Proposed Construction of Gumla Collectorate Building with Facilities at Gumla.

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for earthwork in hard soil as per specification and direction of E/l (vide classification of soil item-B)

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation frenches within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75 B brick work in C.M.(1 :6) in superstructure with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 125 mm thick reinforced designation 75 A brick work in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l.

Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:6) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforced designation 100A brickwork fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of material scaffolfing raking out joint to 15mm depth curing taxes and royalty (but excluding the cost of reinforcement ) all complete as per building specification and direction of E/I.

Extra for brick work for each consecutive floor above first floor including watering and scafolding, all complete as per direction of E/l.

Providing Ashlar Stone masonry in C.M. (1:6) in foundation and plinth with chisel dressed stone, cut to required zise and shape and cleane coarse sand of F.M. 2 to 2.5 includimg coat of screening, carriage of material raking out joints to 20 mm depth curing, taxes and royalty all complete as per building specification and direction of E/I

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor,etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:1½:3 (1 cement:1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation levlling & dressing & finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, buttresses, plinth and string etc.

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Weather shade, Chajjas, corbels etc., including edge

Suspended floors, roofs, landings, balconies and access platform with water proff ply 12 mm thick

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proff ply 12 mm thick

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 40 mm thick

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).

Providing Tor steel reinforcement of 10mm. ,12mm & 16mm dia. bars as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.

(a) 10mm TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).

(b) 12mm TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).

(c) 16mm TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).

Providing Tor steel reinforcement of 20mm. 25mm. 28 mm, 32mm dia. bars as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL)

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/l. (where material is not supplied by deptt.)

Supplying, fitting and fixing callapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing 20 guage G.C.I, sheet gate fitted on M.S. Angle frame of size 60x60x6mm. including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l.

Supplying, fitting and fixing M.S. grill gate with M.S. grills made of 20x6mm M.S. flats or 16mm square bars fitted on 25x25x6mm M.S Angle frame including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l. (where steel is not supplied by the deptt.)

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing 12 mm cement plaster (1:3) with clean coarse sand of F.M 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curring, taxes and royalty all complete as per building specification and direction of E/l.

Providing and laying 6mm thick mosaic flooring of approved texture and colour over 25 mm thick P.C.C. (1:2:4) base with 10 mm down stone chips and sand of F.M. 2.5 to 3 rubbed and polished to granolilthic finish with approved quality of carborandum stone, top layer of 6 mm. being laid with 4 mm and down marble chips of approved quality and shade in ratio (1:2) cement and marble dust mixed in ratio of (3:1) by weight of marble chips including casting in approved block, curing, taxes and royalty all complete as per building specification and direction of E/l. (b) With 100% white cement

Providing and laying 6mm thick mosaic in skirting , dado, steps and pillars of approved texture and colour over 12mm thick cement plaster (1:3) base with sand of F.M. 1.5 rubbed and polished to granolithic finish with approved quality of carborandum stone top layer of 6mm being laid with 4mm and down marble chips of approved quality and shade in ratio (1:2) cement and marble dust mixed in ratio (3:1) by weight of marble chips including cost of curing, royalty and taxes all complete as per building specification and direction of E/l. (b) With 100% white cement

Providing and laying 25mm thick white makrana marble stone slab flooring of approved quality over 19mm. thick base of lime mortar (1:1:1) ( Lime putty : surkhi: coarse sand ) laid and jointed with white cement slurry including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (i)300x300mm

Providing and laying 25mm thick white makrana marble tiles in risers of step, skirting and pillars of approved quality over 12mm thick base of cement mortar (1 :3) and jointed with white cement slurry including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Extra for flooring work for each consecutive floor above first floor complete as per direction of E/l

Providing and laying Double charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less then 0.08% and conforming to IS: 15622/ISO 13006 of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement:4 Coarse sand0, jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with wite cement and matching pigments etc, complete Size of tiles 600 x 600 mm.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 25 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/l.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/l.

Providing two coats of synthetic enamel paint over a coat of primer of approved shade and make over new wooden surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l.

Providing french spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed french polish including cleaning the surface after removing dirt, scales, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l.

Providing french spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed french polish including preparing the surface after cleaning, removing dirt, scales, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing rust , dirt, , scales , smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/l. ( Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l.

Water proofing for old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flextble material brush, roller or spray for water proofing coating per manufacturer Specifications with following steps :-(a)surface preparation .-Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing (loose paint / coating, and cement laitance by cleaning with compressed air water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage leakage. On identification of seepage cement grouting to be done with non shrink expanding admixture of Sika India Pvt.L.td.) MYK Schomberg / Dr Fixiti/ Fosroc or equivallent. Providing and reparing of all Corner and joints such as those between the parapet wall and the roof slab etc shall be chamfered with 150Mrn X 150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic pc?' lymer of Sika/ Fosroc/MYK

Schomberg/Dr 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent.,Befor 'Chamfering a prime coat shall be given with the slurry of acrylic polymer Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modified repair mortar-including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.(b)lst Coat :- Apply 1st coat of two component acrylic modified, ready to use, flexible cementitiot.is material on surface saturated dry roof and inside wall of Parapet.Wall upto 600 mm by brush or roller . After 1st coat of application , 45 gsm of Fibre glass cloth to lay when the first layer is still green. 1st coat shOUld be applied @1.50 kg/Sqmt/coat. For the purpose of measurer-11609-1'e entire treated surface will be measured." (c) 2nd Coat :-To apply the 2nd coat of two component acrylic modified read to use, flexible cementtiOus material right angle to the 1st. coat over the glass fibre laid surface: 2nd coat-,should be applied @ 0.7 Sqmt/coat. For the purpose of

measurement the entire treated surface will be measured." After three days of drying the 2nd coat , the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it. Water proofing Brand:- Sika Topseal 109hi / Fosroc Brushbond RFXI Dr. Fixit Pidiffin 2K / MYK Aquafin TG . Product Performance - Chemical Base Part A: Acrylic copolymer, Part B: Specially graded cementitious powder - Density 1.6 kg/I (mixed density) at +27°C Tensile Strength -2 Nimm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Siren th -2 f\l/mm2 concrete failure Accordin' to ISO4624) Slant-Shear Bond Strength -4 Nimm2 (According to FIP 5.15) Elongation at Break -35% Without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370) (d) )Protection of treated surface with PCG :- The treated surface should be covered with 25mm/50mm F'CC of M-20 grade (1.1.5:3). with proper slope (

1:120) towards the rain outlets in alternate panels of 2 mt x 2 mt keeping 6 rnm gap between the panel joint. Integral water proofing admixture conforming to IS 2645 co of 100 ml per bag of of cement to be added in the screed concreie(paid separately.for this items).All corners shall be chamfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface should be packed prorSeqswith ridti:corict'ete and the peripheral mouth to be sealed with,moisture insensitive epoxy putty of. Sika India .Pvt.Ltd. / MYK Schornbefg /Dr Fixit/Fosroc .For the purpose of measurement the entire treated surface will be measured." (e)Groove of PCC surface should be filled with POlysulphide Sealant.(Paid Separately). Be d - Sika India Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc . Warranty for five years.

Covering of treated surface with PCC :-providing 25 mm thick Cement Concrete M20 (1:1:5:3) maintaining slope in alternate 2 mt x 2mt panels With approved quality of stone chips of 20mm to 6 mm size graded and Cleaned sand of F.M.2.5 to 3 including screening, shuttering, and mixing Cement concrete in mixer with admixture of integral water proofing and Placing in position, striking curing, taxes and royalty all complete as per Building specification and direction of E/I. Panels that has been left should Be casted next day. There should be 6 mm gap between panels .brand- Sika _ plastocrate plus, MYK proof WP 10, Fosroc- Conplast X 421 ic Dr Fixit Pidiproof LM+

Providing and mixing liquid integral water proffing compound in conctrete of plaster as manufacturer specification and as per direction of engineer in charge. Brand. Sika plastocrate plus, MYK proff WP 10, Fosroc-Conplast x 4211C, Dr.Fixit, Pidiproff LW+ or Equivalent

Providing and filling of 6 mm thick Groove between 25 mm PCC Panels with Polysuiphide Sealant (Porin.g Grade)as per drawings and technical specificationsi6nd direction of E in Charge. (with 18% GST) B rand Sika Polysulphide, Fosrpc-Thioflex 600 Dr. Fixit Pidiseal PS(42P. MY K Seal PS or Euivalent.

Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) for grading- I Material

Cost of Driling 200mm x 165mm x 125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

Supplying submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 metre submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supplying fitting and fixing Flat flexible submersible cable with, copper conductor PVC insulated and PVC sheathed. 3 core 4 sq.mm

Supply fitting and fixing GI pipe 50 mm Dia (TATA or equivalent make) Medium Quaility as per IS:1239 ( part 01 ) 2004

Supplying Full automatic star selta starter to operate induction motor working on 415v 3phase 50hz with no coil. Over load element , On _OFF push buttom with necessary materials and connection to Supply etc complete starter with original sheel steel encloser as per 3914. F.A.S.D starter

Providing and fixing in position 25 mm thick bituminastic board (shalitex or Equivalent as per IS:1838-1983) in expansion of construction joints in barrage and its allied works as per specification and direction of E/I

Providing and fixing sheet covering over expansion joints with iron screws as per design. Aluminium fluted strips 3.15 mm thick. 200 mm wide

Wall lining butch work upto 10m height with Dholpur stone 40 mm thick rough facing on the exposed surface with stone strips of minimum length 300 mm and required width, including embedding every tenth layer and bottom most layer in masonry or concrete after making necessary chases of size 75x75 mm and by providing layer of 75 mm thick strips i/c 12 mm thick bed of cement mortar 1:3 (1 Cement : 3 coarse sand) i/c ruled pointing in cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment to match the shade of stone complete as per direction of Engineer-in-charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified

using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the

performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 125x75x4 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the

styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 30 mm thick pre laminated PVC door shutters

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive.

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Profile B Fixing with adjustable lugs with split end tail to each jamb

Profile C Fixing with adjustable lugs with split end tail to each jamb

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.1 Hot finished welded type tubes

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

Light shade pigment using white cement

Medium shade pigment using 50% white cement 50% Grey cement

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class teak wood

Providing and fixing M.S. angle 50x50x5 mm to act as nosing with lugs of M.S. flat 10x5 mm, 10 cm long, forked at end 60cm apart (minimum three lugs to be provided), including necessary welding and applying a priming coat of approved primer on exposed surface etc. complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Single tee with door 110x110x110 mm

Bend 87.5° 110 mm bend

Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37

x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 178 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gm

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 15 mm nominal bore, weighing not less than 32 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc

15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

150 mm dia. R.C.C. pipe

300 mm dia. R.C.C. Pipe

450 mm dia. R.C.C. pipe

Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion

For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality

and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain

glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for

fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or any other accreditation body which operates in accordance with ISO/ IEC 17011 and accredits labs as per ISO/IEC 17025 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml.

3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.

(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/ m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- inCharge

Providing and fixing Sink Cock with Swinging casted spout

Carriage of materials from source to site work including loading & unloading all complete job as per specification and direction of E/I

Aggregate

Stone Metal

Brick

Fly Ash Brick

Boulder

Earth

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, piano type switch, phenolic laminated sheet with suitable size of PVC/MS box etc as required.

Group-A

Group-B

Wiring for Light point/fan point/exaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch , Modular plate, suitable G.I boxes etc as required. Group-C

Wiring for light/power plug with 2x4 sqmm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 No. 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing etc as required.

Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2 x 1.5 sq.mm + 1 x 1.5 sq. mm earth wire

2 x 2.5 sq.mm + 1 x 2.5 sq. mm earth wire

2 x 4.0 sq.mm + 1 x 4.0 sq. mm earth wire

2 x 6.0 sq.mm + 1 x 6.0 sq. mm earth wire

4 x 6.0 sq.mm + 2 x 6.0 sq. mm earth wire

4 x 10 sq.mm + 2 x 6 sq. mm earth wire

Supplying and drawing following pair 0.5 sq.mm FR PVC insulated copper conductor unarmored telephone cable in the existing surface / recessed steel / PVC condute as required. 2 pair

Supplying and drawing co-axial cable RG-6 grade 0.7 mm solid copper conductor, PE insulated, shielded with fine tinned copper draid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required.

Supplying and fixing of following sizes of PVC Conduit along with accesseories in surface/recess including cutting the wall and making good the same in core recessed conduit etc. as required.

Supplying and fixinf=g of following sizes of PVC/G.I box on surface / recess with suitable sizes of phenoil laminated sheet cover in front including painting etc. As required.

75mm x 75mm x 50mm deep / (4" x 4")

72mm x 146mm x 48mm deep / (4" x 7")

Supplying and fixing following piano type switch / socket on the existing switch box / cover including connections etc as required.

5/6 AMPS, one way switch

3 pin 5/6 Amps, socket outlet

TV antenna socket outlet

Electronic step fan regulator, mini

Supplying and fixing following modular Switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required.

5/6 amps, one way switch

5/6 amps, 3 pin socket outlet

Telephone Socket Outlet

Supplying and fixing stepped type fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on existing modular plate & switch box excluding modular plate etc. as required.

Supplying and fixing following size / modules, GI box along with moduler base and cover plate for moduler switches in recess etc as required. 1 or 2 module (78mm x 78mm x 45mm)

Supply and Fixing GI/ PVC box of 75mm x 75mm x 50mm deep on surface or in recess with phenolic laminated sheet cover in front including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.

Supply and Fixing GI box of 121mm x 173mm x 48mm / (6" x 8") (normal size) on surface or in recess with phenolic laminated sheet cover in front including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps piano type switch, connection, painting etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or recess including providing and fixing 3 pin 5/6 amps moduler socket outlet and 5/6 amps modular switch. connection, painting etc as required.

Supplying and fixing suitable size GI box with modular plate & cover in front on surface or in recess including providing and fixing 6 pin 15/16 amps moduler socket outlet and 15/16 amp modular switch. connection, painting etc as required.

Supplying and fixing 2 pin,5 amp ceiling rose on existing junction box/wooden block including connection etc as required.

Supplying and fixing batten/angle holder including connection etc. as required.

Supplying and fixing electronic musical call bell single phase, 230 volt, complete as required.

Installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc, directly on ceiling / wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper conductor.

Installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. including supplying and fixing ball and socket arrangement , 2 nos down rods of 20mm dia x 1.6 mm thick steel conduit upto 30cm length. painting and wiring the down and connection with 1.5 sq. mm PVC insulated, copper conductor, single core cable and eartning etc. as required

Providing and fixing extra conduit down rod of 20 mm dia x 10cm length wiring with 2 x 1.5 sq. mm. FR PVC insulated,copper conductor. single core cable including painting etc, as required. (Note then 5 cm length shall be rounded to the nearest 10 cm and 5 cm of less shall be ignored)

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FR PVC insulated,copper conductor, single core cable etc, as required.

Numbering of Fan/ fittings: Numbering of ceiling fan/ exhaust fan/ fluorescent fitting as required.

Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc as required.

Providing and Fixing following DP / TP&N sheet metal switch disconnector fuse unit in existing metal board with rewireable type fuses, includin drilling holes in metal board, making connections etc as required. 32A, TP&N

Providing and fixing following rating and breaking capacity MCCB with thermomagnetic release and terminal speaders in existing cubicle panel board including drilling holes in cubicle panel, making connection etc. as required.

25-100 amps, 16 KA, fixed thermal setting

125 amps, 16 KA, fixed thermal setting

150/160 amps, 35 KA, fixed thermal setting

200 amps, 35 KA, fixed thermal setting

400 amps, 35 KA adjustable thermal setting

630 amps, 35 KA adjustable thermal setting

S/F Busbar chamber :- Providing and fixing the follwing capacity busbar chamber with 4 strips of length 300 mm made of copper suitable for following capacity complete with all accessories including connections, earthing the body etc. as required. 100 amps

Supplying and fixing the follwing capacity busbar chamber with 4 strips of length 300 mm made of copper suitable for following capacity complete with all accessories including connections, earthing the body etc. as required. 100 amps

Supplying and fixing the follwing way horizontal type three pole and neutral sheet steel, MCB Distribution board, 415 volts on surface/ recess, completed with tinned copper busbar, neutral bus bar, earth bus bar, din bar, interconnections, powder painted including earthing as required. (but wiithout MCB/RCCB/Isolator) 8 way Double door

4 way(4+12) Double door, Horizontal type

6 way(4+18) Double door Horizontal type

Supply and Fixing of following ways surface / recess mounting vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer) as required. 4 ways (8+12), Double door, Vertical Type

Supplying and fixing 6 amps to 32 amps rating, 240 volts, 'C' curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

6/32 amps, Single pole

6/32 amps, DP

40 amps, DP

50/63 amps, DP

6/32 amps, TPN

40 amps, TPN

50/63 amps, TPN

Supplying and fixing of following double pole,240 volts, isolator in existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of 20 amps, 240 volts, SPN insustrial type, socket outlet, with 2 poles and earth, metal enclosed plug top along with 20 amps 'C' curve, SP, MCB, in sheet steel enclosure, on surface or in recess with chained metal cover for socket out let and complete with connections, testing and commissioning etc as required.

Porviding and fixing of M.V. danger notice plate of 200mm x 150 mm, made of mild steel at least 2mm thick and vitreous enamelled white on both sides and with inscription in single red colour on front side as required.

Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal or cock and salt complete etc. as required. (with charcoal or coke and salt)

Providing and fixing 250mm x 5 mm G.I. Strip in 40 mm dia G.I. Pipe from earth electrode including connection with G.I. Nut, bolt, spring, washer, excavation and re-filling etc. As required.

Supplying and laying of 6 SWG G.I. wire at 0.5mm metre below ground level for conductor earth electrode including soldering welding etc. as required.

Supplying and laying 25mm x 5mm GI earth strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with G.I. Nut, bolt, spring, washer, etc as required (Jointing shall be done by overlaping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm)

Providing and fixing 25mm x 5 mm G.I. Strip on surface or in recess for connection etc. as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 35 sq mm direct in ground including excavation, sand cushioning, protective covering and re filling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size exceeding 35 sq mm but not exceeding 95 sq mm direct in ground including excavation, sand cushioning, protective covering and re filling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size exceeding 185 sq mm but not exceeding 400 sq mm direct in ground including excavation, sand cushioning, protective covering and re filling the trench etc as required.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size exceeding 185 sq mm but not exceeding 400 sq. Mm direct in ground in the same trench in one tire horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number PILCA/PVC insulated and PVC sheathed / XLPE power cable of grade exceeding 1.1 KV but not exceeding 11 KV of size not exceeding 120 sq mm direct in ground including excavation and cushioning, protective covering and refilling the trench

Erection of RCC/PCC pole of following length in brick ballast and ramming the foundation, finishing with 150 mm thick cement concrete (1:3:6) layer on top with including excavation and refilling etc as required. Above 6.5 metre and upto 8.0 metre

Erection of metallic pole of following length in cement concrere 1:3:6 (1 cement : 3 Coarse sand : 6 graded stone agregate 40 mm nominal size) foundation including excavation and refilling etc. As required. Above 8.0 metre up to 11.0 metre.

S.I.T.C. Of following rating LED Street lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 Protection) in existing pole / pipe for supply voltage 100-270V AC, 50 Hz. Luminarie shall be confirm to ID 10322 part-5/ section - 3 and shall be complete with all neccssary accessories as required. 45/48 W LED Street light

S.I.T.C. Of following rating LED Flood lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in Existing Pole / Pipe for Supply voltage 100-270V AC, 50 Hz. Luminarie shell be confirm to IS:10322 part-5 / section -5 and shall be complete with all neccssary accessories as required.

75/80W LED Flood light

120 W LED Flood light

Supply, Installation, testing and commissioning of following size ceiling fan 3 blades confirming to IS 374:2019 including wiring the down rods of standard length (upto m cm) with 1.5 Sq. Mm FR PVC insulated, copper wire suitable for 230 V 50 Hz, Single phase supplt etc. complete as required.

1400 mm (56") Ceiling Fan

1200 mm (48") BLDC 5 star rating 32W Ceiling Fan

Supplying installation testing and commissioning following ration surface mounted LED tube light fittings suitable for 230V 50Hz. Single phase supply etc. complete as required. 20/22 W LED Tube Light

S.I.T.C. Of following rating reccess/surface mounted led round / squre shape down light luminaries with pressure die cast housing for single phase supply voltage. Luminaries shall be confirm to IS : 10322 part-5 / section -2 or IEC ; 62722 with all neccssary accessories as required

15/16W LED Round Down Light

18/20W LED Round Down Light

2' x 2' LED Panel Light

S.I.T.C. Of following rating LED Post top lamp made in die cast aluminium housing with decorative clear / opal acrylic diffuser on existing pipe including connection with 1.5 sq mm copper conductor etc all complete as required.40/45W LED Post top lamp clear.

S.I.T.C. Of following rating approved make LED Bollard fitting with rectangular shape of height 600 to 850 mm power input 8/9 watt with die cast aluminum housing opel with PC diffuser, IP:65/54 protection, conferming to IS : 10322 part 5 etc all complete as required.

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) With "P" trap (a)10.0 lit. low level PVC cistern

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) 580 mm long (c) with 10.0 lit. low level P.V.C. cistern

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of "Hindustan" " Parry" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l. Flat back or standing corner (600mmx x350mm)

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l.

Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l

20 mm Dia weight not less than 400 gms

25 mm Dia weight not less than 500 gms

32 mm Dia weight not less than 700 gms

40 mm Dia weight not less than 1.0 kg

Providing and fixing brass / C.I. Stop cock of approved quality all complete as per specification and direction of E/l . 15 mm dia

Cutting chajja or cornice for laying G.I pipe and restoring the same with R.C.C (1:2:4) brick work in cement mortar (1:4) and cement plaster (1:4) as per specification and direction of E/l.

Making holes in walls for laying G.I pipes and restoring the same after pipe laying as per specification and direction of E/l 250 mm thick wall

Cutting drain width wise above G.L. for laying H.C.I, pipe and restoring brick work in cement mortar (1:4) 12 mm cement plaster in (1:4) with neat cement punning as per specification and direction of E/l.

Making holes in wall for laying H.C.I, pipe and restoring the same after pipe laying as per specification and direction of E/l. 250 mm

Supplying all tools and labours and cutting chajja, cornice, for laying H.C.I, pipes and making good the same as per specification and direction of E/l.

Supplying , Fitting and fixing bathroom fitting of approved make and as per IS specification all complete as per direction of E/I (all rates have been adopted from the basic rate from SOR + 15% for labour and contractors profit)

Pillar cock (long neck)

Bib cock - long thread

Piller Cock (ISI)

4- way diverter for conceled fitting

Glass shelf 22"

Fluse valve complete with 32mm size control cock & flange

32mm dia. PVC waste pipe 750mm long with coupling

15mm C.P nipple with coupling

Steel jali - 100mm dia.

Providing Solvent cement

Pressure adjustable shower with revoving joint

Supplying fitting fixing the following items Complete with all material as per specification and direction of E/I

mirrors of 6 mm thick plate glass bevelled edge mirror including C.P. Brass revolving fittings 3 mm ply wood board C.P. Hinges to fix with mirror (i) 600 mm x 450 mm size.

C.P. brass towel rail 20mmX600mm with bracket container

C.P. brass soap dish container medium quality with screw and hinges etc.

Providing and fixing 15mm dia and 45cm long PVC connection pipe with heavy qulity brass coupling at both ends etc all complete as per specification and direction of engineer in charge

Supplying, materrials and labour for constructing inspection chamber of designation class 75B brick size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Supply of following PVC/XLPE insulated PVC sheathed, heavy duty , armoured electrical cable with aluminium conductor for working voltage upto and including 1.1 kV grade( Confirms to IS :1554, part-1).

6 sq.mm, 2 core

10 sq.mm, 2 core

10 sq.mm, 4 core

25 sq.mm, 3.5 core

35 sq.mm, 3.5 core

70 sq.mm, 3.5 core

95 sq.mm, 3.5 core

300 sq.mm, 3.5 core

400 sq.mm, 3.5 core

Supplying fitting fixing G.I. Pipes (Tata mark) or equivalent as per IS-1239 (Part-01)/2004 ISI Marjed / Medium Quality

40 mm dia

25 mm dia

Excavation and refilling of above mentioned medium class GI pipes

Supply of Exhaust metal Fan: Supply and fitting of 230mm, 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required. Make :- Polar/Bajaj/Crompton Greaves / Havells / Orient/ Philips

Supply of Metal Exhaust Fan 12"(300mm): Supply of 12"(300mm), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required( Make- Polar/Bajaj/ Havells/Crompton)

Supply of Metal Exhaust Fan 15"(380mm)(for Kitchen): Supply of 15"(380mm), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required.Make :- Polar/Bajaj/Crompton Greaves / Havells / Orient/ Philips

Supply of Wallmounted Fan: Supply of 16"(400mm), 230V AC wall/cabin fan including fixing the bracket, making , connection testing, commissioning etc as required( Make- Polar/Bajaj/ Havells/Crompton)

LED Bulb 9W/10W : Supplying and fixing of LED 9W /10W bulb and accessories as required. ( Make -Bajaj / Havells/ Philips)

Bulk head 9/10 LED Fitting: Supply and fixing of 9/10W LED, surface mounted bulk head PVE water proof housing for indoor/ ourdoor.( Make-Havells /Bajaj/Wipro/Philips)

Supply, installation of 7.0m height OctagonalHot -dip glavinized pole with top dia 70mm, bottom dia 130mm & made of 3mm thick sheet, base plate dimension 200x200x12mm(L X B X T) including suitable sizes of foundation bolt all complete as required.( without arm) Make_Bajaj/Havells/Surya/ Philips

Supply, installation 0.5m single arm suitable for 70mm top pole all complete as per engineer in charge.

Supply, installation 0.5m double arm suitable for 70mm top pole all complete as per engineer in charge.

Supplying outdoor type copper wound transformer continuously rate for 3 Ph,50 Hz at full load and temp rise not exceeding 45oC by the thermometer in oil and 50oC by the resistance in winding after continuous run at full load rating, the transformer should have oil immersed winding having vector group DY 11 HT side connected in delta and LT Side connected in Star with neutral brought out connected to provide separate earthing . The transformer shall have power terminal arrangement ,bushing, cable end box on HT side and cable end box on LT side 2 nos channels with stoppers shall be provided and fixed on the provided plinth for mounting the transformer .The transformer should have following standard fittings. The transformer shall be latest manufacturing standard as per amended IS specifications and the load and no load losses shall be limited to the values given below or as per IS 2026 or Norms issued by SEB which ever are lower.Oil conservator with filling hole with cap & plain oil level gause.Silica gel dehydrating breather charged with silica gel.Oil Drain Valve.Oil Filter Valve.Lifting eyes/hooks.Two earthing terminals Diagram and rating plate.Air vent.Explosion vent.100 mm dia thermo meter with thermo meter pocket.Four be directional plain roller. with making plateform all complete as per engineer in charge. 630 KVA

Supplying XLPE/PVC insulated armoured cable 1100 V grade with ISI mark Three core, solid/stranded aluminum conductor with 6 mm thick 25 mm width MS spacer with G.I. Earth wire 6 sq mm complete in an approved manner as per IS 7098. 3 core 70 sq mm

SITC of 3 Phase Online 60 KVA UPS with required nos of 12V SMF 120 AH battery ,Rack & Interconnecting cable UPS to battery (10mtrs) for Connected PCs ;Details of UPS: Technology:Mirco processor based controls, true online, double converson type, should have cold start facility Overall Efficiency :>90% Isolation ; Built in isolation transformer at the output of UPS system Charger: Should have built in charger of minimum 10 Amp VAH required :- Minimum 48960 VAH for 60 KVA Display: Should have LCD Display with event logging facility Should have auto phase reverse sequence operation.Should have SNMP (Simple Network Management protocol) compatability. Upgradeability: Should have upgradable to work as parrallel redundant UPS in load sharing mode Software communication: Should have SNMP compatibilty(Optional) Preffered Make-Vertiv/GUTUR/APC, Detailed Specs of 60 kVA UPS , Environmental Characteristics Operating Temperature ºC 0 to 40 Maximal temp. for 8hr day 40 ºC, Mean temp. for 24 hr, 40°C (derate power by 1.5% per °C between 40°C and 50°C, Mean

Temperature for 24hr-Maximally 35, Relative Humidity- ≤95% at 20°C, Altitude of operation- ≤ 1000m asl, Storage/ transport temperature- -25 to 70 ºC, UPS Mechanical Characteristics, Height-1615 mm, Width-715mm, Depth-810 mm, Weight-670 kg, Ventilation-By internal intake fans, Airflow-1280m³ /h, Cable entry Bottom side, Rated Mains Voltage-380, 400, or 415, Supply-Three phase without neutral + Earth, Input voltage tolerance- -15, +10%, Frequency-50 or 60 Hz, Input Frequency tolerance-45~65Hz, Rated input power-73.4 kVA, Rated input current-106A, Maximum input power-81.1 Kva, Maximum input current-117A, Duration of progressive power walk-in- 5~300 sec.

SITC of Sealed SMF Batteries 20 nos. 100 AH x 12 V with 36 months replacement guranty as per IS: 1651-1991 , Make-Exide/Luminus/amron

Supply, installation and commissioning of UPS rack suitable for 30-35 UPS battery installation

Supply, fitting, fixing, errection and commissioning along with civil foundation work of 200 KVA D.G. Set, 415 Volts, 3 Ph. Silent Diesel Engine driven generating set as per IS:1460 & IS : 13018 and alternator as per IS:13364 complete with sound proof company make canopy (Acoustic Enclosure suitable for 200 KVA D.G. Set.) with breaker panel (Standard Mannual Control Panel) and civil foundation work as per the norms of 200 KVA Silent D.G. Set with suitable arrangement for Al./Ar./C etc as required. (Make:- Sterling and Wilson Powergen Private Limited with MTU Engine SDGSC - 3 Cotroller / Kirloskar (GREEN) / Jakson Limited / Mitsubishi / Cater Pillar) Supply of acoustic enclosure for 200 kVA CPCB approved Acoustic enclosure with 80 mm MS base plate, 2 mm CRCA sheet, 50 mm thick foam / 100 mm Rock Wool Insulation, 14 surface tank treatment, dully powder coated and painted with Briliant Blue colour with integrate Fuel Tank, services door, louvers (Fresh Air / Radiator), 1020 dia residential type Silencer, approx dimension L x W x H - 4500 mm x 2000 mm x 2350 mm, complete with following accessories :- a) Fuel Tank.b) Batteries and leads. c) Residential Silencers. d) First fill of lube oil. e) AMF Panel. f) AVM Pads.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 2 run of cable

Supplying, installing on wall or suspension on ceiling, testing and commissioning of following capacity Air Insulated Compact Type Bus Trunking for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints, fire barrier at each floor, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required.

400 A Isc = 30kA for 1 second

630 A Isc = 50kA for 1 second

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required

125 A 15kA SC for 1 sec

200 A 25kA SC for 1 sec

Supplying, installing, testing and commissioning of following capacity TPN tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with TPN disconnector FSU and HRC fuses, connections, earthing etc. as required. 63 A TPN

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required

400 A 30kA SC for 1 sec

630 A 50kA SC for 1 sec

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

2 X 6 sq. mm (19mm)

2 X 16 sq. mm (22mm)

3½ X 25 sq. mm (28mm)

3½ X 35 sq. mm (32mm)

3½ X 70 sq. mm (38mm)

3½ X 95 sq. mm (45mm)

3½ X 300 sq. mm (70mm

3½ X 400 sq. mm (82mm)

Supplying and making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 70 sq. mm

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required 100 mm dia

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body& bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads 2850 lpm at 88 m Head

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron bodyand bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house dulyinsulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 2850 lpm at 88 m Head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron bodyand bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 88 m Head

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body& bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads. 900 lpm at 35 m Head

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

100mm dia

150mm dia

200mm dia

Supplying, fixing, testing and commissioning of butterfly valveof PN 1.6 rating with bronze/gunmetal seat dulyISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

80mm dia

100mm dia

150mm dia

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia (wall thickness 6.3 mm)

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 40 m

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Concealed sprinkler

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 1500mm

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

Clearing grass and removal of rubbish

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 m

Rough dressing the trenched ground including breaking clods.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation

Fine dressing of the ground.

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately Holes 90 cm dia, and 90 cm deep

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, edge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide, lawn mover and brush cutter with fuel & other T & P material/ articles shall be provided by the department.) Permanent office accommodation.(1Mali for 1.25Acre)

Anti termite treatment by digging holes 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 liter per hole in two time or more application to get the trees free from termite infection chemicals used Chlorpyriphos 20% EC in the ratio of 1% concentration and as per direction of officer-in-charge.

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge

Providing and Displaying Bamboo Buddha Valley with fresh & healthy 5 to 6 suckers 1.80 m to 2.10m ht umbrella type well developed in 50 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Bismarckia Palm 115 to 180 cm ht., well developed 12 and above good color fresh and healthy leaves in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Cycus cirsnallis well developed with fresh & healthy 35 to 40 lush green leaves in 40 cm Cement Pot as per direction of the officer-in-charge

Providing and Displaying Cycus revoluta in 35 cm challi, specimen , having 30 to 40 with fresh and healthy, leaves having 25cm to 30cm circumfrance of base stem well developed as per direction of the officer-in-charge.

Providing and Displaying Ficus Long Island topiary well developed with fresh & healthy 5 to 6 ball specific size and shape 120 to 150 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Ficus Retusa topiary well developed with fresh & healthy 5 to 6 big ball specific size and shape 180 to 210cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Phoenix roebelenii palm well developed having 20 to 25 fresh & healthy leaves 90 to 105 cm ht. in 30 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Foxtail palm well developed with fresh & healthy foliage of ht. 210 to 240 cm in big 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Topiary of Ficus Nuda well developed with fresh & healthy foliage from Top to Bottom with single piller 75 to 90 cm spread, 195 to 210 cm ht. in 35 cm Cement Tray /Cement Pot as per direction of the officer-in-charge

Providing and Displaying Topiary of Ficus Panda well developed with fresh & healthy foliage with 3 to 4 Ball and 60 to 75 cm spread each Ball, 135 to 150 cm ht., in 35 cm Cement Tray /Cement Pot as per direction of the officer-in-charge

Providing and Displaying Travelers palm well developed with fresh & healthy leaves foliage 210 to 240 cm ht specimen in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cassia javanica of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Grevillea robusta (Silver Oak) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Jacaranda mimosifolia of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Millingtonia hortensis of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Peltophorum species of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Plumeria alba dwarf dwarf of height 90-105 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Schleichera trijuga (Kusum) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tabebuia sp. of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge..

Providing and stacking of Iresine herbstii, of height 20-25 cm. full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge

Providing and stacking of Ophiopogon jaburan ( variegated ),full of variegated leaves in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge

Providing and stacking of Tradescantia, full of leaves in Earthen Pot/Plastic Pot of size 15 cm. as per direction of the officer-in-charge.

Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size of Poly bags & as per direction of the officer-in-charge.

Providing and stacking of Tradescantia zebrina having in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Ficus benjamina (green) of height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Ficus blackii (F.vivion) (bushy) of height 150-165 cm. with 8-10 branches and healthy foliage in earthen pots of size 30 cm as per direction of the officer-in-charge.

Providing and Displaying Ficus Starlight with fresh, healthy and attractive foliage 45 to 60 cm spread 75 to 90 cm ht., specimen bushy ,in 35 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 34 branches in earthen pots of size 20 cm as per direction of the officer-in-charge

Providing and stacking of Hamelia patens of height 60-75 cm. with 6-8 branches in poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara,Mohan,Scarlet Queen, Variegated, Glabra Formosa, Peruviana Odissi, Paratha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Clerodendrum splendens of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Ipomoea purpurea (Morning glory) of height30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Jasmine humile (Yellow) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Quisqualis indicia of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Tecoma grandiflora of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge

Providing and stacking of Vernonia elaegnifolia (curtain creeper) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Slotted cowl (terminal guard) 100 mm dia

100 mm S.C.I. trap with 100 mm inlet and 100 mm outlet

Rubber insertions for 100 mm dia pipe joints

S.C.I. door pieces 100 mm dia

Non- Schedule items

Providing and fixing of 3D Lite panel System of 22mm thick(minimum) with both the outer walls in clear color and middle cells shall have the alternate horizontal walls in co-extruded white or approved colour. Panels shall be fixed on purlins with Z type Stainless steel Fastener using minimum 3 self drilling screws. Panel shall be 600 mm wide manufactured with vertical standing Seams of 15- 20mm height at both sides of the panel(welding or gluing of upstanding seam is not acceptable). Panels shall be secured with snap on connectors to interlock the panels shall have 2-4 tooth locking system to ensure best performance against wind uplift or hurricane. Polycarbonate Panel system shall also include Aluminium profiles in natural mill finish for end closure. Panels should be manufactured in a manufacturing facility with approved quality assurance procedure as per ISO 9001 & ISO 14001. Panel manufacturer shall provide warranty against any manufacturing defects for a period of 10 years( min.) and should have a succe to be used. The above frames should be fixed to the concrete/ masonary walls and floor by means of self expanding screws panel shall be installed as per the approved drawing, specifications and as directed by the engineer-in-charge.

Providing & injecting chemical emulsion for pre- construction Anti termite treatment and creating a chemical barrier under and all around the column pits wall treanched basement excavation top surface of plinth filling junction of wall and floor along the external perimeter of building with apporoved chemical as per IS coad as per specification and direction of E/I

Main LT Panel for LIFT: - Supplying, designing, manufacturing, installation, testing, fitting, fixing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of panel of 16 SWG CRCA Sheet (1.6mm) CRCA sheet steel with dust and vermin proof with reinforcement of suitable size iron channel, fully compartmentalized cubical type, IP-43 wall mounted, totally enclosed suitable for operation on 415V, 50Hz, 3Ph, AC supply and fault level 25 kA . Make-C&S/ Legrand-DPX3/ Schneider-NSX/ Siemens/L&T. Incomer 63A, 25kA FP MCCB -1 no. Outgoings 40A 10kA FP MCB "C' series-2 nos 32A 10kA DP MCB "C' series-2nos Digital Ammetesr (0-600A)-3 phase, class:o.5 . Make :- AUE / Universal / L&T / Esma. Digital Voltmeter (0-500V)-3 phase, class:o.5 . Make :- AUE / Universal / L&T / Esma.

Advanced New Generation ESE (Early Streamer Emission) Air Terminal Lightning Conductor: Supply and Fixing testing testing of and commissioning of ESE technology lightning arrestor of type DMSGI-45 with Level-1 protection of 63m radious. Device is confirming to standard NFC 17 - 102 & UNE 21186. Mounting arrangement : Device shall be mounted at least 5.0meter clear to highest point by support mast of 40mm dia GI pipe duly galvanised with minimum 85 micron zinc coating withfoundation to suit Mast. The above Advanced New Generation ESE (Early Streamer Emission) technology consist of the following: Air Terminal : Providing of early streamer emission air terminal made of pure stainless steel grade A316 double layer(DIN4301). Mast- Providing of extension support mast made of 40mm dia class A GI pipe duly galvanized suit mast for Level-4 protection of 60m radious(as per NFC17-102) Lighting Flash Counter(LFC): Providing fitting and testing of LFC / search counter upto 6 digit display, suitable for 10kA-100kA to be installed on one of the down conductors approximately 5.0m from the ground level. It registers every lightning discharge intercepted by the air terminal as direct lightning protection. Protective Sheath: A 3" dia approximate 3.0m long plastic pipe is fitted at the ground level to prevent accidental shocks to human beings/ animals during lightning discharge.

Tripod Earthing System for ESE Technology Lightning Conductors-3 nos per set. Supply and Fixing of 16mm dia molecularly bonded with copper on mild steel 2.4 m long(3 nos) as vertical copper electroded into three separate earth pits and joined at the top as per crow feet or delta configuration by three nos. clamps and digging, earth cutting and refilling of earth upto 600mm below ground level, chemical compounds called 'terec" is mixed with soil etc. for tripod maintenance free earthing system for ESE technology lightning conductor. The chemical compound for per set is 5kg. CRIC i.e 6 bags. Soil Treatment-Earth enhancing soil treatment compound TEREC + having essential chemical ingredients, such as ionic chemicals, dispersion chemicalhydroscopic chemicals to be provide stable low resistance for earth terminal to make it maintenance free for over 15 years.

Chemical Earthing Supply, erection and commissioning & testing along with earth cutting, digging earth filling for chemical earthing of the building . Soil Treatment-Earth enhancing soil treatment compound TEREC + having essential chemical ingredients, such as ionic chemicals, dispersion chemicalhydroscopic chemicals to be provide stable low resistance for earth terminal to make it maintenance free for over 15 years. Also provision of masonary enclosure 300mmX300mm withCI cover plate having locking arrangement as earth chamber. Specification: Polution free earthcon compound-25kgs Electrode-2 m long, 17mm dia with 250 micron molecularly bonded with copper coated. HDPE earth pit cover ( Detail of earth pit: UPS room-2 nos, lift machine panel-4 nos, Rising mains-4 nos, EPABX machine- 2 nos)

Supply, fitting, fixing, connecting and testing of 24-port 10/100/1000T and 100/1000 SFP combo stackable switch with 4 SFP+ ports and dual power supply, Switching Capacity 280Gbps and Forwarding Rate 214.3Mpps, 2GB DDR SDRAM, 256MB flash memory, Route maps and redistribution (OSPF, BGP, RIP), Supports up to 64K MAC addresses, SDN or similar kind of technolgy should support, Switch should support link reccovery within 50ms for Ring architecture, All switches, AP, FO Module , Access Points aand WLAN Controller should be from the same OEM, Warranty 5 year from Day 1. (Make:- Cisco - WS-C3850-24XS / Allied Telesis -Model No. AT-x930-28GSTX / Juniper - EX4300) The above L3 Managed Data Switch consists of the following:- 1. Power cord India, right angle. 2. Both side Cable connector. 3. 1 year free service pack.Interface- 24 x 10/100/1000T ports and 4 x 100/1000X SFP ports, Switching Capacity/Forwarding Rate :- 280Gbps/214.3 Mpps,Performance:- Up to 16K MAC addresses, 256MB DDR SDRAM,Management:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN,Security:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN, Routing:- IPv4 static routing and RIP. Fail-over:- Switch capable of recovery within 50ms in a ring for application high

availability, IPv6:- Device management over IPv6 networks with SNMPv6, Telnetv6, SSHv6 and Syslogv6, Diagnostic:- Optical Digital Diagnostics Monitoring,Automatic link flap detection and port shutdown,Port and VLAN mirroring (RSPAN), Standard Protocol:- IEEE 802.1Q,IEEE 802.1w,IEEE 802.1s,IEEE 802.1p,IEEE 802.1AB,IEEE 802.1AX,IEEE 802.3ad, Operating Temparature:- 0°C to 50°C., Certification:-EMC: EN55022 class A, FCC class A, VCCI class A, ICES-003 class A Immunity: EN55024, EN61000-3-levels 2 (Harmonics), and 3 (Flicker) Safety-Standards: UL60950-1, CAN/CSA-C22.2 No. 60950-1-03, EN60950-1, EN60825-1, AS/NZS 60950.1,Certification: UL, cUL, TUV, (RoHS) Compliance-EU RoHS compliant,China RoHS compliant, Warranty:- 5 Years.

24 Port Access Switch 24 x 10/100/1000T ports and 4 x 100/1000X SFP ports, L2 Switch , Switching Capacity 56Gbps and Forwarding Rate 41.7Mpps, operating temperature 0°C to 50°C, Switch should support link reccovery within 50ms for Ring architecture, SDN or similar kind of technolgy should support, Warranty 5 year from Day 1 . Make:- Cisco - WS-C9300L-24T-4G/ Allied Telesis - Model AT-x230-28G / Juniper - EX2200-24) The above L2 Managed Data Switch consists of the following:- 1. Power cord India, right angle. 2. Both side Cable connector. 3. 1 year free service pack. Interface- 24 x 10/100/1000T ports and 4 x 100/1000X SFP ports Switching Capacity/Forwarding Rate :- 56Gbps/41.7Mpps, Performance:- Up to 16K MAC addresses, 256MB DDR SDRAM, Management:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN, Routing:- IPv4 static routing and RIP. IPv6:- Device management over IPv6 networks with SNMPv6, Telnetv6, SSHv6 and Syslogv6, Diagnostic:- Optical Digital Diagnostics Monitoring,Automatic link flap detection and port shutdown,Port and VLAN mirroring (RSPAN), Operating Temparature:- 0°C to 50°C, Certification:- EN,UL and RoHS, Warranty:- 5 Years.

24 Port POE Access Switch Supply, fitting, fixing, connecting and testing of switch with 24 x 10/100/1000T PoE ports and 4 x 100/1000X SFP ports, PoE+ L2 Switch , Switching Capacity 56Gbps and Forwarding Rate 41.7Mpps, Switch should support PoE and PoE+ with 370W minimum power budget, operaating temperature 0°C to 50°C, Switch should support link reccovery within 50ms for Ring architecture, SDN or similar kind of technolgy should support, Warranty 5 year from Day 1 . Make:- Cisco - WS-C9300L-24P-4G / Allied Telesis -AT-x230-28GP / Juniper - EX2200-24P) The above L2 Managed Data Switch consists of the following:- 1. Power cord India, right angle. 2. Both side Cable connector. 3. 1 year free service pack. Interface- 24 x 10/100/1000T ports and 4 x 100/1000X SFP ports, Switching Capacity/Forwarding Rate :- 56Gbps/41.7Mpps, Performance:- Up to 16K MAC addresses, 256MB DDR SDRAM, Management:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN, Security:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN, Routing:- IPv4 static routing and RIP. Fail-over:- Switch capable of recovery within 50ms in a ring for application high availability, IPv6:- Device management over IPv6 networks with SNMPv6, Telnetv6, SSHv6 and Syslogv6 Diagnostic:- Optical Digital Diagnostics Monitoring,Automatic link flap detection and port shutdown,Port and VLAN mirroring (RSPAN) Standard Protocol:- IEEE 802.1Q,IEEE 802.1w,IEEE 802.1s,IEEE 802.1p,IEEE 802.1AB,IEEE 802.1AX,IEEE 802.3ad, Operating Temparature:- 0°C to 50°C, Certification:- EN,UL and RoHS, Warranty:- 5 Years.

10/100/1000 MM SFP Module SITC of Gigabit Fiber Module-MM, Support up to 550mtr (Make:- Cisco - GLC-SX-MMD / Allied Telesis -Model No. GLC-SX-MMD/AT-SPSX/CTP-SFP-1GE-SX) / Juniper - CTP-SFP-1GE-SX), OEM must provide declaration on conformity of all the passive components to the following standards: a) TIA/EIA 568-2.D ; b) TIA/EIA 568-3.D ; c) ISO/IEC 11801, OEM must be a member in the TIA and BICSI organization. OEM shall have RCDD certified manpower in India for design support and validation. Certificate is Mandatory, OEM should have valid ISO 9001 and ISO 14001 certificate on Design, development and manufacture of SW and HW solutions for communication networks.

12 Port LIU Switch : SITC of 12 Port Loaded LIU with SC Unit for 6 MM fiber Multi mode fibres OM3 (2 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 12 Fiber Capacity & 12 Nos. of SC Pigtail - Pigtail 1 Meter MM OM3 (Make:Legrand/Panduit/RIT/Siemon) Detailed Specs for Fiber Optic LIU Rack Mount LIU (12/24 Ports) Should have Slide type drawer structure , Height: 1 U, 1.75 inches (12 & 24 Ports), Material: Cold Rolled Steel in surface coated by electrostatic epoxy powder, Slots: FMS should have sufficient slots to accommodate adaptor plates, Empty Slots of FMS should be covered with blank plates., Splice Tray : Splice Tray of ABS, Comply with UL 94V2 material should be supplied with LIU., The adaptor plate should be pre-loaded with LC/SC Type Multi mode Duplex Adaptors., Port Density :12/16 LC/SC Single mode Ports All LC adapters should be duplex type with shutter for protection. Adapters should be snap mount for easy insertion and removal. Insertion Loss: <0.2 to <0.1 dB, Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2, Operating Temperature: -40°C to +75°C, Connector Insertion Loss: 0.30dB(Max), Attenuation: 1310/1550 : 0.36/0.22 dB/KM

24 Port LIU : SITC of 24 Port Loaded LIU with SC Unit for 24 MM fiber Multi mode fibres OM3 (4 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 24 Fiber Capacity & 24 Nos. of SC Pigtail - Pigtail 1 Meter Multi Mode OM3 (Make:Legrand/Panduit/RIT/Siemon) Detailed Specs for Fiber Optic LIU Rack Mount LIU (12/24 Ports) Should have Slide type drawer structure , Height: 1 U, 1.75 inches (12 & 24 Ports), Material: Cold Rolled Steel in surface coated by electrostatic epoxy powder, Slots: FMS should have sufficient slots to accommodate adaptor plates, Empty Slots of FMS should be covered with blank plates., Splice Tray : Splice Tray of ABS, Comply with UL 94V2 material should be supplied with LIU., The adaptor plate should be pre-loaded with LC/SC Type Multi mode Duplex Adaptors., Port Density :12/16 LC/SC Single mode Ports All LC adapters should be duplex type with shutter for protection. Adapters should be snap mount for easy insertion and removal. Insertion Loss: <0.2 to <0.1 dB, Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2, Operating Temperature: -40°C to +75°C, Connector Insertion Loss: 0.30dB(Max), Attenuation: 1310/1550 : 0.36/0.22 dB/KM

Fiber Patch Cord SITC of Fiber Duplex Patch Cords SC-LC MM-OM3 Patch Cord 2 mtr. (Make:Legrand/Panduit/RIT/Siemon) Cable : LC/SC-SC/LC 50/125μm MM OM3 Multimode Duplex Patch Cord Length : 3mtrs, Connectors : The optical fiber patch leads shall comprise of Multi mode 50/125μm fiber with 2XLC type fiber connectors terminated at one end of fiber patch cord and 2xSC type connector at other end of the fiber patch cord, Insertion loss should be better than ≤ 0.30 dB, Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2, Attenuation: 50/1300 : 3.0/1.0 dB/KM, Connector Loss : 0.30dB(max), Operating Temperature : -40°C to +75°C

6-Core MM Armoured Fibre Optics Cable, SITC of 6-Core OM3 MM Armoured Fibre Optics Cable in Mtrs: (Make:Legrand/Panduit/RIT/Siemon), The fiber should be optimized for operation at 850 nm and at 1300 nm. Should fulfill the requirements of ISO.IEC 11801 - 2nd Edition, type MM OM3, ITU-T REC G 651D spec IEC 60794-1-2 F5, No of Cores : 6/12, Max. Attenuation: At 850 nm <= 3.0 dB/km, At 1300 nm <=1.0 dB/km, Modal Bandwidth: At 850 nm: ≥1500 MHz.km, At 1300 nm: ≥500 MHz.km, Fibre/Tube Identification : Single Tube, Fibre protection (Tubes) : Polybutylene Terephthalate (PBT), Armouring : CST, Outer Sheath : HDPE >2.0 mm, Pheripheral Strength Member: CST, Cable Diameter (D) : 8.8 ± 0.3 mm, Mass (Nominal) : 82 kg/km, Min. Bending Radius (during Installation) : 20 D;D-Outer Diameter, Max. Tensile Strength-Short Term : 1500N, Max. Crush Resistance-Short Term : 2200N, Operating Temperature range : -40°C to +70°C.

Patch Panel-24 Port Fully Loaded SITC of 24 port UTP jack panel (24 port RJ-45 Loaded CAT-6 UTP 19" rackmountable patch panel preferbaly with 6 blocks). (Make:Legrand/Panduit/RIT/Siemon) Patch panel should be modular design, populates up to 24 UTP keystone-type jacks in 1U, Patch panel should be Enhanced with cable strain relief with retention tray; It should be single metal both front panel and rear tray, Information Outlet or connectin module should comply with the specification mentioned above in 2, Standard : Conforms to IEC-60603-7 (603-7) for keystone-type, snap-on apertures, Should be RoHS complied

Straight LAN Patch Chord-2 Mtr SITC of Straight LAN Patch Chord-3 Mtr (Make:Legrand/Panduit/RIT/Siemon) Standardization: Compliant with Cat.6, Class E requirements: ISO/IEC 11801 2nd Edition Compliant with Cat.6 component standards IEC 60603-7-4 and 60603-7-5 , Cable shield: U/UTP, Number of conductors : 8, Stranding: 7 x 0.20 mm (24 AWG), Cable jacket characteristics: cable, metal-free, Cable overall diameter: 6.5±0.2 mm, Tube / Wire type: stranded conductor, Insulation: solid polyolefin, 0.97±0.02 mm diameter, Plug: Feature cable retension, with enhanced pull strength., Cat 6 patch cord plug to have round cable holder and strain relief boot to avoid bending., Jacket: PVC with 8 different color options, Plug should have high repeatability cross talk performance

Straight LAN Patch Chord-1 Mtr SITC of Straight LAN Patch Chord-1 Mtr (Make:Legrand/Panduit/RIT/Siemon) Standardization: Compliant with Cat.6, Class E requirements: ISO/IEC 11801 2nd Edition Compliant with Cat.6 component standards IEC 60603-7-4 and 60603-7-5 , Cable shield: U/UTP, Number of conductors : 8, Stranding: 7 x 0.20 mm (24 AWG), Cable jacket characteristics: cable, metal-free, Cable overall diameter: 6.5±0.2 mm, Tube / Wire type: stranded conductor, Insulation: solid polyolefin, 0.97±0.02 mm diameter, Plug: Feature cable retension, with enhanced pull strength., Cat 6 patch cord plug to have round cable holder and strain relief boot to avoid bending., Jacket: PVC with 8 different color options, Plug should have high repeatability cross talk performance

SITC of white modular plate type Single front plate for 1 Nos. RJ 45 Data outlet (Make:Legrand/Panduit/RIT/Siemon), Should be UK style Keystone-type Faceplates are available in 1, 2 & 4 port configurations, Should be featured with shutter options, the screws not to be visible, Should support Work with both Flush and Wall mount box, Should support Operating Temperature: -10～+60; Storage Temperature: -40～+68; Humidity: 10%~90% RH, Material: ABS, UL 94V-0; Spring: SUS304; Surface Finish: Polished,

SITC of RJ 45 Data Module to be fixed on face plate (Make:Legrand/Panduit/RIT/Siemon) RJ45 Jack of Category 6, for the establishing of transmission channels of class E with up to 4 plugged connections, complies with Category 6 requirements of the standards ISO/IEC 11801:2nd edition, EN 50173-1, DIN EN 50173-1: 2002 as well as ANSI/TIA/EIA 568-B.2-1, de-embedded tested in acc. with IEC 60603-7 (603-7), interoperable and backwards compatible with Cat.5e and Cat.5., Suitable for 10GBase-T applications in acc. with IEEE 802.3an up to 500 MHz and 55 m. Compatible with RJ standard plugs (RJ11, RJ12, RJ45), PCB- and tool based connection of installation cables AWG 24 – 22 (0.5 mm – 0.65 mm) and flexible cables AWG 26/7 – AWG 22/7. IDC termination should feature nil crossover in acc. with EIA/TIA 568-A/B, gold-plated bronze contacts for >750 mating cycles, >200 insertion cycle, Material: RoHS complied, Housing material: Polycarbonate (UL-94-V0), Should be available with or without dust protection feature, Should be 3P certified.

Splicing of Armoured SM/MM Fibre Optics Cable: Splicing, testing and commissioning of supplied, OFC cable of 6-Core Armoured Fibre Optics

SITC of Fully Loaded 15 U 19" 600*600 Wall Mounted Rack with all required accessories -2 Nos. of Fan,6A 6 Plug PDU-1 Nos. ,Cable Manager-2 Nos., Mounting Screws-20 Pcs ; Preffered Make-Legrand/APW/President/Valrack

Providing, fixing, fitting, installation and testing of 42 U Network Rack as server cabinet 19" LCS2 along with all standard accessories, 800mm (W), 1000mm (D), approx. Wt.150 Kg, CRCA 'D' grade 1.6mm thick sheet, pwoder coated for cabinet , 4mm Toughened Tinted Glass Door and along with following accessories:- 1. Cooling fan 220/230V AC, of 90 CFM-- 4 Nos. , 2. Cable manager Metal 4 Nos. 3. PDU- 230V /AC 1 No., le Channel 100mm wide. 2 Nos. 5. Heavy Duty Stationary Shelf 600mm(W)X475mm(D) - 1 No. , 6. Mounting Hardware (20 Sets of M-6 screws, washers, cage, nuts (Nickle Coated)- 3 Nos. ,7. Earthing strips copper 150mm H 1 No. 8. Door Lock 1 No. ,9. Caster Wheels (with breake) 2 Nos. 10. Caster Wheels (without breake) 2 Nos. ,11. Front Metal Band 1 No. (Make : Legrand /Schneider/Ortronics),(To be installed in centrelly located Server Room); Preferred Make-Valrack/President/Rittal

SITC of EPABX SYSTEM: IP based 100% non-blocking EPABX System should be a IP Compatible with rich feature set of the system and can be connected with pure Voice over IP (VoIP) communication network across corporate Local and Wide Area Networks (LAN and WAN) as & when required. Central Processing Unit: The system main software should be open architecture based. The CPU of main system shall be 32 bit processor working at 2.0 GHz or better. The system should be rack mountable. • System Architecture should be latest pure IP and should be wall Mountable  Meet-me conference 30 party X 2 from day 1 must be available. Must Support Unified Communications Equipped with 368 Analog Extensions expandable upto 384 Extensions,16 Analog Trunk Ports, 1 PRI with 1 IP Phone to be Used as Opertor Console with 6DSS Keys, 02 Ports Auto Attendant,EPABX Make: Avaya/NEC/Unify

Analog Basic CLI Push Button Telephone: SITC of analog telephone- Make: Panasonic/ BPL/Beetel

SITC of Telephone Tag Block): IP-65( weather proof). Preffered Make-Krone.

50 pair krone Box fully loaded without IPM

400 Pair krone Box fully loaded without IPM

600 Pair krone Box fully loaded without IPM

SITC of multi-core telephone jelly filled armoured PVC cables of conductor size 0.5 sq.mm annealed tinned electrolite grade copper , PVC insulated twisted pairs bunch togeather over all PVC sheathed , Laid on tray or along the wall or laid in pipes or in trenches including excavation of cable trench, sand filling covering with bricks and back filling complete as required. Make: Polycab/ Finolex/ Deltron/Havells/Anchor, 50 Pair

SITC of white modular plate type Single front plate for 1 Nos. RJ 45 Data outlet (Make:Legrand/Panduit/RIT/Siemon)

Digital Conference System Wireless Access Point along with all hardware and soft ware with all required equipments and components complete set. Make:- BOSCH DCNM-WAP/ Harman/BOSE The ‘Wireless Access Point’ (WAP) shall be used as a standalone central control device for wireless connection and control of the Wireless Devices. , The WAP shall have the following features: • Easy to use, • Truly wireless, no need for an additional WiFi router for tablet control. • Easy and intuitive web interface for system setup, configuration, control and licensing. • Native support for camera control. Zero Interference, • Seamless automatic wireless frequency channel switching; up to 44 channels in the 2.4/5 GHz band. • Packet Loss Concealment to mask the effects of lost or discarded packets.Standard WiFi, For giving a clear visual overview of the proceedings. • A maximum of six HD Conference Dome cameras can be connected to the system with native support. General Web interface, • The WAP shall support the following software functions, which shall be available through the web interface (Some functions shall be not supported when a tablet device is used). Configuration, • User management shall give the possibility to create several users with user specific access to functionality. • 5 band parametric equalizer.• Camera control and HD-SDI switcher configuration. • Wireless network SSID and WPA2 settings. • Wired network host name setting (DHCP and zero config protocol based on Bonjour,

STIC 5 Battery Packs for Digital Conference System Wireless Contribution Uni . Make:- BOSCH-DCNM-WCH05//Harman/BOSE

Providing of Corded Digital Deligates Units Gooseneck microphone with programmable switch . With Specifications such as: Frequency response:200 Hz to 12.5 kHz. -Headphones load impedance:> 32 ohms < 1k ohm, -Loudspeaker nominal output:72 dB SPL, - Length of microphone :480 mm (18.9 in), - Plug and play functionality for ensuring fast installation and reconfiguration times , Immunity to mobile phone interference and with Features such as: Possible-to-speak indication, Request‑to‑speak indication, Built-in loudspeaker with volume control, Built‑in 3.5 mm (0.14 in) stereo headphones socket, Built‑in volume control for headphones, Color-coded LED indicator above microphone button, for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak, Immunity to mobile phone interference Make & Model is: Bosch- CCSD-DL./Harman/BOSE

Providing of Corded Digital Deligates Units Gooseneck microphone with programmable switch With Specifications such as: Frequency response:200 Hz to 12.5 kHz. -Headphones load impedance:> 32 ohms < 1k ohm, -Loudspeaker nominal output:72 dB SPL, - Length of microphone :480 mm (18.9 in), - Plug and play functionality for ensuring fast installation and reconfiguration times Immunity to mobile phone interference and with Features such as: Possible-to-speak indication, Request‑to‑speak indication, Built-in loudspeaker with volume control, Built‑in 3.5 mm (0.14 in) stereo headphones socket, Built‑in volume control for headphones, Color-coded LED indicator above microphone button, for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak, Chaiman Button Make & Model is :Bosch- CCSD-DL./ Harman/BOSE

Providing of Digital central conference controller with Built‑in MP3 recorder with internal memory and USB recording, Built‑in Digital Acoustic Feedback Suppression, Quick and easy connection upto 80 discussion devices, Native support for automatic HD camera control, Signal to noice :> 94 dBA, Frequency response for input :30 Hz to 20 kHz, Recording/ Playback (bit rate):64, 96, 128, 256 Kbit/sec, Nominal loudspeaker output:72 dB SPL and Functions such as: Plug-and-play functionality, Web browser control, Open microphone control, Built-in MP3 recorder, Discussion control Make & Model is: Bosch-CCSD-CURD/ Harman/BOSE

SITC of Mixer 10 channel Analog Mixer suitable for the prescribed solution Make-Souncraft/AKG/Yamaha/Bosch/BOSE ;

SITC of wall mounted cabinet speaker 30 Watt includes mounting system Dual 4" 2‑Way Surface-Mount Loudspeaker,Compact full range,Ideal for Conference Halls, patios, and retail,Vented LF enclosure,1-inch titanium diaphragm HF driver with neodymium magnetic structure,Coherent Coverage Waveguide,Full-bandwidth overload protection (LF and HF),Elliptical weather-resistant ABS enclosure,Paintable black or white finish,Magnetically shielded for video applications,Strong-Arm Mount™ for easy, flexible aiming,"T" version for 70 or 100 V distributed systems with specifications of Frequency Range (-10 dB)- 65 Hz – 20 kHz, Sensitivity (SPL, 1 W/1 m)- 89 dB,Max. SPL/1m (calc.)- 115 dB,Power Handling (Continuous, Peak)- 100 W, 400 W,Transformer taps(transformer version only)- 70 V: 3.75 W,70 V/100 V: 7.5, 15, 30 W, Coverage, H x V- 120° x 80°, LF Transducer-Two 4", HF Transducer -1", Nominal impedance-(non-transformer version)- 8 Ω, Dimensions (H x W at front x D) -12.2" x 6.9" x 8.5",(310 x 175 x 216 mm) ; Make- AKG/BOSE/EV

SITC ofHandheld Wireless Mic with Cardiod polar pattern for transmitter,Dynamic microphone with Neodymium magnet , Receiver frequency response 80Hz-18kHz,Receiver RF sensitivity < 1.0 µV,Receiver Image rejection>55dB,Receiver Dyanmic range >95dB and receiver having 32 channels possible,Receiver S/N ratio >100dB A,distortion <1 %, Transmitter sensitivity - 3.2 mV/Pa,modulation:+/-40kHz (Approved Makes: Audio Technica, Senheiser, Electro-Voice)

SITC of Headworn Wireless Mic with Cardiod polar pattern for transmitter,Dynamic microphone with Neodymium magnet , Receiver frequency response 80Hz-18kHz,Receiver RF sensitivity < 1.0 µV,Receiver Image rejection>55dB,Receiver Dyanmic range >95dB and receiver having 32 channels possible,Receiver S/N ratio >100dB A,distortion <1 %, Transmitter sensitivity - 3.2 mV/Pa,modulation:+/-40kHz (Approved Makes: Audio Technica, Senheiser, Electro-Voice)

SITC of required cables & Accessories for Conference Halls

6u Network Equipment Rack 600X 600 with power socket, amplifier support, exhaust fan, etc.Prefrred Make- Valrack/Rittal/President

SITC Speaker Cable 2 core 2.5 Sqmm PVC coated and PVC sheathed multistrand copper flexible unarmored FRLS cable; Make-KRYSTAL/Polycab

Mic Cable-Supply of 0.75 Sq. mm 2 Core Shielded Microphone Cable (100 m Roll); Approved make- Krystal

SITC of Wooden Podium alongwith Cable Cubby (One HDMI Cable, Two LAN Cable, Two unswitched AC outlet,One 3.5 mm Mini Stereo Audio Jack,Compact size with square bezel Black color of make-Kramer/Crestron/Lightware/Magnum; Wooden Podium would be manufactured locally

SITC of Cable Cubby (One HDMI Cable, Two LAN Cable, Two unswitched AC outlet,One 3.5 mm Mini Stereo Audio Jack,Compact size with square bezel Black color of make-Kramer/Crestron/Lightware/Magnum;

SITC of HDMI Cable-2 Mtr;Make- Krammer/Wyrestorm

SITC of Projection screen :- high gain ,Best quality Motorized ProjectionScreen with Remote ,133",16:9 with viewing area of 65” x 116”; Make: Liberty/Da-Lite/Draper

SITC of Projection screen :- high gain ,Best quality Motorized ProjectionScreen with Remote ,110",16:9 with viewing area of 54” x 96”; Make: Liberty/Da-Lite/Draper

SITC of Ceiling mounting Kit For Projector; Preferred Make- Liberty/Raymax

Projector: 4,300 lumens WXGA high brightness compact projector Display System: 3 LCD system Size of effective display area: 0.75”(19mm) x 3 BrightEra LCD Panel Aspect ratio 16:10,Number of pixels : 3,072,000 (1280x800 x 3) pixels Throw Ratio :1.10:1 to 1.79:1,Zoom – Ratio : Approx. x 1.6,Contrast ratio (full white / full black) 20000:1 *2,Speaker: Speaker 16 W (monaural) INPUT A : RGB / Y PB PR input connector: Mini D-sub 15 pin female Audio input connector: Stereo mini jack INPUT B: RGB input connector: Mini Dsub 15 pin female Audio input connector: Stereo mini jack INPUT C: HDMI input connector: HDMI 19-pin, HDCP support Audio input connector: HDMI audio support INPUT D: HDMI input connector: HDMI 19-pin, HDCP support Audio input connector: HDMI audio support,S VIDEO IN : S Video input connector: Mini DIN 4-pin VIDEO IN: Video input connector: Phono jack,OUTPUT : MONITOR output connector: Mini D-sub 15 pin female Audio input connector: Stereo mini jack LAN : RJ-45, 10BASE-T/100BASE-TX,USB: Type-A & Type-B MICROPHONE IN: Microphone jack: Mini Jack,Display resolution: Maximum display resolution: 1600 x 1200 dots, fV:60Hz,Screen size : 30" to 300" (0.76 m to 7.62 m) (measured diagonally); Preffered Make-Panasonic/Hitachi/Sony

SITC of HDMI bidirectional RS232 and IR over high definition base1 , Transmitter Make-Kramer/Crestron/ Key digital

SITC of HDMI bidirectional RS232 and IR over high definition base1, Receiver Make-Kramer/Crestron/ Key digital

4MP IR Bullet Fixed Camera -1/2.8"Progressive Scan CMOS, 2688 × 1520 at 25fps, 2.8 mm Fixed lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering, UL, CE, FCC certified.Preferred Make- Axis/Pelco/Hikvision

4MP IR Indoor Dome/Bullet Fixed Camera -1/3" Progressive Scan CMOS, 2688 × 1520 at 25fps, 2.8mm Fixed lens, 0.01 Lux at F1.2, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, IK10, Alarm & Audio: 1 input & 1 output, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Audio exception detection, video tampering, UL, CE, FCC certified.Preferred Make- Axis/Pelco/Hikvision

IP Fixed Mini Dome Camera: 1/2.7" Progressive Scan CMOS, ICR, 0.01 lux at F1.2, 0 lux with IR, 1920x1080:25fps, 2.8mm Fixed Lens, H.265, MJPEG, Three individually configurable stream, IK08, IP66, DC12V & PoE, 120dB WDR, 3D DNR, BLC, Support on-board storage up to 128GB (SD card not included), Alarm -1 input,1 output, IR range: up to 10m, Edge Anlalytics- Line crossing detection, intrusion detection, Motion detection,face detection, video tampering, UL, CE, FCC certified. Preferred Make- Axis/Pelco/Hikvision

SITC of 4MP 35× Network IR PTZ Camera with Dual-sensor, 1/1.8" progressive scan CMOS,Full-color image output,Up to 2688 × 1512 resolution,Min. illumination:Color: 0.0005 Lux @(F1.5, AGC ON),B/W: 0.0001 Lux @(F1.5, AGC ON),0 Lux with IR, 35× optical zoom, 16× digital zoom, 120 dB WDR, 3D DNR, HLC, BLC, EIS, Chromatic Defog, Support H.265+/H.265 video compression, Support rapid focus, Deep-learning-based target classification algorithm for auto-tracking 2.0 and perimeter protection, Up to 250 m IR distance. Smart IR, Rain-sensing auto wiper, IP67,White Balance-Auto/Manual/ATW (Auto-tracking White Balance ) /Indoor/ Outdoor/Fluorescent Lamp/Sodium Lamp,Lens 5.9mm to 206.5 mm, 35× Optical, Zoom Speed-Approx. 4.4 s (optical lens, wide-tele),Field of View-Horizontal field of view: 58.9° to 2.2° (wide-tele),Vertical field of view: 35.3° to 1.2° (wide-tele),Diagonal field of view: 65.9° to 2.5°(wide-tele),Working Distance-10 mm to 1500 mm (wide-tele),Aperture Range-F1.6 to F4.4, Movement Range (Pan) 360° endless, Perimeter Protection-Intrusion, Line Crossing, Region Entrance, Region Exiting, Support alarm triggering by specified target types (human and vehicle),Filtering out mistaken alarm caused by target types such as leaf, light, animal, and flag, etc.,Event Detection--Unattended Baggage Detection, Object Removal Detection, Face Detection, Audio Exception Detection,Motion Detection, Video Tempering Alarm, Exception (HDD Full, HDD Error, Illegal Login, IP Address Conflict, Network Disconnected),Smart Tracking-Manual Tracking, Auto Tracking (support tracking specified target types such as human and vehicle), Event Tracking,Smart Record,ANR (Automatic Network Replenishment), Dual-VCA, ROI Main stream, sub-stream and third stream respectively support eight fixed areas.Protection Level-IP67 Standard. Lightning protection, surge protection and voltage transient protection meets IEC61000-4-2-2/3/4/5/6 Preferred Make- Axis/Pelco/Hikvision

SITC of 128 ch Smart Network Video Recorder: Connect Up to 128 IP Cameras, Dual OS, Should support N+1, Hot spare, Up to 12 Megapixels Resolution, Two independent HDMI and one VGA Output, HDMI outputs of 4K resolution, VGA outputs upto 1080, Support H.265, H.264, MJPEG, Incoming Bandwidth 750 Mbps, Support RAID0, RAID1, RAID5, RAID 6, and RAID10, ANR Technology, 24 SATA interfaces for 24 HDDs and capacity of each HDD upto 8TB, 3x USB with two USB 3.0, Alarm I/O 16/8, RS-485, 4 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, UL certified.Preferred Make- Axis/Pelco/Hikvision

SITC of 6TB Surveillance Grade Hard Disk for NVR for 30 Days Back up; Make-Seagate/WD

Surveillance class Common Micro SD Card 128GB for camera; Make Hikvision/Axis/Pelco

SITC 75" 4k LED Panel,Preffered Make-LG/Samsung

Providing and fixing PVC Pipe fittings with all accessories (Supreme, Prince, Astral or Equivalent )

i) 110 mm Door Tee (Supreme, Prince, Astral or Equivalent ) P.V.C.

ii) 110 mm Plain Bend (Supreme, Prince, Astral or Equivalent ) P.V.C.

iii) 110 mm Door Bend (Supreme, Prince, Astral or Equivalent )P.V.C.

iv) 110 mm 45 degree offset (Supreme, Prince, Astral or Equivalent ) P.V.C.

v) 110 mm Cowel (Supreme, Prince, Astral or Equivalent ) P.V.C.

vi) 110 mm Plain Trap (Supreme, Prince, Astral or Equivalent ) P.V.C.

i) 75 mm Door Tee (Supreme, Prince, Astral or Equivalent ) P.V.C.

ii) 75 mm Plain Bend (Supreme, Prince, Astral or Equivalent ) P.V.C.

iii) 75 mm Door Bend (Supreme, Prince, Astral or Equivalent )P.V.C.

iv) 75mm 45 degree offset (Supreme, Prince, Astral or Equivalent ) P.V.C.

vi) 75 mm Plain Trap (Supreme, Prince, Astral or Equivalent ) P.V.C.

Providing and fixing ball valve (full brass, KEC / APAR/ ZOLLOTO make or equivalent ) all complete . 32 MM DIA NOMINAL BORE

Providing and fixing Sprinkeler for Irrigation (full brass, KEC / APAR/ ZOLLOTO make or equivalent ) all complete . 32 MM DIA NOMINAL BORE

Providing and fixing PTMT flange 15mm size 56mm dia suitable for 15mm taps and weighing not less than 5gms of apporved ISS make

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42. For Terrace Pump

Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required

3 x 50 sq.mm.(aluminium)

3 × 10 sq.mm.(aluminium)

10 2.5 sq.mm.(Copper)

2 × 1.5 sq.mm. in Conduit

Supplying fitting fixing Pressure Gauge Assemble with Gate/Ball Valve all complete as per engineer in charge.

Supplying fitting fixing Air release Valve / Drain Valve all complete as per engineer in charge.

Supplying fitting fixing MS Structure support for piping all complete as per engineer in charge.

Providing and fixing 25 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

Providing and laying 19mm dia PVC conduit complete with required junction boxes in recessed / surface system PVC insulated copper conductor cable of 2x1.5 sq.mm. in existing conduit as required. Make:Polycab/Mescab

Supplying installation testing commissioning 8 PASSENGER LIFT/ 544 Kgs / 4 Floors / 4 Stops / STAINLESS STEEL (1.5 mm) Car Cabin Lift as per specidication-Load / Speed-8 Persons (544Kgs.) / 1.25 Mtr. Per Second, Drive-MICRO PROCESSOR BASED VVVF - CLOSED LOOP, Travel / PIT / HEADROOM-12 METER / PIT 1600mm / HEADROOM 4200 mm, Number Of Floors-4 (G+3), Floor Display Char-0,1,2,3, Number Of Landing Entrances-4 (G+3), Number and Position of Car Entrances-1 (ONE), IN FRONT ONLY, Position Of Machinery-DIRECTLY ABOVE THE LIFT WELL -GEARLESS, Size of Lift Well-1850 X 1700 (MM Wide * MM Depth * MM Height * MM E-Value), Lift Car Inside Size-1300 X 1100 X 2200 (MM Wide * MM Depth * MM Height * MM C-Value), Clear opening of Gates / Doors / Lintel / Ec-800 X 2000 (MM Wide * MM Height) Lintel - 2200 mm ., Type or Design of Lift Car-STAINLESS STEEL (1.5 mm) - HONEYCOMB , Car Ceiling - Car Floor-SLEEK (SMALL CIRCULAR LIGHTS) - SS HONEYCOMB -PERGO, Car Fittings-LED LIGHTS & CROSS FLOW - FAN, Type Of Car Front Entrance Protection-POWER OPERATED CENTRE OPENING SLIDING DOOR - STAINLESS STEEL

Landing Operation Safe Landing Operation, False Ceiling In Car, Infra Red Door Screen, Overload Warning Indicator, 3 Way Intercom / Press And Speak Phone, Free Service For One Year, Pit Ladder Ss Handrail, Stainless Steel Braille Button With S.S. Cover Machined Tee Guide For Car & Cwt, Cast Iron Filler For Cwt

Main LT Panel for Collectorate Building :- Supplying, designing, manufacturing, installation, testing and commissioning of LT Panel of 14 SWG CRCA sheet (2 mm) steel , dust and vermin proof with reinforcement of suitable size iron channel size - 100 mm x 100 mm x 6 mm with proper lifting arrangement effecting proper connection of all incomer and outgoing(IP-43) fully compartmentalized cubical type, floor mounted , totally enclosed, extendable on both sides, switch board and suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 50 kA with front operated construction including separate fabrication arrangement for fixing A.C.B. and Bus Coupler. The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for multi runs aluminum cables for all ACB, Bus coupler, M.C.C.B. The panel includes 415V, 1600A, 3Ph, 50kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium Earth Bus with removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 4, 6, 10 & 16 Sq mm PVC Cu. wire. All incomer ACB and bus coupler shall be mechanically operated drawout type and with microprocessor communicable release. All 4 pole MCCB with thermomagnetic based release must have following character: Icu=100% Ics with adjustable S/C and

O/L, Provision for inbuilt earth leakage module & provision for inbuilt measuring unit., Incomer:, 1000A FP / ACB with handle (50kA) Outgoings:, 630A FP/ 36kA-2nos( 1 for normal rising main and 1 no for DG), 400A FP/ 36kA-2 nos( 1 for APFC panel and 1 for Essential rising main), 630A TPN change over open execution and panel mounted type with front rotary handle., 200A FP/ 25kA, MCCB-3 nos.( 1 no. for fire pump, 1 no for UPS room SDB and 1 no spare), 100A FP/ 25kA, MCCB-3 nos.( 1 no. for outdoor feeder pillar and 2 nos. spare), 63A FP/ 16kA, MCCB-6 nos.( 2 nos. for lift machine panel, 1 no for pump house & 2 nos. spare), 3 nos -Digital voltmeter (0-500V) , 3 phase, class0.5. Make :- AUE / Universal / L&T / Esma. 3 nos-Digital Ammetesr (0-500A) 3 phase, class 0.5 . Make :- AUE / Universal / L&T / Esma., 3 nos CT 1250/5VA -5 class one Epoxy resin cast CT 1 Set. Make :- Kappa / Matrix / SG Electricals / EPICAST., 9 nos LED indicatore (RYB) of 220V. 1 Set of 3 nos Make :- ESSEN / L&T - ESBEE / Binay / Teknik, 9 nos Fuse base with HRC Fuse Set of 3 nos. Make :- Legrand / L&T / Schinder. , Aluminium Bus Bar for Panel- Al E91EWP bus bar size( 50mmx 6mm )x 5 for each phase and (50mm x 4mm)x5 for neutral and 60mmx 10 mm for Al. bus earth, 1600A, 415V, 3Ph , 4W, 50kA, 50Hz, shall be heat shrinkable PVC sleeved(R Y B & N) after temperture & enclosure de-rating max. allowable temprture of bus bar shall be 90 oC. etc as required.

A.P.F.C. Panel (Capacitor Bank) Auto Mannual Type (APFC) Panel – 200 kVAR 14 Stage Capacitor Bank Details with mixed dielectric Ultra Heavy Duty Capacitors of following range :- Supplying, designing, manufacturing, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of A.P.F.C. Panel (Capacitor Bank / Auto Mannual) of 14 SWG CRCA sheet (2 mm) steel IP – 54 floor mounting cubical type Capacitor Bank Panel suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 50kA with approximate size – 2,600 mm (H) x 2,700 mm (L) x 800 mm (W) with front operated construction including separate fabrication arrangement for fixing A.C.B., M.C.B., Capacitors, Contactors etc. The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized with locking arrangement duly fixed on Base Channel with proper lifting arrangement size – 100 mm x 50 mm x 6 mm having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs and Capacitors having earthing arrangement. All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for multi runs aluminum cables for A.C.B., and MCB. The panel includes 415V, 800A, 3Ph, 50KA Electrolytic Aluminium Bus Bar (E91EWP) size 2 Nos. 120 mm x 8 mm for per Phase, 1 No. 120 mm x 6 mm for Neutral with removable glands plates, cable glands at sending and receiving ends, including connection with Contactors and MCBs complete in all respects. All inter connections shall be made with 2.5, 4, 6, 10 & 16 Sq mm PVC Cu. wire. The panel shall have type test certificates with short circuit and IP protection (C.P.R.I. Test) Location : E

Supply, erection and commissioning & testing along with earth cutting, digging earth filling for chemical earthing of the building . Soil Treatment-Earth enhancing soil treatment compound TEREC + having essential chemical ingredients, such as ionic chemicals, dispersion chemicalhydroscopic chemicals to be provide stable low resistance for earth terminal to make it maintenance free for over 15 years. Also provision of masonary enclosure 300mmX300mm withCI cover plate having locking arrangement as earth chamber. Specification: Polution free earthcon compound-25kgs Electrode-2m long, 17mm dia with 250 micron molecularly bonded with copper coated. HDPE earth pit cover, ( Detail of earth pit: Transformer-4 nos( 2 for neutral+ 2nos for body), DG-4 nos, LT panel- 2nos, Outdoor F/P- 2 nos and pump house-2 nos)

Supply and laying of 1000 mm x 600 mm x 12 mm thick chequered Rubber Matting of tested quality to with stand 15kV dielectric strenght as per IS:5424 complete in all respects.

Supply of 11 KV grade Rubber Hands Gloves. As per IS:4770.

Supply of First Aid Box with all necessary materials and medicine as approved by Indian Red Cross / St. Jhon's conforming to IS:2217.

Supply and fixing of Shock Treatment Chart with glass in Aluminium frame and to be fixed on wall in Bengali, Hindi and English.

Supply and fixing of 11 KV / 415V Danger Board as required.

Fire Extinguisher : Supply and fixing of carbon dioxide(Co2) type fire extinguisher of 4.5 kg as per IS: 2828

Providing fitting,fabrication of MS angle of section 50mmX50mmX6mm size for 40 m PCC trench to make support of MS iron plate to be fixed on every after 300mm in PCC trench.For Electrical room

Providing fitting,fabrication of MS plate of 12mm thick for covering PCC cable trench on the support of iron angle each piece of MS plate shall be 600X800mm. For Electrical room

Stainless Steel Text (Text Height 250 mm ) Text COLLECTORATE BUILDING Gumla at Pergola Slab with Grouting all Complete Including matrial & Labour as pet E/I

Supplying, fitting and fixing jet type fountain with mechanical plumbing and electrical system to achieve height of 8 feet to 10 feet of the jet including brass nozzle inlet outlet PVC Connecting Pipe & Fitting with mortar and balancing tank all relevant fittings for smooth and equal functioning as per drawing with labour and material, taxes all complete as per direction of engineer in charge.

Providing and Displaying Hyphorbe Lagenecaulis 115 to 180 cm ht., well developed 12 and above good color fresh and healthy leaves in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Nolina recurvata well developed with fresh & healthy 35 to 40 lush green leaves in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Ficus Benjaminatopiary well developed with fresh & healthy 5 to 6 ball specific size and shape 120 to 150 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Lawsomnia inerme(of height 60-75 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge.

Providing and dispalying seasonal/ Annuals flowers in full bloom well developed fresh and healthy plant in 25-30 cm Earthen pot/ Plastic Pot and as per direction of the officer - in - charge

Add 12 % GST

Add 1% Labour Cess

RAJBIR CONSTRUCTION PVT. LTD.

Dipanshu DIPANSHU PROMOTER AND BUILDER PVT. LTD.