REPAIR AND REPLACEMENT OF INTERNAL WIRING AND CONNECTED ACCESSORIES AND EXTERNAL CONNECTION WORKS AND MISC E/M WORK AT 5N DET NAVY AT MIL STN BARRACKPORE UNDER GE BARRACKPORE

Amount

Excavation in trenches for laying under ground cable, foundation and erection of poles and stays in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 meter deep and getting out complete all as specified and directed.

Returning, filling in, including spreading leveling, watering and well ramming in layers not exceeding 25cm soil all as specified and directed.

Removing surplus excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting points as in soft/loose soil all as specified and directed.

M&L for sand cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep including required watering and consolidation after laying and stretching the cable complete all as specified and directed.

M&L for brick covering with width equal to length of brick as protection to cable with well burnt sub class ‘B’ bricks of size 250mm x 125mm x 75mm laid dry flat complete all as specified and directed.

M&L for XLPE insulated, LT armoured electric cable with aluminium standed conductor 1100 volts grade, cross-sectional area 25 Sqmm, 4.0 core laid in trenches/pipes/ducts/wall/boarings with necessary cable lugs and glands, nuts, bolts and washers etc and testing including taking down old unserviceable cable complete all as specified and directed.

M&L for XLPE insulated, LT armoured electric cable with aluminium standed conductor 1100 volts grade, cross-sectional area 10 Sqmm, 4.0 core laid in trenches/pipes/ducts/wall/boarings with necessary cable lugs and glands, nuts, bolts and washers etc and testing including taking down old unserviceable cable complete all as specified and directed.

M&L for XLPE insulated, LT armoured electric cable with aluminium standed conductor 1100 volts grade, cross-sectional area 6 Sqmm, 4.0 core laid in trenches/pipes/ducts/wall/boarings with necessary cable lugs and glands, nuts, bolts and washers etc and testing including taking down old unserviceable cable complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, bell, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, holders, regulators, sockets, light fittings and including making good the disturbed surfaces to match with the existing surfaces by applying white/ colour wash/distemper over applying of putty for smooth finish surface complete all as specified and directed.

M&L for point wiring complete with 1.5 sqmm PVC insulated, FR-LSH type, ISI marked, conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade (MMS) and including cutting, chasing work at any height and all accessories concealed in walls / roofs / floors / ceiling etc. flush mounting MS box with top, bottom, side/back wall knockout for conduit entry from any direction made out of 1.60mm thick and 50mm depth suitable for fixing of modular top cover , blanking plate as per numbers of switch modules, modular switches, sockets, fan regulators, red colour indicator, blank plates etc as approved coloures modular accessories of suitable modules and including 1.5 Sqmm PVC insulated multistranded FR-LSH type unsheathed single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surfaces by applying white/colour wash/distemper as applicable after applying of putty for smooth finish surface complete all as specified and directed for the following:- (Note:- (i) All necessary accessories such as modular metal box, top cover plate with frame, blank plate, screws, washers etc are to be used of same make/brand only in relevant items. (ii) Cutting & chasing of wall for point wiring at any height shall be done and cost of the same deemed to be including with quoted rate.)

One light point controlled by one switch .

One fan point controlled by one switch and one regulator.

One exhaust fan point controlled by one switch .

One 5 pin 6 amps socket point controlled by one 6 amps switch on independent board .

One 5 pin 6 amps socket point controlled by one 6 amps switch on same board .

One bell/buzzer point controlled by one bell push.

One light point controlled by two Nos two way switches .

Ditto- all as per Item No.10.00 here-in-before but point wiring with 2.5sqmm PVC insulated multistranded flexible unsheathed copper conductor FR-LSH and earth conductor of size 2.50 sqmm complete all as specified and directed for the following :-

One 6 pin 6/16 amps socket outlet point controlled by one 16 amps switch on independent board.

One 6 pin 6/16 amps socket outlet point controlled by one 16 amps switch on same board.

Ditto -all as per Item No.10.00 here-in-before but point wiring with 4sqmm PVC insulated multistranded flexible unsheathed copper conductor FR-LSH and earth conductor of size 4 sqmm PVC insulated multistranded flexible copper conductor FR-LSH of 3 pin, 15/16 Amps socket outlet on independent board complete all as specified and directed.

S&F of modular switch 10 Amps, single pole, 1 way, 1 module, 240V, AC complete all as specified and directed.

S&F of modular switch 10 Amps, 2way, single pole,1 module, 240V, AC complete all as specified and directed.

S&F of modular bell push 10 Amps, single pole,1 module, 240V, AC complete all as specified and directed.

S&F of modular switch 16 Amps, single pole, 1 module, 240V, AC complete all as specified and directed.

S&F of modular socket shuttered type 6 Amps, 2/3 pin combined 2 module, 240 V, AC complete all as specified and directed.

S&F of modular socket 6/16 Amps, 6 pin combined shutter socket, 2 module with light indication, 240 V, AC complete all as specified and directed.

S&F of modular red colour lighting indication lamp 6 Amps, single pole, 1 module, 240volts, AC, 50 Hz complete all as specified and directed.

S&F of modular fan regulator, electronic, 360 degree rotation (0 to 4), 100 to 120 Watts, 2 module, 240Volts, AC complete all as specified and directed.

S&F of call bell, AC, 230 Volts single pole, multi music type ISI marked complete all as specified and directed.

S&F of angle lamp holder, insulated body with back plate for batten fittings including 12 Watt LED lamp complete all as specified and directed.

Supply, installation, testing and commissioning of Retro fit emission control device on existing 82.5 KVA DG sets, approved by CPCB accrediated labs for reduction of particulate matter, carbon monoxide and hydrocarbon etc at source by minimum 70 percent without any adverse effect on engine (back pressure should be under permissible limit) including all other necessary items required for fixing and installing the same complete all as specified and directed. Make : Chakra or equivalent as approved.

S&F of ceiling rose , three terminal, PVC/polycarbonate body, ISI marked complete all as specified and directed.

S&F of three phase cable junction box of size 400 x 300 x 190mm water & fire retardent proof out door type of approved , hinged/screwed type made of SMC plastic single door with incoming and outgoing connector/terminals and comprising of MCB SP 6 Amps, 240V, 10KA, 'C' Series and including galvanised flat iron clamps of size 25X5mm thick -02 Nos GI nuts, bolts & washers etc for fixing on PCC/Steel tubular pole/ wall surface etc and including removing of old unserviceable item complete all as specified and directed.

M&L for PVC conduit heavy duty of size 20 mm dia from looping box to Street light connector, holding in MS clamp of size 25X2 mm thick at every one mtr used in each pole 04 Nos of clamps with necessary nut, bolts and washers etc and including PVC sheathed three core multistranded copper conductor cable of size 1.5 sqmm from looping box to light fitting connector and including removing of old unserviceable item complete all as specified and directed.

S&F of decorative box type 20 -22watt LED fittings with and including LED T-8 tube light 20 watt of fire retardant engineering grade complete with all accessories internally pre-wired, connecting up with and including three core sheathed flexible copper conductor cable of required size and including mounted on PVC/Wooden round/square blocks-02 Nos complete all as specified and directed. (Make : Philips Cat No. TMC501T8 and MAS LED tube PC body/ Crompto Greeves Cat No. IGP 118 T8 and LT8-20865-2/ Surya Cat No. SUB 118 T8 & SLETLDS 20 PC or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of 10 watt LED light fitting mirror type with high out put diffuser 2 feet, 220 V AC decorative type with driver holder and LED lamp including connecting up with aluminium housing with PC diffuser three core flexible copper conductor cable of suitable size other fixing accessories complete all as specified and directed. (Make : Havells Cat No. LUMILINE PLUSBS10W LED865SPCSSIND/ Bajaj Cat No. BCLAB10W/ Surya Cat No. SLEBT10IL or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of 1x9W/1x10W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including fixing arrangements at any height with nuts, screws and washers and connected to ceiling rose complete all as specified and directed. (Make: Philips Cat No. WT202WLED6SCWPSUS2PC/SURYA Cat No. SLE BH 10W/Bajaj Cat No. BIBWP10W LED or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of round shape 15 watt , 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size other fixing accessories complete all as specified and directed. (Make : Havells Cat No. EDGEPRONEORDDLR15WLED840S/ Crompton Greeves Cat No. LCDRC15CDL/ Surya Cat No. ATHENA SLEDLR15WXXRD or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of recess mounting 2'x2' LED 34/36 Watt light fittings with LED lamp and required driver, slim in class LED ceiling panel with best in class aesthetic white powder coated frame blended seamlessly with ceiling layout modular ceiling grid and also can be suspended with provided kit and necessary electric connection with and including required size three coat sheathed flexible copper conductor cable from looping box to light fitting and testing including taking down old unserviceable items complete all as specified and directed. (Make: Bajaj Cat No. BCTBLR 36W LED FP CW/Surya Cat No SLEDS3622R TROFFER/ Havells Cat No.PLUTOSURFACE4X1PLS34WLED857S / Philips Cat No. RC 380B LED36S 6500 G4 L60 W60 PSU ODOC or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of powder coated sheet metal enclosure, 415 volts, AC, VTPN DB (V-vertical type distribution board) 8 way plus 24 modules, for flush mounting with 200amps copper busbar, 2 neutral/earth bar for ease of installation and MCCB incomer of rating upto 200Amps, FP and MCB SP /TP MCB's as outgoing and complete connecting cable links with top and bottom with IP43 DBs protection and including making good the disturbed surfaces to match with existing surface and colour coat including taking down old unserviceable DBs complete all as specified and as directed. (Make: Legrand cat No.5077 32, 8 way /L&T Cat No.DBVTH008GD/ C&S Cat No. CSDBTPNVDD08S or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of powder coated sheet metal enclosure 415 volts AC,TPN distribution board 8 way 8+24 modules suitable for flush mounting with 100 Amps copper busbar, neutral bar, earth bar and MCB incomer of rating upto 100 Amps, MCB TPN/DP, and MCB SP as outgoing and complete connecting cable links with top and bottom removable gland plate with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface and colour coat including taking down old unserviceable DBs complete all as specified and as directed. (Make:- Legrand cat No. 5076 82 8 way /L&T Cat No. DBTPN008GD/ C&S Cat No. CSDBTPNHPCGDD08 or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of powder coated sheet metal enclosure 415 volts AC,TPN distribution board 4 way suitable for flush mounting with 100 Amps copper busbar, neutral bar, earth bar and MCB incomer of rating upto 100 Amps, MCB TPN/DP, and MCB SP as outgoing and complete connecting cable links with top and bottom removable gland plate with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface and colour coat including taking down old unserviceable DBs complete all as specified and as directed. (Make:- Legrand cat No. 5076 80 4 way /L&T Cat No. DBTPN004GD/C&S Cat No. CSDBTPNHPCGDD04 or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of powder coated sheet metal enclosure 240 volts AC, SPN distribution board 8 way for flush mounting with 200 Amps copper busbar, neutral bar, earth bar and MCB incomer of rating upto 200Amps, MCB SPN/DP and MCB SP as outgoing and complete connecting cable links with top and bottom removable gland plate with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface & colour coat including taking down old unserviceable DBs complete all as specified and directed. (Make: Legrand Cat No. 5076 21 8 way /L&T Cat No.DBSPN008GD/C&S Cat No. CSDBSPNPCGDD08 or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of powder coated sheet metal enclosure 240 volts AC, SPN distribution board 4 way for flush mounting with 200 Amps copper busbar, neutral bar, earth bar suitable for MCB incomer of rating upto 100 Amps, MCB SPN/DP and MCB SP, 10KA as outgoing and complete connecting cable links with top and bottom removable gland plates with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface and colour coat including taking down old unserviceable DBs complete all as specified and as directed. (Make:- Legrand cat No. 5076 20 4 way /L&T Cat No. DBSPN004GD/ C&S Cat No. CSDBSPNPCGDD04 or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of flush mounting sheet steel enclosure metal clad plug and socket including MCB SP 20 Amps, 10KA 'C' series, 240 Volts after and including taking down of unserviceable one complete all as specified and directed. (Make : Legrand Cat No. 5078 11/Havells Cat No. DHDPUSN020/L&T Cat No. DBMPS220SD or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F in repairs of MCCB, 100 Amps, 4 pole, 16/18KA breaking capacity Icu at 415 Volt with thermal magnetic release, 50 Hz complete all as specified and directed.

S&F of MCB, SP, 6 Amps to 32 Amps , 'C' series, 240 Volt, 10KA, 50 Hz complete all as specified and directed

S&F of MCB SPN 32 Amps, 10 KA, 'C' series, AC, 240Volts, 50Hz complete all as specified and directed.

S&F of MCB, four pole, 40 Amps to 63 Amps, 'C' Series, 415 Volts, 50Hz complete all as specified and directed.

M&L for sub main wiring complete with 2 run of 10 sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FR-LSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of required size medium grade (MMS) with all connected accessories such as Bend, Tee, Elbow, Short pieces etc concealed in wall/roofs/floors and including one run of 10 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FR-LSH type as earth continuity conductor connected to common earth dolly and including chease cutting and filling the same with cement mortar and finished with putty and making good the disturbed surfaces to match with existing surface as required for concealed work including taking down old unserviceable submain wiring complete all as specified and directed.

M&L for sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FR-LSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of required size medium grade (MMS) with all connected accessories such as Bend, Tee, Elbow, Short pieces etc concealed in wall/roofs/floors and including one run of 6 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FR-LSH type as earth continuity conductor connected to common earth dolly and including chease cutting and filling the same with cement mortar and finished with putty and making good the disturbed surfaces to match with existing surface as required for concealed work including taking down old unserviceable submain wiring complete all as specified and directed .

M&L for sub main wiring complete with 2 run of 4 sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FR-LSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of required size medium grade (MMS) with all connected accessories such as Bend, Tee, Elbow, Short pieces etc concealed in wall/roofs/floors and including one run of 4 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FR-LSH type as earth continuity conductor connected to common earth dolly and including chease cutting and filling the same with cement mortar and finished with putty and making good the disturbed surfaces to match with existing surface as required for concealed work including taking down old unserviceable submain wiring complete all as specified and directed . (Note for item No.41.00 to 43.00 : (i)Two runs of cable with one run earth wire and PVC conduit shall be measured as one length. (ii) Extra length of cable required for connection to DBs shall be deemed to be included in the unit rate and shall not be measured separately. (iii) Earth wire shall run inside the conduit. (iv) Suitable color code of wire must be ensured for phase/netural/earth. (iv) All surface cutting/making good for wiring/switch board/junction box/DB etc are included with unit quoted rate.)

M&L for earthing with glavanised steel earth plate electrode of size 600mmX600mmX6mm thick buried directly in ground (earth pit not less than 2.25 m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel using GI or steel wire 4mm dia as earthing lead as shown in electrical plate No.3 of SSR Part-I connected to earthing test point all specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC (1:3:6) type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe , 15mm dia GI medium grade earth lead protection pipe and pre-cast earth pit cover 50mm thick made of RCC (1:1.5:3) type A-1 duly reinforced with 8mm dia TMT bar @150c/c both ways, one lifting handle made out of 10mm dia TMT bar 250 mm long embedded in cover slab and cover, wire, copper lugs etc mesh, charcoal and common salt in alternate layer of 15 cm thick including taking down old earthing complete all as specified and directed. (Notre: Galvanised iron wire of 4mm dia upto 7.5m long including testing is deemed to be included with quoted rate).

M&L for 40 mm bore GI pipe (medium grade) fixed with wall with maximum span of 4.0 meters suitable for hanging of ceiling fan with and including necessary cutting hole in brick/stone wall and making good the same with PCC (1:2:4) type B-1 as required including taking down old unserviceable pipe complete all as specified and directed.

Supply, fabricated and fixing of street light bracket made out of GI pipe 40mm dia medium grade bent to shape of 1.2 mtr long as directed including clamps made out of 30 mm x 6 mm thick -02 Nos flat iron for fixing bracket suitable for steel tubular poles including nuts and bolts, washers and other connected items of required size including painting with two coats of aluminium paint over a coat of red oxide primer including taking down old unserviceable brackets complete all as specified and directed.

S&F of LED security light fitting of capacity 60 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with 4 KV inbuilt surge protector and cable connection from looping box to light fitting and testing and including removing of old unserviceable item complete all as specified and directed. (Make :- SURYA CAT NO-SLE UL 60W IP66LXN/HAVELLS CAT NO. ENDURASUNDOWN SL 60W LED 765PASYBOTG/PHILIPS CAT NO. BRPO 56LED 59CWSLFPSUSL or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F of modular switch 10 Amps, single pole, 1 way, 1 module, 240V, AC including taking down old unserviceable item complete all as specified and directed.

S&F of modular switch 16 Amps, single pole, 1 way, 1 module, 240V, AC including taking down old unserviceable item complete all as specified and directed.

S&F of modular socket shuttered type 6 Amps, 2/3 pin combined 2 module, 240 V, AC including taking down old unserviceable item complete all as specified and directed.

S&F of modular socket 6/16 Amps, 6 pin combined shutter socket, 2 module with light indication, 240 V, AC including taking down old unserviceable item complete all as specified and directed.

S&F of MCB SPN 32 Amps, 10 KA, 'C' series, AC, 240Volts, 50Hz including taking down old unserviceable item complete all as specified and directed.

S&F of 25 watts LED post top decorative lantern (heritage) with LED lamp made in cast aluminium spigot housing with decorative opal polycarbonate diffuser and IP65 protection with suitable fixing arrangements such as lugs, glands, nuts,bolts and washers etc including necessary electric connection with suitable size copper wire after and including taken down of old unserviceable fittings complete all as specified and directed. Make : Havells Cat No. RUBYPT25WLED830SSYMTOPC/ Surya Cat No SLEPT25WETPP/ Bajaj Cat No BGCTN25WLEDWW or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

Supply and fixing 70 watts LED post top lantern (Heritage) made in cast aluminium spigot housing with decorative opal polycarbonate diffuser and IP65 protection. Resistant to impact and corrosion, glare free and better uniformity and providing suitable fixing arrangements such as lugs, glands, nuts bolts, washers and PCC foundation for pipe of required size complete all as specified and directed. (Make:- BAJAJ Cat No. BGCL 70W LED WH/ Surya Cat No. SLE PT 70W ETPP or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of 120 watt LED flood light fitting wtih LED lamp secondary optics made in pressure die cast housing and heat sink in aluminium extrusion with IP66 protection with inbuilt surge protector and cable connection from looping box to light fitting and testing after and including taking down of old unserviceable fittings complete all as specified and directed. Note : Necessary T&P required at site for repair of High Mast light is deemed to be included in quoted rate (Make :- SURYA CAT NO-SLE FL 120W IP66LMS NEO / HAVELLS CAT NO. JETA IRISFL 120W LED 757APWBLTG / PHILIPS CAT NO. BVP192LED110CW HO NB FG GR PSU or equivalent model/Cat No of make as per Appx ‘A’ as mentioned in PS here-in-after)

M&L for boring holes horizontally under road without damaging the surface of road (minimum 1.0m bellow the road surfaces) with the help of GI tubing of any dia not exceeding 80mm dia for passing of UG cable complete all as specified and directed.

M&L for GI pipe 25 mm "light grade" laid in trenches floors/on , pole/road for cable protection with all fittings including taking down old unserviceable one fittings complete all as specified and directed.

Drilling and tapping 20mm cast iron water mains (in position) for branch connections complete all as specified and as directed.

S&F of 20mm dia tubes (medium grade) galvanised iron, with all fittings and fixed laid in trenches or floors including taking down old unserviceable pipe complete all as specified and directed.

S&F of 25mm dia tubes (medium grade) galvanised iron, with all fittings and fixed laid in trenches or floors including taking down old unserviceable pipe complete all as specified and directed.

S&F in repairs of 20mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipes or for unions pipes, fixed complete all as specified and directed.

S&F in repairs of 25mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipes or for unions pipes, fixed complete all as specified and directed.

S&F in repairs of 20mm dia ball brass valve, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Taking down carefully ceiling fans at any height of any sweep/make/model after disconnecting electric connection and dismantling and opening the body of ceiling fan and examine for repairs including servicing, overhauling, greasing etc and cleaning the complete body both internal & external parts with cleaning agent and renewal of minor spare parts such as split pin, cater pins, coupling bolt, capacitor holder, terminal adoptor, screws, nuts, spring washers for blade/body etc and replacement of components/accessories such as ball bearings, gun metal bushes, capacitor, canopy top & bottom, shackle clip assembly and assembling of all parts including hanging and fixing back in existing location and connecting of electrical connections and testing for its satisfoctory performance complete all as specified and directed.

Ditto-all as per Item No.65.00 here-in-above but exhaust fan of PVC/Metal body 250 mm sweep complete all as specified and directed.

Ditto-all as per Item No.65.00 here-in-above but exhaust fan of PVC/Metal body 300 mm sweep complete all as specified and directed.

Ditto-all as per Item No.65.00 here-in-above but exhaust fan of PVC/Metal body 380 mm to 450mm sweep complete all as specified and directed.

Ditto-all as per Item No.65.00 here-in-above but air circulator wall mounted type 450mm to 600mm sweep including carrying out repairs to oscillation mechanism/speed regulation mechanism and making functional performance complete all as specified and directed. {Note for Item No. 65.00 to 69.00 : (i) Spare parts will be measured and paid separately under relevant item of schedule as "Supply only". (ii) Rewinding of fan motor, painting will be measured and paid separately under relevant item of schedule. (iii) Labour charge for taking out and refixing of "Supply only" materials deemed to be included in quoted rate.}

Supply only capacitor 1.5 MFD, 240 volts, 50Hz complete all as specified and directed.

Supply only capacitor 2.5 MFD, 240 volts, 50Hz complete all as specified and directed.

Supply only capacitor 3.15 MFD, 240 volts, 50Hz complete all as specified and directed.

Supply only ball bearing complete all as specified and directed. (Make: SKF Cat No. 6201/6202 or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

Supply only ball bearing complete all as specified and directed. (Make: SKF Cat No. 6203/6204 or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

Supply only gun metal bush suitable for ceiling fan/exhaust fan/air circulator/wall mounted fan any sweep/type complete all as specified and directed.

Supply only shackle clip assembly with rubber bush reel and nuts, bolts and washers suitable for ceiling fan any sweep/type complete all as specified and directed.

Supply only down rod made of MS pipe medium grade 15mm dia of 600 mm long duly drilled holes bot ends & slot with hole in other end suitable for fixing of ceiling fan of any sweep/type and painting to down rod with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply only copper conductor cable, PVC insulated, sheathed, flexible, multistranded, ISI marked, 1100 volts grade 3 core, 1.50 sqmm complete all as specified and directed. (Note for Item No.70.00 to 78.00:- Materials of Item No. 70.00 to 78.00 are to be incorporated in Item No. 65.00 to 69.00 here-in-before )

Cutting the existing surface wall of brick/stone masonary and making round hole at any height suitable for fixing 300 to 450 mm sweep exhaust fan including providing nut, bolt and washers after grouting in PCC including 3mm dia 5cm aperature MS jali of required size fixed in wooden frame to avoid insects, fixed to outer surface of wall and making good the disturbed surface complete all as specified and directed.

M&L for painting to ceiling fan complete body, blades & down rod etc of any sweep/make/model with two coat of synthetic enamel paint by using electric spray gun machine to match with existing colour after preparation surfaces including marking of MES Number with black paint complete all as specified and directed . (Note:-Painting work to be carried out after taking out of ceiling fan)

M&L for painting to exhaust fan complete body, blade assembly,frame etc of 300 mm to 450 mm any sweep /make/model with two coat of synthetic enamel paint by using electric spray gun machine to match with existing colour after preparation of surfaces including marking of MES Number with black paint complete all as specified and directed. (Note:-Painting work to be carried out after taking out of exhaust fan)

M&L for rewinding of ceiling fan motor of 1200 mm sweep of any make/model/type with new supper enamelled copper winding wire of similar gauge and number of turns as existing, including cleaning the motor properly and applying varnishing heating and assembling of fan motor and rotor fixing back after testing including removing burnt out copper winding wire from ceiling fan motor complete all as specified and directed.

M&L for rewinding of ceiling fan motor of 1400 mm sweep of any make/model/type with new supper enamelled copper winding wire of similar gauge and number of turns as existing,including cleaning the motor properly and applying varnishing heating and assembling of fan motor and rotor fixing back after testing including removing burnt out copper winding wire from ceiling fan motor complete all as specified and directed.

M&L for rewinding of exhaust fan motor of 250mm sweep to 300 mm sweep of any make/model/type with new supper enamelled copper winding wire of similar gauge and number of turns and assembling of fan motor and rotor fixing back and testing including removing burnt out copper winding wire complete all as specified and directed.

M&L for rewinding of exhaust fan motor of 380mm sweep to 450 mm sweep of any make/model/type with new supper enamelled copper winding wire of similar gauge and number of turns and assembling of fan motor and rotor fixing back and testing including removing burnt out copper winding wire complete all as specified and directed.

M&L for rewinding of air circulator fan motor 450 mm sweep to 600 mm sweep of any make/model/type with new supper enamelled copper winding wire of similar gauge and number of turns as existing,including cleaning the motor properly and applying varnishing heating and assembling of fan motor and rotor fixing back after testing including removing burnt out copper winding wire from air circulator fan motor complete all as specified and directed.

Taking down storage type water heater (Geyser) 25 Ltrs capacity of any make/model/type from existing wall after disconnecting of electric and water supply connections and keeping the same in safe custody for carry out repairs/replacement of unserviceable spare parts & components such as heating element, thermostat,pilot lamps with wiring,insulating glass wool, thermal cut out,pressure release valve,safety valve,aperature plate assembly etc and exmine water tightness of inner storage tank after cleaning and renewal of rubber washer/gasket and nut,bolts and washers etc and adjust to required range of thermostat control and assembling all parts/ accessories including fixing back in same location after connecting up of water & electric connections and testing for its satisfatory functioning complete all as specified and directed. {Note :- (i) Spares will be measured and paid separately under relevant item of this schedule as "Supply only". (ii) Labour charge for taking down and fixing of 'Supply only" materials are deemed to be included in quoted rate. }

Supply only heating element 2.0 KW, suitable for storage tyep water heater complete all as specified and directed.

Supply only thermal cut out suitable for storage type/instant type water heater (geyser) of any type/capacity complete all as specified and directed.

Supply only aperature plate assembly suitable for storage type water heater (geyser) 25 litre capacity complete all as specified and directed.

Supply only copper inner tank suitable for storage type water heater (geyser) 25 litre capacity complete all as specified and directed.

Supply only geyser indicator pilot lamp (red and green lamps) with wiring round/square/rectangle suitable for geysers of any type complete all as specified and directed.

Supply only 15mm dia stainless steel connection pipe , 450mm long with end nuts and washer, suitable for hot water outlet of geyser complete all as specified and directed.

Supply only 15mm dia stainless steel connection pipe, 600mm long with end nuts and washer, suitable for hot water outlet of geyser complete all as specified and directed.

Supply only 15mm dia stainless steel connection pipe, 450mm long with end nuts and washer, suitable for cold water inlet of geyser complete all as specified and directed.

Supply only 15mm dia stainless steel connection pipe, 600mm long with end nuts and washer, suitable for cold water inlet of geyser complete all as specified and directed.

Supply only 15mm dia angular stop valve, cast copper alloy chromium plated with crutch handle screwed both ends for GI pipe/fittings complete all as specified and directed. (Note for Item No. 88.00 to 97.00 :- Materials of Item No. 88.00 to 97.00 are to be incorporated in Item No. 87.00 here-in-before)

M&L for painting to storage type water heater(Geyser) of capacity 25 litre of any make/type to complete external body with two coats of synthetic enamel paint by using electric spray gun machine to match with existing colour after preparation of surfaces including marking MES Number with black paint complete all as specified and directed. {Note:-Painting work to be carried out after taking out of storage type water heater (geyser) }

S&F in repairs ceiling fan hook made out of MS flat iron 40mm x 4mm, bend to shape for hanging ceiling fan with clamps and necessary nuts and bolts to hold the hook and ceiling fan complete all as specified and directed.

MAZUMDER AND CO (BID ID -3119908)

N S CONSTRUCTION (BID ID -3121231)

DAS ENTERPRISE (BID ID -3120528)

TAMALIKA ENTERPRISE (BID ID -3121642)

M/S. NAYABASTI CONSTRUCTION and SUPPLY SYNDICATE (BID ID -3121098)

CHATTERJEE CONSTRUCTION AND SUPPLIERS (BID ID -3121614)

SHARMA CONSTRUCTION (BID ID -3120753)