SPL REPAIR TO CERTAIN SUB STATION, PUMP HOUSE AND CERTAIN SANCTIONED WORKS (PHASE-7) AT MISA CAMP UNDER GE (S) TEZPUR

Amount

Surface dressing n.exc 15 cm deep in soft/loose soil.complete all as specified and directed.

Surface excavation n. exc. 30cm deep and avererging 15cm deep and getting out.complete all as specified and directed.

Excavation in trenches n exc 1.5 mtr depth nd n exc 1.5 m wide in soft/loose soil and getting out.complete all as specified and directed.

Excavation in post holes (or similar holes ) each n'exc 0.5 cum , getting out , returning , filling in and ramming earth or rubble mixed with earth around , in layers n'exc 25 cm watering , and removing surplus soil to a distance n'exc 50m and making good surface of soft/loose soil.complete all as specified and directed.

Returning/Filling in trenches in layer n exc 25 cm thick including watering well ramming etc.complete all as specified and directed.

Removing excavated soil to distance n exc 50 mtr and deposited as directed by Engr-in -Charge.

M&L PCC (1:4:8) type D-2 using 40 mm graded stone agg as in fdn filling mass concrete.complete all as specified and directed.

M&L cement concrete type C2 (1:3:6) 40mm graded aggregate) in foundation, filling and mass concrete.complete all as specified and directed.

M&L for RCC M-25(Design Mix) ( 20 mm graded agg) as in foundation, base for column , plinth beam etc complete all as specified and directed

M&L for RCC M-25(Design Mix) ( 20 mm graded agg) as in column, post etc complete all as specified and directed

M&L for RCC M-25(Design Mix) ( 20 mm graded agg) as in roof slab supported on wall, beam, landing, desk slab etc complete all as specified and directed

M&L for RCC M-25(Design Mix) (20mm gradded agg) as Lintel/chajja etc complete all as specified and directed

M&L for RCC M-25(Design Mix) (20mm gradded agg) as Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

Use & waste of form work of the side of the concrete foundation, footing, base of column rough finished flat surface.

Use & waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick ( Horizontal or sloping).complete all as specified and directed.

Use & waste of form work to the side of the column , rough finished flat surface area.complete all as specified and directed.

Use & waste of formwork to side and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, verhangs etc also plays between floors and beams etc.complete all as specified and directed.

Use & waste of formwork to edge of concrete flats, breks in flooors, openings in concrete walls , floors and roofs and sides of RCC/PCC bands in walls, horizontal or loppin and similar work all exceeding 20 cm wide(Where RCC/PCC band in walls spanning and opening , the formwork soffit only shall be paid for under item 7010 of SSR Part-II

S&F 10mm dia and over TMT bars as in reinforcement cut to length bent to shape etc as required incl binding with MS wire annealed not less than 0.90 m dia.complete all as specified and directed.

All as per Item No 19 above but 5 mm dia and over upto including 10 m dia in stirrups, spacers and binder etc.

M&L brick work using sub class B brick (old size) curved or straight in plan exc 6 mtr mean radius in cm (1:6).complete all as specified and directed.

M&L brick work using sub class ‘B’ bricks (old size) straight or curved on plan to any radius in half brick work built in CM 1:4 complete all as specified.

M&L 15 mm thick plastering on other than fair faces of wall surfaces in cm (1:6) complete all as specified and directed

M&L 5 mm thick plastering on ceilling concrete surface in cm (1:3) even and smooth without using extra cement.complete all as specified and directed.

M&L for sand filling under floor or in foundation,trenches including watering as required.complete all as specified and directed.

M&L for 75 mm thick cement concrete in sub base of floor in cement mortar (1:3:6) type C-2.complete all as specified and directed.

M&L for Polythene film,150 micron thick, laid on a coat of bitumen primer, @ 0.30 to .50 kg per sqm.complete all as specified and directed.

M&L for rendering 20mm thick in cement mortar 1:4 in two layers of 10mm each using WPC in finishing layer on brick or concrete surfaces finished even & smooth ( WPC for finishing layer will be measured and paid seperately as supply only).complete all as specified and directed.

Supply only integral water proofing compound.complete all as specified and directed.

M&L Hard core of gauge n exc 63 mm of broken boulder bellow plinth protection/hard standing/floor.complete all as specified and directed.

M&L PCC 1:3:6 type C-2 75 mm thick as in plinth protection even and smooth without using extra cement.complete all as specified and directed.

15 mm thick screed bed or bedding layer of mortar in CM 1:6 fixing of tiles in floor.complete all as specified and directed.

M&L 10 mm thick rendering in CM 1:4 on brick or concrete surfaces for fixing of tiles in wall.complete all as specified and directed.

M & L for Non - skid Ceramic tiles (joint free, coloured) 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

S&F for colour Glazed ceramic tiles 450x350mm of 7 to 8mm thick, in dado/skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match.complete all as specified and directed

S &F chequered cement concrete coloured tiles (glossy finish) 20cm x 20cm x 25 mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment complete all as specified and directed.

M & L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone match the shade of granite stone including grinding and polishing complete all as specified and directed .

Forming Constrution (Dummy) joints 30 mm deep x 10 mm wide, filled with sealing compound grade A.complete all as specified and directed

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of primer.complete all as specified and directed

M&L for preparation of new plastered surface of ceiling and applying three coats of white wash.complete all as specified and directed

M&L for preparation of new plastered surface of wall and applying three coats of white wash.complete all as specified and directed

S&F MS Hold fast confirming to Fe-290 Gde E-165.complete all as specified and directed

M&L PCC (1:3:6) type C-1 as in bed block of hold fast,coping using 20 mm stone agg steps etc.complete all as specified and directed

S&F Steel window side hung shutters including box type hinges with steel handle and steel pegs stay complete with glazing bars and fly proofing.complete all as specified and directed

S & F 3mm thick figured glass n exc 0.5 sqm in each pane glazing with oil putty.complete all as specified and directed

S&F 3 mm thick ordinary quality sheet glass in squares n exc 0.5 sqm in each pane glazing with oil putty.complete all as specified and directed

M&L for galvanised mild steel wire cloth of 0.56mm dia and average aparure of 1.4mm and fixed in position.complete all as specified and directed

S & F Pressed steel frames of size 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed.complete all as specified and directed

S&F 2nd class hard wood shutter 35mm thick plain framed, panalled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated.complete all as specified and directed

S/F 35mm thick glazed and skeleton shutters open rebated and prepared to receive glass gauge etc. Divided into squares with plain chamfered or rounded, rebated sash bars, sizes of the members of the shutters as specified in SSR Part I, section 8, clause 8.23(a).complete all as specified and directed

M&L for two coats of synthetic enamel painting to new wooden surfaces over a coat of pink primer including preparation of surfaces area exc 10cm width & girth.complete all as specified and directed

S&F 300 mm Aluminium alloy anodised sliding door bolt, plate type and fixing clip of sheet cast of extruded section and fixing bolt and sliding bolt of extruded section and fixed in position.complete all as specified and directed

S&F 200 mm aluminium anodised barrel tower bolt, of extruded section and fixed in position.complete all as specified and directed

M&L for extruded aluminium alloy handle fabricated type of 150 mm long.complete all as specified and directed

S&F 100 mm Butt hinges medium weight cold rolled mild steel and fixed.complete all as specified and directed

Preparation of concrete roof surfaces applying roof treatment as under:-(a) Applying bitumineous primer @ 0.30 litre per Sqm of surface (Shalitex Primer of STP Limited or equivalent as approved by GE (b) Applying coat of hot applied bitumen 85/25 @ 1.20 Kg/Sq m of surfaces (Make : STP Ltd or equivalent as approved by GE) (c) Laying of APP Modified water proofing membrance with non-woven polyster Reinforcement on hot applied bitumen with 100mm over lap at joints by torching on the transverse direction and 75 mm on longitudinal directional all as per manufacturer's instructions (Make : SUPER THERMOLAY OF STP LTD OR EQUIVALENT IWL/TEXSA) (c) Laying of APP Modified water proofing membrance with non-woven polyster Reinforcement on hot applied bitumen with 100mm over lap at joints by torching on the transverse direction and 75 mm on longitudinal directional all as per manufacturer's instructions (Make : SUPER THERMOLAY OF STP LTD OR EQUIVALENT IWL/TEXSA) (d) Applying a coat of bitumineous aluminium paint @ 0.10 litre/SM (Super Silver sheild of STP Ltd or equivalent as approved by GE)

M&L for 15 mm thick screed bed in cm 1:3 mixed with WPC as per manufactures instruction finished even and smooth over RCC roof slab without using extra cement (WPC shall be measured seperately).complete all as specified and directed

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length 140mm complete all as specified

S&F for MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified

S&F steel ventilator with top hung shutters including hinges with steel handle and steel peg stay with glazeing bars complete all as specified and directed

S & F Factory made solid panel pvc door shutter with chowkhats 30mm thick (style) consisting of frame made out of M.S.tubes for top & bottom rails.M.S.frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S.frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined to gether with solvent cement, suppling & fixing in the frame at site as per specification & drawing.complete all as specified and directed

S & F PVC door with chowkhats frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supply & fixing in opening as per specification & drawing.complete all as specified and directed

S & F vitreous china white wash hand basin flat back of size 550 x 400 mm including brackets CP waste coupling 32 mm and PVC waste pipe and 15mm PVC connection.complete all as specified and directed

S&F 500 Ltrs capacity rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position.complete all as specified and directed

S&F ball brass valve high pressure with polythene float & flynut screwed for iron pipe and fixed of size 20mm bore complete all as directed at site.complete all as specified and directed

S & F for 15 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

S/F vitreous china 580x440 mm,"ORISSA PATTERN" with 'P' or 'S' trap size squatting pan (Exclusive flushing cistern and flush pipe) incl foot rest complete and provision of lime concrete bedding complete all as specified and directed.

S & F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets , long bend including flush pipe of PVC 32mm dia and connection to pipes etc complete all as specified and directed .

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified.

S & F 15mm Angle Stop valves cast copper alloy,fancy type with chromium plated for iron pipe or for unions and fixed.complete all as specified and directed

S&F pillar taps, cast copper alloy , with capstan heads, fancy tupe, chromium plated , screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe , and fixed complete all as specified and directed.

S&F bib tap, chromium plated , fancy type, screwed for iron pipe or brass ferrule , 15 mm bore and fixed complete all as specified and directed.

S& F 75 mm dia PVC pipes single socketed in any length with rubber ring joints, laid in trenches/floors or fixed to wall complete all as specified and directed

S& F 110 mm dia PVC pipes single socketed in any length with rubber ring joints, laid in trenches/floors or fixed to wall complete all as specified and directed

S& F 75 mm dia PVC (SWR) bends any radius fixed in any position, complete all as specified and directed

S& F 110 mm dia PVC (SWR) bends any radius fixed in any position, complete all as specified and directed

S&F hand rails , half round or other steel section or core for wooden hand- rail straight portion, drilled and counter sunk for baluster running bars , for doors , balusters , nosing to steps including embedding in concrete and screwing etc wind ties for roof including securing bolts ; posts and struts in fencing including cutting tops to shape as directed , drilling holes , notching for wire , etc , flat iron fillets ( for securing wire mesh etc ) including all necessary drilling , bolting riveting etc and similar work confirming to Fe-290 Gde E-165 Complete all as specified and directed.

S&F Framed work such as door or gates of angle or other section, grills, gratings, etc, with ends of bars shouldered and/or riveted ,or forged into spikes, framed guard bars; barred iron doors, ladders;framed balusters; walk ways,railings, frameworks of water tanks and similar work including pintle hinges stops hand made sliding door bolts etc.complete all as specified and directed

Suply only chain link fencing 75x75x3.15mm, size to any type of standards, rails, straining bolts, etc incl provision of binding wire.complete all as specified and directed

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire.complete all as specified and directed.

S&F 10mm dia MS round bar fixed to chain link fening Top and bottom.complete all as specified and directed.

S&F 12 mm diaMild screw bolts machine made) with hexagonal or square heads at one end and screwed the other, or screwed on both ends each screwed end to be fitted with washers and one hexagonal or square nut but length of bolt exc 10cm but n exc 15cm long.complete all as specified and directed.

Preparation of new steel surfaces exc 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed.

Preparation of newly steel surfaces n'exc10cm width or grith and applying two coats of synthatic enamel paint over red oxide primer.complete all as specified and directed

Taking out 150 mm bore GI/CI Water main from trenches and staking at site complete all as directed.

Taking out 100 mm bore GI/CI Water main from trenches and staking at site complete all as directed.

Supply and fix pipes MS ERW including specials supplied and laid in wall/trench complete nominal dia 80 mm as per IS 3589 (1981) thickness 6.0 mm inclduing welding for desire shape for fitting complete all as speified and directed.

Supply, laying and testing ductile iron pressure pipe socket and spigot end, class K-7, confirming to IS-8329/2000 blast furnace slag cement with portland cement properties suitable for Push - on- joint with inside cement mortar lining, internal metallic zinc coationg and external black bitumen coating of size 150 mm dia duly ISI marked laid in trenches etc complete all as specified and directed.

Supply, laying and testing ductile iron pressure pipe socket and spigot end, class K-7, confirming to IS-8329/2000 blast furnace slag cement with portland cement properties suitable for Push - on- joint with inside cement mortar lining, internal metallic zinc coationg and external black bitumen coating of size 100 mm dia duly ISI marked laid in trenches etc complete all as specified and directed.

Taking out 80 mm GI Water main from trenches/wall/ceilings/floor and staking at site complete all as specified and directed

Taking out 50 mm GI Water main from trenches/wall/ceilings/floor and staking at site complete all as directed.

Taking out 25 mm GI Water main from trenches/wall/ceilings/floor and staking at site complete all as specified and directed

Taking out 20 mm GI Water main from trenches/wall/ceilings/floor and staking at site complete all as specified and directed

Taking out 15 mm GI Water main from trenches/wall/ceilings/floor and staking at site complete all as directed.

S&F steel tubes medium grade galvanised 20 mm bore with all fittings and fixed complete to walls and ceilings and laid in floors complete all as directed.

S&F steel tubes medium grade galvanised 15 mm bore with all fittings and fixed complete to walls and ceilings and laid in floors complete all as directed.

S&F 40mm bore medium grade galvanished tube with all fitting & fixed complete to walls or ceiling & laid in floors.complete all as specified and directed

S&F steel tubes medium grade galvanised 80 mm bore with all fittings laid in trenches complete all as directed.

Supply and laying 3 layered (outer green coloured UV stabilized, middle black coloured UV stabilized and inner most layer white coloured with antimicrobial properly) fusion welder PP-R (Poly proplene randon Co-polymer) pipes laid in trenches incl plain PP-R and brass threaded PP-R fittings or flanged joints incl connecting up with existing system of grade PN 10, SDR-11 of 90 mm outer dia size complete all as specified and directed.

Supply and laying 3 layered (outer green coloured UV stabilized, middle black coloured UV stabilized and inner most layer white coloured with antimicrobial properly) fusion welder PP-R (Poly proplene randon Co-polymer) pipes laid in trenches incl plain PP-R and brass threaded PP-R fittings or flanged joints incl connecting up with existing system of grade PN 10, SDR-11 of 63 mm outer dia size complete all as specified and directed.

Supply and laying 3 layered (outer green coloured UV stabilized, middle black coloured UV stabilized and inner most layer white coloured with antimicrobial properly) fusion welder PP-R (Poly proplene randon Co-polymer) pipes laid in trenches incl plain PP-R and brass threaded PP-R fittings or flanged joints incl connecting up with existing system of grade PN 10, SDR-11 of 32 mm outer dia size complete all as specified and directed.

Supply and fix cast iron foot valve 80 mm dia screwed type ISI marked, as per IS 4018, including necessary rubber gasket, nut bolt,and taking out the unserviceable foot valve complete all as directed.

Supply and fix in repair non return valve 80 mm dia screwed type ISI marked, including jointing materials complete all as directed.

S&F in repair PP-R gate valve (Brass insert) as per requirement of site and fixed of 63 mm bore complete all as specified and diretected.

S&F Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed 20 mm bore complete all as specified and directed.

S&F Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed 15 mm bore complete all as specified and directed.

S&F in repair of sluice valve (heavy duty) with SS spindle H/W conforming to IS 14846 both end flanged class PN 1.6 of size 150 mm dia incl necessary nuts,bolts washers and gasket including taking down all as specified and directed.(Make:Kirloskar/Leader/Zoloto/Audco/Venus/Upadhyaya).

S&F in repair of sluice valve (heavy duty) with SS spindle H/W conforming to IS 14846 both end flanged class PN 1.6 of size 100 mm dia incl necessary nuts,bolts washers and gasket including taking down all as specified and directed.(Make:Kirloskar/Leader/Zoloto/Audco/Venus/Upadhyaya).

Supply and Fix sluice valve of size 80 mm dia bore flanged ends drilled type with gun metal spindle incl nut and bolts washer and jointing material complete all as specified of class PN-I.6 ISI marked complete all as specified and directed. (Make:Kirloskar/Leader/Zoloto/Audco/Venus/Upadhyaya).

M&L for DI fittings for spigot and socket pipes of size 100 mm to 350 mm bore such as bends(any type,radius and angle) tapers any type (straight, bend, increasing,decreasing or double socket etc) Tee pieces single branch, 'Y' junction, double branch, cross(all sockets or socket and spigot) collars caps and plugs complete all as specified and directed.

M&L for construction of valve pit of size 0.9 x 0.9 x 0.9 m (internal diamention) one brick thick wall including MS sheet cover made of MS sheet 3 mm thick and 50 x 50 x 6 mm thick MS angle iron frame and locking arrangement and painting with two coats of synthetic enamel paint over a coat of red oxide primer after preparation of surfaces including demolition of existing brick masonry valve pit complete all as specified and directed.

M&L for construction of valve pit of size 0.6 x 0.6 x 0.6 m (internal diamention) one brick thick wall including MS sheet cover made of MS sheet 3 mm thick and 50 x 50 x 6 mm thick MS angle iron frame and locking arrangement and painting with two coats of synthetic enamel paint over a coat of red oxide primer after preparation of surfaces including demolition of existing brick masonry valve pit complete all as specified and directed.

M & L for point wiring one light/fan point/call bell controlled by one way switch. with 1.5 Sq mm (nominal area) PVC insulated and unsheathed single core FRLSH copper cable 1100 volts grade with multi-stranded copper conductor in and including PVC concealed conduit and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and unsheathed single core FRLSH cable 1100 votls grade with stranded copper conductor and connected to common earth dolly complete for housing the switches, socket outlets, fan regulators etc. for the following (Rate deemed to be inclusive of cutting chases and making good disturbed surface).

All as per Item No 115 but one socket outlet 5 pin 6 amps on independent board.

All as per Item No 115 but one 5 amps socket outlet on same board with other switch.

M & L for point wiring with 2.5 Sq mm (nominal area) PVC insulated and unsheathed single core FRLSH copper cable 1100 volts grade with multi-stranded copper conductor in and including PVC concealed conduit and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and unsheathed single core FRLSH cable 1100 votls grade with stranded copper conductor and connected to common earth dolly, with and including 1.6 mm thick cadmium plated sunk MS pressed steel terminal box fixed with brass screws complete for one socket outlet 6 pin 15/16 amps on independent board (Rate deemed to be inclusive of cutting chases and making good disturbed surface).

Supply and fix Modular switch one way 10 Amp.

Supply and fix modular socket outlet 2 in 1, 3 pin 10 A.

Supply and fix modular socket outlet 2 in 1, 3 pin 20 Amps

Supply and fix Modular switch one way 20 Amp.

Material and labour for ceiling rose polycarbonate isolated body 3 ways terminals.

Supply and fix modular type electronic fan regulator.

Supply and fixing modular white cover plate with frame 3 modules complete all as specified and as directed.

Supply and fixing modular white cover plate with frame 8 modules complete all as specified and as directed.

Supply and fixing modular metal flush box 3 modules complete all as specified and as directed.

Supply and fixing modular metal flush box 8 modules complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 220 CMM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) all as specified and directed.Make: Usha model No. 1200 mm techoair BLDC 5 Star or equivalent make in Crampton/Havells/Orient/Bajaj

M&L for Brick Sub Class 'B' locally available best quality laid in trenches with width equal to length of the bricks, above sand cushioning for cable protection complete all as specified and as directed.

S&F in replacement steel water tubing 50 mm dia of bore light grade galvanised with all fittings laid in trenches / fixing with surface of wall after drawn through electric cable by means of nuts bolt and washers all as directed .

Supply,laying in repair in trenches of XLPE UG cable insulated aluminium stranded conductor served with an inner sheathing or PVC tape heavy duty armoured upto 1100volts (earthed) GI steeel strip and overall PVC sheathed nominal cross sectional area 35 sqmm 4 core and testing complete all as specified and directed.

Material & Labour for earthing with galvanised steel earth plate electrode of size 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts check nuts and washers of galvanised iron or steel using GI strip 32x6mm as earthing lead as shown in electrical plate No. 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:3:6 type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI light grade watering pipe, 40mm dia GI light grade earth lead protection pipe, CI frame and cover, wire, copper lugs etc mesh, chorcoal and common salt in alternatee layer complete all as specified and directed by Engr-in-Charge.

M & L for point wiring with 2.5 Sq mm (nominal area) PVC insulated and unsheathed single core FR copper cable 1100 volts grade with multi-stranded copper conductor in and including Casing capping and accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and unsheathed single core FR cable 1100 votls grade with stranded copper conductor and connected to common earth dolly complete for one socket outlet 6 pin 15/16 amps on independent board.

M&L for fixing of Switch Socket Combination 5/16 Amps,5 in 1 flush type inclduing pvc box of size 4x7 inch for munting all as specified and directed..

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe complete all as directed. Make-Havells,Cat No-GHWAMGTWH025 or equivalent make of BAJAJ/Crompton/USHA.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB SP) of single poles and 6-32 Amp current carrying capacity in the MCB DB complete with connection testing and commissioning all as specified and directed.

Supply and fixing stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle suitable for GI tubing 15 mm dia all as specified and directed.

S&F Bib tap chromium plated 15 mm dia suitable for water cooler all as specified and directed. Note 1:-The contract sum shall be arrieved at after deducting amount of schedule of credit from the total quated amount. Note 2-Contractor's supervisor and main worker would wear shirt/T-shirt of colour sky blue/brown/yellow preferable embosed with contractor's firm name while carriying out any activities in defence area for better check of security purpose. Note 3:-The tenderer (all eligible contractors) shall ascertain the taxes & levies as on date. The subject tender caters all the taxes & levies as on date including the latest notification of GST issued as on date ( issued by Central Board of Indirect Taxes and Customs)

M/s Brahamaputra Wood Industries

North Eastern Builders

M/S MOHANPASARI

M/S KAUSHICK CONSTRUCTION

sanjay upadhya

M/S Jiban Krishan Das and Co