Fabrication and erection of 2 Nos of shutter near Thiruvallom Parasurama Temple and Electrification of hoisting mechanism

Amount

Dismantling the existing 2 Nos of shutter and providing a new RCC platform for hoist unit

OD5434/2023-2024:Clearing grass from banks of channel and removal of silt, zoological waste & debris from canal bed, removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared including conveyance charges

15.2.2:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:4:8 leaner mix ( including equivalent design mix)

OD5500/2023-2024:Dismantling of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Unit / Embedded parts etc. of the sameand stacking at a distance of 100 meter including hire of machinery labour etc. complete as directed by thedepartmental officer at the site.(weight of the unserviceable shutters and embedded parts may be calculatedas 60% and unserviceable hoisting units as 80 % )

2.7.2:Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Hard rock (requiring blasting)

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.2.2:Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Fabrication, Painting and erection of Two regulator shutter near Temple and Electrification of hoisting mechanism of all 3 shutters

OD5445/2023-2024:RING BUND Type-I-Putting up ring bund as per approved shape 2.5m bottom width, 1m top width using empty gunny/polythene bags filled with earth placed in 2 rows at 0.6m apart and filled in between with puddle clay to form bund for an average height 2.00m including labour dismantling the bund after completion of the work etc. complete.

OD5446/2023-2024:Bailing out water Using 5HP Pump- Bailing out water with 5HP engine and pump set including conveyance to site and erection,cost of fuel, lubrication oil and other stores, pay of staff etc complete

OD9210/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD9211/2023-2024: Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD5528/2023-2024:Supply of G.I pipes 40 mm dia

OD5448/2023-2024:Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge / Platform and accessories etc. for the same as per approved specifications, drawings and directions of deptl fficer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already suppliedj ji

85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

85.115:Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

OD5450/2023-2024:Supply and fixing of Bush type CS Roller having OD 90mm x ID 45mm x thread width 55mm with Al Bronzel bush and SS shaft Dia 35 x 110L including cost of all materials, labour , incidental and conveyance charges etc. complete.

OD5451/2023-2024:supply the SS bolt and nut including cost of material and conveyance etc complete

OD5521/2023-2024:Supply of the MS Bolts and Nuts

OD5524/2023-2024: Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platform< including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied

Supply of 3HP Electric Motor and Electrification work

OD9136/2023-2024:Supply of one number worm and pinion reduction gear assembly unit transmit output torque not less than 80 Kgm with minimum of 10 threads on worm and having a total reduction ratio of 40:1 including cost of Worm & Pinion with worm shafts, bearings, cover, cooling etc.

OD5574/2023-2024:Supply of one number 3 HP squirrel cage induction motor TEFC working on 415 volt, 3 phase 50Hz AC supply continuous rating with class F insulation confirming to IS 325/1978 with following accessories like base plate, mounting bolt and nut foundation bolt with nut, Coupling, Coupling bolt with nut and coupling guard etc from the original manufacturer, DP Switch, mainswitch, DOL starter etc. 3HP( Hoist duty type) induction motor, 750 rpm F/L foot mounted, Output shaft extends on both sides

85.128:Providing Line shaft ,material : MS rolled/ forged steel

OD5577/2023-2024:Installing the already supplied 3 HP motor and accessories in correct position and providing all the electrical connections, laying of wires etc. complete with cost of all material, labour, conveyance, incidental expenses etc.

OD5576/2023-2024:Supply and installation of Plummer Block with self aligning ball bearing etc. complete with cost of all material, labour, conveyance, hire of tools, incidental expenses etc.

OD9202/2023-2024:Supply of one number 10 inch dia Clutch assembly unit for the power transmission from motor to the reduction gearbox unit for the safe operation and overload protection of the motor and preventing the bending of screw rod and connecting rods by overloading

OD5575/2023-2024: Trial run the gate with its hoisting mechanism etc. including cost of all materials, machinery , labour, all lift and lead, incidental and conveyance charges etc. as per instruction of departmental officers in charge.

P V Moosa Engineering Contractor

Amity Projects & Construction

ANILKUMAR K K

Bidder Name

ANILKUMAR K K

Excellent

Amity Projects & Construction

P V Moosa Engineering Contractor