Development of District Hospital Chengannur in Alappuzha District

Amount

CIVIL WORK SUB STRUCTURE

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.7.1 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Ordinary rock

2.7.3 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Hard rock (blasting prohibited

2.31 : Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.33.2 : Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyound 60 cm girth up to and including 120 cm girth

50.2.3.1 : Pumping or Bailing out water and removing slush etc by using pump set including cost of labour, oil hire charges of pumpset, etc complete

20.2A.1 : Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used.600 mm dia piles

20.2A.3 : 1000 mm dia piles

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

2.35.3.1 : Diluting and injecting chemical emulsion for POST -CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion):Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

60.65 : Providing Z steel sheet pile of size 400x185x7.5/8.5 driving down vertically in lines and levels interlocking with adjacent piles with suitable pile driving unit and all accessories including all labour hire charges etc. complete and as per the directions of departmental officers at site.

22.4.1 : Providing and Placing in position suitable PVC water stops conforming to IS : 12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:Serrated with central bulb ( 225 mm wide, 8-11 mm thick)

od109065/2019_2020 : Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used.700 mm dia pile

od109066/2019_2020 : Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used . 900 mm dia piles

od110925/2019_2020 : Extra for additional lead upto 1Km or initial lead of 50M for disposing surplus excavated earth as per the direction of engineer in charge

od130526/2019_2020 : Extra for additional lead for every 1Km above 1Km upto 5 Km

od130535/2019_2020 : Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer incharge. Single pile 500 tonne Safe capacity Routine test Load 1.5 times the Safe capacity) For 900mm Pile

od130536/2019_2020 : Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer incharge. Single from 750 MT to 1000 MT Safe capacity Initial test (Test Load 2.5 times the Safe capacity) For 900mm

od144184/2019_2020 : Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer incharge. Single pile 250 tonne Safe capacity Routine test Load 1.5 times the Safe capacity)-700mm dia pile

22.22 : Providing and mixing integral crystalline admixture for waterproofing treatment toRCC structures like basement raft, retaining walls, reservior, sewage & watertreatment plant, tunnels / subway and bridge deck etc.. at the time of transportingof concrete into the drum of the ready-mix truck , using integral crystalline [email protected]% (minimum) to the weight of cement content per cubic meter of concrete)or higher as recommended by the manufacturer's specification in reinforced cementconcrete at site of work. The material shall meet the requirements as specified inACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90%,compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostaticpressure. The crystalline admixture shall be capable of self-healing of cracks up toa width of 0.50mm. The work shall be carried out all complete as per specificationand the direction of the Engineer-in-charge. The product performance shall carryguarantee for 10 years against any leakage.

od136249/2019_2020 : "Supply and installing waterproofing treatment for Raft Slab using HDPE ""pre applied Membrane , ( installed by manufacturer's approved applicator) a 1.2 mm thick fully bonded HDPE sheet membrane below the raft, above PCC, Membrane shall be installed in strict accordance with the manufacturer's instructions and shall provide an intimate bond to resist water migration. The fully bonded HDPE sheet membane shall consists of a multi layer composite filim which cosists of highly resilient HDPE filim, self adhesive polymer layer and a trafficable particulate layer. The fully bonded HDPE sheet water proofing membrane shall have following typical properties:<br>1) Colour- White 2) Hydrostatic Head Resistance at laps - 70m head of water as per ASTM D5385; 3) Water migration Resistance: 70m head of water as per ASTM D5385; 4) Elongation- 400% 5) Peel adhesion to concrete: >550N/m (ASTM D 903 Modified) 6) Low Temp Flexibility: -25 deg C, pass (ASTM D 1970) 7) Puncture Resistance -800N (as per ASTM E154) Membrane shall be installed with standard 100mm slevedge laps, and end executed with Fixer, applied as per manufacturer's instructions. Membrane shall be laid over the entire area and returned on to a vertical slab formwork. Hot applied materials or protective screed shall not be permitted. All systems to be installed as per manufacturer's recommendations etc. complete with all lead and lift for all materials and labour and as directed by engineer in - charge.

CIVIL WORK-SUPER STRUCTURE

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.38 : Extra for R.C.C. /B.M.C/R.M.C. work above floor V level for each four floors or part thereof.

4.3.2 : Centering and shuttering including strutting, propping etc. and removal of form work for:Retaining walls, return walls, (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.11.1 : Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.5 : Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.1.6 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level thickness 20cm and above in : CM 1:6 ( 1 cement : 6 coarse sand sand) etc complete

6.5 : Extra for brick work/ AAC block masonry/Tile brick masonry in super structure above floor V level, for each four floors or part thereof by mechanical means.

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

6.47 : Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor Vlevel with RCC band at sill level and lintel level with approved block laying polymermodified adhesive mortar all complete as per direction of Engineer-in-Charge. (Thepayment of RCC band and reinforcement shall be made for seperately).

CIVIL WORK-FINISHING

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

5.23 : Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 ( cement : 3 fine sand).

13.11 : 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 ( 1 cement : 6 fine sand).

13.22 : Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

od110072/2019_2020 : Painting with microbial paint the inside walls with approved quality two or more coats to smooth even finish on ceiling and walls including cost and conveyance of all materials to site, labour charges, hire charges for scaffolding, etc as directed by Engineer-in-Charge at all levels

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.62.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

12.45.4 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:Fully Perforated Gypusm Plaster Board of size 1200 x 2400 x 12.5 mm having approx. 15% perforated area with perforation size and pattern as approved by the Engineer - in- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60.

12.53 : Providing and Fixing 15 mm densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture spintone /cosmos /Hexa or equivalent of size 595x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main 'T' of size 24 x 28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24x28 mm made of 0.33 mm thick (minimum) sheet to be inter locked at middle of the 1200x600 mm panel to from grid of size 600x600 mm, resting on periphery walls/partitions on a Perimeter wall angle pre-coated steel of size (24x24x3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture (Spintone / Cosmos/hexa) in the grid, including cutting / making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever require. Main 'T' runners to be suspended from ceiling using G.I slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size of 85x30x0.8 mm, spaced at 1200mm centre to centre along main 'T' bottom exposed with 24 mm of all T- sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by by engineer-in-charge. Note:- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm. The calcium silicate ceiling tiles shall have NRC. value of 0.50 (Minimum), light reflection > 85% non - combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity < 0.043 w/m 0 KC.

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.12.2.5 : Providing & fixing Poly carbonate multi wall plain sheet 8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/ self tapping screw of size ( 5.5x55mm) with EPDM seal complete upto any pitch in horizontal /vertical / curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size and shapes where ever required.

od144619/2019_2020 : Providing &amp; fixing Poly carbonate solid wall plain(glass type) sheet 6 mm thick with UV protected on two side as approved by the Engineer in charge and should be supplied in a size of 2.44x1.22m as decide by the Engineer in charge. The sheets shall be fixed using self drilling/ self tapping screw of size (5.5x55mm) with EPDM seal and aluminium H/T frame etc complete upto any pitch in horizontal / vertical / curved surfaces, but excluding the cost of purlins, rafters, trusses and including cutting to size and shapes where ever required.&nbsp;

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.47.2 : Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm

11.37A : Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS :15622 (thickness to be specified by the manufacturer ) of approved make in allcolours, shades except burgundy, bottle green, black of any size as approvedby Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thickbed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cementslurry @ 3.3kg per sqm including pointing in white cement mixed with pigmentof matching shade complete.

11.36 : Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

11.4 : 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete

10.15.1 : Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular /L-Type sections, made of 1.60 mm thick M.S. Sheet,joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 ( 1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

8.9.1.2 : Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.Granite of any colour and shade

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.3.2 : Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

8.13.1 : Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye orequivalent.

8.3.1 : Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Marble work

11.19.4 : Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand):Ordinary cement without any pigment

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

22.6 : Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. laying second layer of fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tilling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured)

21.18 : Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)

9.165.1 : Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

9.100.1 : Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:125 mm

9.71.1 : Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:125x64x2.50 mm

9.74.2 : Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:200x10 mm

9.82 : Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

9.84 : Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

9.103 : Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS: 1868) aluminium lever handles of approved quality with necessary screws etc . complete.

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

9.117.1 : Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1 mm), with wall thickness 2.0mm (±0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer-in-chargeExtruded section profile size 48x40 mm

9.118.2 : Providing and fixing to existing door frames30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge.

21.4.1 : Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer -in- Charge.With stainless steel cover plate minimum 1.25 mm thickness

21.2.2 : Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

9.12 : Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. ( Area of opening for glass panes excluding portion inside rebate shall be measured).

21.3.2 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

5.30 : Add for plaster drip course / groove in plastered surface or moulding to R.C.C. projections.

od110926/2019_2020 : Supply and providing Wooden Celing with 16mm marine plywood, 4mm Vineer board including Cutting , Fitting and polishiing with all necessary fittings

od110927/2019_2020 : Lead glass viewing panel of size 60x50cm 2.5mm Pb

od110928/2019_2020 : Radiation Safety Lead Lined Doors For Hospital, Rust proof and Zinc Polished of size 1.5 x 2.4. The door should have sandwich lead of 2.5 Pb equivalent. This door should have heavy duty hinges to support the weight of the door with lead, This door will be fixed with suitable door frame that does not permit any radiation leakage. There should not be any leak between the door and the door frame. This door can be fixed in CT scan and Digital X ray room. Lead glass Manufactures certification on Lead thickness should be produced.

od110929/2019_2020 : Hand rail:&lt;br&gt;Providing and Fixing of 159mm High Acrylic Handrail with an aluminium thickness of 1.4mm and pvc thickness of 2mm

od110930/2019_2020 : Providing cement concrete screeding M25 using 12mm aggregate(RMC) for basement 5cm thick after appliying bonding agent on concrete floor before pouring concrete adding non metalic hardner at 3kg/m2 during power trovelling leveling with power prowel machine cutting grooves maximum 16m2 2cm to 2.5cm deep avoid expansion cracks and filling the grooves with epoxy including cost and convience of all materials and labour charges etc complete.

od110931/2019_2020 : Extra for VDC with same specification of screeding M25

od110932/2019_2020 : 16mm Multi wood Doors and Shelf With PU finish paint on outter face with all necessary fitting including SS door handles and hinges as required by engineers incharge

od110933/2019_2020 : Supply and providing Wooden Celing with 16mm marine plywood, 4mm Vineer board including Cutting , Fitting and polishiing including CNC Cutting as required with all necessary fittings

od134744/2019_2020 : Providing and fixing SS lock of size suitable for glass door with SS screws etc. complete as per direction of Engineer-in-Charge.

od134745/2019_2020 : Providing and fixing SS H handle of size with SS screws etc. complete as per direction of Engineer-in-Charge.

CIVIL-EXTERNAL WORK

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.7.3 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Hard rock (blasting prohibited

51.2.3 : Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

51.2.4 : Filling with Sand Supplying and filling sand in foundation trenches of culvert for stabilizing the top clay layer including watering, ramming, consolidating and dressing, etc complete for improving bearing capacity of soil.

65.25 : Supplying granite quarry run from approved quarry to sorting site by lorry/ tipper, and sorting the stones into 5 kg to 10 kg category stones of approved quality with specific gravity ranging from 2.65 to 2.8 for forming the filter layer of breakwater inclusive of cost of stones, hire of lorries and machineries, labour charges required at quarry and at sorting place and the measurements of categorized stones after proper sorting are taken on weigh bridge installed at site at the cost of the contractor with approved software having printouts using contractors supplied papers, stationeries and conveyed to the approved alignment of the breakwater including conveyance from sorting platform and dumping stones using tippler (3.5x2.5 sqm size) or any suitable methods installed at site on a moving crane having a capaciaty of not less than 20T and placing the stones at sea bed in uniform layer of design thickness for forming filter layer of breakwater as per the approved drawing and design and inspecting the profile once in a week including hire and operational charges of T & P, tippler, crane and all incidental charges etc. complete as per the direction of departmental officers at site. <br> Alappuzha District

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.5 : Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

22.6 : Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. laying second layer of fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tilling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured)

13.7.2 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:4 ( 1 cement : 4 fine sand)

5.23 : Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 ( cement : 3 fine sand).

13.11 : 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 ( 1 cement : 6 fine sand).

13.37.1 : White washing with lime to give an even shade:New work (three or more coats)

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.48.1 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.62.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

10.6.1 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.9 : Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer -in-Charges, (area of grill to be measured).

10.7 : Providing and fixing ball bearing for rolling shutters.

21.3.2 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.47.2 : Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm

11.36 : Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.3.2 : Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

17.10.1.1 : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board510x1040 mm bowl depth 250 mm

17.7.2 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brass pillar tap

18.8.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes

18.52.1 : Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

50.18.7.6.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10 Kfg/cm - Internal work- Exposed on wall

50.18.9.8.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2

18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

19.7.1.1 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.20 : Supplying and fixing C.I cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg

30.2.33 : Providing and fixing Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and even, watering with sprinkler

16.69 : Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

16.91.1 : Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.60mm thick cement concrete paver block of M-35 grade with approved colour, design& pattern.

16.68 : Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

10.25.2 : Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

10.15.1 : Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular /L-Type sections, made of 1.60 mm thick M.S. Sheet,joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 ( 1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

10.26.1 : Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.M.S. tube

13.48.3 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture

12.50 : Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.51.1 : Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete:Ridges plain (500-600 mm)

25.7 : Designing, fabricating, testing, installing and fixing in position Curtain Wall withAluminium Composite Panel Cladding, with open grooves for linear as well ascurvilinear portions of the building , for all heights and all levels etc. including:a) Structural analysis & design and preparation of shop drawings for pressureequalisation or rain screen principle as required, proper drainage of water to makeit watertight including checking of all the structural and functional design.b) Providing, fabricating and supplying and fixing panels of aluminium compositepanel cladding in pan shape in metalic colour of approved shades made out of4mm thick aluminium composite panel material consisting of 3mm thick FR grademineral core sandwiched between two Alumini um sheets (each0.5mm thick). Thealuminium composite panel cladding sheet shall be coil coated, with Kynar500based PVDF / Lumiflon based fluoropolymer resin coating of approved colourand shade on face # 1 and polymer (Service) coating on face # 2 as specified usingstainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backerrods etc.c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanisedwith serrations and serrated washers to arrest the wind load movement, fasteners,SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators toprevent bi-metallic contacts all complete required to perform as per specificationand drawing The item includes cost of all material & labour component, the cost ofall mock ups at site, cost of all samples of the individual components for testing inan approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wallwith aluminium composite panel cladding till the handing over of the building foroccupation. Base frame work for ACP cladding is payable under the relevantaluminium item.s The Contractor shall provide curtain wall with aluminiumcomposite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item description, as specified, as per theapproved shop drawings and as directed by the Engineer-in-Charge.However, for the purpose of payment, only the actual area on the external face ofthe curtain wall with Aluminum Composite Panel Cladding (including width ofgroove) shall be measured in sqm. up to two decimal places.

16.59.1 : Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC: 67- 2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x 5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours). Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-Charge.Mandatory / Regulatory sign boards of 900 mm diametre with support length of 3750 mm

16.59.2 : Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC: 67- 2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x 5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours). Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-Charge.Cautionary / warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm

16.62 : Providing and applying 2.5 mm thick road marking strips ( retro - reflective ) of specified shade / colour using hot thermoplastic material by fully / semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T & P, cleaning the road surface of all dirt, seals, oil grease and foreign material etc. complete as per direction of Engineer - incharge and accordance with applicable specifications .

19.6.2 : Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand) including testing of joints etc. complete:150 mm dia R.C.C. pipe

19.6.4 : Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand) including testing of joints etc. complete:300 mm dia R.C.C. pipe

16.65 : Providing and fixing post delineators made of ABS round body fitted with 2 nos 100 mm dia high reflective reflectors and mounted on MS pipe of 65 mm dia duly powder coated anti-rust and anti theft steel to be installed as per direction of Engineer-in-Charge.

30.2.15.1 : Half brick circular tree guard in bricks, internal diameter 1.25 metre and height 1.2 metre above ground and 0.20 m below ground, bottom two courses laid dry and top three courses in cement mortar 1:6 (1 cement : 6 fine sand) and the intermediate courses being in dry honey comb masonry as per design complete:With common burnt clay F.P.S. (non modular) bricks of class designation 5

30.2.50 : Providing & fixing of White River (Stone) Pables size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge.

30.2.57.1 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material?s as per direction of officer in charge (excluding cast of plant & water )Cost of plantation per trees plants (for 100 nos.=427.45/100)

od110924/2019_2020 : Providing and fixing floor drain with cockroach trap (multi trap) conceled or exposed , SS304 grade floor grating with cup including cost and conveyance of all material , labour charges, sundries etc complete as directed by the engineer-in-charge at all levels

25.2 : Designing, fabricating, testing, protection, installing and fixing in position semi(grid) unitized system of structural glazing (with open joints) for linear as well ascurvilinear portions of the building for all heights and all levels, including:a) Structural analysis & design and preparation of shop drawings for the specifieddesign loads conforming to IS 875 part III (the system must passed the proof testat 1.5 times design wind pressure without any failure), including functional designof the aluminum sections for fixing glazing panels of various thicknesses, aluminiumcleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clampsetc., structural and weather silicone sealants, flashings, fire stop (barrier)-cumsmokeseals, microwave cured EPDM gaskets for water tightness, pressureequalisation & drainage and protection against fire hazard including:b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3Dimentional movement for achieving perfect verticality and fixing structural glazingsystem rigidly to the RCC/ masonry/structural steel framework of building structureusing stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetalliccontacts with nuts and washers etc. of stainless steel grade 316, of the requiredcapacity and in required numbers.c) Providing and filling, two part pump filled, structural silicone sealant and onepart weather silicone sealant compatible with the structural silicone sealant ofrequired bite size in a clean and controlled factory / work shop environment ,including double sided spacer tape, setting blocks and backer rod, all of approvedgrade, brand and manufacture, as per the approved sealant design, within and allaround the perimeter for holding glass.d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thickand of sizes, shapes and profiles, as required as per the site conditions, to seal thegap between the building structure and all its interfaces with curtain glazing tomake it watertight.e) Making provision for drainage of moisture/ water that enters the curtain glazingsystem to make it watertight, by incorporating principles of pressure equalization,providing suitable gutter profiles at bottom (if required), making necessary holesof required sizes and of required numbers etc. complete. This item includes costof all inputs of designing, labour for fabricating and installation of aluminium grid,installation of glazed units, T&P, scaffolding and other incidental charges includingwastages etc., enabling temporary structures and services, cranes or cradles etc.as described above and as specified. The item includes the cost of getting all thestructural and functional design including shop drawings checked by a structuraldesigner, dully approved by Engineer-in-charge.The item also includes the cost of all mock ups at site, cost of all samples of theindividual components for testing in an approved laboratory, field tests on theassembled working structural glazing as specified, cleaning and protection till thehanding over of the building for occupation. In the end, the Contractor shall providea water tight structural glazing having all the performance characteristics etc. allcomplete as required, as per the Architectural drawings, as per item description,as specified, as per the approved shop drawings and as directed by the Engineerin-Charge.Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extrudedaluminium section capping for fixing in the grooves of the curtain glazing andvermin proof stainless steel wire mesh shall be paid for separately under relevantitems under this sub-head. However, for the purpose of payment, only the actualarea of structural glazing (including width of grooves ) on the external face shallbe measured in sqm. up to two decimal places.Note:-2. The following performance test are to be conducted on structural glazingsystem if area of structural glazing exceeds 2500 Sqm from the certified laboratoriesaccreditated by NABL(National Accreditation Board for Testing and CalibrationLaboratories), Department of Science & Technologies, India. Cost of testing ispayable separately. The NIT approving authority will decide the necessity of testingon the basis of cost of the work, cost of the test and importance of the work.Performance Testing of Structural glazing systemTests to be conducted in the NBL Certified laboratories1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to+300pa) as perASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr”2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testingmethod for a range up to 2000 ml.”3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01-05 testingmethod for a range upto 2000 ml”4. Structural Performance Deflection and deformation by static air pressure test(1.5 times desing wind pressure without any failure) as per ASTME-330-10 testingmethod for a range upto 50 mm”5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method forQualitative test” Tests to be conducted on site6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi)upto 2000ml”

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

PLUMBING

od107196/2019_2020 Supply, installation, testing and commissioning of solar water heating system of 9000L/day using flat plate collectors - 50 panels with forced circulation pump, 2 nos of MS insulated storage tank of 4500L capacity each and heat pumps 2 nos each of capacity 500L/hr/18kw for back up and recirculation pump of 5000L/hr @ 20m head. The system shall be complete in all respects using necessary CPVC pipes, brass isolation valves, temperature sensors, timer, non return valves and other accessories complete. An electric control panel shall be provided for automation of the entire system.

od107197/2019_2020 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SCH 40) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work - Exposed on wall (for pumping main)<br>65 mm nominal dia Pipes

od107198/2019_2020 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SCH40) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work - Exposed on wall (For pumping main)<br>80 mm nominal dia Pipes

od107199/2019_2020 Supply, testing and commissioning of Bore well submersible pump of capacity to deliver 50 lpm at 180m head (Depth of bore well considered is 500ft) with motor starter, cable, copper earthing wire etc. to enable the pump fully functional. (approximately 4HP, filling time 11hrs)

od107200/2019_2020 Supply,Erection, Testing and Commissioning of Non Clog submersible pump (Dewatering pump) sets capable of lifting 200lpm of water against a total head of 20m with accessories such as non return valve, full way wheel valve, starter, MCB, voltmeter and ammeter, panel board etc.(approximately 1HP) (1 working)

od107201/2019_2020 Supply,Erection, Testing and Commissioning of Centrifugal pump (Transfer pump) set capable of lifting 333 lpm of water against a total head of 50m with accessories such as non return valve, full way wheel valve, starter, MCB, voltmeter and ammeter, Indicating lamps, panel board for operation of pumps, dry run preventer, Foot valve etc.(approximately 7.5HP, filling time 45 min) (1 working and other standby) (for STP treated water)<br>Make

od107202/2019_2020 Supply,Erection, Testing and Commissioning of Centrifugal pump (Transfer pump) set capable of lifting 333 lpm of water against a total head of 50m with accessories such as non return valve, full way wheel valve, starter, MCB, voltmeter and ammeter, Indicating lamps, panel board for alternate operation of pumps, dry run preventer, Foot valve etc.(approximately 7.5HP, filling time 30min) (1 working and other standby) (for Flushing water)

od107203/2019_2020 Supply and Laying UPVC SWR Type B pipes as per IS 13592, lowering into trenches, placing in position, aligning to line and levels and jointing with solvent cement including earth work excavation in all classes of soil, refilling the trenches and transporting excess soil as recommended by the site engineer, complete. : 200 mm diameter (For sewer lines).

od107204/2019_2020 Supply and Laying UPVC SWR Type B pipes as per IS 13592, lowering into trenches, placing in position, aligning to line and levels and jointing with solvent cement including earth work excavation in all classes of soil, refilling the trenches and transporting excess soil as recommended by the site engineer, complete. : 160 mm diameter (For sewer lines).

od107205/2019_2020 110 mm PVC SWR Type B in trenchesSupply and Laying UPVC SWR Type B pipes as per IS 13592, lowering into trenches, placing in position, aligning to line and levels and jointing with solvent cement including earth work excavation in all classes of soil, refilling the trenches and transporting excess soil as recommended by the site engineer, complete. : 110 mm diameter (For sewer lines).

od107206/2019_2020 Supply and fixing inline rain water filter with ss304 screen with 110mm inlet and 90mm drain outlet

od107207/2019_2020 Constructing masonry shoe to the bottom of the rain water pipes with brick in cement mortar 1:6 over CC 1:4:8 using 40mm metal concrete, plastering the exposed surfaces using CM 1:5 one coat, forming the circular spout outlet, finishing etc. complete.

od107208/2019_2020 Supply , jointing and fixing UPVC SWR Type A pipes as per IS 13592 exposed pipes and specials for vent with good quality solvent cement and teflon tape and fixing the same to line, plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by using slotted rails , U clamps, 8mm threaded rods and other required materials including drilling holes, making good the walls, cleaning etc. and finishing complete : 75 mm diameter

od107209/2019_2020 Supply , jointing and fixing UPVC SWR Type A pipes as per IS 13592 exposed pipes and specials for Rain water with good quality solvent cement and teflon tape and fixing the same to line, plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by using slotted rails , U clamps, 8mm threaded rods and other required materials including drilling holes, making good the walls, cleaning etc. and finishing complete. : 110 mm diameter

od107210/2019_2020 Supply , jointing and fixing UPVC SWR Type A pipes as per IS 13592 exposed pipes and specials for Rain water with good quality solvent cement and teflon tape and fixing the same to line, plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by using slotted rails , U clamps, 8mm threaded rods and other required materials including drilling holes, making good the walls, cleaning etc. and finishing complete. : 160 mm diameter

od107211/2019_2020 Supply and Fixing PVC Ventilation Cowl with wired mesh in position. : 75 mm diameter

od107212/2019_2020 Supply , jointing and fixing UPVC SWR Type A pipes as per IS 13592 exposed pipes and specials for Rain water with good quality solvent cement and teflon tape and fixing the same to line, plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by using slotted rails , U clamps, 8mm threaded rods and other required materials including drilling holes, making good the walls, cleaning etc. and finishing complete. : 75 mm diameter

od107213/2019_2020 Supply , jointing and fixing UPVC SWR Type B pipes as per IS 13592 Sanitary exposed pipes and specials with good quality solvent cement and teflon tape and fixing the same to line, plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by using slotted rails , U clamps, 8mm threaded rods and other required materials including drilling holes, making good the walls, cleaning etc. and finishing complete : 75 mm diameter

od107214/2019_2020 Supply , jointing and fixing UPVC SWR Type B pipes as per IS 13592 Sanitary exposed pipes and specials with good quality solvent cement and teflon tape and fixing the same to line, plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by using slotted rails , U clamps, 8mm threaded rods and other required materials including drilling holes, making good the walls, cleaning etc. and finishing complete : 110 mm diameter

od107215/2019_2020 Supplying and fixing PVC Floor Trap 100mmx75mm size without Jali including cutting open, boring through RCC slabs and making good the damages.

od107216/2019_2020 Providing and fixing Brass dynamic flow automatic balancing valve of approved quality (screwed end) in hot water supply: 20mm Dia

od107217/2019_2020 Providing and fixing gun metal non- return valve of approved quality (screwed end) : 20 mm nominal bore Horizontal

od107218/2019_2020 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SCH40) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work - Exposed on wall 80 mm nominal dia Pipes

od107219/2019_2020 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SCH 40) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work - Exposed on wall 65 mm nominal dia Pipes

od107220/2019_2020 Central hole sink mixer

od107221/2019_2020 Supply and fixing sink cock with long swivel spout (table mounted) in position.

od107222/2019_2020 Supply and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.: 20 mm nominal bore.

od107223/2019_2020 Supplying and fixing white glazed European water closet, wash basin, one hinged hand rails, two grab bars and all associated accessories like flushing cistern, seat and cover, CP brass pillar tap with spatula lever, waste coupling etc. to make the toilet functional for special need persons including cutting and making good the walls and floor, etc. complete.

od107224/2019_2020 Supplying and fixing 520mmx450mm. or nearest size oval wash hand basin of white glazed earthenware (Indian make best quality) counter sunk already built with necessary chipping and chamfering and finishing including supplying and fixing C P brass waste, pillar tap (Heavy, best quality) 1 no. including cutting and making good the walls, providing brackets for supports etc. complete.

od107225/2019_2020 Supplying and fixing white glazed earthenware Urinal of 375X390X590 mm or nearest size (Indian make best quality) fixing with TW plugs and screws embedded in CM, providing 40mm CP waste – 1no, 15mm Angle cock pressmatic with wall flange - 1 no, Urinal spreader including cutting, making good the walls and floors etc. complete.

17.3.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

17.7.4 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x400mm with single 15 mm C.P.brasspillar taps

17.7.6 Providing and fixing wPash basin Rwith C.I. bracIkets, 15Cmm C.P. brEass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Angle back wash basin size 400x400 mm with single 15 mm C.P. brass pillar tap

17.10.1.3 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board510x1040 mm bowl depth 200 mm

17.10.2.1 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink without drain board610x510 mm bowl depth 200 mm

17.28.2.1 Flexible pipe32 mm dia

17.28.2.2 Flexible pipe40 mm dia

17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

17.69.2 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 gms

17.72 Providing and fixing P T M T towel ring traprezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms

8.10.2 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in Charge and finished smooth.Granite Stone of approved shade

18.7.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall15 mm nominal outer dia pipes

18.7.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall20 mm nominal outer dia pipes

18.7.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall25 mm nominal outer dia pipes

18.7.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall32 mm nominal outer dia pipes

18.7.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall40 mm nominal outer dia pipes

18.7.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall50 mm nominal outer dia pipes

18.8.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.15 mm nominal outer dia pipes

18.8.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes

18.8.3 water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes

18.8.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal outer dia pipes

18.9.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work25 mm nominal outer dia pipes

18.9.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work32 mm nominal outer dia pipes

18.9.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work40 mm nominal outer dia pipes

18.9.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work62.50 mm nominal inner dia pipes

18.9.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work75 mm nominal inner dia pipes

18.17.1 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

18.17.2 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.17.3 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

18.17.4 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

18.17.5 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :65 mm nominal bore

18.17.6 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :80 mm nominal bore

18.17.1A Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore

18.18.2 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:20 mm nominal bore

2.10.1.2 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

18.19.4.1 Providing and fixing gun metal non-return valve of approved quality (screwed end):50 mm nominal boreHorizontal

18.21.2.1 Providing and fixing uplasticised PVC connection pipe with brass unions:45 cm length15 mm nominal bore

18.22.1 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet:100 mm diameter

18.32.1 Constructing masonry chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S (non modular) bricks of class designation 7.5

18.37.1 Constructing masonry chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 ( 1 cement : 4 coarse sand) for water meter complete with C.I double flap surface box 400x200x200 mm ( inside ) with locking arrangement and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 grades stone aggregate 20 nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S. ( non modular ) bricks of class designation 7.5

18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.58.1.1 Providing and fixing PTMT grating of approved quality and colour.Circular type100 mm nominal dia

18.65 Providing and fixing PTMT Soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fittings arrangements, weighing not less than 106 gms.

18.76.1 Cutting holes up to 30x30 cm in walls including making good the same:With common burnt clay F.P.S. (non modular ) brick

18.77 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

19.4.1.1 Providing and fixing square-mouth S.W. gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.4.2.1 150x100 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.6.3 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand) including testing of joints etc. complete:250 mm dia R.C. C. pipe

19.6.4 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand) including testing of joints etc. complete:300 mm dia R.C.C. pipe

19.7.1.1 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.7.2.1 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 120x90 cm and 90 cm deep including C.I. cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58 kg):With common burnt clay F.P.S ( non modular) bricks of class designation 7.5

19.8.1.1 Extra for depth for manholesSize 90x80 cmWith common burnt clay F.P.S. ( non modular ) bricks of class designation 7.5

19.8.2.1 Extra for depth for manholesSize 120x90 cmWith common burnt clay F.P.S. ( non modular ) bricks of class designation 7.5

19.16 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steeel bar conforming to IS:1786, having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)Complete as per design

19.32.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

50.17.1.2 Supplying and fixing CP Towel rod 45cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.17.1.5 Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.18.7.6.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10 Kfg/cm - Internal work- Exposed on wall

50.18.8.6.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 10 kgf/cm2

50.18.9.22.8 Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

12.44 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

19.24.1 Dismantling of manhole including R.C.C top slab, C.I. cover with frame, including stacking of useful materials near the site and disposal of unserviceable materials into municipal dumps within 50 m lead:Rectangular manhole 90x80 cm and 45 cm deep

19.24.2 Dismantling of manhole including R.C.C top slab, C.I. cover with frame, including stacking of useful materials near the site and disposal of unserviceable materials into municipal dumps within 50 m lead:Rectangular manhole 120x90cm and 90 cm deep

19.25.1 Extra for depth of manholes dismantled:Rectangular manhole 90x80 cm and beyond 45cm depth

19.25.2 Extra for depth of manholes dismantled:Rectangular manhole 120x90cm and beyond 90 cm depth

15.47.1 Dismantling asbestos cement pressure pipes including excavation and refilling trenches after taking out the pipes manually / by mechanical means and stacking the pipes within 50 metres lead as per direction of Engineer-in-Charge:Upto 150 mm diameter

od111427/2019_2020 Supply, testing and commissioning of Booster pump set having two pumps one working and other standby, capable of delivering min 20Lpm discharge at a head of 3Bar , the system shall be capable of automatic start and stop operation, working of pumps and complete with Hydro tank of 60L capacity, pressure sensors, pressure gauge, pump panel, necessary cabling and bypass arrangements, with skid etc. complete.

od111428/2019_2020 Supply, testing and commissioning of Booster pump set having two pumps one working and other standby, capable of delivering min 50Lpm discharge at a head of 4.5Bar , the system shall be capable of automatic start and stop operation, complete with Hydro tank of 60L capacity, pressure sensors, pressure gauge, pump panel, necessary cabling and bypass arrangements, with skid etc. complete.

od111429/2019_2020 Supply,Erection, Testing and Commissioning of Centrifugal pump (Transfer pump) set capable of lifting 417 lpm of water against a total head of 50m with accessories such as non return valve, full way wheel valve, starter, MCB, voltmeter and ammeter, Indicating lamps, panel board. Foot valve etc.(approximately 10HP, filling time 2hour) (1 working and other standby) (for Domestic water)

ELECTRICAL- LT WORKS

od104933/2019_2020 Installation, Testing and commissioning of all type of recess / surface/ wall mounted lighting fixtures with down rod as requiired.

od104934/2019_2020 Supply of 5m high hot dipped GI octagonal pole with 1m long single arm bracket including foundation

od104935/2019_2020 Supply of 11W all in one LED SOLAR STREET LIGHT having lumen output not less than 2000lm with inbuilt motion sensor and maintenance free Lithium Fero Phosphate Battery(>170Wh capacity ) along with 28Wp,12V Solar panel.Aluminium extruded body and high efficiency with MPPT solar charge controller, IP 65 protection with over charge protection, over current protection and short circuit protection.

od104936/2019_2020 Supply,installation, Testing and Commissioning of LED STREET LIGHTER 1 x 40W LED luminare complete with mono crystaline panel, lithiuIm iron battery, all in one HYBRID type, IP 65 necessary accessories and connections as required.

od104937/2019_2020 Supply of 1x20W LED, 6500k, indoor surface mountable luminaire. 45% energy saving as compared to 40W conventional batten, Comes with diffuser, enhances quality of light.High Power factor (PF >.98) batten.3D Batwing Design channel, enhances light output.Warm start operation, helps in extra long life.

od110944/2019_2020 Supply, installation, Testing and Commissioning of 1 x 15 W LED luminare for recessed down light with decorative cover, ribbed acrylic diffuser etc. complete with necessary accessories and connections as required. ((LD90-191-XXX-61-XX or equivalent Architect approved make .),

od104938/2019_2020 Supply of 36W LED recess DOWN LIGHT with , low loss copper ballast, prewired complete with all necessary accessories as required . ( For ICU / WARD / ANASTHESIA ROOM).

od104939/2019_2020 Supply of wall mounting type 1 x10 W LED Bulk Head luminare complete with necessary accessories and connections as required.(LW07-141-XXX-57-XX or Equivalent Architect approved make ),

od104940/2019_2020 Providing and fixing of any size of copper strip or wire on surface for connections etc. as required., COPPER RATE

od104941/2019_2020 Supply of light duty exhaust fan in plastic body with self opening louvers working on 230V single phase A/C in the existing opening, including making good the damage, connection, testing, commissioning etc. as required 450mm sweep (Heavy duty working on 230 V, AC)(For Service Block ),

od104942/2019_2020 Supply of light duty exhaust fan in plastic body with self opening louvers working on 230V single phase A/C in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 150 mm sweep,

od104943/2019_2020 Supply of 1200 mm ( 48" ) High Speed ceiling fan with all standared accessories like canopy, down rod, shackle set and blade set but without speed regulator.

od104944/2019_2020 Supply, Installation ,Testing and commissioning of Floor Box 264x264x60mm (17Module),

od104945/2019_2020 5/16A Universal Socket ( For ICU / ward/ Anasthesia room / Other approved area ),

od104946/2019_2020 5/16 amps switch with indicator ( For ICU / ward/ Anasthesia room / Other approved area ),

od104947/2019_2020 Supplying and fixing following rating, four pole, 415 volts,MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 100 amps,

od104948/2019_2020 Supplying and fixing following rating, four pole, 415 volts,MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps,

od104949/2019_2020P R I C E Supplying and fixing following rating, four pole, 415 volts,MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps,

od104950/2019_2020 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, RCBO, in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps,

od104951/2019_2020 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, RCBO, in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps,

od104952/2019_2020 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, RCBO, in the existing MCB DB complete with connections, testing and commissioning etc. as required. 32 amps,

od104953/2019_2020 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (8 + 24), Double door,

od104954/2019_2020 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 6 way (8 + 18), Double door,

od104955/2019_2020 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door

od104956/2019_2020 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)<br>8 way (8 + 24), Double door -

od104957/2019_2020 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)<br>6 way (8 + 18), Double door -

od104958/2019_2020 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)<br>4 way (8 + 12), Double door -

2.10.1 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.3 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole

2.10.4 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.10.5 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

2.15.1 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.15.2 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.3.1 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator6 way, Double door

2.3.2 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator8 way,Double door

2.3.3 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator12 way, Double door

2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

2.12.1 Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.12.2 Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.15.3 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

1.5 Wiring for light/ power plug with 2x4 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

1.8.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group A

1.8.2 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group B

1.8.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.9 Wiring for twin control light point with 1.5 sq.mm FRLC PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLC PVC insulated copper conductor single core cable etc as required.

1.14.1 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.14.4 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 6 Sq.mm + 1 x 6 sq.mm earth wire

1.14.5 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 10 sq. mm + 1 X 6 sq. mm earth wire

1.17.1 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.1 x 1.5 sq. mm

1.17.2 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 1.5 sq. mm

1.17.12 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.13 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.4 x 2.5 sq. mm

1.17.20 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 4 sq. mm

1.17.22 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.4 x 4 sq. mm

1.17.29 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 6 sq. mm

1.17.30 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 6 sq. mm

1.17.3 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.17.4 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.4 x 1.5 sq. mm

1.17.11 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 2.5 sq. mm

1.17.21 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

1.17.31 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.4 x 6 sq. mm

1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.21.4 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.40 mm

1.21.5 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.50 mm

1.23.1 Supplying and fixing following piano type switch / socket on the existing switch box/ cover including connections etc. as required.5/6 amps switch

1.23.2 Supplying and fixing following piano type switch / socket on the existing switch box/ cover including connections etc. as required.2 way 5/6 amps switch

1.23.3 Supplying and fixing following piano type switch / socket on the existing switch box/ cover including connections etc. as required.15/16 amp switch

1.23.4 Supplying and fixing following piano type switch / socket on the existing switch box/ cover including connections etc. as required.3 pin 5/6 amp socket outlet

1.23.5 Supplying and fixing following piano type switch / socket on the existing switch box/ cover including connections etc. as required.6 pin 15/16 amp socket outlet

1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.27.1 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.27.4 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.27.5 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

1.27.6 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.12 Module (200mmX150mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or inrecess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 ampsmodular switch, connection etc. as required. (For light plugs to be used in non residentialbuildings).

1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden blockincluding connection etc as required.

1.34 Supplying and fixing brass batten/ angle holder including connection etc. as required.

1.44 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standardlength (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc.as required.

1.49 Numbering of ceiling fan / exhaust fan/ fluorescent fittings as required-Painting.

1.50.1 Installation of exhaust fan in the existing opening, including making good the damage connection testing, commissioning etc. as required.Upto 450 mm sweep

1.51 Extra for fixing the louvers/shutters complete with frame for a exhaust fan of all sizes

ELECTRICAL-HT WORKS

od106430/2019_2020 Supply, Installation, Testing and commissioning of 2kVA online UPS with inbuilt battaery, 2kVA UPS with Battery

od106431/2019_2020 Supply of Insulated hand gloves IS 4770/1991, Hand Gloves

od106432/2019_2020 'Supply and installation of Laminated copies of Approved/ as built schemes and drawings in electrical room , Laminated Copy

od106433/2019_2020 Supply and installation of Danger board as required by the electrical authorities. Danger Board

od106434/2019_2020 Supply and fixing CO2 type 4.5KG capacity trolley mounted fire extinguishers as appoved by ISI complete as required, CO2 type 4.5kg

od106435/2019_2020 Supply and Installation of Cable route marker for HT UG Cable at every 10m interval made of Cast Iron ( 152mm Round ), Cable route marker

od106436/2019_2020 Supply fabrication and erection of exhaust pipe for carrying exhaust smoke from500kVA (200mm) through existing masonary duct using MS pipe with 50mm increase in diameter for every 10m with asbestos fibre insulation, AL cladding, necessary suports etc complete. Exhaust Pipe

od106437/2019_2020 Supply and installation of emergency OFF trip push button with front Glass and painted in RED Colour. Emergency off trip push button

od106438/2019_2020 Supply and installation of 2nos fire buckets along with stand painted with enamel paint of red colour. Fire buckets

od106439/2019_2020 Supply and installation of rubber mat with ISI mark suitable for 11 KV,2.5mm THICKinstallation. Rubber mate

6.7 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightningconductor complete as required.(For horizontal run)

6.8 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightningconductor complete as required.(For vertical run)

6.12 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

6.14 Providing and laying G.l. tape 32 mm X 6 mm from earth. electrode directly in ground as required.

6.15 Laying copper/ G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

od106440/2019_2020 Providing and fixing of any size of copper strip or wire on surface for connections etc. as required. Copper rate

5.2 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providingmasonry enclosure with cover plate having locking arrangement and watering pipe etc. withcharcoal/ coke and salt as required

5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.17 Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing asrequired.

5.20 Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required

od106441/2019_2020 Supplying, installation, including suspension, testing and commissioning of following capacity bus trunking with aluminium bus bars in aluminium enclosure in convenient sections for use on, 3 phase, 4 wire, 415 volts, 50 Hz, A.C. supply with class B insulation including jointing of sections, flexible joints,flange end, elbows,expansion joints, bends and earthing with 2 runs of copper strips, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. .( Bus truncking confirming to ROHS Standards, and IP 54 Protection )<br>2000 amps

od106442/2019_2020 Supplying, installation, including suspension, testing and commissioning of following capacity bus trunking with aluminium bus bars in aluminium enclosure in convenient sections for use on, 3 phase, 4 wire, 415 volts, 50 Hz, A.C. supply with class B insulation including jointing of sections, flexible joints,flange end, elbows,expansion joints, bends and earthing with 2 runs of copper strips, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. .( Bus truncking confirming to ROHS Standards, and IP 54 Protection ) <br>1600 amps

9.1.20 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)

9.1.21 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)

9.1.22 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)

9.1.23 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.24 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulatOedtahnedrPEVCnsghienateheedri/nXgLPOE ralgumaniniiusmatcioondnusctor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)

9.1.25 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)

9.1.26 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm)

9.1.27 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.29 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

9.1.30 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 300 sq. mm (70mm)

9.1.31 Supplying and making end termination with brass compression gland and aluminium lugs for following Size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 400 sq. mm (82mm)

9.1.32 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

7.1.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade offollowing size direct in ground including excavation, sand cushioning, protective covering andrefilling the trench etc as required.Upto 35 sq. mm

7.1.2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade offollowing size direct in ground including excavation, sand cushioning, protective covering andrefilling the trench etc as required.Above 35 sq. mm and upto 95 sq. mm

7.1.3 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade offollowing size direct in ground including excavation, sand cushioning, protective covering andrefilling the trench etc as required.Above 95 sq. mm and upto 185 sq. mm

7.1.4 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade offollowing size direct in ground including excavation sand cushioning protective covering andrefilling the trench etc as required.Above 185 sq. mm and upto 400 sq. mm

7.5.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade offollowing size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm

7.5.2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade offollowing size in the existing RCC/ HUME/ METAL pipe as required.Above 35 sq. mm and upto 95 sq. mm

7.5.3 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade offollowing size in the existing RCC/ HUME/ METAL pipe as required.Above 95 sq. mm and upto 185 sq. mm

7.5.4 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade offollowing size in the existing RCC/ HUME/ METAL pipe as required.Above 185 sq. mm and upto 400 sq. mm

7.8.1 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KVgrade of following size on cable tray as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.8.2 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KVgrade of following size on cable tray as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.8.3 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KVgrade of following size on cable tray as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.8.4 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KVgrade of following size on cable tray as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

od106443/2019_2020 Supply testing and commissioning of the single core copper cables for working voltage upto and including 1100 V<br>1 x 1C x 120 Sq.mm

od106444/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 4C x 4 Sq.mm.

od106445/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 4C x 6 Sq.mm.

od106446/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 4C x 400 Sq.mm 2XFY Cable

od106447/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3C x 185 Sq.mm.

od106448/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3C x 10 Sq.mm.

od106449/2019_2020P Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3C x 6 Sq.mm.

od106450/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 4C x 10 Sq.mm.

od106451/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 4C x 16 Sq.mm.

od106452/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3.5C x 25 Sq.mm.

od106453/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3.5C x 35 Sq.mm..

od106454/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3.5C x 50 Sq.mm.

od106455/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3.5C x 70 Sq.mm.

od106456/2019_2020P Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3.5C x 95 Sq.mm

od106457/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3.5C x 120 Sq.mm.

od106458/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3.5C x 150 Sq.mm.

od106459/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3.5C x 185 Sq.mm.

od106460/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3.5C x 240 Sq.mm.

od106461/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE<br>1 x 3.5C x 300 Sq.mm.

od106462/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE<br>1 x 3.5C x 400 Sq.mm

od106463/2019_2020P Supply, installation, Testing and Commissioning of Main Emergency Panel, UPS Panel,

od106464/2019_2020 Supply, installation, Testing and Commissioning of Main Emergency Panel ,

od106469/2019_2020 Supply, fabrication, erection, testing and commissioning of UTILITY Panel board fabricated out of 14/16 SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust and vermin proof with reinforcement wherever necessary fully meeting all the requirement specified in the technical specifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPN switch gear shall be supplied with equally rated neutral link. All indication lamps should be LED type, all MCCBs should be with rotary handle.The panel shall be fabricated as per IS standards and KSEI specifications by a CPRI approved vendor.

od106470/2019_2020 Supply, fabrication, erection, testing and commissioning of MEDICAL EQUIPMENT Panel board fabricated out of 14/16 SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust and vermin proof with reinforcement wherever necessary fully meeting all the requirement specified in the technical specifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPN switch gear shall be supplied with equally rated neutral link. All indication lamps should be LED type, all MCCBs should be with rotary handle.The panel shall be fabricated as per IS standards and KSEI specifications by a CPRI approved vendor.

od106471/2019_2020 Supply, fabrication, erection, testing and commissioning of MEDICAL EQUIPMENT Panel board fabricated out of 14/16 SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust and vermin proof with reinforcement wherever necessary fully meeting all the requirement specified in the technical specifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPN switch gear shall be supplied with equally rated neutral link. All indication lamps should be LED type, all MCCBs should be with rotary handle.The panel shall be fabricated as per IS standards and KSEI specifications by a CPRI approved vendor.

od106472/2019_2020 Supply, fabrication, erection, testing and commissioning of APFC Panel board fabricated out of 14/16SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust and verminproof with reinforcement wherever necessary fully meeting all the requirement specified in the technicalspecifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPN switch gearshall be supplied with equally rated neutral link. All indication lamps should be LED type.The panel shallbe fabricated as per IS standards and KSEI specifications by a CPRI approved vendor.

od106473/2019_2020 Supply, fabrication, erection, testing and commissioning of LOUNDRY Panel board fabricated out of 14/16 SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust and vermin proof with reinforcement wherever necessary fully meeting all the requirement specified in the technical specifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPN switch gear shall be supplied with equally rated neutral link. All indication lamps should be LED type, all MCCBs should be with rotary handle.The panel shall be fabricated as per IS standards and KSEI specifications by a CPRI approved vendor.

od106474/2019_2020 Supply, fabrication, erection, testing and commissioning of LOUNDRY Panel board fabricated out of 14/16 SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust and vermin proof with reinforcement wherever necessary fully meeting all the requirement specified in the technical specifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPN switch gear shall be supplied with equally rated neutral link. All indication lamps should be LED type, all MCCBs should be with rotary handle.The panel shall be fabricated as per IS standards and KSEI specifications by a CPRI approved vendor. LAUNDRY PANEL 1 ,

od106475/2019_2020 Supply, fabrication, erection, testing and commissioning of Main AC Panel board fabricated out of 14/16 SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust and vermin proof with reinforcement wherever necessary fully meeting all the requirement specified in the technical specifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPN switch gear shall be supplied with equally rated neutral link. All indication lamps should be LED type, all MCCBs should be with rotary handle.The panel shall be fabricated as per IS standards and KSEI specifications by a CPRI approved vendor.

od106476/2019_2020 Supply, fabrication, erection, testing and commissioning of Main Utility Panel board fabricated out of14/16 SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust andvermin proof with reinforcement wherever necessary fully meeting all the requirement specified in thetechnical specifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPNswitch gear shall be supplied with equally rated neutral link. All indication lamps should be LED type, allMCCBs should be with rotary handle.The panel shall be fabricated as per IS standards and KSEIspecifications by a CPRI approved vendor.

od106477/2019_2020 Supply, fabrication, erection, testing and commissioning of SSB Panel board fabricated out of 14/16 SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust and vermin proof with reinforcement wherever necessary fully meeting all the requirement specified in the technical specifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPN switch gear shall be supplied with equally rated neutral link. All indication lamps should be LED type, all MCCBs should be with rotary handle.The panel shall be fabricated as per IS standards and KSEI specifications by a CPRI approved vendor.

od106478/2019_2020 Supply installation testing and commissioning of 2 DG auto synchronization and auto load sharing system using DEIF AGC 242 controller with IOM 220 module . Analog regulation module for GOVERNOR and AVR should placed at DG side with can bus communication. Controller should have in built protection for reverse power 2 levels, over current 6 levels, voltage dependent over current, over voltage 2 levels, under voltage 3 levels, over frequency 3 levels, under frequency 3 levels, overload 5 levels, unbalanced current etc.<br>All synchronization controller in system shall have USB port for programming. Modbus (rs-485) and ethernet communication - for remote/dcs monitoring, CAN bus for load sharing communication for synchronization control

od106479/2019_2020 Supply, fabrication, erection, testing and commissioning of MSB panel board fabricated out of 14/16 SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust and vermin proof with reinforcement wherever necessary fully meeting all the requirement specified in the technical specifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPN switch gear shall be supplied with equally rated neutral link. All indication lamps should be LED type.The panel shall be fabricated as per IS standards and KSEI specifications by a CPRI approved vendor. MSB PANEL

od106480/2019_2020 Installation, Testing OantdhCeormmEisnsgioniningeeofr8i0nkgVAOUPrSgawnithisbaattteiroy nbasnk of 12V batteries,15 minutes back up at full load along with suitable capacity battery breaker, battery connecting wires and battery stand.

od106481/2019_2020 Supply of 80 KVA true online UPS with 3 phase input and 3 phase output, inbuilt isolation transformer , dual redundant , microprocessor based, double conversion topology, IGBT based invertor and rectifier, features of provision of parallel redundancy, each UPS with separate battery bank of 12V batteries,15 minutes back up at full load along with suitable capacity battery breaker, battery connecting wires and battery rac 80 KVA UPS WITH BATTERY BANK

od106482/2019_2020 Supply, installation, testing and commissioning of 500 KVA, 415V, 3 phase, 1500 R.P.M, 0.8 PF water cooled, floor mounted Diesel Generator set with acoustic enclosure and control panel,necessary controls, contactors, timers, meters,energy meter, indication lamps etc as required for synchronisation of two DG sets, Suitable ACB with shunt trip and adjustable over load 0.4In to 1 In and adjustable short circuit 2 to 10 Ir and ON- OFF push buttons. Relays, CTs and transducers for metering and protection. Fuel pipe line, (to be concealed under floor), exhaust pipe line (to be erected with sufficient M.S supports and insulated, hood on top), Antivibration mountings, residential type silencer, electric starter, battery & battery charger, fuel tank, radiator, control wiring etc. 500 KVA DG set with PLC controlled Synchronisation Fascility,

od106483/2019_2020 'Supply, installation, testing and commissioning of Cast Resin Transformer consisting of 1250 KVA, 11KV/433V, 3 phase, Vector group DYN-11 , Dry type, copper wound, class F insulation associated with winding temperature indicator / controller actuated by means of resistance temperature detector embeded in LV windings, indoor type , transformer with On load tappings from +5% to -15% in steps of1.25%, operated by CTR make 11 KV OLTC, RTCC and AVR, cable box at primary ( HT side ) and secondary side ( LT side )shall be connected through busduct, complete with all fittings and accessories confirming to IS specifications , inter connection of control cables and accessories etc complete. The transformer will be as per detailed CPWD technical specifications and as required.(include HT TOD meter,CT,PT,etc completed), 1250 KVA Transformer,

od106484/2019_2020P Supply of all materials and termination of HT cables using Heat shrinkable type 11KV(E), XLPE Cable termination kits, Cable identification tags etc. for the following Cross linked Polyethylene Insulated (XLPE)and Armoured Aluminium H.T.Cables (A2XCEFY) . 3.0Cx150 SQ.MM.

10.4.4 Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:300 sq. mm

8.1.2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade offollowing size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 120 sq. mm and upto 400 sq. mm

8.2.2 Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KVgrade of following size direct in ground in the same trench in one tier horizontal formationincluding excavation, sand cushioning, protective covering and refilling the trench etcAbove 120 sq. mm and upto 400 sq. mm

8.3.2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade offollowing size in the existing RCC/ HUME/ METAL pipe as required.Above 120 sq. mm and upto 400 sq. mm

8.4.2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade offollowing size in the existing masonry open duct as required.Above 120 sq. mm and upto 400 sq. mm

od106485/2019_2020 Supply , testing and commissioning of the following PVC Insulated Armoured Aluminium Cables (AYWY/AYFY) /XLPE (A2XCEFY) H.T trenches, cable trays, hume pipes, including supply and fixing of painted MS clamps not exceeding 60cms, nuts and bolts, screws,identification tags,route markers etc. required for clamping intervals as neceessry. 3.0Cx 150 SQ.MM. XLPE,

od106486/2019_2020 Supply , testing and commissioning of the following PVC Insulated Armoured Aluminium Cables (AYWY/AYFY) /XLPE (A2XCEFY) H.T trenches, cable trays, hume pipes, including supply and fixing of painted MS clamps, spacing of the clamps not exceeding 60cms, nuts and bolts, screws, identification tags, route markers etc. required for clamping intervals as necessry. 3.0Cx 300 SQ.MM. XLPE,

od106487/2019_2020 Supply, Installation, Testing and Commissioning of SCADA software Runtime License with 512 tags for the substation Automation system,

od110909/2019_2020 'Supply, erection, testing and commissioning of 11KV VCB Panel consisting of 3 Nos 800A 25kA VCB, incomer and outgoings as per the detailed specifications and drawings including connections etc. complete with following incomers , out goings including door interlocking and TOD meter as rquired ( Other details as per schematic drawing and technical specification.

od110934/2019_2020 Supply testing and commissioning of the following PVC Insulated Armoured Aluminium M.V.Cables XLPE <br>1 x 3C x 400 Sq.mm.

ELEVATORS

od104696/2019_2020 20 PASSENGER BED lift without<br>Machine Room Serving 08 stops

od110951/2019_2020 DUMP ELEVATORS

od130357/2019_202O0 ther Engineering Organisations Supply, installation, Testing and Commissioning of Load bank for Lifts,

od130380/2019_2020 08 PASSENGER lift without<br>Machine Room Serving 08 stops

BIO GAS PLANT

od110053/2019_2020 Supplying and filling cowdung with eaqual quandity of water for bactetria formation

od110054/2019_2020 Supplying and fixing 24 cft biogas burner including all connections, control valves & all plumbing works etc

od110055/2019_2020 Providing and Fixing Chlorinated Polyvinyl chloride(CPVC) SDR 11 pipes, having thermal stability for hor and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per the direction of engineer in charge (Conceled work including cutting chases and making good the wall etc)

od110056/2019_2020 Supplying and fixing 250 mm dia PVC pipe from Inscpection chamber to Fermetation Tank gas out let connections including control valves, all plumbing works etc

od110057/2019_2020 Supplying and fixing 32 mm dia GI pipe for gas out let connections including control valves, all plumbing works etc

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavators) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.9.1 Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.Ordinary rock

2.16.1 Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete (Measurements to be taken of the face area timbered).Depth not exceeding 1.5m

2.26.1 Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

60.2.4 BAILING OUT WATER USING PUMP ABOVE 10HP AND UP TO 20HP - Bailing out water with engine and pump set above 10HP and up to 20HP, including conveyance to site and erection,cost of fuel, lubrication oil and other stores, pay of staff etc complete

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for masOs ctohnecrreteEn

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.33.1 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.35 Add for using extra cement in the items of design mix over and above the specified cement content therein

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

6.4.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:4 ( 1 cement : 4 coarse sand)

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

6.10 Brick work in gauged arches in superstructure above plinth level and upto floor five level in cement mortar 1:3 (1 cement : 3 coarse sand) including centering and shuttering complete, for span up to 6 meters with common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

13.7.1 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

19.18.1 Supplying and fixing C.I with out frame for manholes:455 x 610 mm rectangular C.I cover ( light duty ) the weight of the cover to be no less than 23 kg

7.1.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

WATER PURIFIER

od109431/2019_2020 SUPPLY AND INSTALLING OF FOLLOWING INDUSTRIAL 500lph UV PLANT AND WATER COOLER PC480

FIRE FIGHTING

od105788/2019_2020 Supply installation testing and commissioning of Talk back Unit

od105789/2019_2020 Supplying and installing in position "Assembly Point" and "Way to assembly point "sign boards of sixe (180 X 300 mm)

od105790/2019_2020 Supplying and installing in position "FIRE DUCT" sign boards of sixe (180 X 300 mm)

od105791/2019_2020 Supplying and installing in position "FIRE EXIT" sign boards of sixe (180 X 300 mm)

od105792/2019_2020 Supplying and installing in position self glowing "FIRE EXIT" sign boards of sixe (150 X 400 mm) made of luminescent safely, rigid sheet in green colour, photo luminescent ACP sheet in protective glass with two hanging chains & necessary supports to hang it on ceiling.

od105793/2019_2020 Supply and laying of PVC insulated 1sq mm copper Cable for Talk Back Unit

od105794/2019_2020 Supply and laying of 20mmPVC rigid conduit with fixing material

od105795/2019_2020 Supply installation testing and commissioning of Hooter

od105796/2019_2020 Supply, installing, testing and commissioning of HEAT DETECOTORS with base

od105797/2019_2020 Smoke Detector Supplying, installation, testing & commissioning

od105798/2019_2020 Supply, laying and clamping of PVC insulated and PVC sheathed armoured copper fire alarm cable 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages, colour washing etc. as required. (2X 1.50 sq mm)

od105799/2019_2020 Supplying, installation, testing & commissioning of main control and indicating panel made out of 16 SWG MS sheet to accommodate the following items duly powder coated in approved colour with louvers for ventilation, locking arrangement, audio and visual indication for fire alarm and public address system, monitoring system including connections, interconnections etc complete as required. 6 zone panel for fire alarm system 100 watt amplifier racks suitable for operation on 230 V AC/24V DC supply conforming to IEC-268-3 complete with all DELHI SCHEDULE OF RATES (E&EM) 2018 65 accessories as required- 2 Nos.(one to act as standby)

od105801/2019_2020 Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required

od105802/2019_2020 Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required

od105803/2019_2020 Supplying, and fixing of CO2 type fire extinguisher of 4.5 Kgs. Capacity, with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union, discharge hose, wall mounting bracket etc.

od105804/2019_2020 Supplying, and fixing of Dry chemical powder type fire extinguisher of 4 Kgs. Capacity, with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union, discharge hose, wall mounting bracket etc.

od105806/2019_2020 Supply, installing, testing and commissioning of Air cushion vessel made of mild steel of 200mm dia with automatic air release cock,25mm dia drain valve and shutt off.The vessel shall be 100cm in height etc. Complete. operation with required acessaries like taflon tape,etc

od105807/2019_2020 Supply ,Installation, testing and commissioning of Pressure Guage for automatic operation with required accessories like taflon tape,etc pressure gauge dial type 100mm

od105808/2019_2020 Supply , Installation, testing and commissioning of Pressure Switch with required acessaries like taflon tape,etc

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft,mechanical seal conforming to IS 1520 Suitable HP, 1500 RPM water cooled with radiator,diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 2280 LPM at 80 m

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic ,operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC,synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plasteredwith anti vibration pads. 2280 LPM / 80 m head

od105812/2019_2020 Supply, Installation,Testing and Commissioning of approved type Rosette plates (Dome type, in onepiece) for Sprinklers below false ceiling area. The Rosette shall be chrome plated & shall be as approved by architects / consultants

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :Pendent Sprinkler

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. forsuitable dia MS pipe connection conforming to IS 904 as required : 4WAY -150 mm dia M.S. Pipe

od105815/2019_2020 Supplying, installing, testing and commissioning of Ball valves with fittings of screwed end type with ISI mark. Size : 20MM

od105816/2019_2020 Supply, installation, testing and commissioning of single acting Air Release Valve with screwed inlet 15 mm dia etc.

od105817/2019_2020 Supplying, installing, testing and commissioning of Ball valves with fittings of screwed end type with ISI mark. Size : 32MM

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic(Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. Hose of 30M. length

od105819/2019_2020 Supply, installation, testing and commissioning of Double Door Hose Cabinet to accommodate two piece of hose pipe along with one pair of male and female coupling and one branch pipe. The cabinet is made of 20swg M.S Sheet, glass fronted with hinged door and lock. The cabinet is spray painted to scarlet red color

Supplying and fixing 63 mm dia, 15 m long RRL hosepipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)

Supplying & fixing 63 mm dia short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)

Supplying and fixing single headed internal hydrant valve with instantaneous Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Stainless Steel cap and chain as required : Single headed Stainless steel

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 100mm dia

Providing, installation, testing and commissioning of non-return valve of PN 16 slim seal type of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 150 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 16 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : complete. Size : 65 MM

Supplying, fixing, testing and commissioning of butterfly valve of PN 16 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : complete. Size : 80mm

Supplying, fixing, testing and commissioning of butterfly valve of PN 16 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : Size : 150 MM

od105828/2019_2020 Under Ground Piping: Supply, Erection, testing and commissioning of MS 'C' class Pipes confirming to IS:1239 part - I with malleable specials confirming to IS:1239 part - II, such as Supply and Installation of elbows, reducers, flanges etc. Including cutting, Welding, laying under ground, by using suitable supports,and wrapping with polymer corrossion protection tape confirming to IS 10221 with proper overlapping, trimming etc complete. etc. complete Size : 80 mm Dia

od105829/2019_2020 Under Ground Piping: Supply, Erection, testing and commissioning of MS 'C' class Pipes confirming to IS:1239 part - I with malleable specials confirming to IS:1239 part - II, such as Supply and Installation of elbows, reducers, flanges etc. Including cutting, Welding, laying under ground, by using suitable supports,and wrapping with polymer corrossion protection tape confirming to IS 10221 with proper overlapping, trimming etc complete. etc. complete Size : 100 mm Dia

od105830/2019_2020 EXHAUST PIPE<br>Supply and Instalation of Exhaust pipe for Diesel engine of 150 mm dia MS C Class pipe and Supply and errection of with mineral wool insulation & aluminum sheet cladding with all necessary item supply and errection

od105831/2019_2020 Above Ground Piping: Supply, Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red ) etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 25mm Nominal Dia

od105832/2019_2020 Above Ground Piping: Supply, Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red )etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 32mm Nominal Dia

od105833/2019_2020 Above Ground Piping: Supply, Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red )etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 40mm Nominal Dia

od105834/2019_2020 Above Ground Piping: Supply, Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red ) etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 50 mm Nominal Dia

od105835/2019_2020 Above Ground Piping: Supply, Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red ) etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 65 mm Nominal Dia

od105836/2019_2020 Above Ground Piping: Supply, Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red )etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 80 mm Nominal Dia

od105837/2019_2020 Above Ground Piping: Supply, Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red )etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 100 mm Nominal Dia

od105838/2019_2020 Above Ground Piping: Supply, Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red ) etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 150 mm Nominal Dia

Providing, fixing, testing & commissioning of 15mm diaquartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : complete UP RIGHT Type

od130368/2019_2020 Supply, fabrication, erection, testing and commissioning of Fire pumb Panel board fabricated out of 14/16 SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust and vermin proof with reinforcement wherever necessary fully meeting all the requirement specified in the technical specifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPN switch gear shall be supplied with equally rated neutral link. All indication lamps should be LED type, all MCCBs should be with rotary handle.The panel shall be fabricated as per IS standards and KSEI specifications by a CPRI approved vendor

RO PLANT FOR DIALYSIS UNIT AND CSSD

od105852/2019_2020 Supply, Installation, Testing and Commissioning of UV System for elimination of bacterial contamination, the MoC of the pipes shall be SS and the UV will have Min: 40 w power with all necessary piping interconnections as required.

od105853/2019_2020 Supply, Installation, Testing and Commissioning of Recirculation pump for the feeding water to dialysis unit and CSSD etc. including all required suction and delivery piping & valving, pressure guages etc completeMoC of the pump shall be Stainless steel, Configuration 1W+1S.Flow rate = 2000 Litres/Hr, Head: 30 m

od105854/2019_2020 Supply, Installation, Testing and Commissioning of Pyrogen Filters of 0.1-0.3 mm pore size at inlet & outlet of the high pressure pump with all necessary piping interconnections as required.

od105855/2019_2020 Supply, Installation, Testing and Commissioning of SS 304 Collection tank of 5000 Liters having 1.5 mm Shell Thickness, with all necessary piping interconnections as required.

od105856/2019_2020 Supply, testing & commissioning of 1000 LPH R.O plant, with all accessories like Pressure Gauge, pressure switch for Low & High flow, Flow Indicators, conductivity meters, SS Pressure tubes to house Membranes, High pressure Pump, Water Panel- SS Panel to house Pressure Gauge & Rota Meters Electrical Control Panel, Water Panel, Micron Filter & Antiscalents dosing pum,Auto Flushing Unit, Electrical Control Panel with contactor for pumps, power on & trip indicators etc on EX Kerala basis. Commissioning charges included. The cost shall include all required Piping in Sch 40 UPVC ASTM, Valving with compatible materials and necessary measurements for pressure and flow.

od105858/2019_2020 Supplying, installing, testing and commissioning approved make Raw Water Activated carbon filter with necessary Accessories complete with Frontal Piping, valves, suitable supports for mounting pressure gauges, orifice plates. The cost of filter shall also include initial charge of underbed & multi -grade filter media to suit the requirement etc complete as per standards.

od105859/2019_2020 Supplying, installing, testing and commissioning approved make Raw Water Pressure sand filter with necessary Accessories complete with Frontal Piping, valves, suitable supports for mounting pressure gauges, orifice plates. The cost of filter shall also include initial charge of underbed & multi -grade filter media to suit the requirement etc. complete as per standards.

od105860/2019_2020 Supply, Installation, Testing and Commissioning of Feed pump for the feeding water to dialysis unit and CSSD etc including all required suction and delivery piping & valving, pressure guages etc complete.. MoC of the pump shall be Stainless stee (SS304 or higher), Configuration 1W+1S

od108810/2019_2020 Providing and applying Epoxy coating over PCC Surface with all materials and Labour

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

2.27 Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming consolidating and dressing complete.

7.1.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bandes,plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering,finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.5 Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.10.1 Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

13.3.1 20 mm cement plaster of mix:1:4 (1 cement : 4 fine sand)

13.7.2 12 mm cement plaster finished with a floating coat of neat cement of mix:1:4 ( 1 cement : 4 fine sand)

13.48.1 Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @0.75 ltr/10 sqm

13.48.3 Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture

21.1.1.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.3.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

10.6.2 Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.20 mm M.S. laths with 1.20 mm thick top cover

10.7 Providing and fixing ball bearing for rolling shutters.

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.51.1 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete:Ridges plain (500-600 mm)

SEWAGE TREATMENT PLANT

2.8.1 Earth work in excavation by mechanical means (Hyrdraulic excavators) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

50.6.2.1 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.7.1 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

13.4.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)

50.18.9.10.1 Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

19.20 Supplying and fixing C.I cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg

2.26.1 Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

6.1.2 Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, bOuttetrhesesresE, pnlingthinanedesrtriinnggcoOursregs aetnc

13.21 Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

od100536/2019_2020 Paving of bricks at bottom and filling the pit with brickbats including material, transportation & labour<br>and laying sand envelop around the soakpit<br>

19.19.1.1 Providing and fixing in position Pre-cast R.C.C. manhole cover and frame of required shape and approved quality.L D - 2.5Rectangular shape 600x450 mm internal dimensions

7.1.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

50.6.1.5 Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.19 Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.9.3 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

13.16.1 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

11.37 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

9.117.1 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1 mm), with wall thickness 2.0mm (±0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer-in-chargeExtruded section profile size 48x40 mm

9.118.1 Providing and fixing to existing door frames24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness,fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge( For W.C. and bathroom door shutter).

21.1.1.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

13.37.1 White washing with lime to give an even shade:New work (three or more coats)

od101253/2019_2020 Air Blowerº<br>Capacity : 120 m3/hr<br>Make: Everest/Kay/ Equivalent<br>Motor- 5 Hp,3 phase<br>Make : Everest/ Equivalent

od101248/2019_2020 Coarse Screen<br>MOC : SS<br>Size:25mm x 6mm<br>Opening: 15mm<br>Inclined at 50º

od101249/2019_2020 Transfer pumps in Collection tank<br>Capacity : 1.0 m3/hr<br>0.5 Hp, 3 phase<br>Head : 8-12 m<br>Type : Self Priming,<br>non clogging type<br>Make : Kirloskar/ Equivalent

od101250/2019_2020 Transfer pumps inEqualisation tank<br>Capacity : 5.0 m3/hr<br>1.5 Hp, 3 phase<br>Head : 12-15 m<br>Type : Self Priming,<br>non clogging type<br>Make : Kirloskar/ Equivalent

od101251/2019_2020 Aeration Manifold and Sieves for<br>Aeration Tank<br>Size: 67mm OD X 1000mm long

od101252/2019_2020 MBBR Bio Media<br>Material : Polyethylene<br>Density; 926kg/m3<br>Quantity :9000 kg<br>Cylindrical shaped with 10mm dia<br>and 7mm height

od101254/2019_2020 Flash mixer with Motor , Gearbox,<br>Stirrer and Holding frame<br>Motor: Electric motor of 1 hp<br>Make: Siemens/ Crompton/<br>Kirloskar/equivalent<br>Gearbox: Radicon /<br>Elecon/equivalent make<br>Wetted Parts : FRP / SS<br>Impeller : Four blades pitched paddle<br>turbine type impeller

od101255/2019_2020 Hypochlorite Dosing System<br>Accessories : Dosing pump with 100<br>L PP Storage tank<br>0-5 LPH, 6 Bar Pressure<br>Make: Milton Roy /E-Dose/ Eqvt.<br>Type: Diaphragm

od101256/2019_2020 Coagulant Dosing System<br>Accessories : Dosing pump with 100<br>L PP Storage tank<br>0-5 LPH, 6 Bar Pressure<br>Make: Milton Roy/ Eqvt.<br>Type: Diaphragm

od101257/2019_2020 Pressure Sand Filter<br>Size: 1.0m Dia x 1.8m Ht.<br>Type : Vertical<br>Valve : Multiport<br>MOC : MSRL<br>Filter media: Graded pebbles with<br>Silex and Fine sand

od101258/2019_2020 Pressure Carbon Filter<br>Size: 1.0m Dia x 1.8m Ht.<br>Type : Vertical<br>Valve : Multiport<br>MOC : MSRL<br>Filter media: Graded pebbles with<br>Activated carbon, Coarse and fine<br>sand

od101259/2019_2020 Filter Feed Pump<br>Capacity : 5 m3/hr<br>1.5 hp, 3 phase<br>Type : Horizontal Centrifugal pump<br>Make: Kirloskar /Eqvt.

od101260/2019_2020 Sludge Transfer Pump<br>Capacity : 5 m3/hr<br>Type: Self priming pump<br>1Hp, 3 phase<br>Make: Kirloskar / Eqvt

od101261/2019_2020 Sintex water storage tanks<br>Type: Polyethylene<br>Capacity : 1000 L

od101262/2019_2020 Control Panel board, Electical<br>fittings, wiring,cable for connection,<br>earthing etc including cost of<br>material and labour,erection and<br>commissioning.<br>

od130360/2019_2020 Supply, fabrication, erection, testing and commissioning of STP Panel board fabricated out of 14/16 SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust and vermin proof with reinforcement wherever necessary fully meeting all the requirement specified in the technical specifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPN switch gear shall be supplied with equally rated neutral link. All indication lamps should be LED type, all MCCBs should be with rotary handle.The panel shall be fabricated as per IS standards and KSEI specifications by a CPRI approved vendor.

WATER TREATMENT PLANT

od105996/2019_2020 Supplying, installing, testing and commissioning Electrical Control Panel Suitable for Auto/Manual operation. The panel shall have Switch gear, MCB, OLR, Single Phase Preventer, H/L Protection, Push Button, Indication Lamp etc. of approved make

od105997/2019_2020P R I C E Supplying, installing, testing and commissioning approved make Treated Water Transfer Pump including all required suction and delivery piping & valving, pressure guages etc complete. MoC of the pump shall be CI, Configuration 1W+1S

od105999/2019_2020 Supplying, installing, testing and commissioning approved make Raw Water Activated carbon filter with necessary Accessories complete with Frontal Piping, valves, suitable supports for mounting pressure gauges, orifice plates. The cost of filter shall also include initial charge of underbed & multi -grade filter media to suit the requirement etc complete as per standards.Size of filter:1050mm dia, height of 1800mm

od106000/2019_2020 Supplying, installing, testing and commissioning approved make Raw Water Pressure sand filter with necessary Accessories complete with Frontal Piping, valves, suitable supports for mounting pressure gauges, orifice plates. The cost of filter shall also include initial charge of underbed & multi -grade filter media to suit the requirement etc. complete as per standards.Size of filter:1050mm dia, height of 1800mm

od106001/2019_2020 Supplying, installing, testing and commissioning approved make Raw Water Iron Removal filter with necessary Accessories complete with Frontal Piping, valves, suitable supports for mounting pressure gauges, orifice plates. The cost of filter shall also include initial charge of underbed & multi -grade filter media to suit the requirement etc. complete as per standards.Size of filter:1050mm dia, height of 1800mm

od106002/2019_2020 Supplying, installing, testing and commissioning approved make Filter Feed pump for feeding water to the Filtration Plant including all required suction and delivery piping & valving, pressure guages etc complete.Flow rate:15cum/hr, Head:30m

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.9.16.1 Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

50.6.1.5 Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.6.1 20 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 TypeA, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter

12.51.1 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete:Ridges plain (500-600 mm)

50.10.1 Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

9.48.2 Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

13.48.3 Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture

od111177/2019_2020 Finishing of PCC floor with self level epoxy coating

INCINERATOR

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

7.1.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.33.1 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

50.10.1 Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

9.48.2 Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

od130499/2019_2020 Supply, Installation, Testing and commissioning I Unit of<br>NOWASTE scientific incinerator – capacity 150 kg/hour.<br>Effective Height – 30 meters from ground level including<br>I. Primary Combustion Chamber, Secondary Combustion Chamber, Air Pollution Control Unit – Wet Scrubber, Emission Stack [Effective Height – 30.0 meters from G. Level], Supporting Tower, Lightning Protection, Water Pump and accessories

HVAC LOWER SIDE

od146511/2019_2020 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.&lt;br&gt;Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006. Sheet Thickness 0.8mm

od146667/2019_2020 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.&lt;br&gt;Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006. Sheet Thickness 18mm

od146671/2019_2020 : Supply, Installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.&lt;br&gt;r|n GI volume control duct damper

16.15 : Supplying and Fixing of powder costed extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

od146672/2019_2020 : Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminum with aluminum volume control dampers with anti smudge ring and removable core.

od146674/2019_2020 : Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminum without volume control dampers with anti smudge ring and removable core.

od146670/2019_2020 : Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/ main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.&lt;br&gt;Fire damper

od146668/2019_2020 : Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class &ldquo;O&rdquo;) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.&lt;br&gt;19mm

od135001/2019_2020 : Refrigerant piping of copper tubes/piping,with necessary structural, clamps, supports, bends, elbows, reducers, U-bends, oil return &amp; expansion loops, flare nuts / adaptors / any brass fittings, tee connections etc.with insulation. &lt;br&gt;refrigerant piping of suitable sizes

od135002/2019_2020 : Drain Water Piping P.V.C with nitrile insulation complete with fittings.&lt;br&gt;suitable size as per number of units connected&lt;br&gt;25mm

od135003/2019_2020 : Drain Water Piping P.V.C with nitrile insulation complete with fittings.&lt;br&gt;suitable size as per number of units connected&lt;br&gt;32mm

od135004/2019_2020 : Drain Water Piping P.V.C with nitrile insulation complete with fittings.&lt;br&gt;suitable size as per number of units connected&lt;br&gt;40mm

od135005/2019_2020 : Drain Water Piping P.V.C with nitrile insulation complete with fittings.&lt;br&gt;suitable size as per number of units connected&lt;br&gt;50mm

od135006/2019_2020 : Control Cabling&lt;br&gt;Control cabling with saddles / supports to connect outdoor units with respective indoor units

od135007/2019_2020 : Control Cabling&lt;br&gt;3Cx1.5Sq.mm(Main cabling between socket to machine cabling for respective indoor units.(Socket Considered At 5mtr from the IDU location)

od135008/2019_2020 : Control Cabling&lt;br&gt;3CX2.5Sq.mm-Power cabling between socket to machine cabling for respective indoor units.(Socket Considered At 5mtr from the IDU location)

od135009/2019_2020 : Control Cabling&lt;br&gt;Main Supply from Panel to AHU(AHU Panel is considered at terrace;considered 60mtr cable /AHU)

od135010/2019_2020 : Control Cabling&lt;br&gt;Cabling for corded remote in suitable PVC conduit and chasing on walls.(Considered 5 rmt per m/c)

od135011/2019_2020 : Power Cable of ODU(Considered 5 rmt per m/c from isolator to ODU)

od135012/2019_2020 : Providing &amp; fixing flexible canvas connections.

od135013/2019_2020 : ALUMINIUM DUCTING.&lt;br&gt;Aluminium Ducting as per IS. All duct joints/leakage points to be sealed with silicon sealant. Ducting cost shall include leakage testing as per standards with suitable instruments. Leakage reports shall be submitted. All ducting shall suitably treated with Bacillol before commissioning.&lt;br&gt;22 G ducting

od135014/2019_2020 : ALUMINIUM DUCTING.&lt;br&gt;Aluminium Ducting as per IS. All duct joints/leakage points to be sealed with silicon sealant. Ducting cost shall include leakage testing as per standards with suitable instruments. Leakage reports shall be submitted. All ducting shall suitably treated with Bacillol before commissioning.&lt;br&gt;24 G ducting

od135016/2019_2020 : Acoustic Insulation(For Ductable)(Please confirm whether acoustic is allowed or not for ductable in CT,MRI &amp; Dxray) 10mm thick

od135019/2019_2020 Supply, fixing, testing & commissioning of Non Return Damper made of Casting 1.2 mm thickness ( 18 gauge) Gl sheet Blades are made of 1.1 mm thick extruded aluminum

od135020/2019_2020 : Earthing 8SWG Cu wire (considered 20mtr per ODU)&lt;br&gt;

od135021/2019_2020 : Electric panles with MCB for VRV Outdoor units for supply of power with starter panel&lt;br&gt;MCB-25amps

od135022/2019_2020 : Electric panles with MCB for VRV Outdoor units for supply of power with starter panel&lt;br&gt;MCB-32Amps

od135023/2019_2020 : Electric panles with MCB for VRV Outdoor units for supply of power with starter panel&lt;br&gt;MCB-40Amps

od135024/2019_2020 : Electric panles with MCB for VRV Outdoor units for supply of power with starter panel&lt;br&gt;MCB-63Amps

od135025/2019_2020 : Electric panles with ELCB for VRV Outdoor units for supply of power with starter panel&lt;br&gt;ELCB-25Amps

od135026/2019_2020 : Electric panles with ELCB for VRV Outdoor units for supply of power with starter panel&lt;br&gt;ELCB-32Amps

od135027/2019_2020 : Electric panles with ELCB for VRV Outdoor units for supply of power with starter panel&lt;br&gt;ELCB-40Amps

od135028/2019_2020 : Electric panles with ELCB for VRV Outdoor units for supply of power with starter panel&lt;br&gt;ELCB-63Amps

od135029/2019_2020 : Sequential controller- (1 W +1 SB)

od135030/2019_2020 : Supply &amp; installation of ladder type 16G GI cable tray (for vertical piping) Width - 600mm

od135031/2019_2020 : Supply &amp; installation of ladder type 16G GI cable tray (for vertical piping) Width - 450mm

od135032/2019_2020 : Supply &amp; installation of ladder type 16G GI cable tray (for vertical piping) Width - 350mm

od135033/2019_2020 : Supply &amp; installation of ladder type 16G GI cable tray (for vertical piping) Width - 150mm

od135034/2019_2020 : Ventilation Work&lt;br&gt;Inline Exhaust fan for IDF room-260cfm@20mm w.g. Static

od135035/2019_2020 : Ventilation Work&lt;br&gt;Inline Exhaust fan for IDF room-350cfm@20mm w.g. Static

od135036/2019_2020 : Ventilation Work&lt;br&gt;Inline Exhaust fan for IDF room-400cfm@20mm w.g. Static

od135037/2019_2020 : Ventilation Work&lt;br&gt;Inline Exhaust fan for IDF room-450cfm@20mm w.g. Static

od135038/2019_2020 : Ventilation Work&lt;br&gt;Inline Exhaust fan for IDF room-600cfm@20mm w.g. Static

od135039/2019_2020 : Ventilation Work&lt;br&gt;Inline Exhaust fan for Electrical room-700cfm@20mm w.g. Static

od135040/2019_2020 : Flexible Canvass Connection for Ductable Units

od135041/2019_2020 : Suplly Installation Testing and Commissioning of flexible copper Cable with termination&lt;br&gt;3cx2Sq.mm

od135042/2019_2020 : Validation &amp; Commissioning - Complete validation of operation theaters with particle count and DOP testing of filters. Necessary documentation required for NABH accredition shall be provided by you. For 4 Nos.

od135043/2019_2020 : Return air riser with Al construction(should be powder coating)(Size-700mmx100mmX4000mm(L)

od135994/2019_2020 : Air terminal devices&lt;br&gt;Laminar Flow Station in Aluminium construction with perforated SS plates on front face, complete with supply air collars with Aluminium aerofoil dampers, HEPA filters with mounting and pressure plates. Laminar flow station to be conforming to cleanroom standards. Installation should be carried out in coordination with false ceiling contractor so as to achieve a uniform joint between the ceiling and the flow station. Suitable cutout to be kept in centre for OT light and the same should be closed with a proper blank off plate. Should be provided with a maganhelic gauge for HEPA filters. Size shall be 8&apos; x 6&apos;. HEPA filters shall be mounted in the plenum and not in the collars.

od135995/2019_2020 : Return air perforated grille for risers with removable prefilters.

od135996/2019_2020 : Return air riser with Al construction(should be powder coating)(Size-700mmx100mmX4000mm(L)&lt;br&gt;

od136097/2019_2020 : Supply, fabrication, erection, testing and commissioning of HVAC Panel board fabricated out of 14/16 SWG CRCA sheet, powder coated, compartmentised, free standing, floor mounted, dust and vermin proof with reinforcement wherever necessary fully meeting all the requirement specified in the technical specifications and drawings. Galvanized hardwares with zinc passivation shall be used. TPN switch gear shall be supplied with equally rated neutral link. All indication lamps should be LED type, all MCCBs should be with rotary handle.The panel shall be fabricated as per IS standards and KSEI specifications by a CPRI approved vendor.

HVAC HIGHER SIDE

od135624/2019_2020 : Supply, Installation, Testing &amp; Commissioning of VRV Equipment including pipe pressure testing &amp; flushing with Nitrogen, Charging of Gas &amp; Oil etc.of OUTDOOR UNITS - VRV - Normal - 3 Phase - &lt;br&gt;6 HP

od135625/2019_2020 : Supply, Installation, Testing &amp; Commissioning of VRV Equipment including pipe pressure testing &amp; flushing with Nitrogen, Charging of Gas &amp; Oil etc. of OUTDOOR UNITS - VRV - Normal - 3 Phase - 10 HP

od135626/2019_2020 : Supply, Installation, Testing &amp; Commissioning of VRV Equipment including pipe pressure testing &amp; flushing with Nitrogen, Charging of Gas &amp; Oil etc. of OUTDOOR UNITS - VRV - Normal - 3 Phase - 14 HP

od135627/2019_2020 : Supply, Installation, Testing &amp; Commissioning of VRV Equipment including pipe pressure testing &amp; flushing with Nitrogen, Charging of Gas &amp; Oil etc. of OUTDOOR UNITS - VRV - Normal - 3 Phase - 16 HP

od135628/2019_2020 : Supply, Installation, Testing &amp; Commissioning of VRV Equipment including pipe pressure testing &amp; flushing with Nitrogen, Charging of Gas &amp; Oil etc. of OUTDOOR UNITS - VRV - Normal - 3 Phase - &lt;br&gt;22 HP

od135629/2019_2020 : Supply, Installation, Testing &amp; Commissioning of VRV Equipment including pipe pressure testing &amp; flushing with Nitrogen, Charging of Gas &amp; Oil etc.of OUTDOOR UNITS - VRV - Normal - 3 Phase - &lt;br&gt;40 HP

od135630/2019_2020 : Supply, Installation, Testing &amp; Commissioning of VRV Equipment including pipe pressure testing &amp; flushing with Nitrogen, Charging of Gas &amp; Oil etc. of OUTDOOR UNITS - VRV - Normal - 3 Phase - &lt;br&gt;54 HP

od135631/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units. - cordless remote and all refnet joints. VRV Ductable Units - 2.64TR

od135632/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units. - cordless remote and all refnet joints. VRV Ductable Units - 3.33TR

od135633/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units. - cordless remote and all refnet joints. VRV Ductable Units - 4.12 TR

od135634/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units. - cordless remote and all refnet joints. VRV Ductable Units - 4.75 TR

od135635/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units. - cordless remote and all refnet joints. VRV Ductable Units - 5.5 TR

od135636/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units. - cordless remote and all refnet joints. VRV Ductable Units - 6.5 TR

od135637/2019_2020 : Supply and fixing of INDOOR UNITS - cordless remote and all refnet joints. VRV Ductable Units - 8.2 TR

od135638/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units.- cordless remote and all refnet joints. High Wall Units - 0.83 TR

od135639/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units.- cordless remote and all refnet joints. High Wall Units - 1.05 TR

od135640/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units.- cordless remote and all refnet joints. High Wall Units - 1.33 TR

od135641/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units. - cordless remote and all refnet joints. High Wall Units - 1.65 TR

od135642/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units. - cordless remote and all refnet joints. High Wall Units - 2.07 TR

od135643/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units. - cordless remote and all refnet joints. Ceiling Suspended Cassette Units - 1.33 TR

od135644/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units. - cordless remote and all refnet joints. Ceiling Suspended Cassette Units - 2.64 TR

od135645/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units. - cordless remote and all refnet joints. Ceiling Suspended Cassette Units - 2.07 TR

od135646/2019_2020 : Supply and fixing of INDOOR UNITS - shall include all suspenders, hangers and framework required for installation of indoor units. - cordless remote and all refnet joints. Ceiling Suspended Cassette Units - 3.3 TR

od135647/2019_2020 : Supply of INDOOR UNITS - cordless remote and all refnet joints. Control system - Central Remote Controller

od135648/2019_2020 : Supply and fixing of INDOOR UNITS - cordless remote and all refnet joints. Air Handling Unit-MICU - DOUBLE SKINNED Floor Mounted AHU with minimum 45mm thick PUF panels with thermal break section. Unit shall be floor mounted/ceiling suspended as per site requirement with sandwich type insulated SS drain tray, door limit switches, RA mixing box, prefilter section, coil section coil connected to VRV system, distributor , fan section with forward curved fans with aerofoil blades. AHU shall be mounted on floor with vibration isolators. Unit shall be with factory fitted inlet/outlet aluminium aerofoil dampers. Price shall include all accessories required for healthy working.FA opening shall have filter and insect screen.&lt;br&gt;13.2 TR, 4400 CFM, 450 CFM FA, 125m

od135649/2019_2020 : AHU connected with control box for VRV system for 16 HP

od135650/2019_2020 : Supply and fixing of INDOOR UNITS - cordless remote and all refnet joints. CONTROL &amp; STARTER PANEL FOR AHU WITH VRV UNIT - System shall have three components - Control panel for AHU and ODU control and safety, a Starter panel for AHU and a Remote Controller to be mounted in the OT / suitable location. The control panel shall be complete with all the protection and safety features required for the healthy working of the ODU. The Starter Panel for AHU shall have suitable indicating lights, meters, safety switch gear. The remote controller shall have start/stop facility for both the ODU and the AHU, temperature setting and real time scheduling facility. The cost shall also include the temperature sensor which shall be mounted inside the OT area to sense the actual inside temperature and then control the system accordingly. &lt;br&gt;13.2 TR, 4400 CFM, 450 CFM FA, 125mmESP

od135651/2019_2020 : Supply and fixing of INDOOR UNITS - cordless remote and all refnet joints. Air Handling Unit&lt;br&gt;DOUBLE SKINNED Floor Mounted AHU with minimum 45mm thick PUF panels with thermal break section. Unit shall be floor mounted/ceiling suspended as per site requirement with sandwich type insulated SS drain tray, door limit switches, RA mixing box(not required where 100 % FA is supplied) , prefilter section, coil section coil connected to VRV system, distributor , fan section with forward curved fans with aerofoil blades.Provision of UV lamp inside the AHU section; AHU shall be mounted on floor with vibration isolators. Unit shall be with factory fitted inlet/outlet aluminium aerofoil dampers. Price shall include all accessories required for healthy working.FA opening shall have filter and insect screen.&lt;br&gt;12 TR, 2500 CFM,250 CFM FA; 125mm SP for -Septic OT (100% FA)

od135652/2019_2020 : Supply and fixing of INDOOR UNITS - cordless remote and all refnet joints. Air Handling Unit&lt;br&gt;DOUBLE SKINNED Floor Mounted AHU with minimum 45mm thick PUF panels with thermal break section. Unit shall be floor mounted/ceiling suspended as per site requirement with sandwich type insulated SS drain tray, door limit switches, RA mixing box(not required where 100 % FA is supplied) , prefilter section, coil section coil connected to VRV system, distributor , fan section with forward curved fans with aerofoil blades.Provision of UV lamp inside the AHU section; AHU shall be mounted on floor with vibration isolators. Unit shall be with factory fitted inlet/outlet aluminium aerofoil dampers. Price shall include all accessories required for healthy working.FA opening shall have filter and insect screen.&lt;br&gt;8 TR, 2200 CFM,250 CFM FA; 125mm SP for Surgery OT

od135653/2019_2020 : Supply and fixing of INDOOR UNITS - cordless remote and all refnet joints. AHU CONNECTION KIT FOR VRV SYSTEM&lt;br&gt;16 HP

od135654/2019_2020 : Supply and fixing of INDOOR UNITS - cordless remote and all refnet joints. AHU CONNECTION KIT FOR VRV SYSTEM&lt;br&gt;10 HP

od135655/2019_2020 : Supply and fixing of INDOOR UNITS - cordless remote and all refnet joints. CONTROL &amp; STARTER PANEL FOR AHU WITH VRV UNIT&lt;br&gt;System shall have three components - Control panel for AHU and ODU control and safety, a Starter panel for AHU and a Remote Controller to be mounted in the OT / suitable location. The control panel shall be complete with all the protection and safety features required for the healthy working of the ODU. The Starter Panel for AHU shall have suitable indicating lights, meters, safety switch gear. The remote controller shall have start/stop facility for both the ODU and the AHU, temperature setting and real time scheduling facility. The cost shall also include the temperature sensor which shall be mounted inside the OT area to sense the actual inside temperature and then control the system accordingly.

od135656/2019_2020 : Supply and fixing of INDOOR UNITS - cordless remote and all refnet joints. CONTROL &amp; STARTER PANEL FOR AHU WITH VRV UNIT&lt;br&gt;System shall have three components - Control panel for AHU and ODU control and safety, a Starter panel for AHU and a Remote Controller to be mounted in the OT / suitable location. The control panel shall be complete with all the protection and safety features required for the healthy working of the ODU. The Starter Panel for AHU shall have suitable indicating lights, meters, safety switch gear. The remote controller shall have start/stop facility for both the ODU and the AHU, temperature setting and real time scheduling facility. The cost shall also include the temperature sensor which shall be mounted inside the OT area to sense the actual inside temperature and then control the system accordingly. &lt;br&gt;8 TR, 2200 CFM,250 CFM FA; 125mm SP for Surgery OT

od135657/2019_2020 : Supply and fixing of INDOOR UNITS - cordless remote and all refnet joints. Exhaust Fan Section for Ots&lt;br&gt;Supply of DOUBLE SKINNED Air handling Fan section with thermal break profiles and internal coving. Unit shall be floor mounted with fan section with backward curved fan. AHU shall be mounted on floor with vibration isolators. Unit shall be with factory fitted inlet/outlet aluminium aerofoil dampers. EA opening shall have filter and insect screen.. &lt;br&gt;1800CFM, 50mm SP for Septic OT

od135658/2019_2020 : Supply and fixing of INDOOR UNITS - cordless remote and all refnet joints. Exhaust Fan Section for Ots&lt;br&gt;Supply of DOUBLE SKINNED Air handling Fan section with thermal break profiles and internal coving. Unit shall be floor mounted with fan section with backward curved fan. AHU shall be mounted on floor with vibration isolators. Unit shall be with factory fitted inlet/outlet aluminium aerofoil dampers. EA opening shall have filter and insect screen.. &lt;br&gt;Starter panel for exhaust fan with NO/NC contacts for return air &amp; exhaust air damper.

od135659/2019_2020 : SITC of duct type heater with thyristor control panel KW @ 4400 CFM

od135660/2019_2020 : Supply and fixing DP sensors

od135661/2019_2020 : Controller &lt;br&gt;SITC of controller.Controller should be able to messure the RH &amp; temperature &amp; signal to heater &amp; ODU to maintain the same accordingly. Controller should be able to measure the air flow rate &amp; accordingly gives the signal to VFD.

od135662/2019_2020 : VFD&lt;br&gt;Supply, installing, testing and commissioning of HVAC dedicated VFDs with IP 20 enclosures.

od135663/2019_2020 : Velocity Sensor&lt;br&gt;SITC of duct type velocity sensor with output signal 4-20 mA / 0-10 V.

od135664/2019_2020 : SITC of Temperature &amp; RH Sensor &lt;br&gt;Type: Room Mounted,&lt;br&gt;Temperature Range 0 to 60&ordm;C, &lt;br&gt;Accuracy Temperature: &plusmn; 0.5 degree C. &lt;br&gt;Accuracy RH - &plusmn;2% or better or Enclosure protection class &lt;br&gt;Room Type :IP30 , &lt;br&gt;Sensing enclosure Stainless steel / Polycarbonate Input voltage 24 V DC &lt;br&gt;Output signal 4-20 mA DC to T/RH display, isolated Accessories Mounting Flange and Cable entry gland. Loop powered. Ceiling Mounted. &lt;br&gt;- Transmitter head will be mounted above fall ceiling and Sensing probe below Fall ceiling as per hot spot in room.&quot;

South Indian Constructions Private Limited

Bidder Name

HEATHER CONSTRUCTIONS

South Indian Constructions Private Limited