SPL REPAIRS TO BLDG NO P-02 (OFFRS MESS) AND OTHER MINOR WORKS AT NAA UNDER GE (N) TEZPUR

Amount

Dismantling of Asbestos cement(corrugated, semi corrugated etc.) sheet in roof coverings complete all as specified and as directed.

Dismantling of floor/ wall tiles including cement mortar bedding of any thickness upto PCC/ RCC/brick surface and rubbish off the premises, complete in all respect all as specified and directed.

Dismantalling of cement concrete (unreinforced) in ground floors and pavings not exceedings 15 cm thickness (below or above ground level), complete in all respect as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and as directed

Taking down cement plaster on stone/brick/concrete surfaces including racking out joint, hacking for key, scrubbing down with water etc, complete all as specified and as directed.

Demolition and breaking up drain pipes 75 mm/110 mm bore dia (Salt glazed ware, PVC or Reinforced concrete) set in cement mortar, complete in all respect as specified and directed.

Material and labour for brick work with sub-class "B" old size bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) including dismantling of existing brick work built in cement mortar complete in all respect as specified and directed.

M&L for half brick work with subclass ‘B’ old size bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:4) including dismantalling of brick work built in cement mortar in any position, complete in all respect as specified and directed.

S & F second class hardwood plain,solid ,straight,chowkats and frames,wrought, framed rebated on the solid ,rounded or chamfered,put together with glue pinned at joints, complete in all respect as specified and directed.

M & L for cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs, slab staging for water tanks, filling of pressed steel door frame, fixing of hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formworks complete all as specified and directed by Engineer- in-charge.

S&F of framed work as in guard bars ,grills ,gratings and similar work confirming to FE 290,Gde-E-165 Etc complete all as specified and directed.

S & F mortice lock, vertical type, mild steel, 2 levers, vertical type, 100 mm size including protective coating of painting fixed in position complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular/hollow section, channel or flat sections) including distance pieces, cleats etc. using FE-410W (Grade E-250 quality "A") complete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone slab flooring of size not less than 500x500mm over 20mm thick cement mortar (1:6) cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M & L for 20 to 25 mm thick machine cut Kota stone in risers of steps, skirting, dado and pillar laid on backing layer of 10 mm thick in cement mortar 1:3, laid and jointed, pointed with grey cement slurry, mixed with pigments to match the sheds including rubbing and polishing complete all as specified and directed.

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed.

S&F coloured 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strenght of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws with bitumen washer to truss members of any material, complete in all respect as specified and directed.

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed.

Supply and Fix exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping , of grid size 600x600mm comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 24x38x0.70mm with 4mm dia GI wire as suspender and including 4mm thick decorative pre -painted non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/wooden truss of any type including dismantling of existing false ceiling boards, complete all as specified and directed.

M&L for non skid ceramic (coloured) tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Providing and laying coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.08 sqm but not exceeding 0.15 sqm, in skrting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, complete in all respect as specified and directed.

Material and labour for any colour of granite stone without white spots Granite stone slab 17-19mm thick, as in floor, dado, steps, laid over and including screed bed 15mm thick in cement mortar (1:6), jointed and pointed with white cement mixed with pigment to match the shade of stone including cutting, rubbing and polishing surface, including cutting for wash hand basin, sink, gas pipe hole etc., to the entire satisfaction of the Engineer-in-Charge complete in all respect as specified and directed.

Taking down of existing roof treatment from roof and terrance, roughening surface of old concrete roof by picking, sweeping clean and washing down with water to remove dust, etc and applying roof treatment with the following specification:- (a)Applying cement slurry over concrete surfaces @3kg/sqm. (b)Rendring 15mm thick in cement mortar (1:4) mixed with water proffing compound as per manufactures instruction on cleaned concrete surfaces of roof and finishing the surfaces fair and even including curing the plastered surfaces for 7 days by ponding of water over the roof, (leveling course). (c) Applying evenly one coat of cold bituminous primer conforming to [email protected] liter per square metre on the cleaned plastered surfaces (d) Applying evernly one coat of blown hot bitumen of grade 85/25@ 1.20 Kg per square metre on primed surfaces. (e) Applying a layer of APP based polymeric membrane, 3mm thick (minimum) weighing 3.50 Kg per square metre reinforces) with polyster non woven fabric wighing not less than 160 gms per square metre by torch application. The overlap shall be not less than 100mm on transverese direction and 75mm on longitudinal direction and sealing overlsaps. (f) Applying evenly one coat of aluminium paint @ 0.10 litre per square metre over the APP based polymeric membrane.

M & L including installation and testing for U type modular kitchen of size 4500 X 2700 with following accessories, complete all as specified and directed. (a) Handle type - SS handle fancy type 128mm size- 22 Nos (b) Carcase- Prelaminated ply, 18-19 mm thick ply over 0.9 mm thick decorative C1 of surface finish, colour and pattern as approved by GE. (c) Kitchen chinmey of 60cm, 1250 m3/hr. suction motor FRP, 180watt wall mounted 3 speed setting with filter less auto technology with motion sensor and touch control curved glass - 01 Nos (d) Basket (i) Stainless steel designer cup and saucer basket of size 530mm wide, 505 mm depth and 100mm height - 01 No (ii) Satinless steel perforated peep hole cutley basket of size 530mm wide 505 mm depth and 100 mm height - 01 No (iii) Stainless steel designer plain basket of size 530mm wide 505 mm depth and 150mm height - 01 No (iv) Stainless steel pull out basket of size 160mm wide 505 mm depth and 530mm height- 01 No (v) Stainless steel designer thali/ plate basket comb of size 530mm wide 505mm depth and 200 mm height - 02 Nos (e) Stainless steel magnetic catcher of size 5.08 X 2.54 X 2.54 cm for cabinets and shelves - 34 Nos. (f) Channel - Soft closing telescopic channel 18 " size (45 kg) suitable for basket/ drawer. (g) Auto closing consealed hinges 9.5 crack for half overlay doors with 95 degree opening angle 14-32 mm zinc coating - 68 Nos

S&F Itched toughe and glass 12mm thick for partition and door fixed with stainless steel hinges ,handle and stainless steel fixing cleat complete in all respect as specified and directed.

M & L for rendering/plastering 15 mm thick in cement mortar 1:4 on faces of brick or concrete surfaces and finished the surface even and smooth without using extra cement complete in all respect as specifified and directed.

M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of of wall in cement mortar (1:6), finished even and smooth without using extra cement, complete in all respect as spefied and directed.

M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of wall in cement mortar (1:4), finished even & smooth without using extra cement, complete in all respect as speicifed and directed.

Supply only integral water proofing compound complete all as specified and as directed.

S&F in repair 15 mm bore GI tubes medium grade, galvanished with all fittings fixed complete to walls and ceiling or laid in floors complete in all respect as specified and directed.

S&F in repair 20 mm bore GI tubes medium grade, galvanished with all fittings fixed complete to walls and ceiling or laid in floors complete in all respect as specified and directed.

S & F in repairs 20 mm gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed to pipe complete all as specified and directed.

S & F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. or for window grill of appd size and shape including fixing with aluminium "U" shape section for fixing etc. complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium three tier window frame including necessary joining cleats, of Jindal section No 20832 or equivalent section of appd make of 1.5mm thick complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F of powder coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in ewach door, hinges, anodised aluminium snap beading screws etc. complete all as specified and directed.

S&F aluminiu door floor spring,Suitable for left-right opening & single-door,double door two direction opening, 90° hold open, Suitable for the size of door 950 x 2100mm complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/ Chowkhat of size 65 X 100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk / wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face)& 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite / borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/ss dash fasteners of required dia and length complete as per direction of enineer-in-Charge (M.S. hold fast/lugs or SS dash fastener shall be paid for seperately) Note: For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F in repair Single unit wash down water closet pan white including plastic water closet seat, white, Single unit with flat bottom,(Make- Jaquar WHT-6851S110PP, Hindware "Starc" P-SW) complete in all respect as specified and directed.

M & L for solid PVC wall lining consisting of 5 mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed.

M & L for 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed.

S & F powder coated aluminium sliding window with/without sash bars, aluminium sections of thickness 2mm including necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No grade), powder coated aluminium snap beading, screws, center grooved stainless steel ball-bearing double roller 2 position height adjustment, sound/dust brush, recessed handle with locking arrangement complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F 75 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed.

S & F 100 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed.

Supply and fix solid PVC door frames of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube all as per specification & drawing complete all as specified and directed by Engineer in charge.

S & F 35 mm thick factory made moulded door shutter consisting of solid core single leaf flush door of 30 mm thickness, lipped with 15 mm (5 mm X 3) thick X 30 mm width on one stiles and top rails & 10 mm (5 mm X 2) thick X 30 mm width on the other stiles & bottom rails. The inner panel laminated with 2 mm thick termite proof, water proof, and fire resistant moulded PVC sheet with 2, 4, 6 raised panel design in different prelam colour on one side after routing the moulded design on flush door & 2 mm prelam PVC sheet on other side using rubber adhesive on the PVC lipping etc. complete as per direction of Engineer-in-charge, manufacturer’s specification.

S & F 35mm thick, second class HW, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete in all respect as specified and directed.

S & F 4 mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in square not exceeding 0.5 sqm in each pane complete all as specified and as directed.

Supply & fix sheet glass, ordinary quality, 4 mm thick and glazed with oil putty or fixed with beads in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

S & F flush door shutters, 30 mm thick, solid core of block boards construction, MR grade, commercial type with stiles, rails and lipping of timber as given in Group 2A and Group 2B of Annex B of IS 2202 (Part 1): 1999, face panels of plywood of type I as per IS 1328: 1996 on one side and plywood as per IS 710: 2010 on other side, internally lipped complete all as specified and as directed.

S & F aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 200 mm long, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed.

S & F cast aluminium alloy handle, cast type, 125 mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.

S & F mild steel sliding door bolts, type I (plate type), size 250 mm, stove enamelled black finish to back plate, straps and staple, electroplated finish with nickel and chromium to hasp and bolt, bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

S & F mild steel door spring of rat tail type of size 300 mm, bright finish including roller and roller plate complete all as specified and as directed.

S & F 20 mm dia harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc. complete all as specified and as directed.

Dismantling water tanks of any size and removing to store and S & F rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) of 1000 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe spouts for connecting inlet, outlet, over flow and washout pipes all as specified and as directed.

S & F PTMT ball valve high pressure 20mm bore with epoxy coated aluminium rod & high density plastic ball screwed for iron/CPVC pipe/fittings complete all as specified and directed.

S & F in repairs 15 mm nominal size, nonrising spindle type fancy concealed stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed

S&F in repair vitreous chinaware sqatting pan of size 580 x 440 mm, 'ORISSA PATTERN' with new PVC 'P' or 'S' trap bedded in cement concrete (excluding flushing cistern and flush pipe) with integral foot rests, complete in all respect as specified and directed.

S&F Vitreous China urinals, full stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern complete all as specified and directed.

S & F in repairs 10 litres capacity, low level, syphonic type, white, plastic flushing cistern as per IS 7231: 1994 with inlet, ball valve, float and handle including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed.

M & L for PVC connections 15 mm size with PTMT nuts of length 300/450 mm complete all as specified and as directed.

S & F in repairs 15 mm nominal size, nonrising spindle type fancy angle stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed.

S & F 25 mm nominal size, screw down bib taps, cast copper alloy body and body components with crutch handle, nickel-chromium plated finished complete all as specified and as directed.

S&F in repairs short body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed.

Supply and fixed in repair 15mm bore, cast ABS body, CP finish, shower rose of size 125 mm dia and shower arm of cast copper alloy CP finished, fixed to iron pipe/fiitings complete in all respect as specified and directed.

S & F brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and as directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with brass chromium plated bracket guard and railing 60 cm long complete in all respect as specified and directed.

S & F in repair wash hand basins, vitreous China of size 550 x400mm (flat back or angle back type), including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32mm dia bore waste fitings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement, PVC waste pipe including 15mm bore dia fancy type CP finish Pillar tap, cast copper alloy with capstan heads, screwed down high presuure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipes complete all as specified and directed.

M&L for coloured vitrified ceramic tiles, light shade 9-11 mm thick in floor, area of tile not exc 0.36 sqm each set and jointed in neat cement slurry and pointed with white cement with pigment to match the shade of tile over and including screed bedding 15 mm in cement mortar (CM) 1:6, complete in all respect as specified and directed.

M&L for coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skrting/ dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 10 mm thick rendering in cement mortar (cm) 1:4, complete in all respect as specified and directed.

S & F PVC (SWR) nahani trap of 75mm outlet dia fixed with PVC 150X150mm size openable at center grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S & F PVC (SWR), type A as per IS 13592: 2013 single socketed rain water pipes in any length with rubber ring joints, 110 mm dia, fixed to walls complete all as specified and as directed.

S & F PVC (SWR), type A as per IS 13592: 2013 single socketed rain water pipes in any length with rubber ring joints, 75 mm dia, fixed to walls complete all as specified and as directed.

S & F PVC (SWR), type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 110 mm dia, laid in trenches complete all as specified and directed.

S & F PVC (SWR), type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 75 mm dia, laid in trenches complete all as specified and directed.

S & F PVC (SWR) Tee(87.5⁰) single, 110 mm dia with inspection door conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge.

S & F PVC (SWR) Tee(87.5⁰) single, 75 mm dia with inspection door conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge.

S & F PVC (SWR) bends without inspection door (any angle), 110 mm dia conforming to IS 14735: 1999 complete all as specified and directed.

S & F PVC (SWR) bends without inspection door (any angle), 75 mm dia conforming to IS 14735: 1999 complete all as specified and directed.

S & F PVC (SWR) vent cowl, 110 mm dia conforming to IS 14735: 1999 complete all as specified and as directed.

S & F PVC (SWR) vent cowl, 75 mm dia conforming to IS 14735: 1999 complete all as specified and directed.

Supply and fixed unplasticised PVC (SWR) Gully trap 125/110 mm, setting and jointing with solvent cement complete in all respect as specified and directed. Make: Supreme, Prince, Oriplast.

M&L for precast RCC, type B-1, 1:2:4 (using 20 mm crushed and graded stone aggregate) as in manhole covers/ cover slabs or of similar type slab works, etc. incl necessary formwork and loading/ unloading of the same and fixed in position, complete in all respcet as specified and directed.

M & L for RCC M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 10 cm but not exceeding 20 cm wide for rough finished surfaces of concrete complete all as specified and as directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height. Complete all as specified and as directed.

M & L 75 mm thick plain cement concrete M10(Nominal Mix) using 40 mm nominal size graded stone aggregates finished surface even and fair without using extra cement including necessary expansion joint and filling compound as in plinth protection all as specified and as directed.

M&L for preparation of old decorated plastered surface of wall after complete removal of existing treatment and applying two coats of weather coat over 2 mm thick wall care putty (in two layers) over a coat of primer including preparation of surface, complete in all respect as specified and directed.

Material and labour for complete removal of existing treatment on wall and applying two coats of oil bound distemper and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2mm thick (in two layers), wall care putty complete in all respect as specified and directed.

M&L for preparation of old decorated plastered surface of ceiling and applying two coats of oil bound distemper including filling of voids with wall care putty on plastered surface including complete removal of existig treatment, complete in all respect as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of weather coat over 2 mm thick wall care putty over a coat of primer including necessary preparation of surface, complete in all respect as specified and directed.

Material and labour for preparation of newly undecorated plastered surface of wall and applying two coats of oil bound distemper and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2mm thick (in two layers), wall care putty complete in all respect as specified and directed.

S & F powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

M & L for preparation of new or previously untreated wood or wooden surfaces, of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Preparation of newly or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge

M&L for preparation of old decorated wood and wood based surface of any description not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint, complete in all respect as specified and directed by Engr-in-Charge.

M & L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with one coat of creosote complete all as specified and as directed.

Preparation of old or previously untreated steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

M & L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M & L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

M & L for rendering/plastering 15 mm thick in cement mortar 1:6 on faces of brick or concrete surfaces and finished the surface even and smooth without using extra cement complete in all respect as specifified and directed.

S & F factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles) with wood free EPS core, with 2, 4, or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

S & F 75 mm size butt hinges, extruded aluminium alloy with brass wire pin, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996, hinge designation 125A22 as per IS 205: 1992 complete all as specified and as directed.

S&F 20mm dia tubular towel rail 600mm long of cast copper alloy, chromium plated with end brackets complete in all respect as specified and directed.

S & F aluminium alloy handle, cast type, 150 mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.

S & F mild steel sliding door bolts, type I (plate type), size 300 mm, stove enamelled black finish to back plate, straps and staple, electroplated finish with nickel and chromium to hasp and bolt, bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

M & L for screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and as directed.

M & L for coloured non - skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement with pigment to match the tile colour complete in all respect as specified and directed.

M&L for coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile colour complete in all respect as specified and directed.

S&F in repair Health faucet cast coper alloy CP finish 15 mm dia fancy type with brass plated flexible hose and wall hook, 1.00 mtr complete, in all respect as specified and directed. Make:- Jaquar, Hindware Cat part No F-160002

S&F CP finish cast copper alloy, two way bib cock complete in all respect as specified and directed.. Make:- Jaquar cat part No SQT-512ANKN, Hindware Cat part No F-330004SCP

S&F Vitreous China urinals, full stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern complete all as specified and directed.

S&F in repair cast copper alloy CP finished, single level wall mixer with provision of hand shower, hand shower dia 105mm round shape single flow with air effect(ABS body & face plate chrome plated) with rubit cleaning system complete in all respect as specified and directed. Make:- Jaquar

S&F 350 x 450 mm size, PVC mirror cabinet complete all as specified and directed. Make:- Prayag cat Part No 551, CERA, Hindware, Jaquar

S & F rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) as per IS 12701: 1996 of 1000 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes all as specified and as directed.

S & F powder coated aluminium ventilator with half portion louvered (adjustable)with 4mm thick glass in louver and balanced portion fixed 4mm thick frosted glass glazing including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings complete in all respect as specified and directed.

S & F PVC (SWR) Tee(87.5⁰) single, 110 mm dia without inspection door conforming to IS 14735: 1999 complete all as specified and directed.

S & F PVC (SWR) Tee(87.5⁰) single, 75 mm dia without inspection door conforming to IS 14735: 1999 complete all as specified and as directed.

Supplying & laying in trenches 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Supplying & laying in trenches 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

S & F 20 mm gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed to pipe complete complete all as specified and as directed.

S&F Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with brass chromium plated bracket guard and railing 60 cm long complete in all respect as specified and directed.

S&F in repair table top wash hand basins (WHB), vitreous china of size 500x400 mm x 150 mm ,Waste coupling 32 mm SS and PVC waste pipe including 15 mm bore dia fancy type CP finish swan neck basin mixer, cast copper alloy with capstand heads, screw down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screw for iron pipes complete in all respect as specified and directed. Make:- Jaquar, Cat Part No. JDS-WHT-25909 (TT WHB), Cat Part No FLR-CHR-5167NB (Swan neck basin mixer) including 20mm granite table top size(1.0 mtr x 0.6 mtr) and cabinet front side views material made by pre laminated 18 mm thick HDHMR board for long life.2 drawers and 1 door space.hardware ss auto closed hinges joints door diamond shape drawers handle,ss drawers channels for smoothly open and close the drawers complete all as specified and directed.

S&F 15mm bore dia CP finish , bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron/CPVC pipe/fittings or for brass ferrule including cup washer/flange complete all as specified and directed.

S & F 15 mm nominal size, nonrising spindle type fancy angle stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed.

S & F toilet paper holder of vitreous china, box type, white fixed to walls with chromium plated brass screws complete all as specified and as directed.

M & L for liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 105 gms) complete all as specified and as directed.

S&F tower ring of copper alloy CP finished complete all as specified and directed. Make:- Jaquar cat part No AEC-1121, Make Hindware cat part No F450023

Supply and fix PVC SWR Nahani/ Floor trap plain with grating including jointing with solvent cement, dia of outlet 75 mm, water seal minimum 50 mm, complete all as specified and directed by Engineer in charge.

Taking down carefully aluminium / copper point wiring any type for one light , fan, socket power point or buzzer controlled by one switch complete including fitting / fixtures such as switches, ceiling roses, holder, socket etc; and making good disturbed surfaces of walls, ceilings etc complete all as specified and as directed.

Taking down main switches and DBs of any type and make including wooden board/ junction box and making good disturbed surfaces of wall , floor etc complete all as specified and as directed.

M&L for point wiring with 1.5 sqmm (nominal area) FRLSH PVC insulated multi stranded copper conductor single core wire/cable including non metalic PVC conduit (ISI marked MMS) medium grade of size 25 mm dia concealed in wall or over ceiling(at site requirement), complete with all accessories and all as specified including 1.5 Sqmm FRLSH PVC insulated sheathed solid multi stranded copper conductor cable/wire for continoues earth wire in green colour and connected to earth dolly for ceiling fan point / light point /exhaust fan point / bell point controlled by one switch. Note:- 1. M&L for cutting chases on walls / ceiling and making good disturbed surfaces including finishing with cement mortar (1:3) etc; are deemed to be included in the quoted rate. 2. Cost of PVC conduit,Modular metal flush box , modular white cover plate, etc as required shall be deemed included in quoted rate. Make of cable: Polycab/Finolex/Havells/KEI Make of Conduit :- Presto plast/ Richa

All as per item 137 above but for 3 pin 5 Amps switch socket combination on independent board with 1.5 sq mm copper cable complete all as specified and directed.

All as per item 137 above but for 5 Amps socket point on the same board controlled by one switch complete all as specified and directed.

All as per item 137 above but for 3 pin 15/16 Amps switch socket combination on independent board with 4.0 sq mm copper cable complete all as specified and directed.

S & F modular switch, 1 way, 6/10 Amp SP, 1 module complete all as specified and as directed.

S & F modular switch, 1 way, 16 Amp SP, 1 module complete all as specified and as directed.

S & F Modular fan step regulator, 120 W, 2 modules complete all as specified and as directed.

S&F for ceiling rose surface bakelite 3 phases polycarbonate isolated body complete in all respect as specified and directed.

S & F Modular Socket 6 A 2/3 pin combined , 2 module complete all as specified and directed.

S & F Modular Socket 6 A /16 A-2/3 pin combined 2 module complete all as specified and directed.

S&F in replacement LED batten luminaires, 20 watts,CCT 5700 K (4 feet), made of anodised extruded aluminium housIng, with high transmissivity diffuser, high lumen output, with suitable integrated electronic driver, and operated in single phase, 230 volts, 50HZ, all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable of size 23/0.0076, from connector and ceiling rose, complete all as specified and directed. Make Wipro/Philips/CG

S&F in replacement LED batten luminaires, 10 watts,CCT 5700 K (2 feet), made of anodised extruded aluminium housIng, with high transmissivity diffuser, high lumen output, with suitable integrated electronic driver, and operated in single phase, 230 volts, 50HZ, all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable of size 23/0.0076, from connector and ceiling rose, complete all as specified and directed. Make Wipro/Philips/CG

S & F in replacement LED recess mounted (2'x2' size flat panel) luminaire which provide soft light and glare free symmertical illumination suitable for armstrong/grid ceiling of 36Watt,(Lumen output not lessthan 3600) complete all as specified and directed.

Supply and fixing in replacement decorative wall light fixture made up of polycarbonate and including retrofit LED (spira B-22 base) 9/10 W complete all as specified and as directed.

S&F in replacement new generation energy saving and environmental friendly long life 25 W LED wall/building security light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having top Opening seperate driver compartment with IP66 protection and impact resistance of IK07 including necessary brackets (made out of suitable bore GI pipe light grade appx 0.6 meter long bend to shape) nuts, bolts, etc fixed on walls with MS clamp complete all as specified and directed . Make:- Philips/ Wipro / Crompton.

M&L for sheet metal enclosure for TPN DB-VTPN 4 way 415 V, double door , 250 A copper bus bar , IP 43 , including 100 Amp MCCB as incomer as flush mounted complete all as specified and as directed.

M&L for sheet metal enclosure MCB DBs SPN , 12 way 240 V, with 100 A rated bus bar , double door, IP 43 as per IEC 61439-3 , suitable for flush mounting and surface mounting complete all as specified and as directed.

S&F Isolator/ MCB single pole (SP) 5 to 40 Amps, 240 volts , C curve , AC , 50 Hz ,10 kA complete all as specified and directed.

S & F SPN sheet metal enclosure with two pin earth plug socket complete with single pole & neutral MCB 20 Amp complete all as specified and directed.

M & L for MCB SPN 32/40 Amps, 240 volts , 10 kA ISI marked as per IS/IEC 60898-1 2002 , C -curve , IP 20 including taking out complete all as specified and directed.(Make :- Legrand series 4086 17 to18 or equivalent in L & T / Schnieder)

M & L for sub main wiring with two single core FRLSH, PVC insulated unsheathed , 1100 Volts grade, copper cable 4 sqmm stranded conductor and drawing through PVC conduit (MMS ISI marked) of suitable size with accessories including continus earth wire FRLSH,PVC insulated unsheathed 1100 volts grade, cable 4 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring and making good disturbed surface matching with the existing shade/tint. Note :-(i) One run of conduit, two runs of cable and one run of earth wire shall be measured and paid as one unit.

M & L for sub main wiring with two single core FRLSH, PVC insulated unsheathed , 1100 Volts grade, copper cable 6 sqmm stranded conductor and drawing through PVC conduit (MMS ISI marked) of suitable size with accessories including continus earth wire FRLSH,PVC insulated unsheathed 1100 volts grade, cable 6 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring and making good disturbed surface matching with the existing shade/tint. Note :-(i) One run of conduit, two runs of cable and one run of earth wire shall be measured and paid as one unit. Make of cable: Polycab/Finolex/Havells/KEI Make of Conduit :- Presto plast/ Richa

M & L for three phase sub main wiring(as per SSR schedule) with single core FRLSH, PVC insulated unsheathed , 1100 Volts grade, copper cable 10 sqmm stranded conductor and drawing through PVC conduit (MMS ISI marked) of suitable size with accessories including continus earth wire FRLSH,PVC insulated unsheathed 1100 volts grade, cable 10 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring and making good disturbed surface matching with the existing shade/tint. Note : 3 run single copper FRLSH cable of size 10 sqmm for each phase , 1 run 10 sqmm for neutral & 1 run 10 sqmm for earth in same conduit will drawn.

Taking down ceiling fan any type/ size from hook and dismantling cable and blades and bring in to contractor store for repair and hanging ceiling fan in position after repair, greasing etc. with existing flexible copper cable complete all as directed. (rewinding of fan, painting and spare parts required shall be deemed to be included in the quoted rate)

Taking down exhaust fan any type/ size from wall and dismantling cable and blades and bring in to contractor store for repair and re-fixing exhaust fan in position after repair , greasing etc with existing flexible copper cable complete.

M & L for Earthing with galvanised steel pipe electrode, 40 mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 32 x 6 mm strip galvanised iron strip all as shown in Plate No. 2 ( SSR Part-1) to the earthing test point all as specified and indicated , necessary excavation any type of soil, CI chamber cover 10 mm with 6 mm rod , wire mess, funnel, test point, 40 mm dia GI protection pipe medium grade etc complete and testing on completion all as specified and directed by Engr-in-charge (25 x 4 mm strip lead upto 7.5 RM will be included in the item rate . (Note :- Fresh agriculture soil / black dirt or soil with a high organic conten will be used for filling the dug as required when rocky /sandy soil found at site to achieve the desired resistance from out side without any extra cost.

Supply, Laying, testing & commissioning of UG LT cable XLPE insulated screened PVC bedded, galvanized steel strip armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 70 Sqmm x 3.5 core including connecting the cables at both ends by providing suitable size aluminium lugs at the termination ends and necessary saddle clamp all as specified and directed by Engg-In-charge.

Supplying & fixing to walls and ceilings or laid in floors 80 mm nominal bore, light grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or water supply pipes lines etc or not exceeding 10 sqm on plan and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed.

Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

M&L laying well burnt old size bricks, sub calss "B" bricks, straight or curved on plan, laid flat with width equal to length of brick, laid dry over electric cablefor protection all complete all as specified and directed.

M&L for river sand, washed and screened dry for cushioning to under ground cable in tenches below and around under ground cable including spreading and levelling complete as specified and directed.

M&L for boring manually (upto 80 mm dia pipe) under road/path for laying of cable complete all as specified and directed.

Supply, install, testing & commissioning of LT busbar chamber of size (0.1x0.10x0.60) m CPRI approved, outdoor type, factory made fabircated to CRCA sheet of 3.15 mm thickness, angle iron of size 50X50X6mm thick of length 0.6 m from pcc, frame work and tee section (frame) of suitable size double door front/rear opening and locking arrangement, floor mounted on plateform of suitable size, Al bus bar chamber (enclosed) incl rust free spray painting with two coat of synthetic enamel paint over a coat of red oxide primer mounted on PCC blocks, fixed with grouted bold, nuts and washer and making complete connection including MCCB 160 Amp as incomer in all recpects as diected by engr-in-charge comprising of following accessories:- BUS-BAR & INTERNAL CONNECTIONS: The bus-bars shall be made up of 04 Nos aluminium 250 A rated , duly insulated with 1100 V grade standard colour coded PVC sleeves & rigidly mounted on suitable sized "F" class insulators of non-hygroscopic fiber bushes and brass screws min-08 Nos, non-combustible, all internal connections from main bus-bars to switch gears etc. PROVISION FOR CABLE ENTRY : The provision for cable entry/exit shall be provided in the bottom for both incoming & out-going cables. INSTRUMENTATION SYSTEM : (a) Indicator lamp with integral circuit (230/240V) & cluster LED (Red, Orange, Blue) - 01 Set. (b) 3 Ph Digital Voltmeter CI 1.0 - 01 No (c) Danger notice plate of size 20 x 15 cm of 1.6mm thick mild-steel sheet, vitreous enameled white, with letters, figures and conventional skull and bones in signal-red colour and fixed with MS clamps, bolts and nuts of approved size, for LT conforming to IS-2551 - 01 Nos. NOTE : 1) Design / Drawing / BOM of the LT Busbar panel board showing the dimensions incl accessories is to be obtained from panel board manufacturer / supplier & is to be got approved from GE before placing final order to the manufacturer/Supplier. 2) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates. NOTE : 1) Design / Drawing / BOM of the panel board showing the dimensions incl accessories is to be obtained from panel board manufacturer / supplier & is to be got approved from GE before placing final order to the manufacturer/Supplier. 2) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates.

All as per item 137 here-in-before for 3 pin 5 amps switch socket combination on indpendent board with 1.5 sqmm capper cable complete all as specified and as directed.

All as per item No. 137 here-in- before but for 3 pin 15 Amps switch socket combination on independent board with 4.0 sq mm copper cable

S & F sheet metal enclosure for MCB DB, SPN, 240 Volts, 200 amps rated busbar, 4 way metal double door enclosure made up of CRCA sheet steel, powder coated, IP 43 , insulated bus bar complete all as specified and directed by Engr-in-charge.

S & F isolator SP, 5 to 32 A, 240 V complete all as specified and as directed.

S&F Isolator/MCB DP 32 Amps, 240 volts , C Curve, AC , 10 kA complete all as specified and directed.

Supply and fixing LED light fitting mirror/batten type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing LED luminaires, 20 watts, lumen output not less than 2000 (4 feet), made of anodised extruded aluminium housng, with high transmissivity diffuser, high lumen output not less than 2200, with suitable electronic driver, and operated in single phase, 230 volts, 50HZ, all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable of size 23/0.0076, from connector and ceiling rose, complete all as specified and directed. Make:Philips/Havells/Crompton/Bajaj

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm. complete including provision of PVC insulated copper multi starnded three core flexible cable for making necessary electrical connections from ceiling rose to connector all as required at site. Necessary hole cutting properly and fixing deemed to be included in quoated rate no extra cost willbe provided.

M & L for sub main wiring with two single core FRLSH, PVC insulated unsheathed , 1100 Volts grade, copper cable 4 sqmm stranded conductor and drawing through PVC conduit (MMS ISI marked) of suitable size with accessories including continus earth wire FRLSH,PVC insulated unsheathed 1100 volts grade, cable 4 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring and making good disturbed surface matching with the existing shade/tint. Note :-(i) One run of conduit, two runs of cable and one run of earth wire shall be measured and paid as one unit. Make of cable: Polycab/Finolex/Havells/KEI Make of Conduit :- Presto plast/ Richa

Supply and fix electric water heater storage type steel/ABS body(as directed by Engineer-In-charge) with glass lined stainless steel inner tank capacity 25 litres, heating element of 2 KW, BEE 5 star rated with all accessories such as safety valve , thermostat , NRV , connection pipe , nut bolt with metalic anchor fasterner etc for fixing on wall & testing complete all as specified and directed by Engineer-In-charge. Make Crompton/Havells/USHA/Jaquar of 25 Ltr capacity Note:1. Warranty of 2 year on geyser and 07 year on geyser tank shall be submitted by the contractor.

Supply and fixing single pole and neutral enclouser with a two pin and earth plug and socket complete with one pole MCB 20 Amps complete all as spd and directed.

M&L for Earthing complete with GI plate electrode of size 600x600x6 mm thick buried directly in ground with earth pit not less than 3 meter deep below ground level with top edge of plate not less than 2.4 meter below normal ground level connected to GI earth wire 4mm dia earth lead up to 7.5 mtr by means of nuts, bolts, check nuts, washers of tinned brass, protected by galvanized iron pipe 20mm bore (Medium grade) all as directed including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 42 x 42 x10cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 30 cm long, bent to shape as lifting handle, funnel, wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering,including charcoal or coke and salt in alternate layers and filling earth pit with fresh vegetable soil below GI plate and above upto ground level as required and necessary earth work in soft/loose soil complete all as shown in electrical plate No 5 of SSR Part I including testing on completion all complete as specified and directed.

M/S Bharat Construction Co.

M/S SHYAMAL SARMAH

M/S JIWA SINGH S GILL

M/S RHINOTECH BUILDERS

Anil Kumar Sarmah

M/S Barua Enterprise

M/S UDIPTA KUMAR BORAH