Design ,supply, Installation and commissioning of Laboratory Furniture at new campus Yerpedu

Amount

LAB FURNITURE :MODULAR LAB FURNITURE WITH C FRAMES Design ,supply, Installation and commissioning of best quality factory made ready built Knock down type modular steel laboratory furniture with working height 900mm high as per attached drawings, all surfaces shall be zinc phosphated/degreased and epoxy powder coated with 60 to 80 microns thickness confirming to ASTM/ IS Codes, complete as per standard specifications given in the tender document. . Laboratory furniture shall consists of under structure "C " frame and under bench suspended with sliding arrangement, sink units with internal plumbing, Laboratory bench designed for carrying a loading of 300 kg/sqm, including reagent shelves, wall rails, storage cabinets etc. consisting of the following For C Frame, Back/end/side panels,Table top,Skirting,Under bench suspended base steel cabinets,Reagent shelves ,Sink and Accessories ,Acrylic Anti Splash Guard ,Switch & sockets for more details please refer tender document

Island table 6.7m x 1.8m x 0.9m with 8 nos of underbench storage cabinet of width 900mm, with one drawer and double leaf shutter with one shelf, reagent rack of two stages, Switch and sockets

Island table 6.7m x 1.8m x 0.9m (8 underbench storage cabinet of width 900mm, with one drawer of 900mm width, double leaf shutter with one shelf,sink to one end with swivel tap, shutter for the sink face and bottom sheet under the table, reagent shelves of five stages)

Island table 6.7m x 1.8m x 0.9m (8 underbench storage cabinet of width 900mm, with one drawer of 900mm width and double leaf shutter with one shelf, reagent shelves of five stages)

Island table 3.7m x 1.8m x 0.9m (4 underbench storage cabinet of width 900mm, with one drawer of 900mm width and double leaf shutter with one shelf, reagent shelves of five stages)

Island table 6.7m x 1.8m x 0.9m (8 underbench storage cabinet of width 900mm, with two drawer of 450mm width, double leaf shutter with one shelf, two sinks in the centre with swivel taps, shutter for the sink face and bottom sheet under the table, reagent shelves of 3 stages)

Island table 3.7m x 1.5m x 0.9m (8 underbench storage cabinet of width 900mm, with one drawer of 900mm width and double leaf shutter with one shelf)

Island table 6.3m x 0.9m x 0.9m (no underbench storage cabinet)

Wall table 8.4m x 0.9m x 0.9m (4 underbench storage cabinet of clear width of 2.1m with shutter leaves of min 750mm )

Wall table 6m x 0.9m x 0.9m (4 underbench storage cabinet of clear width of 2m with shutter leaves of min 750mm)

Wall table 0.9m x 0.9m x 0.9m (With one sink, swivel tap, shutter for the sink face and bottom sheet under the table, switch & sockets not required)

Wall table 7.2m x 0.9m x 0.9m (4 underbench storage cabinet of width 900mm, with one drawer of 900mm and double leaf shutter with one shelf)

Wall table 5.6m x 0.9m x 0.9m (3 underbench storage cabinet of width 900mm, with one drawer of 900mm and double leaf shutter with one shelf)

Wall table 4m x 0.9m x 0.9m (2 underbench storage cabinet of width 900mm, with one drawer of 900mm and double leaf shutter with one shelf)

Wall table 3m x 0.9m x 0.9m (1 underbench storage cabinet of width 750mm, with one drawer of 750mm and double leaf shutter with one shelf)

Wall table 1.2m x 0.9m x 0.9m (1 underbench storage cabinet of width 600mm, single leaf shutter and one shelf, one sink, swivel tap and shutter for the sink face and bottom sheet under the table, switch & sockets not required)

Wall table 5.6m x 0.9m x 0.9m (2 underbench storage cabinet of width 900mm, with one drawer of 900mm and double leaf shutter with one shelf, one sink, swivel tap and shutter for the sink face and bottom sheet under the table)

Wall table 3.2m x 0.9m x 0.9m (2 underbench storage cabinet of width 750mm, with one drawer of 750mm and and single leaf shutter with one shelf)

Wall table 2.4m x 0.75m x 0.9m ((2 underbench storage cabinet of width 750mm, with one drawer of 750mm and and single leaf shutter with one shelf)

Wall table 7m x 0.9m x 0.9m (3 underbench storage cabinet of width 600mm, single leaf shutter and one shelf, one sink, swivel tap and shutter for the sink face and bottom sheet under the table)

Wall table 6.7m x 0.9m x 0.9m (3 underbench storage cabinet of width 750mm, single leaf shutter and one shelf, two sink, swivel taps and shutter for the sink face and bottom sheet under the table)

Wall table 3m x 0.9m x 0.9m (4 underbench storage cabinet of width 750mm, with one drawer of 750mm and and single leaf shutter with one shelf)

Wall table 3.3m x 0.9m x 0.9m (2 underbench storage cabinet of width 900mm, with one drawer of 900mm and and single leaf shutter with one shelf, 2 underbench storage cabinet of width 750mm, with one drawer of 750mm and and single leaf shutter with one shelf)

Wall table 10.2m x 0.9m x 0.9m (no underbench storage cabinet)

Wall table 6.3m x 0.9m 0.9m (no underbench storage cabinet)

Wall table 1.2m x 0.9m x 0.9m (With one sink, swivel tap, shutter for the sink face and bottom sheet under the table, switch sockets not required)

Storage cabinets made of 1.2mm thick CRCA steel with chemical resistance epoxy powder coating ( 60 to 80 micron thickness matt finish) of approved colour, having double wall construction for side walls, smooth exterior and interior surfaces, cabinet sides with spar edges in the front to accommodate door hinges, sides to have holes to accommodate shelving supports or side, back wrap around body with corner posts with holes to support shelf supports. A steel plinth should be integrated into the carcass with four screw feet for height adjustments (-5/+15 mm). Plinth height 900 mm. Shelving: Shelves shall be constructed from CRCA steel panels (1.0 mm thickness) with all around 27mm strengthening edge; load capacity of 90 kg., height should be adjustable to optimise storage inside the cabinet. Doors should be constructed with double skin construction with sound damping technology, 270° openable 3 axis adjustable hinge or SS304 knuckle hinges with separate door catches for both doors with integrated SS D handle- 160mm high, diameter 10mm.

Size- 900w x 560d x 2150h with 5 shelves

Size- 900w x 560d x 2150h with 5 shelves (Shutters to have 5mm thk toughened glass of four panels each of size 300w x 750 mm)

Safety shower and Twin cup Eye wash - Emergency shower systems with twin cup eye showers, designed and engineered to secure easy operation. This allows for “one-action” activation of the shower system ensuring immediate and continued flushing without any need for further action. This easy operation also allows the injured person to use both hands to keep his eyes open for effective flushing, to undress under the shower or just to help exposing the affected area for better and more expedient treatment. On the eye shower the nozzles are protected by rubber cups to keep the injured person from hurting himself unintentionally. The nozzles are also protected against dust and dirt by the caps which are removed automatically by the initial jet of water. All eye showers & safety showers are delivered with water regulating devices ensuring 11.5 lit/min for eye wash and 75 lit/min for shower, constant adequate water flow regardless of high water pressure and to be fitted with backflow preventer. Make :- Broen / Water saver.

Overhead framed glass sliding door cabinets - wall storage units made of CRCA steel with chemical resistance epoxy powder coating (60 to 80 micron thickness matt finish) of approved colour and should be 1.2mm thick, double wall construction for side walls with sound dampening technology or side and back wrap around body with corner posts with holes to support shelf supports, shelves shall be provided, constructed from 1.0mm thick CRCA steel epoxy powder coated with all around 27mm strengthening edge, load capacity of 90 kg/ shelf , height should be adjustable to optimise the storage space in side the cabinet. Framed glass sliding door leaf shall be constructed from 1.2mm thick CRCA/ galvanized steel panels, bent to 20mm thickness all around, dampened with contact cushions with 5mm thk toughened glass at with polished edges fixed to shutter frame with pvc gasket. A guide runner shall be provided at the bottom with plastic coated ball bearings or the shutter should be top hung, supported on a ball bearing nylon roller running in a track attached to the top of the cabinet with a guide rail at the bottom. All cabinets should have load carrying capacity of 90 kg per cabinet. All cabinets should have a magnetic label to show details about it’s content. All storage cabinets should be provided with interchangeable cylinder locks.

Size: 900w X400d X 750h with 2 adjustable shelves

Ducted Storage cabinets made of 1.2mm thick CRCA steel with chemical resistance epoxy powder coating 60 to 80 micron thickness matt finish of approved colour, having double wall construction for side walls, smooth exterior and interior surfaces, cabinet sides with spar edges in the front to accommodate door hinges, sides to have holes to accommodate shelving supports or side, back wrap around body with corner posts with holes to support shelf supports. A steel plinth should be integrated into the carcass with four screw feet for height adjustments (-5/+15 mm). Plinth height 100 mm. Shelving: Shelves shall be constructed from CRCA steel panels (1.0 mm thickness) with all around 27mm strengthening edge; load capacity of 90 kg., height should be adjustable to optimise storage inside the cabinet. Doors should be constructed with double skin construction with sound damping technology, 270° openable 3 axis adjustable hinge or SS304 knuckle hinges with separate door catches for both doors with integrated SS D handle- 160mm high, diameter 10mm. Reagent cabinet should be provided with vent at the top to connect exhaust duct alomg with following accessories. a) Centrifugal (PP + FRP) lined blower designed to confirm to fumehood standards of SEFA and ASHRAE including cost of all neccesary accessories such as starters etc. complete. b) Dry scrubber system. c) PP-FRP ducting of wall thickness 3mm PPGL + 3mm FRP for sizes up to 500mm Dia, including PP Damper, FRP lining shall be of fire resistant isothelic resin fume hood underbench connections and necessary MS supports (Enamel paint with primer applied) for ducts.

Size- 900w x 560d x 2150h with 5 shelves (Near Fume hood)

Size- 900w x 560d x 2150h with 5 shelves (Near Fume hood)

Size- 900w x 560d x 2150h with 5 shelves

Design, Supply & installation of bench top low constant volume fumehood with underbench storage cabinets of 600mm in height connected to a single centrifugal blower, scrubber with suitable ducting and other accessories/appliances/units detailed below and as per detailed specification annexed to this BOQ. a) The C-frame shall be not less than 60mm x 30mm and should be not less than 2mm thick. b) The cover panels shall be of GI epoxy powder coated(minimum 60 micron) not less than 1.2mm thick. c) The work top shall be of 18mm thick jet black granite with PP sink of size oval shaped 102mm x 175mm ‘PP’ Cup-sink for drainage. d) Lattice rod assemblies 12mm dia solid epoxy coated rods shall be clamped with the PP clamps to form a lattice arrangement should be minimum 200mm horizontally and vertically e) The fumehood consist of air flow monitor, distribution board with rocker switch, LED light (set of two), 3 module plate with socket and tiny trip (set of two), raw water, compressed air, nitrogen flexible tubing service valves f) There shall be 3 underbench storage cabinet for flammable solvent, for storing apparatus and the last one to store acids. The storage cabinets shall have double leaf shutters. g) Centrifugal (PP + FRP) lined blower designed to confirm to fumehood standards of SEFA and ASHRAE including cost of all neccesary accessories such as starters etc. complete. h) Dry scrubber system. i) PP-FRP ducting of wall thickness 3mm PPGL + 3mm FRP for sizes up to 500mm Dia, including PP Damper, FRP lining shall be of fire resistant isothelic resin fume hood underbench connections and necessary MS supports (Enamel paint with primer applied) for ducts. j)Utility services piping in fume hoods (for Nitrogen, argon, Compressed air & water), consisting SS 304 pipes of required dia and length, all pipes extended up to 150mm above the Fume hood top including making connections with control valves etc complete internal piping work. Approval to be obtained for shop drawing with scheme before manufacturing.

1800(L)x900(D)x1350(H) (Acid storage cabinet, Solvent storage cabinet & Metal powder coated cabinet)

1800(L)x900(D)x1350(H) (Acid storage cabinet, Solvent storage cabinet & Metal powder coated cabinet)

1200(L)x900(D)x1350(H) (Acid storage cabinet & Solvent storage cabinet)

1200(L)x900(D)x1350(H) (Acid storage cabinet & Solvent storage cabinet)

Instalaltion and Commising Charges,if any

Any Other Charges if Any

Godrej and Boyce Mfg Co Ltd