Construction of Auditorium at Uttrakhand Sanskrit Academy at Haridwar

Amount

CIVIL WORKS:Excavation in foundation :in ordinary soil including lift up to 1.5 meter (5ft) and lead up to 30 meters (100ft) and including filling , watering and ramming of excavated earth into the the trenches or into the space between the building and the sides of foundatin trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer-in-charge trenches including cost of labour T&P complete. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with Jamuna sand under floors including, watering, ramming consolidating and dressing complete.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil for Pipes, cables etc, not exceeding 80 mm dia.

Diluting and injecting chemical emulsion (chlorpyriphos/Lindane E.C 20% with 1% concentration) at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surface of the excavation made for the foundation of the building, soil under footings etc. complete.

Supply and Filling of carted earth in plinth including dressing and ramming in specified layer (Carrriage of material 15 Km/lead) by mechanical transport as per DSR

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : "1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).

All works upto plinth level

All works above plinth level upto floor V level

Centering and shuttering including strutting, propping etc. and removal of form for all heights :

Foundations, footings, bases of columns, etc. for mass concrete.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Suspended floors, roofs, landings, balconies and access platform.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured) Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand).

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand).

Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry (with F.P.S. bricks).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.5 mm thickness

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ eoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) with Powder coated aluminium (minimum thickness of powder coating 50 micron.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness.

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 4 mm.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile B Fixing with adjustable lugs with split end tail to each jamb.

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 12 mm mild steel U beading.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 1 Fixed to steel windows by welding.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Makrana white second quality.

Marble stone flooring in risers of sq.m steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of tile 600 x 600 mm.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing M.S. angle 50x50x5 mm to act as nosing with lugs of M.S. flat 10x5 mm, 10 cm long, forked at end 60cm apart (minimum three lugs to be provided), including necessary welding and applying a priming coat of approved primer on exposed surface etc. complete.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly he adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120mm and minimum thickness at khurra as 65 mm

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75mm deep chase

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

Bend 87.5 degree 110 mm bend

Shoe (Plain) 110 mm Shoe

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. 100 mm diameter.

15 mm thick cement plaster in cement mortar 1:6 on Rough face of brick wall including supply of all material , labour and T&P etc.

12 mm thick cement plaster in 1:6 ( 1 cement and 6 fine sand) mortar including supply of all material , labour and T&P etc. required for proper completion of the work.

Applying priming coat With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood).

Applying priming coat With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works.

Finishing walls with textured exterior paint of required shade New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including sq.m base coat of water proofing cement paint applied @ 2.20kg/10 sqm.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade (New work (two or more coats) over and including priming coat with cement primer)

Painting work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type each foot rests.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm.

P/F S C.I. soil, waste and vent pipes 100 dia. Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 100 x 100mm

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Fixing white vitreous china flat back half stall urinal : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern.

Providing and fixing 100 mm sand cast iron s&s terminal guard

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length and 15 mm nominal bore

Providing and fixing plain bend of required degree. 100 mm dia, Sand cast iron S&S as per IS - 1729

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia, Sand cast iron S&S as per IS - 1729

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia

Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100x100x100x100 mm Sand cast iron S&S as per IS - 1729.

Providing lead caulked joints to sand cast iron rain water pipes and fittings: 100 mm dia Pipe

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall

20 mm nominal bore.

25 mm nominal bore.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (external work)(25mm dia nominal bore)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15mm

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15mm

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

20mm dia.

25mm dia.

Providing and fixing PTMT grating of approved quality and colour. Circular type 100 mm nominal dia.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet, and overflow pipes but without fitting and the base support for tank.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 20 mm nominal bore, 120 mm long, weighing not less than 198 gms.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore.

Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. 15 mm nominal bore

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm diameter.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all- round S.W. pipes including bed concrete as per standard design : 100 mm diameter S.W. pipe.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for masonry M.H 90X80X45cm

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade. 8mm thick (mirror polished and machine cut edge) Granite stone of any colour and shade

French spirit polishing two or more coats on new work i/c a coat of wood filler.

Construction of Masonry Drain with brick work, plaster work etc. complete.

38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half depth, planed, levelled smooth and finished complete.

Providing and fixing 2nd class teak wood plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface. 40mm thick

Providing and fixing false ceiling and wall pannelling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60.

Providing and fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 12.51.1 Ridges plain (500 - 600mm)

Providing and Fixing Gutter ( 600mm )

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting o

Same as above but for Terrace cutting.

R/R Stone Masonry in 1:6 Cement sand mortar in foundation.

P.C.C. in 1:2:4 cement/ C. sand/ S. grit mortar

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge.

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse and), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

E & M Works:

Supply, Testing & Commissioning Addressable Accessories modules surface mounting box for optical smoke

Supply, Testing & Commissioning Addressable Accessories modules surface mounting box for heat smoke

Supply, Testing & Commissioning Addressable Low Profile

Supply, Testing & Commissioning Addressable Low Profile heat Smoke sensor the indicator LED whichis clear in standby and rred in alarm .an Requires either Rate of Rise +Fixed Heat sensor. 58 degree C, EN54 part 5. Type A1. Requires either MOFMIB501APIV, B5241E or B5241EFT Base for mounting. Base for Addressable Detectors and Sounders, Ivory Color.

Supply, Testing & Commissioning Response indicator with single LED in 16SWG MS Sheet.

Supply, Testing & Commissioning Addressable manual push button Addressable manual call point. No Glass Included. Requires SR3TPC/ ABS for surface mounting or terminal tray ETTP and single gang back box for flush mounting.

Supply, Testing & Commissioning Addressable Hooters suitable for Alarm siren with suitable power supply unit. Intelligent Wall Mounted Sounder, Red with pure white skirt

Supply of microprosser based 2 zone advance fire alarm panel with 2x16 character backlit LCD display and keypad with integral power supply & battery charger, capable for indication of OPEN. Short circuit, isolate, Fire in each zone

Supply, installation testing, commissioning drawing, connecting, testing & commissioning of 2 core, 1.5 sq. mm. stranded copper conductor, FRLS insulated & PVC sheathed wire in pvc conduit. The cost of conduit is included in this item.

Supply, testing and commissioning of battery Back-up for Main Control Panel with battery.

SITC of single way Hydrant Valve, 63 mm dia straight outlet with 75 mm NB flanged inlet SS pindle, 63 mm female oblique outlet complete.

SITC of Non-percolating flexible (Primer) fire hose pipe with circularly woven jackfzet of 100% polyester yarn lined with black synthetic EDPM rubber resistant to heat, Abrasion and fungus having bust pressure 38 kg/cm2 ISI mark IS: 636: 88 Type-A With Male & Female coupling .

SITC of GM 63 mm dia short branch pipe with 20 mm dia nozzle with 63 mm instantaneous coupling.

SITC of GI Fire Brigade connection (Suction collecting head) consisting of 63 mm dia instantaneous type male coupling with built-in check valve and 150 mm dia flanged outlet complete with bolt, nuts and rubber insertions as required.

a) Two way

SITC of weather proof M.S hose box suitable for accommodating yard hydrant of 18 swg MS sheet with control opening, glazed and including necessary locking arrangement, painting one coat of primer and two coats of P.O red paint for housing 2 nos. canvas hose pipes, one no, & branch pipe. The word “etc. to be painted on each box. Including suitably mounted on a raised masonry platform as required (App. 0.75m x 0.6m x 0.25m)

SITC of black steel class “B” pipe as per IS: 1239 part l or fitting like flanges, tees, elbow, bend, junctions, reducer including cutting holes in brick or RCC wall/slab and making good the same the same complete including painting with one coat of primer and two coat of synthetic enamel paint of approve make and shed including all steel work. Including all support and hanging arrangement.

Providing & Fixing of Hose Reel drum swining type fitted with 20 mm rubber hose 30 meter length with shutt off nozel.

supply of pendant type autoatic water sprinkler

Supply of structural steel supports such as MS channels, angles, flats etc. as required including anchor, fasteners, clamps threaded rods, nuts, bolts, washers etc. complete with painting.

SITC of Tarrece pump set, for giving discharge of 1200 LPM End Suction Top Discharge, when directly couple to 30 HP TEFC motor, 2900 RPM with Gland packing, with Necessary Base Plate Foundation Bolts, Coupling guard, bronze impellor etc complete.

SITC of Jokey pump set, for giving discharge of 450 LPM End Suction Top Discharge, when directly couple to 25 HP TEFC motor, 2900 RPM with Gland packing, with Necessary Base Plate Foundation Bolts, Coupling guard, bronze impellor etc complete.

SITC of M.C.C. With Star Delta starter for the electrical motor main pump set complete with isolator switch, voltmeter, ammeter manual/auto mode switch, indicating lamps etc. Auto start panel for complete auto/ manual switch

Supply & Laying of 3.5x16mm sq. Al. armoured Cable termination for above

Supply & Laying of 3.5x25mm sq. Al. armoured Cable termination for above

SITC of MS cylindrical type air vessel with dished end, 250 mm dia, 1m high of thickness 6 mm complete with 25 mm dia G.I pipe connection with delivery header and drain including stop valve, air release valve, safety valve, pressure gauge, stand etc

SITC Of Providing of CI body Y strainer 100 mm (For main pump)

SITC of of pressure gauge 100 mm dia 0-10kg/cm2 with socket, nipple, ball valve and u tube (For main pump and jockey pump)

SITC of NRV 100 mm dia ISI marked complete with all fitting viz flange, gasket nut and rubber insertion etc.

SITC of Butter Fly valve 100 mm dai ISI mark as per specification.

Wiring for light point/ Fan point/ Exhaust fan point with 1.5 sq. mm. FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit with modular switch, modular plate, suitable G.I. box and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit along with one no. 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. 2x2.5 sq.mm+1x2.5 sq.mm earth wire.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. 4x4 sq.mm+2x4 sq.mm earth wire.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. 4x10 sq.mm+2x10 sq.mm earth wire.

Supplying and fixing 3 pin 5/6 amps modular socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 5/6 amps modular switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supply and fixing of suitable size G.I. box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc. as required.

Supply and fixing of suitable size G.I. box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket out let and 15/16 amps modular switch, connection, painting etc. as required.

Supply and fixing 3 pin, 5 amp. Ceilling rose on the existing junction box/ wooded block including connection etc. as required.

Supply and fixing brass batten/ angle holder including connection etc. as required.

Installation,testing and commissioning of celling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation Testing & commissioning of resistance type electronic fan ragulator in exiting switch box including connection with 1.5sq.mm FR PVC insulated, copper conductor, single core cable and earthing the regulator etc. as required.

Installation of exhasust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.

Supply and fixing following way, three pole and neutral, prewied, sheet steel, MCB disribution board, 415 volts, on surface/ recess.complete with loose wire box, terminal blocks, duly prewired with suitable size FR PVC insulated copper conductor up to terminal block, tinned copper busbar, neutral ink, earth bar, din bar, detachable gland plate, intercnnections, phosphatized and powder painted including earthing etc. as required ( But without MCB/RCCB/ lsolator.) 6way(4+18), Double door.

Supplying and fixing 5 amps to 32 amps rating, 240 volts, "C" series, minature circuit baeaker suitable for inductive load of following poles in the existing MCB DB complete with connection, testing and commissioning etc. as required. Single Pole.

Supplying and fixing folowing rating, four pole, (Three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connection, testing and commissioning etc. as required. 25 amps

Supplying and fixing folowing rating, four pole, (Three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connection, testing and commissioning etc. as required. 40 amps

Earthing with G.I. earth plate 600 mmx600mmx6 mm thick including accssories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but with charcoal or coke and salt) as required.

Supplying ans laying 25 mmx6mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering etc. as required.

Supply & fixing of PVC conduit pipe along with accessories in surface/ recess including the wall & making good same in case of recessed conduit as required 20 mm

Supply & fixing of PVC conduit pipe along with accessories in surface/ recess including the wall & making good same in case of recessed conduit as required 25 mm

Supply of 1200 mm size ceiling fan.

Supply of 300 mm size exhaust fan.

Supply, installation testing, commissioning of Curtain Wireless Controller 1 circuit:2 buttons for open close

Supply, installation testing, commissioning of Smart System(HRIS) Control Host

Supply, installation testing, commissioning of Lighting Wireless Controller- 2 group, two wires

Supply, installation testing, commissioning of IR Generator

Supply, installation testing, commissioning of Controller with remote, English Version

Supply, installation testing, commissioning of Motorised Stage Curtain Micro Switches with push button with Steel wire rope 3mm vertical ballon reverse and stop position size 60’x25’

Supply, installation testing, commissioning of Motorised rear Stage Curtain Micro Switches with push button with Steel wire rope 3mm vertical ballon reverse and stop position, runner/master and pulley size 50’x25’

Supply, installation testing, commissioning of 1000W PLANOCONVEX Spot Light Complete 1000W, Halogen Bipin T-11 Lamp, G-38 base socket, spherical anodrised refelector 200 mm dia planoconvex lens

Supply, installation testing, commissioning of 1000W Profile Light consisting of 2 nos, 150 mm dia Pc lenses, elipsodial alluminium refelector

Supply, installation testing, commissioning ofHousing CRC Sheet Metal Holder with tip contact, copper wire analog beam.

Supply, installation testing, commissioning of 500w Halogen Cyclorama Flood Light with Halogen Tube and anodized refelector.

Supply, installation testing, commissioning of Fresnal Light 1000 w with suitable halogen lamp, with fresenel lamp, with cable and lamp socket with CRC Sheet metal and 1000 W PAR sealed Beam Light.

Supply, installation testing, commissioning of Electronic dimmer wall mount type 24 kw eac with 16 CH frequency level of 60 HZ, liner dimmer, high quality RF noise suppression, radio frequency.

Supply, installation testing, commissioning of 18 CH 4 way inbuilt two dimmer for light point to inter change,

Supply, installation testing, commissioning of 24 CH Control Panel sub master manual control with 2 sub master with USB Port

Patch Panel to Light Bar Socket at Stage light point to be fixed on Light bar with 2.5 mm 3 core copper conductor cable with bar lighting system.

Supply, installation testing, commissioning of Box speaker-acclaim 5 series 4’outdoor 2way, 100watts-white (woofer:4’impp cone, tweeter, 1”tetron Mounting Option

Supply, installation testing, commissioning of Box speaker-acclaim 5 series 6.5”’outdoor 2way, 150watts (woofer:4’impp cone, tweeter, 1”tetron Mounting Option

Supply, installation testing, commissioning of Acclaim 5 series 5 point 25”Outdoor Speaker

Supply, installation testing, commissioning of Ceiling LSP 9/6 Watt Acclaim 5 series 5 point 25”Outdoor Speaker

Supply, installation testing, commissioning of Power Booster Amplifier R Series 6Zone 12channel Multi Room Amplifier

Supply, installation testing, commissioning of Power Booster Amplifier X Series 2channel Dual Source

Supply, installation testing, commissioning of Wired condenser Microphone

Supply, installation testing, commissioning of Table Top Wired Microphone

Supply, installation testing, commissioning of Hand Held Dynamic Microphone

Shri Balaji Enterprises