SPECIAL REPAIRS TOBLDG NO P-1 AND P-2 AT KATIHAR MIL STN UNDER AGE (I) KATIHAR

Amount

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, disposing off the retrieved debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, disposing off the debris outsite the premises, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after prepation of the surfaces, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after prepation of the surfaces, complete all as specified and as directed.

S&F factory made IInd class Hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35mm thick plain framed, panelled shutters ( Two panels),with lock rail and penel of 9mm BWP commercial ply or 12mm veneered particles board with commercial veneering on both faces. the size of rail and stile as per IS 1003 (Part-I), complete all as specified and as directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze, etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and shown on drawing for SI No. 08095 on Srl Page No. 180 of SSR (Part-II) and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,, complete all as specified and shown on drawing for SI No. 08080on Srl Page No. 176 of SSR (Part-II) and as directed.

S&F Factory made 30mm thick flush shutter solid core construction, with MDF board and one face is covered with decorative face veneer with lipping/frame to match, complete all as specified and as directed.

M&L for preparing new wooden surfaces of any description not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed .

M&L for cement concrete (1:3:6) type C-1 (using 20mm graded crushed stone aggregates) as in hold-fast blocks, blocks for fixing lugs, filling of pressed steel chowkhat and the like including necessary form work, complete all as specified and as directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ tainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level), Complete all as specified and directed.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of (3:1), complete all as specified and directed.

M&L for 100mm thick PCC (1:4:8), type D2, (using 40mm graded crushed stone aggregate) as in sub-base of of floors etc; finished fair & even/rough , complete all as specified and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L for cement concrete 1:2:4 type, B1 (using 20 mm graded crushed stone aggregates) as in copings, Chajja, kerbs, benching at the junction of roof & parapet, roof kerbs, staging of water tank etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

Cutting chases in brickwall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm but n exc 20cm girth, complete all as specified and directed.

Taking down 15mm bore steel tubing & connections, complete all as specified and as directed.

Taking down 25mm bore steel tubing & connections, complete all as specified and as directed.

Supplying and laying of 15mm bore of uPVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe, complete all as specified and as directed.

Supplying and laying of 25mm bore of uPVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe, complete all as specified and as directed.

S & F in repairs 110 mm bore PVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends (any radius), complete all as specified and directed.

S&F in repairs Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and verage width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

S&F 4mm thick sheet glass of ordinary quality and glazing for Wooden Joinery or for steel surrounds with & including oil putty, in squares n.exc 0.5sqm in each pane, complete all as specified and as directed.

S&F 4mm thick figured sheet glass for Wooden Joinery or for steel surrounds with & including oil putty, in squares n.exc 0.5sqm in each pane, complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F 125mm size butt hinges, heavy weight, cold rolled, mild steel, complete all as specified and as directed.

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 150 mm long of extruded section, complete all as specified and as directed.

S &F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specifiied and directed.

S&F 140mm (overall length of cover plate) Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles of size 450mmx 300mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM (1:4), complete all as specified and and as directed.

M & L for light shade vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

M&L for light shade vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces such as skirting etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 10mm thick cement morter backing coat in CM 1:4, complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site outside the premises, complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar (1:6), on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surfaces finsihed even and smooth (without using extra cement) mixed with water proofing compound and polyster tringular fibre as per manufacturer instructions, complete all as specified and as directed. Note:- WPC and polyster tringular fibre shall be measured and paid seperately.

Supply only liquid water proofing compound, complete all as specified and as directed.

Supply only polyester tringular fibres as secondary reinforcement in all type of concrete and mortar, complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls, applying two coats of wall care Putty (minimum thickness of two layers shall be 1.5mm) and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for preparing new plastered surfaces of walls and applying two coats cement base paint over a coat of primer, complete all as specified and as directed.

M&L for preparing old plastered surfaces of walls and applying one coat cement base paint, complete all as specified and as directed.

M&L for preparing old plastered surfaces of walls, applying two coats of oil bound distemper, white or any tint as approved, complete all as specified and directed.

S&F in repair stop cock, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed.

S&F in repairs bib tap, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed.

S&F in repair angular stop cock, 15 mm bore, chromium plated, complete all as specified and as directed.

S&F in repairs pillar taps, fancy type, cast copper alloy, with long swan neck , chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified and as directed.

S&F in repairs Vitreous China Wash Down Water closet (Pedestal Pattern) 1st quality, , white (excluding flushing cistern & flush pipe) including plastic water closet seat white, closed pattern with flat bottom and cover and mild steel CP or aluminised huiging device, making connections, complete all as specified and as directed.

S&F in repairs PVC valveless, double syphonic action type, flushing cistern, low level of 10 Litres capacity, white, with and including inlet, ball valve, float, 32mm dia flush pipe of polyethylane of low or high density or PVC, flushing bend & handles, also including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet & making connections, complete all as specified and as directed.

S&F in repairs vitreous china wash basin, 1st quality, white, flat back, approx size 550x400 mm excluding taps but including 32 mm bore brass chromium plated waste fittings, 32mm bore PVC waste pipe, MS brackets, complete all as specified and as directed.

M&L for Granite (of any type) tiles 15mm thick machine cut as in steps, jambs, pillars, window-cills, cooking platform etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 15mm thick screed bed in CM (1:4), complete all as specified and directed.

S&F sink with drainage board made of 1mm thick sheet of stainless steel (Bronze range 204 super steel : Matt) for kitchen or laboratory with and including plugs, washers, wastes; 40mm bore PVC waste pipe, also including bedding in cement mortar (1:3) on dwarf wall or including providing mild steel cantilever brackets and connecting union to pipe, overall approx size 914mm x 460mmx203mm with bowl size 405mm x 354mm x 203mm, complete all as specified and as directed.

S&F in repairs brass chromium plated shower roses, 125 mm size with or without swivel joints including fixing to 15mm bore steel pipe or union, complete all as specified and as directed.

S&F in repairs PVC connection 15 mm size with PTMT nuts of length 600 mm, complete all as specified and directed.

S&F in repairs tubular towel rail, 20mm dia, D type, stainless steel, 600mm long between flanges, complete all as specified and as directed.

S &F in repairs stainless steel kitchen plate rack of overall approx size 600 x 900 x 250mm, complete all as specifiied and directed.

S&F in repairs Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified and as directed .

S&F in repairs Grating doom 100 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified and as directed .

S&F in repairs PVC waste pipe suitable for 32mm bore dia of waste coupling, complete all as specified and as directed.

S&F in repair for cast iron floor trap 75mm dia of outlet, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tank 1000ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete all as specified and as directed.

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for Brickwork withsub class 'B' old size Bricks, straight or curved on plan exc 6m mean radius built in Cement morter (1:6), complete all as specified and directed

M&L for brick work with sub class 'B' old size Bricks, straight or curved on plan to any radius built in CM (1:4) as in half brick thick walls, complete all as specified and as directed.

S&F in repairs shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms), complete all as specified and directed.

S&F in repair harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

S & F 4mm thick Non-asbestos fibre cement decorative/designer building boards to steel frame work with screws in ceiling (flat and/or slopping) and including jointless finish with & also including joining compound and tape as per manufacturer instructions, complete all as specified and as directed. Notes :- (i) The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process. (ii) Aluminium frame work shall be measured and paid for separately.

S&F anodised aluminium snap grid of size 605x605mm frame work for false ceiling hangers 6mm dia GI (upto 1200mm length) adusting level fixed to roof slabs by means of ceiling cleats made out GI flat iron 40x3mm size 60mm long and fixed expansion hold fasteneners 12.5mm dia and 40mm long, complete all as specified and as directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings), complete all as specified and directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L for Preparation of steel and iron surfaces of any description duly applied with shop coat of primer, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint, complete all as specified and as directed. Note : Cost of application of shop coat of primer not included in this item.

Dismantling wrought iron as in rafters, purlins, truss etc and/or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240, complete all as specified and as directed.

M&L 18 mm thick PVC steel plelaminated economic/ economic colour both side, cut accordingly to the size of the cabinet or for kitchen drawer provided and the groove to be made on the one edge so that the overlapping could be done for double leaf shutter includoing fixing with 1.25'' Mild steel screw to the frame with the channel, complete the work as per manufacturer instructions, including dismantling of old one, complete all as specified and directed.

M&L 9mm thick sheet plelaminated economic/ economic colour both side, cut according to the size of the cabinet Sqm or fo kitchen drawer provided and the groove to be made on the one edge so that the overlapping coild be done for double leaf shutter includoing fixing with 1.25'' Mild steel screw to the frame with the channel, complete the work as per manufacturer instructions, including dismantling old one, complete all as specified and directed.

S&F telescope drawer channel 20" steel silver chrome plated fixed with mild steel screw to the frame with cannel complete all as specified and directed.

S&F Stainless steel handles 100mm fixed with screw complete all as specified and as directed.

S&F in repair auto close stainless steel (Clip hignes) 75 mm size suitable for cupboard shutter fixed in position with stainless steel screw, complete all as specified & directed.

Taking down carefully existing aluminium point wiring (light / fan / socket or power point) complete, with all fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed.

Material and labour for concealed point wiring for one light point/one fan point/ one exhaust fan point/bell point controlled by 1 one way switch with FRLSH PVC insulated unsheathed multistranded copper conductor cables 1100 Volts grade of 1.5 sqmm size alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade of 1.5 sqmm size through and including 20 mm dia (medium grade) rigid non metallic PVC concealed conduit terminated in and concealed modular metal box with cover plate (measured and paid seperately) for fixing of switches, sockets, fan regulators etc including testing on completion, connected to earth dolly and to be terminated in and including making good the surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per Item No 89 above but for one switch socket outlet, 3 pin, 6 Amp on same board all as specified and as directed.

All as per Item No 89 above but for one switch socket outlet, 5pin, 6 Amp on independent board all as specified and as directed.

All as per item No 89 here-in-before but for one 6/16 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLSH) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, complete all as specified and as directed.

S & F Modular Switch 1 way 6A, 1 module complete all as specified and directed.

S & F Modular Switch 1 way 16A, 1 module complete all as specified and directed.

S & F Modular Socket 6 A, 2/3 pin combined 2 module complete all as specified and directed.

S & F Modular Socket 6 A/ 16 A, 2/3 pin combined 2 module complete all as specified and directed.

S&F call bell ding dong, 230V single pole, complete all as specified and directed.

S&F modular bell push 6A, 1 module, complete all as specified and as directed.

S&F ceiling rose, 3 phase /PVC/Polycarbonate, isolated body, complete all as specified and as directed.

S&F Lamp holder, PVC/Polycarbonate type with back plate, complete all as specified and directed.

S & F Modular Regulator Step Type 120 watt, 2 module complete all as specified and directed.

S & F Modular type White cover plate with frame 1 module complete all as specified and directed.

S & F Modular type White cover plate with frame 3 module complete all as specified and directed.

S & F Modular type White cover plate with frame 8 module complete all as specified and directed.

S & F Modular type Metal Flush box 1/2 module complete all as specified and directed.

S & F Modular type Metal Flush box 3 module complete all as specified and directed.

S & F Modular type Metal Flush box 8 module complete all as specified and directed.

S & F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 20Amps, 240v, complete all as specified and directed.

S &F for wall mounted LED tube linght fitting 1x20 watts (4 feet) batten for surface, anodized extruded aluminium housing, high transmisivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc complete with all accessories interially pre-wired and necessay mounting arrangements, provision of new 3 core multistranded copper counductor of size 23/0.193 form ceiling rose to fiting complete all as specified as directed.

S &F for wall mounted LED tube lingh fitting 20 watts (2 feet) batten for surface, anodized extruded aluminium housing, high transmisivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc complete with all accessories interially pre-wired and necessay mounting arrangements, provision of new 3 core multistranded copper counductor of size 23/0.193 form ceiling rose to fiting complete all as specified as directed.

S &F in repair LED street light fitting 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection all as specified as directed.

S&F in repair sheet metal enclosure for MCBs DBs, SPN, 8 way with 200Amps rated bus bar 240 volts, Double Door with magnetic locking system, Powder coated including necessary provision for inserting the DBs in wall by cutting the bricks/stone masonary etc and making good of disturbed surfaces to match with existing colour of wall, complete all as specified and as directed.

S & F MCB, 'C' curve, SPN, 240 volts breaking capacity 10KA, 32Amps, breaking capacity 10KA, complete all as specified and directed.

S & F MCB, 'C' curve, SP, 240 volts breaking capacity 10KA, 6 to 32Amps, breaking capacity 10KA, complete all as specified and directed.

Material and labour for sub main wiring for main DB's to sub DB's with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLHS cable of size 4.0 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLHS cable of size 4.0sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 20 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces and including taking down old one, complete all as specified and as directed. Note:- For payment purposes, 2 runs of main cable (each of 1RM) 1 run of earth continuity cable (1RM) and one run of conduit (1RM) all together shall be considered as "1RM".

Supply and fix ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor, complete all as specified and directed by the Engineer-in-charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 300m, complete all as specified and directed by the Engineer-in-charge.

S&F LED Street Light 60 Watt made up of pressure die cast aluminiun housing with highly efficient LEDs and PC cover with integrated lens with IP66, IK07, System Lumen Efficasy ≥100 Lm/W, 5 kV Surge Voltage Protection, Operating Voltage range 140 V - 270 V including provision of twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

S&F street light bracket made out of 40 mm bore GI Light grade pipe 1.00 M long bent to the shape as required for steet light fittings pronded with two pairs of MS Flat Iron 50mm x 6mm clamps of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete, complete all as specified and directed.

Supplying, laying, jointing and testing XLPE insulated, screened, PVC bedded, galvanized steel strip, heavy duty, wire armoured electric LT power cable with stranded aluminium conductor 1100 volts grade, cross sectional area 10 Sqmm x 2 core in trenches /along poles/on wall etc including taking down old one, complete all as specified and as directed Notes : - (i) Excavation and earth work, sand cushioning, protection covers shall be measured and paid for separately. (ii) Unless otherwise directed by the GE, the cable shall be procured by the contractor in single length (as manufactured) to meet the actual length of cable as required at site. However, for payment purpose, the length actually ordered & laid shall be measured and paid for.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation,laying of cable, pipe etc. or for shafts, wells, cesspits, manholes, pier holes, etc. nexc 10 sq m on plan and n exc 1.5 m in depth and getting out, complete all as specified and directed.

Returning, filling in, including spreading, watering and well ramming in layers not exc 25cm thick in layers, complete all as specified and directed.

Removal of surplus spoil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point, complete all as specified and directed.

Material and labour for well burnt Sub-class 'B' old size bricks, best quality locally available laid flat, dry in trenches for cable protection, complete all as specified and as directed.

M& L for Sand cushioning in trenches for cushioning of underground cable including spreading, levelling, well ramming in layers , complete all as specified and directed. Note: Punned thickness 18cm shall be considered for payment as per para 19.75 of SSR Part-I)

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc., complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, PCC (1:3:6) type C-1 with 50 mm thick Pre-cast RCC (1:2:4) type B-1 cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth strip protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 m and necessary testing on completion, complete all as specified and as directed.

M/s.Abhay Kumar Roy (BID ID -3270668)

BISWAJIT SAHA (BID ID -3278015)