8415/E8 REPAIR TO FENCING, DRAINS, CLEANING OF SEWAGE LINE, MANHOLES SEPTIC TANKS, SOAKAGE WELLS, WATER TANK CLEANING, CLEANING OF DRAIN PIPES AND CERTAIN MISC B/R WORKS AT RTS AND DEPOT HEMPUR UNDER GE (EAST) BAREILLY

Amount

Dismantling of existing RCC/ Steel /Wooden posts or struts (wood, steel or R.C.C.) any section,concrete ,brick work ,massonery etc . including taking out embedded portion and making good disturbed ground complete all speciified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all speciified and directed

Dismantling fencing wire mesh, any type complete all speciified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum , getting out , returning , filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering , and removing surplus soil to a distance n exc 50 m and making good surfaces in hard/dense soil complete all speciified and directed

M&L for PCC (1:4:8) type D-2 (40 mm grade aggregate) as in foundation, filling and mass concrete complete all speciified and directed

M&L for PCC 1:3:6 Type C-2 (40mm graded aggregate) in foundation filling and mass concrete including surface dressing and leveling. Complete all as specified and directed by Engr-in-charge. Note :- this item used at bottom of chain link fencing.

S&F post and strut in fencing including cutting tops to shape as directed drilling holes notching for wire flat iron fillet ( for securing wire mesh) in incl all necessary drilling bolting,screwing and rivetting conforming to Fe-290 Gd-165 complete all speciified and directed

M&L for Mild steel in flat, round or square bars, in available length , conforming to Fe-410-W(Gde E-250) of quality-B complete all speciified and directed

Supply only mild steel screw bolt ( maching made) with hexagonal or square head at one end and screwed the other with washer n.exc 5 cm long dia bolt 5 to 10mm complete all speciified and directed

M&L for MS round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all speciified and directed

Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

S&F, galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire complete all speciified and directed

M&L preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M & L for two coat of synthetic enamel paint over priming with Red oxide zinc on new or prevously untreated surface of any description not exc 10 cm in width or girth when unconnected with other painting or painted in different tint complete all speciified and directed

M&L preparation of old steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismantling structural steel work including doors, gates and framed truss etc complete all speciified and directed.

M&Lmild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete confirming to Fe410-S.

S&F structural steel work as in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) complete all speciified and directed

M&L for 100 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as sub base floor complete all as specified.

M & L for sand filling under floors or in fdn including watering and consolidation as in bedding layers for laying tiles complete all speciified and directed.

M&L for factory made Machine pressed precast concrete interlocking paver blocks any shape and size confriming to IS 15658-2006 of 60mm thickness coloured chemically treated PCC (ISI Marked ) M-35 grade of desgin & pattern approved by GE as in footpath and filling of joints with fine sand complete all speciified and directed.

S&F rubber moulded decorative designed coloured machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment complete all as specified and directed

M&L in repairs for machine pressesd coloured glazed chequered cement concrete 20cm x 20cm x 25cm thick Glossy finish with mixture of grey and white cement in equal proportions and no pigment set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including screed bed or bedding layer of mortar 20 mm thick, in cement mortar (1:6), complete all as specified and directed.

M&L cement concrete type C-1,1:3:6 ( 20mm graded stone aggregate) as in copings, packing around interlocking paver blocks complete all speciified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floor, aprons etc laid dry or laid and pointed in floor/ footpath complete all speciified and directed.

Labour for except tiles Machine pressed precast concrete interlocking paver blocks any shape and size of 60mm thickness coloured of desgin & pattern refixing in floor/footpath and filling of joints with fine sand complete all speciified and directed.

M & L 16 to 18 mm thick granite(Zed Black colour as approved by GE) stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding,round bull nosing edging and polishing as in kitchen platform/dado/skirting /plateform counter top WHB in cluding cutting holes for oval shape /urinal partitions etc. including 15 mm thick cement screed bed 1:6 CM in horizontal or vertical surfaces including grinding the edges half round and polishing complete all as specified and directed by Engineer-In- Charge.

Demolition of brick work or stone /boulder masonry built in cement mortar including all quoins, arches, pillers etc. but excluding ashlar facings, dressed stone work and precast conc rete articles complete all speciified and directed.

Demolition of PCC of any description and in any position not otherwise specifically provided for complete all as specified and directed

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed

M&L PCC 1:3:6 (type C2) (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all speciified and directed

M&L for brick work with Fly ash' bricks , straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for providing precast cement concrete Type B1 1:2:4 (20mm graded aggregate)as in cover slabs (for manholes, drains etc.) of any size and thickness as required Set in cement mortar 1:4 complete all speciified and directed. Note :- Reinforcement will be measured and paid saperately

M&L mild steel TMT bars 10 mm dia and over cut to length bent to sharp required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) but less than 0.9 mm dia Securing with clips complete all speciified and directed .

Supply & fixing 6 to 8mm dia TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to complete all as specified and directed

M&L, for formwork to sides of concrete Foundations, footings, bases of columns, raft and rft beams, plinth beam, vertical or batter etc. for rough finished surfaces of concrete surfaces all as specified and directed.

M&L PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in coping including weathering, slightly rounded or chamfered angles and throating, as directed and necessary form work complete all as specified and directed.

Demolition and breaking up of drain pipe any dia (salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5 m depth; for foundation, etc. or for shafts, wells, cesspits, manholes,pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out in Soft /Loose soil complete all as specified and directed.

M&L cement concrete 1:4:8 type D2 using 40mm graded crushed stone aggregate in foundation filling as mass concrete complete all as specified and and as directed by Engr-in- Charge.

Returning filling in, Including spreading, levelling,. Watering and well ramming soil in layers not exceeding 25 cm thick, complete all as specified and directed.

M & L for removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate) concrete bed to drain pipe 100mm bore including packing under and haunching against the sides of pipes after laid and tested complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate) concrete bed to drain pipe 150 mm bore including packing under and haunching against the sides of pipes after laid and tested complete all as specified and directed.

M & L 100 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars laid in trenches and jointes complete all speciified and directed

M & L 150 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars laid in trenches and jointes complete all speciified and directed

Demolition of reinforced cement concrete (reinforced cut as required to facilitate to demolition) of any sescription and in any portion not otherwise specified complete all as specified and directed.

M&L cutting into existing manhole for connection of new drain pipe & removing existing drain pipe and cutting out branch channels and making good with packed spun yarn and cement mortar (1:1) and 150 mm bore pipe all as specified and as directed.

M&L for RCC (Nominal Mix) 1:2:4 Type B-1 (using 20mm graded crushed stone aggregate) for slab supported on walls, beams and column in floors, roofs, landings, balconies, canopies, deck slab, manhole cover and in shelves and the like Including all necessary form work complete all as specified and directed. (Note:- Manhole cover should be covered with 3mm thick and 75mm wide GI flate Iron and weld with reinforcement all around and quoted rate should be included the same and also slab repair of septic tank include all necessary cleaning and form work tools and plant should be included in quoted rate)

M&L for Cleaning /clearing blocked sewage line 100mm to 300mm dia (PVC / SGSW / RCC hume pipe) any depth by rodding between manhole to manhole manually and pumping out sludge water from manholes septic tank / soak well etc (where required) including providing trolley mounted pump set with suction pipe of adequate length and minimum 30 mtr delivery pipe including clearing spot blockages of WC, wash hand basins, sinks floor traps, NT and drainage pipes etc with and incl disposal of debris spoils and sludge hygiencially complete all a specified and directed. Notes:- The contractor shall keep the following aspect in mind while quoting unit rates in item above (i) The contractor / his authorise supervisor of the work will report daily at complain cell JE (Civ) Hempur at 0830 hours to receive day to day all complaints. (ii) All sewage complaints must be attended immediatly on receipt but not later than 24 hours. (iii) Recovery (penalty) for not attending complaint beyond 24 hours shall be Rs. 300.00 per compaints per day delayed . (iv)The contractor shall be responsible for safety of workers (v) Contractor has been binded to strictly maintain cleaning of all area under jurisdiction of JE (Civ) Hempur as per direction of ground executive (like cleaning of office area, stores area, cutting of grass by mannually or by spraying of chemical) including cleaning of toilet and office at office area . (vi) The contractor will be responsible to provide a proper dress code to workers and also provide all safetly.

Pumping out of liquid sludge etc, from septic tank/soak well/ manhole complete all as specified and directed.Note- The unit rate quoted under this item shall deemed to include the arrangements of Sewage pump and delevery pipe minimum 60 mtr length and all necessary T&P with man and material and safety equipment etc .

De watering of septic tank of minimum size 10m X 5m X 2.5m with portable pumping set or with suction machine and taking out manually or by mechinically with suction machine, waste material like sludge , mud ,soil , sanitory a material and other dirts etc from inner side of septic tank and outer housing sump by using labour/ equipment and depositing the same waste material at low lying area by digging pits all as , cleaning and washing the surface area of Septic tank with wire brush and removing the algae growth including removal of grass/tree roots including one coat brush of bleaching powder at wall of septic tank and also minor repair like plaster (1:2) or brick work where required or desided by ground executive staff etc all as spedified and directed by engr - in - charge (Note: Brick work will measured and paid in respective items)

M&L for cleaning of RCC or PVC water tank at any height (on accessible / inaccessible of roofs) by removing all scale, dirt, mud etc. from tanks capacity exc 500 ltrs but not exc 1000 ltrs unpluging flushing out and cleaning proporly internally and externally with detergent powder complete, and again cleaning with fresh water including plugging back from mouths of circulating pipes & change if nipple, union etc. complete all as specified and directed

S&F 500 litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) triple layer ISI marked, white coloured, hoisted and fixed in position including 20 mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight- 210 gms) and also including dismantling old water storage tank 500 litre capacity complete all as specified and directed.

S&F 1000 litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) triple layer ISI marked, white coloured, hoisted and fixed in position including 20 mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight- 210 gms) and also including dismantling old water storage tank 1000 litre capacity complete all as specified and directed.

Taking down cement plaster of any description on brick walls including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Material and labour for rendering 15mm thick in cement mortar 1:4 finished fair and even using integral waterproofing compound including Preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all speciified and directed

Material and labour roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust incl. brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and as directed

Material and labour 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate, including finishing surface of concrete topping even and rough as in screed bed complete.

Material and labour for glazed ceramic tiles coloured of size 350 x 450 x 7mm thick in walls etc, set & jointed in neat cement slurry and pointed in white or colours cement to match the colour of tiles over and including 10mm thick rendring in CM (1:4) complete all as specified and directed.

Material and labour for non skid-ceramic tiles coloured of size area of each tile exc.0.06 sqm but not exc . 0.11 sqm (300 x 300 mm) X 6mm thick in floors etc, set & jointed in neat cement slurry and pointed in white or colours cement to match over and including 15 mm thick screed bed in Cement Mortar 1:6 complete all as specified and directed

Material and labour Non skid coloured ceramic tiles 7 to 8 mm thick area of each tils exc.0.11 sqm but not exc 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15 mm thick screed bed in Cement Mortar 1:6 complete all as specified and directed

All as per item No 65 but in skirting, vertical surface dadoes and riser etc. over and including 10mm thick rendring in CM (1:4) complete all as specified and directed.

Material and labour light shed vitrified Ceramic tiles 9mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15 mm thick screed bed in Cement Mortar 1:6 complete all as specified and directed

All as per item No 67 but in skirting, vertical surface dadoes and riser etcover and including 10mm thick rendring in CM (1:4) complete all as specified and directed.

M&L for Endura Non Skid joint free colour tiles 8 to 10 mm thick (square/ rectangular) area of each tiles not exceeding 0.11 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles over and incliding screed bed 15cm in CM (1:6) complete all as specified and directed.

S & F vitreous China wash hand basin, of size 550 x 400mm including brackets, flat back with waste pipe and CI grating including all connections, fixed in repair, complete all as specified and directed.

S&F in repair vitreous China squatting pan 'Orissa pattern', size 580 x 440 mm white, with integral foot rests and cast iron 'P' or 'S' trap 100mm dia, front or back inlet including connections to flush pipe including making good to floor with existing finish complete all as specified and directed.

S&F in repairs vitreous china water closet pan (Pedestal pattern), white with and including plastic water closet seat, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flush pipe, anti syphonage pipe, etc. complete all as specified & directed.

S&F PVC 10 ltr capacity symphonic action type, low level, flushing cistern, white, with inlet, ball valve, float and handle including MS suitable size bracket complete all as specified and directed.

S & F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) including all necessary fixing arragnement with wall complete all as specified and directed.

S&F in repair Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) including all fixing arrangement complete all as specified and directed.

S & F and repair 15 MM bore fency type bib tap chromium plated screwed down high pressure with crutch or capastan handle screwed both ends for iron 15 mm bore pipe or for unions all as specified.

S & F in repair 15 MM bore stop valves cost copper allow chromium plated fency type screwed down high pressure, with crutch or capastan handle screwed both ends all as specified.

S & F and repair 15 MM bore pillar cock fency type cast copper alloy with capastan head,chromium plated, screw down, high pressure, screwed for iron pipe of 15 mm bore with all complete all as specified.

S & F GI tubing of 15mm bore of tube medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floors including Taking up or down existing steel tubing 15 mm bore and connections complete all as specified and as directed.

S&F GI tubing 20mm bore 'medium grade' galvanized with and including all GI fittings and fixed complete to walls and ceiling or laid in floors including Taking up or down existing steel tubing 20 mm bore and connectionscomplete all as specified and directed.

Taking down eaves gutters and rain water pipes(any size or pattern or dia) including all fittings heads shoes, bends necks, etc including removal from site (measured overall fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F in repair PVC (SWR) pipe 110mm bore single socketed with rubber ring joint fixed to walls including mild steel Stack clamps made out of 50mmx 5mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof surface complete all as specified and directed.

S&F in repair PVC (SWR) pipe 75mm bore single socketed with rubber ring joint fixed to walls including mild steel stack clamps made out of 50mmx 5mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof surface complete all as specified and directed.

S&F in repair bend PVC (SWR) with oval excess door 110mm bore complete all as specified and directed.

S&F in repair bend PVC (SWR) with excess door 75mm bore complete all as specified and directed.

S&F PVC (SWR) 75 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) 110 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S S CONSTRUCTION CO (BID ID -3357296)