecting stand white 32mm dia polyethylene flush pipe, PVC connections 15mm size with PTMT nuts of length 600 mm, 32mm dia Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed etc including brackets complete all as specified and directed.

S&F PVC valve less 10 litre capacity syphonic action type flushing cistern low level white with inlet ball valve float and handle including bracket and 32mm dia polyethylene waste pipe complete all as specified and directed.

S&F PVC connection 600mm long of dia 15mm complete all as specified and directed.

S&F in repairs Bath room cabinet (with locking plastic shelves ) 350 x 450 mm (Mirror cab) complete all as specified and directed.

S &F Wash down water closet (Pedestal pattern) white with P or S trap including plastic water closet seat & cover mild steel chromium plated or aluminised hinging device , flushing cistern low or high level, 32mm dia polyethylene flush pipe etc compete all as specified.(excluding cost of flush tank) Fixed in repairs

S&F tubular towel rail 20mm dia D type and 60cm long including brackets fancy type brass chromium plated complete all as specified and directed.

S&F Soap dish, vitreous China white, approximate size 160x 160x90 mm complete all as specified and directed.

S&F brass toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S & F Chromium plated shower rose 125mm with or without swivel joints, including fixing into steel pipe or union complete all as specified and directed.

Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed.

Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40 gms) complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc.,including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories)

S&F in repairs PVC (SWR) floor trap, plane with grating including jointing with solvant cement (Diameter of outlet 75mm) complete all as specified and directed.

M&L SGSW Gully trap squre or round mounted type 'P' 150mm x100mm complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in floor or fixied on wall complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipessoil waste and rain water drainage pipe (6 kgf/sqcm) single socketd, in any length with rubber ring joints laid in floor or fixied on wall complete all as specified and directed.

S&F PVC (SWR) 75 mm dia bend any radius with oval access door complete all as specified and directed.

S&F PVC (SWR) 110mm to 75 mm dia reducers complete all as specified and directed.

S&F PVC (SWR) vent cowl size 110 mm dia complete all as specified and directed.

S&F PVC (SWR) 110 mm dia bends any radius with oval access door complete all as specified and directed.

Excavating in trenches, n.exc 1.5m wide & n.exc 1.5m in depth; for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc. nexc 10 sq m on plan & n exc 1.5 m in depth & getting out getting out in soft/loose soil

M&L for plain Cement concrete1:4:8 type D2 using 40 mm graded stone aggt as in foundation, fillings & mass concrete complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering & well ramming in layer s not exc 25 cm in soft loose soil complete all as specified and directed.

Removing excavation material exe. 250m but n exc. 500m & deposited where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

M&L for brick work with sub class 'B' bricks built in CM (1:6) straight or curved on plan & exc 6 m mean radius with old size bricks complete all as specified and directed.

M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces of block masonary or concrete surfaces in CM 1:6 finished even and smooth complete all as specified and directed.

M&L for prepararion of new plsatered surface of wall and applying two coats of exterior emulsion paint over a coat of anti fungle primer complete all as specified and directed.

S&F mild steel angle iron work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe290 (Gde-E-165)

M&L for preparation of new steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified.

M&L for PCC 1:3:6 type C1 using 20 mm graded agg as in copping including necessary form work & finishing exposed surface of concrete complete all as specified and directed.

M&L providing pre cast cement concrete louverd and jallies ,40 mm thick including all moulding complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, thick watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed.

M & L 1:3:6 type C-2 (40 mm graded aggregate) Cement concrete in foundations, filling and mass-concrete complete all as specified and directed.

S&F Joist, channel, angle, or tee sections, as in fencing post fixed independently, without connecting plate, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) FE -410 (Gde-250) quality A complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long dia 16 to 20 mm complete all as specified and directed.

Supply only chain link MS galvanised fencing of aperture size 75mmx75mm dia 4.0mm weight not less than 6.0 kg complete all as specified and directed.

M&L for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

M&L for preparation of new steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified.

M&L for RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

Surface excavation n.exc 30 cm deep & averaging 15 cm deep getting out in soft / loose soil complete all as specified and directed.

M&L for 25 mm thick DPC in cement concrete 1:2:4 type B0 to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L, Rendering 15 mm thick on fair faces of brick or concrete surfaces in CM 1:4 on wall with water proofing component complete all as specified and directed. Note : WPC measered and paid seperately

S&F 200 mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified & directed.

M & L 75mm thick plain cement concrete type D-2 1:4:8 (40 mm graded stone aggregate) as in sub base complete all as specified and directed.

S&F TMT bars 10mm dia & over cut to length, bent to shape required including cranking bending spirally for hooping for column, hooking ends &binding with & including mild steel wire (not less than 0.9mm dia), or securing with clips quality conforming all as specified and directed.

S & F prepainted galvalume aluminium zinc coating GI base corrugated steel sheet 0.50 mm thick of approved colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specfieid and directed. (Note : Corrugation shape of sheet shall be approved by GE)

M&L for cement concrete 1:2:4 type B2 (using 40mm graded aggregate) in foundation filling & mass concrete as in post

Supply only mild steel round bars 10mm dia & over cut to length, bent to shape required including cranking, bending etc. complete as in rungs, steps Fe-410-W (Gde.E-250) quality -A 0r Fe290 (gde E-165) all as directed by Engr-in-Charge

M&L 40mm thick cement concrete type B1 (1:2:4) as flooring finished surface even & smooth without using extra cement complete all as specfieid and directed.

S&F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.5 mm thick of any colour having tensile strength 550 Mpa as in ridge / vally gutters fixed with self tapping screw complete all as specfieid and directed.

S & F steel work in MS angle , trusses/ purlins/ post / rafters or in similar work including speherical shaped washer etc. MS plate of required thickness and mild screw bolts (machine made) conforming to Fe-290(gde E-165) complete all as specfieid and directed.

Supply, laying and testing of LT UG cable, XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sqmm 4 core , complete all as specified and directed. Note: Earth work ( Excavation, Returning & refilling and removal), sand cushining , cable protection cover, GI protection pipe shall be measured and paid for seperately under respective item of Sch 'A'. .

Supplying and laying factory made un-reinforced precast concrete cable cover, class LV, type 1, flat, size 250mm x 150mm x 40mm laid in trenches over sand for cable protection complete.

M&L for steel tubular swaged pole 8.5 m long type 410 SP-22 with cast iron or welded MS base plate including nuts / bolts / washers etc conforming to IS-2713 (Part I to III) of 1980 and comprising of following:-

Excavation in post holes in any type of soil not exceeding 0.5 cum each, getting out, returning filling in and ramming earth in layers not exceeding 25 cm watering and disposal of surplus soil to a distance not exceeding 50 m and making good surface.

PCC (1:4:8) type D2 using 40 mm graded stone aggregate in base (0.60 m dia x 0.15 m height).

PCC (1:3:6) type C2 using 40 mm graded stone aggregate in foundation filling (0.60 m dia x 1.5 m height).

PCC (1:2:4) type C2 using 40 mm graded stone aggregate in coping (0.6 m dia x 0.45 m height).

Pole cap 0.30 m long externally fitted on pole top duly welded with a light grade ISI marked 40 mm GI pipe bracket 1.5 m long for mounting street light fitting.

Painting with aluminium paint one under coat, one finishing coat over a coat of red oxide primer and making alternate colour bands of black & white colours in 30 cms width upto a height of 1.5 m from pole coping with synthetic enamelled paint complete.

Supply and fix Polystyrene body IP 65 cable junction box with connector metric knockouts on all sides for cable entry size 200 x 160 x 98 mm as per Hensel cat ref no. K 9255 or equivalent duly fitted with followings:-

ELMEX or equivalent make end plate - 1 No

ELMEX or equivalent make end clamps - 2 Nos

Clamp made of 30x5 mm flat iron duly painted with two coats of aluminium paint over a coat of red oxide primer suitable for steel tubular swaged pole type 410 SP-31.

Supply, installation, testing and commissioning of integral driver LED street light with a nominal system lumen output of 7200 lumens and a minimum system efficacy of 90 lumen/watt. The luminaire shall have rated system lifetime of 50,000 burning hours before reaching at L70. The luminaire should have cool white colour temperature (CCT > 5000K) and a CRI >70. The luminaire shall meet IP 66 rating & IK05 rating with THD < 20% & PF > 0.9. The luminaire housing should be made of pressure die cast aluminium with a flat glass optical cover. The total power consumption should not exceed 72 watt including driver and suitable capacity of copper cable from junction box to light fittings for connection complete. Make - Philips Greenline cat ref BRP410 LED CW 072 MR FG S1 PSU GR or equivalent in Havells or Wipro Cat No LR02-781-XXX-57-XX as approved.

ALPINE CONSTRUCTIONS

SNEH TRADERS