Modification for provision of A T M Training Facilities S M U Calibration Lab and R and D Centre in existing Terminal Building at Begumpet Airport Hyderabad

Subhead 1 : Interior and Civil Works : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(Zone III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300mm thick AAC blocks in super structure above plinth up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer in Charge.(The payment of RCC band and reinforcement shall be made for saperately

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40mm dia. M.S. tube 1.5m centre to centre horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade. Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and laying Mirror polished machine cut Granite tiles of 8mm thick of approved colour, shade & pattern as floor and border tiles laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) The Rate is inclusive of all wastages, Chamferring of edges and matching with adjacent vitrified tiles.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing and fixing 12 mm thick fire retardant ply wood conforming to IS 5509,to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately) :

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 30 mm thick including ISI marked Stainless Steel butt hinges(size:100X60X2.5mm) with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing stainless steel hanging type floor door stopper Catalogue No: OZ - DST-55E/ SSS finish of make Ozone or equivalent with necessary SS screws, etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood.50x50 mm (base and height)

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.1.0 mm thick

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing MS frame work support for glass partitions for partitions made of hollow MS tubes fixed to ceiling in an approved pattern with required spacing (vertically & horizontally ) with necessary welding at junctions and fixing the frame to wall/ ceiling/ with MS base plate and stainless steel dash fasteners of 8 mm dia, 75 mm long bolt, as per the approved drawing including providing two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.(Cost of MS base plate to be paid for separately.) Contractor shall submit shop drawings before execution of work

Welding by gas or electric plant including transportation of plant at site etc. complete.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing 1st quality Ceramic Glazed wall tiles conforming to IS : 15622 of size 600mm x 300mm (thickness to be specified by the manufacturer) of approved make, in all colours, shades as approved by Engineer-in-Charge in skirting, risers of steps and dados with cement based High polymer modified quick set tile adhesive (water based) conforming to IS:15477, in average 3mm thickness, including pointing in white cement mixed with pigment of matching shade complete

Providing and laying Matt finished vitrified floor tiles (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of tile 600mm x 600mm

Providing and laying Matt Finished vitrified floor tiles (thickness to be specified by the manufacturer) with water absorption less than 0.08% andconforming to IS: 15622, of approved make, in all colours and shades, laid With cement based High polymer modified quick set tile adhesive(water based) conforming to IS:15477,in average 3mm thickness, including grouting the joints with white cement and matching pigments etc., complete. Size of tile 600mm x 600mm

Providing and laying Glazed Vitrified floor tiles of double charged variant (thickness to bespecified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid With cement based High polymer modified quick set tile adhesive (water based) conforming to IS:15477,in average 3mm thickness, including filling / grouting of joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg),and finishing complete as per direction of Engineer-in-charge. Size of tile 600mm x 600mm

Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mmx100mmx3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product. a) 300 mm Finished Floor Height (FFH)

Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mmx100mmx3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product. 450 mm Finished Floor Height (FFH)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 & 7) in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @ 120 gsm) comprising of main T runners of 15X32mm of length 3000mm, cross T of size15X32mm of length 1200mm and secondary intermediate cross T of size 15X32mm of length 600mm to form grid module of size 600X600 mm suspended from ceiling using galvanized mild steel item (galvanized @ 80gsm) 50mm long 8mm outer diameter M-6 dash fasteners, 6mm diameter fully threaded hanger rod upto 1000mm length and L-shaped level adjuster of size 85X25X2mm spaced at 1200mm centre to centre along main 'T'. The system should rest on periphery walls/partitions with the help of GI perimeter wall angle of size 24X24X3000 mm made of 0.40mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450mm centre to centre & 40mm long dry wall S.S screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. with 20mm thick beveled tegular mineral fibre false ceiling tile(NRC 0.7).

Providing and Fixing 15 mm thick densified tegular edged eco friendlylight weight calcium silicate false ceiling tiles of approved texture ofsize 595 x 595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanised steel sections (galvanising@ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mmand secondary cross ‘T’ of length 600 mm and size 24 x28 mmmade of 0.33 mm thick (Minimum) sheet to be inter locked at middleof the 1200x 600 mm panel to from grid of size 600x600 mm, restingon periphery walls /partitions on a Perimeter wall angle pre-coated steel of size (24x24X3000) mm made of 0.40 mm thick (minimum)sheet with the help of rawl plugs at 450 mm centre to centre with 25mm long dry wall screws @ 230 mm interval and laying 15 mmthick densified edges calicum silicate ceiling tiles of approved texturein the grid, including, cutting/ making opening“for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at1200 mm centre to centre along main ‘T’, bottom exposed with 24mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed byEngineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), lightreflection > 85%, non- combustible as per B.S. 476 part IV, 100%humidity resistance and also having thermal conductivity <0.043 w/mK.

12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : With cement mortar 1:4 (1cement: 4 coarse sand)

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 5.5 mm

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : Old work (one or more coats)

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade :One or more coats on old work

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sq. metres and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

Dismantling old Dado including plaster raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : Bituminous road

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : Up to 10 mm thick

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : Thickness above 10 mm up to 25 mm

Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead : 75 to 80 mm dia pipe

Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead : 100 mm dia pipe

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing white vitreous china flat back sensor urinal of make CERA Model No: 5005A or equivalent of approx. size 740X360 x 330mm with integrated EFS having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work exposed on wall : 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work Exposed on wall . 25 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps i/c making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall. 15 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps i/c making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall. 20 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore

Providing and fixing uplasticised PVC connection pipe Model No: 3618 of Viking make or equivalent with CP brass unions : 45 cm length 15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :20 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :25 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 25 mm nominal bore, 152mm long. Weighing not less than 440 gms.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately. For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge., Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 6.0 mm thickness

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 3 mm thick

Dismantling of wash basin of any size including stacking of useful materials and disposal of unserviceable material within 50mts lead

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes within 50 metres lead as per direction of Engineer- in-Charge. (a) Internal Work - Exposed on wall

Providing and fixing plain mirror of 5mm thick of required size (of approved quality, Modi Guard/Saint gobain or equivalent) fixed to wall with 20 x 25mm Stainless steel studs including making necessary holes to glass and the wall and including wooden plugs etc complete as per the direction of E I C

Providing and fixing on wall face unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes 110mm diameter

Providing and fixing on wall face unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes 75mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Bend with door - 110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Bend with door - 75mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Plain Bend - 110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Plain Bend - 75mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Door Y 110x110x110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Door- Y 75x75x75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Plain -Y 110x110x110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Plain -Y 75x75x75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single tee with door- 110x110x110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single tee with door -75x75x75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Plain tee - 110x110x110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Plain tee 75x75x75 mm

Providing and fixing PVC moulded fittings/ accessories: Plain Floor Trap with out jali 75mm.

Providing and fixing white vitreous china wall hung water closet with integrated P-trap, rubber connector, rack bolt for fixing with soft closing Seat cover of Hindware Cornice catalogue no. 92504 or equivalent with seat and lid, complete, with necessary fittings and fixtures including making necessary connections, cutting and making good the walls and floors wherever required.( Cost of Rack Bolt to be paid separately)

Providing and fixing white vitreous china wash basin of oval shape below counter type 550x400mm or nearest size. Parryware make ( product code No : C0407 ) or equivalent

Providing and fixing 12 mm thick compact laminate Urinal partitionof height 1195 mm to 1200 mm and width 450mm to 500mm with SS 304 grade accessories of make Greenlam Model A or Merino UMP SS series or equivalent as approved by Engg-in-charge.

Providing and fixing C.P. brass pillar Cock 15mm nominal bore with auto closing system 65 mm extension body Jaquar make (product Code PRS-CHR-031L65 ) or equivalent as approved by Engg-in-charge.

Providing and fixing CP brass bottle trap (with internal partition ) 32mm dia size with long wall connection pipe and with flange of Jaquar make Category No: ALE-ESS 773NL 250x250 or equivalent.

Providing and fixing Health Faucet ABS with double lock 1.20 metre long stainless steel flexible hose and wall hook catalouge No: F160001 of Hindware or equivalent

Providing & fixing CP Brass Soap Dispenser. Jaquar make(product Code ACN-1135N) or equivalent.

Providing and fixing C.P. brass 2 way bib cock Model No: CON-CHR-041KNF of Jaquar make or equivalent - 15 mm nominal bore.

Providing and fixing 32mm CP Brass Waste Coupling for wash basin/Urinal Model No: ALD-CHR-705/709 of Jaquar or equivalent.

Providing and fixing C.P. brass Flush Valve Dual Flow 32mm size(Concealed Body) with exposed shut off provision of Jaquar Make circular type (Product Code FLV-CHR-1085) or Equivalent.

Providing and fixing SS Grating of size 100mm of make Viking (Code VKG-40905) or equivalent.

Providing and fixing gun metal gate valve with C.I. wheel (ISI make of Zoloto or equivalent) (screwed end) : 20 mm nominal bore

Providing and fixing Aluminium American Handles (Cat No. EAAAW08 of M/s Everite Agencies or Equivalent) of size 200mm anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing and fixing SS Tower bolt 200mmx10mm Model No: OZ-TB-SE/Grade SS 202-SSS of Ozone make or equivalent of with necessary SS screws etc. complete.

Providing and fixing SS Pull Handle H-Type(pair) size 250x22 mm in two tone finish of Hardwyn make Model No. HPH-141 or equivalent with necessary screws etc. complete :

Providing and fixing Ultra vertibolt-1CK of M/s Godrej (Product Code 5457/ 9839 or equivalent) of size 110mmx73mm with necessary screws etc. complete :

Providing and fixing Mortise Lock of M/s Godrej make Model No. 9158 or equivalent with necessary screws etc. complete :

Providing and fixing 3.00 m high fixed frameless glass internal partitions to form Cubicles and plain wall at all floors with 12 mm thick clear toughened glass of saint gobain/AIS or approved equivalent as per elevation drawings with aluminium wedge profile with SSS finish/PSS finish OGL-PR-22 of make Ozone or equivalent with EPDM gasket OZ-EPDM-44 and OZ-EPDM-33 of make Ozone or equivalent fixed at floor and false ceiling level profile fixed with SS screws of size 10 x 50 mm at spacing of 300mm including necessary filling up gaps at junction and sides of glass with required weather silicon sealant of approved make edge buffing of the glass providing edge cap wherever required etc. complete .(Necessary supporting MS frame work for fixing of wedge section at false ceiling level will be done separately.Glass partition including wedge profile will be measured for payment. All the handling, transportation and insurance charges for glass if required will be borne by the agency.)

Providing and fixing 1800mm wide frameless double leaf swing glass door with over head panel using 12 mm thick toughened glass of Saint Gobain /AIS or approved equivalent fixed with die cast fittings with stainless steel cover of grade 304in SSS finish including fixing of patch fittings, floor springs, locks, handles etc. using the hardware items which include standard Bottom Patch code no.OPF-3 of Ozone or equivalent, standard top Patch code no.OPF-2 of Ozone or equivalent in standard Over head panel side panel connecting patch with pivot code no. OPF-1 Corner Lock OPL-1 Super Floor Spring code no.FS-8400-S of Ozone or equivalent, SS Pull Handle SSS finish 25x450 mm code no OGH -55 of make Ozone or equivalent and other accessories for self closing feature complete in all respects including edge buffing of all sides of glass , mirror polishing and 2mm champferring of exposed edge of door glass as per detailed drawings, manufacturers specifications and direction of Engineer in charge. (Door area excluding over head panel will be measured for payment. All the handling, transportation and insurance charges if required will be borne by the agency.)

Providing and fixing 1000mm wide frameless single leaf swing glass door with over head panel using 12 mm thick toughened glass of Saint Gobain /AIS or approved equivalent fixed with die cast fittings with stainless steel cover of grade 304 including fixing of patch fittings, floor springs, locks, handles etc. using the hardware items which include standard Bottom Patch code no.OPF-3 of make Ozone or equivalent, standard top Patch code no.OPF-2 of Ozone or equivalent standard Over panel side panel connecting patch with pivot code no. OPF-1, Corner Lock OPL-1 Super Floor Spring code no.FS-8400-S of Ozone or equivalent, SS Pull Handle SSS finish 25x450 mm code no OGH -55 of make ozone or equivalent and other accessories for self closing feature complete in all respects including edge buffing of all sides of glass , mirror polishing and 2mm champferring of exposed edge of door glass as per detailed drawings, manufacturers specifications and direction of Engineer in charge. (Door area excluding over head panel will be measured for payment. All the handling, transportation and insurance charges if required will be borne by the agency.)

Providing and Fixing 1200 mm frameless free standing toughened glass (Saint Gobain/AIS or approved equivalent ) partition forming cubicles of 1200 mm height and of required length with mirror polished exposed edges ,fixed as per specified lay out with 150mm high spigot with base SS 304 of Taiton or equivalent make code no. TBF-SG-B-6 fixed with SS anchor fasteners of size 8x100 mm as legs glass to glass connectors 180 degree (code no.OGC-5 of Ozone or equivalent) glass to glass connectors 90 degree (code no.OGC-3 of Ozone or equivalent glass to wall connectors 90degree (code no.OGC - 4 of Ozone or equivalent including necessary accessories as required with nuts etc used as and where required as per layout plan, glass to be of required length with proper support with all gaps filled with silicon sealent of approved make ,Glass to have holes/cut outs to accommodate patch fittings, all complete. ( Area of Glass only to be measured for payment purpose. All the handling, transportation and insurance charges if required will be borne by the agency.)

Providing and fixing Acoustical wall panelling "Optra" of make M/s Armstrong or equivalent with square edges made of fibre glasswool substrate 25mm thick of density 100 kgs/m3 and wrapped on the front side with acoustical transparent and classified for fire reaction class B-s2 , d1 of EN13501-1:2007 fabric with an option of colours as approved by Engineer -in-Incharge of width 600mm and length 600/1200/2100 mm as per approved drawing, providing a maximum sound absorption level of 0.90 NRC, affixed to wall using GI wall panel impellers supplied by M/s Armstrong industries India Pvt. Ltd as per the quantity specified and construction adhsive as per the instruction laid down by the manufacturer. Wall panel impellers shall be fixed to the wall surface using self tapping screws. Silica based construction adhsive shall be dabbed on the projecting elements (spikes ) of the impellers ensuring the line and level of the panels .etc complete. MTC for NRC and fire resistance shall be submitted by the contractor before execution.

Carriage of the Dismantlled Aluminium, wooden partition, glass, pre-laminated particle board, sanitary fixtures & fittings, wooden doors, GI pipes, etc., from the Terminal building to Civil stores by mechanical transport ( 9 Tonner Diesel truck), including loading and unloading and stacking manually. Lead upto 1 km .

Providing and fixing Roller Blinds of of approved size of make MAC (SLM -3724 London Mist) or equivalent with openness factor approximately 5% and the material composition should be of 12% polyester and 88% PVC, Thickness 0.68mm, Breaking strength- Warp>100 daN/5 Cm & Weft>100daN/5 Cm with necessry accessories complete, as per the site condition and as directed by EIC

Providing & fixing Greenlam Sturdo Classique Evergreen model or Merino ZEUS SS series or Equivalent Cubicles of following dimension which includes 600mm door size width made of heat, bacteria, water, chemical, scratch and impact resistant 12mm thick solid compact laminate panels including doors, pilasters & intermediate panels finished with approved texture/shade as per the detail drawings & as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. The product should have Green Guard Certificate.This also includes providing and fixing in position necessary hardware made out of Stainless steel (Grade 304) as per manufacturer’s specifications & Architects instructions like (1) Door Knob, (2) Gravity Hinges, (3) Lockset with indicators, (4) Coat hooks with door stopper (5) U- Channels, (6) Adjustable leg, (7) Top rail hallow circular pipe (8) Corner connector (9) Rubber noise deafening tape for grooves in door & pilasters (10) Wall Bracket (11) Screws & wall Plugs. The top fitting should consist of SS round top rail which will get fixed with pilasters, with SS panel tube holder, SS corner bend (connected with top rail) will be used on the corner of cubicle in absence of brick wall, SS wall fixing is used only on the wall which will hold the ss top rail. All screws will be of 304 Grade in stainless steel with satin finish. All pilasters are supported by stainless steel bottom cladding. The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height upto 150mm. as per direction of Engineer-Incharge. The contractor has to submitt necessary detailed shop drawing before execution of the work. "L" shape Cubicle W- 1000mm to 1200mm D- 1500mm to 1650mm H- 2025mm

Providing & fixing Greenlam Sturdo Classique Evergreen model or Merino ZEUS SS series or Equivalent Cubicles of following dimension which includes 600mm door size width made of heat, bacteria, water, chemical, scratch and impact resistant 12mm thick solid compact laminate panels including doors, pilasters & intermediate panels finished with approved texture/shade as per the detail drawings & as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. The product should have Green Guard Certificate.This also includes providing and fixing in position necessary hardware made out of Stainless steel (Grade 304) as per manufacturer’s specifications & Architects instructions like (1) Door Knob, (2) Gravity Hinges, (3) Lockset with indicators, (4) Coat hooks with door stopper (5) U- Channels, (6) Adjustable leg, (7) Top rail hallow circular pipe (8) Corner connector (9) Rubber noise deafening tape for grooves in door & pilasters (10) Wall Bracket (11) Screws & wall Plugs. The top fitting should consist of SS round top rail which will get fixed with pilasters, with SS panel tube holder, SS corner bend (connected with top rail) will be used on the corner of cubicle in absence of brick wall, SS wall fixing is used only on the wall which will hold the ss top rail. All screws will be of 304 Grade in stainless steel with satin finish. All pilasters are supported by stainless steel bottom cladding. The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height upto 150mm. as per direction of Engineer-Incharge. The contractor has to submitt necessary detailed shop drawing before execution of the work . "I" shape (Front) Partition W-1000mm to 1200mm H-2025

Providing and fixing 3M Scotchal Electro cut Dusted crystal (Acid etched look-7725SE-314) / Frosted crystal (Sand Blasted look-7725SE-324) Graphic Film over the designated locations with wet applications at all floors in any design and pattern complete as per the direction and satisfaction of Engineer-in- charge. (Film area without any deductions for blank area and pattern will be measured for payment.)

Providing and fixing interior designer film of Garware Frosted glass (Sparkle) or equivalent of thickness 100 micron VLT 65-70% over the designated locations with wet applications at all floors in any design and pattern complete as per the direction and satisfaction of Engineer-in- charge. (Film area without any deductions for blank area and pattern will be measured for payment.)

Providing and fixing insulation with Resin Bonded Fibre glass wool conforming to IS: 8183, density 24 kg/m3 , 50 mm thick, wrapped in 200 G Virgin Polythene bags placed behind wall panelling / over existing false ceiling and held in position by criss-crossing GI wire 20 SWG. etc complete.

Spray Painting of aluminium false ceiling with Poly-ur-ethylene paint of make MRF or equivalent to give an even shade with required PU thinner and Two coats of Metal coat as per manufacturers recommendations.:Old Work

Providing and fixing 4 mm thick veneer ofapproved shade and pattern of make Green lam or equivalent to existing frame, backing or studding with screws nails etc. complete :

Melamine polishing on wood work (three or more coats on new work)

Providing and Fixing channeled wood works panelling of approved parttern and shape of M/s Armstrong or equivalent of width 128mm, minimum thickness of 15mm and length 2440 mm or as approved by Engineer-in-incharge , made of a high density particle board substrate of min density 830 kg/m3 with 1mm laminate facing as per the approved shade/ species & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a “Helmholtz” fluted perforation of 2mm width and 14mm of visible panel / 4mm width and 28mm visible panel each. The panels shall provide a minimum sag resistance of RH90 and a fire rating and class of 1 as per Part 7 of BS 476 and Min NRC 0.55. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non-woven acoustical fleece. The panels shall be mounted on special aluminum splines using clips GTPT 001, GTPT002& GTPT003 provided by M/s Armstrong or equivalent. The work shall be got done by Armstrong Recognized Interior Contractor (ARIC).The necessary test reports for quality of the material shall be submitted by the agency before execution of the work.

Supplying Rack bolts catalouge No: 9501 of Viking make or equivalent for fixing WCs etc

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 470x420 mm bowl depth 178 mm

Providing and fixing CP brass Sink cock with Swivel casted Spout (Wall mounted) Catalogue No: F200024FT of Hindware make or equivalent.

Provding and fixing white vitrieous china single piece EWC cum flushing cistern with seat cover of Model : Prince and code No: C0849N/O/P of make Parryware with S trap 280/210/110mm as required with seat cover and in built fittings complete including making necessary connections cutting and making good the floors where ever required

Providing and fixing sanitary fixtures for Differently Abled toilet Matrix set code no.70002 of make Hindware or equivalent comprising one wash basin of size 450x360 mm one pair mounting brackets , one number EWC & Cistern complete with fittings and seat cover one no. hinged rail 76 cm and 4 nos. grab rails 60 cm etc complete.

Preparation of working drawings, service drawings and as built drawings and structural design for certain components of work getting the structural design vetted from approved Govt. Engg college/NIT in respect of the work of ‘Modification for provision of ATM training facilities, SMU , Calibration Lab and R&D Centre in existing Terminal Building at Begumpet Airport, Hyderabad’ including submission of drawings, design etc. in sufficient numbers in hard and soft copies , as per the detailed scope given in particular specification of the item inclusive of all payments to consultant and to Govt. Engg College/NIT etc.complete.

Providing and fixing skirting with Pre-laminated medium density fibre board exterior grade (Grade-I) conforming to IS: 14587:1998 marked, with (one side decorative and other side balancing lamination and edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. all complete: 18 mm thick.

Providing and fixing 18 mm thick BWP grade plywood conforming to IS 710, in lining including priming coat on unexposed surface with necessary fixing arrangements and screws etc complete

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing 18mm BWP Grade Plywood of approved brand conforming to IS 710 for cupboard shutters including fixing to MS frame work with MS butt hinges with necessary screws etc complete. (Cost of MS Butt hinges will be paid for separately)

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. Double strip (horizontal type)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :100x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 100mm

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. Size 50 mm

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces ofshutters: 30 mm thick including ISI marked Stainless Steel butt hinges (size:100X60X2.5mm) with necessary screws

French spirit polishing :Two or more coats on new works including a coat of wood filler

Providing precise cutouts of size 100 mm x 75mm : 200mm x 75 mm : 125mm x 125mm for fixing Module box for electrical switches and sockets in 12mm thick plywood panelling and 1mm thick decorative Laminate provided as wall panelling at the bottom of GYP board partition by mechanical means using power tools etc., complete.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows(Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazedshutters 25 mm to 40 mm thick : Float glass panes4 mm thick glass pane

Providing and fixing reflective suncontrol film having thickness 2 Mil with visible light transmittance 10% and glare reduction 89% of approved shade of make Garware or equivalent

Providing and laying Glazed Vitrified floor tile (thickness to bespecified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid With cement based High polymer modified quick set tile adhesive (water based) conforming to IS:15477,in average 3mm thickness, including filling / grouting of joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), and finishing complete as per direction of Engineer-in-charge. Size of tile 600mm x 600mm

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound@ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b)Second layer of slurry of cement @ 0.242 kg/sqm mixed with waterproofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) : Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

Repairs to existing Gypsum board false ceiling with existing frame work at all heights including fixing of new gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm or both sides of joint and two coats of primer suitable for board, all as per manufacture's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting and Grid System with : 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (a) All works above plinth level up to floor V level.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Sub Head-2: Internal & external electrical works along with earthing and other allied works _______________________________________________ W I R I N G & LIGHTING _______________________________________________ Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. a) Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. a) Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing etc. as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 2 Nos 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing etc. as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required a) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required b) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required c) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required d) 4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required e) 4 X 4 sq. mm + 2 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required f) 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel conduit including dismantling etc. as required. a) Group - C

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit/DLP Trunking/ Mini Trunking etc. as required. a) 2 x 1.5 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit/DLP Trunking/ Mini Trunking etc. as required. b) 3 x 1.5 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit/DLP Trunking/ Mini Trunking etc. as required. c) 2 x 2.5 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit/DLP Trunking/ Mini Trunking etc. as required. d) 4 x 2.5 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit/DLP Trunking/ Mini Trunking etc. as required. e) 2 x 4 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit/DLP Trunking/ Mini Trunking etc. as required. f) 3 x 4 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit/DLP Trunking/ Mini Trunking etc. as required. g) 4 x 4 sq. mm

Supplying and drawing following pair 0.5 sq. mm FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit / PVC Trunking etc. as required. a) 2 Pair

Supplying and drawing following pair 0.5 sq. mm FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit / PVC Trunking etc. as required. b) 4 Pair

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. a) 1 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. b) 2 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. c) 3 run of cable

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit/ PVC trunking etc. as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit etc. as required. a) 20 MM

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit etc. as required. b) 25 MM

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit etc. as required. c) 32 MM

Supplying and fixing of following sizes of UPVC mini trunking/ casing capping conduit along with accessories in surface complete etc. as required. (Make: MK/ Legrand) a) 12.5 x 32 mm

Supplying and fixing of following sizes of UPVC mini trunking/ casing capping conduit along with accessories in surface complete etc. as required. (Make: MK/ Legrand) b) 16 x 32 mm

Supplying and fixing of following sizes of UPVC mini trunking/ casing capping conduit along with accessories in surface complete etc. as required. (Make: MK/ Legrand) c) 20 x 32mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV Antenna Socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Bell push

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. RJ - 45 Cat 6 Jack

Supplying and fixing following size/ modules, GI / Surface box along with modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)

Supplying and fixing following size/ modules, GI / Surface box along with modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm)

Supplying and fixing following size/ modules, GI / Surface box along with modular base & cover plate for modular switches in recess etc. as required. 6 Module (200mmX75mm)

Supplying and fixing following size/ modules, GI / Surface box along with modular base & cover plate for modular switches in recess etc. as required. 8 Module (125mmX125mm)

Supplying and fixing suitable size GI / Surface box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete etc. as required.

Supply of Single phase wall mounted fans of sweep 450mm suitable for operation on 240V, 50Hz Single phase supply

Supply of Single phase Heavy duty exhaust fans of sweep 450mm and 1400 rpm suitable for operation on 240V, 50Hz Single phase supply

Installation, testing and commissioning of ceiling fan, /wall mounted fan including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

MCCB, MCB & DB'S _______________________________________________________ Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle/ panel board / DB, including drilling holes in cubicle panel, making connections, etc. as required. 100 A, 30kA, FPMCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle/ panel board / DB, including drilling holes in cubicle panel, making connections, etc. as required. 125 A, 36kA, FPMCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle/ panel board / DB, including drilling holes in cubicle panel, making connections, etc. as required. 200 A, 36kA, FPMCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle/ panel board / DB, including drilling holes in cubicle panel, making connections, etc. as required. 250 A, 36kA, FPMCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle/ panel board / DB, including drilling holes in cubicle panel, making connections, etc. as required. 400 A, 50kA, FPMCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle/ panel board / DB, including drilling holes in cubicle panel, making connections, etc. as required. 630 A, 50kA, FPMCCB

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator) 4 way (4 + 12), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator) 6 way (4 + 18), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator) 8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. 8 way DB

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. 12 way DB

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole and neutral

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole and neutral

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 100 amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 mill amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 mill amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.. 40 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 mill amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63amps

CABLE TRAYS _______________________________________________________ Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 200 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 200 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays Tee's with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays Tee's with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays Tee's with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 200 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays Tee's with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays Tee's with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 450 mm width X 50 mm depth X 2.0 mm thickness

E A R T H I N G _______________________________________________________ Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt etc. as required.

Earthing with Copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 meter below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and brazing or with 2 sets of brass nut bolt & spring washer spaced at 50mm as required)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 meter below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable etc. as required.

SURGE PROTECTION & VOLTAGE STABILIZATION _______________________________________________________ Supply and fixing of Surge protector for electronic equipment's against transient voltage surges. A) 3 Phase 4 module Surge protector for main protection , Iimp 100kA (equivalent to Model:SP320 Make: Hager) with enclosure etc. complete as required

Supply and fixing of Surge protector for electronic equipment's against transient voltage surges. B) Single phase surge protectors for fine protection (Equivalent to 2P, 2Module Model: SPN208, Make: Hager) etc. complete as required

SITC of 15 kVA , 1 Phase, Static voltage Stabilizer IGBT based with PWM technology with bypass arrangement. Operating Input Voltage 230 +/- 20%: 184—276 V 1Ph, 2 wire Output Voltage: 230 V +/- 1% Type of Cooling: Natural Air Cooled for unbalance supply and load conditions with true reproduction of input voltage wave form complete etc. as required.

SITC of 30 kVA, 3 Phase, Static voltage Stabilizer IGBT based with PWM technology with bypass arrangement Operating Input Voltage 400 +/- 20%: 320—480 V , 3Ph 4 wire Output Voltage: 400 V +/- 1% Type of Cooling: Natural Air Cooled complete etc. as required.

SITC of 1phase 15kVA Isolation transformer Operating Input Voltage 230 V Output Voltage: 230 V +/- 4% Type of Cooling: Natural Air Cooled complete etc. as required.

MV CABLE SUPPLY, LAYING & END TERMINATION _______________________________________________________ Supply of the following Size , XLPE insulated and FRLS Outer sheathed , armored aluminum conductor power cable of 1.1 KV grade with extruded PVC type ST2 sheathed conforming to IS 7098 (Part - I) with up to date amendment etc. complete as required. 3.5 x 35 sq. mm

Supply of the following Size , XLPE insulated and FRLS Outer sheathed , armored aluminum conductor power cable of 1.1 KV grade with extruded PVC type ST2 sheathed conforming to IS 7098 (Part - I) with up to date amendment etc. complete as required. 3.5 x 50 sq. mm

Supply of the following Size , XLPE insulated and FRLS Outer sheathed , armored aluminum conductor power cable of 1.1 KV grade with extruded PVC type ST2 sheathed conforming to IS 7098 (Part - I) with up to date amendment etc. complete as required. 3.5 x 95 sq. mm

Supply of the following Size , XLPE insulated and FRLS Outer sheathed , armored aluminum conductor power cable of 1.1 KV grade with extruded PVC type ST2 sheathed conforming to IS 7098 (Part - I) with up to date amendment etc. complete as required. 3.5 x 185 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe etc. as required. Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe etc. as required. Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe etc. as required. Above 95 sq. mm and upto 185 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe etc. as required. Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct etc. as required. Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct etc. as required. Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct etc. as required. Above 95 sq. mm and upto 185 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct etc. as required. Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface etc. as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface etc. as required. Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface etc. as required. Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface etc. as required. Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray etc. as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray etc. as required. Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray etc. as required. Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray etc. as required. Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and making end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed / XLPE aluminum conductor cable of 1.1 KV grade etc. as required. 3½ X 25 sq. mm (28mm)

Supplying and making end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed / XLPE aluminum conductor cable of 1.1 KV grade etc. as required. 3½ X 35 sq. mm (32mm)

Supplying and making end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed / XLPE aluminum conductor cable of 1.1 KV grade etc. as required. 3½ X 50 sq. mm (35mm)

Supplying and making end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed / XLPE aluminum conductor cable of 1.1 KV grade etc. as required. 3½ X 95 sq. mm (45mm)

Supplying and making end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed / XLPE aluminum conductor cable of 1.1 KV grade etc. as required. 3½ X 185 sq. mm (57mm)

Supplying and making end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed / XLPE aluminum conductor cable of 1.1 KV grade etc. as required. 3½ X 240 sq. mm (62mm)

Design, Fabrication, Supply, Installation, Testing and Commissioning of cubicle type Indoor LT panel, IP42, fully compartmentalized, suitable for 415V, 3 Phase, 4 wire 50 Hz supply system fabricated in CRCA sheet steel of 2 mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having TPN Aluminum alloy bus bars for high conductivity, DMC/SMC bus bar supports, entire panel shall have a common GI earth bar of size 25 mm x 5 mm at the rear with 2 No's. earth stud, solid / flexible connections from main bus bar to switchgears with required size of AL conductors / bus bars and control wiring with 2.5 sqmm PVC insulated copper conductor cable (FRLS), cable alleys, cable gland plates in two half, i/c providing following switchgears / accessories as per specifications. _________________________________________________________________ Incoming - 2nos - 4 P MCCB 400A 36 kA Thermal Magnetic base, front operated rotary handle with door interlocking Bus coupler - 1no - 4 P MCCB 400A 36 kA Thermal Magnetic base - with 3 lock 2 key interlocking system, front operated rotary handle with door interlocking Outgoing - 6nos - 4 P MCCB 100A 30 kA Thermal Magnetic base, front operated rotary handle with door interlocking RYB LED Indication Lamp for all I/C & O/G with protective SP MCB Set of CTs for metering & protection Digital multi function meter to indicate currents, phase and line voltages, frequency, power factor, KWH, KVARH (EM 6436 / Equivalent) - 2 nos Digital Ammeters - 6 nos for O/G Separate Cable alley for cable termination provided with suitable size terminal connector, neutral bus bar and earth bus bar

Design, Fabrication, Supply, Installation, Testing and Commissioning of cubicle type indoor LT panel, IP42, fully compartmentalized, suitable for 415V, 3 Phase, 4 wire 50 Hz supply system fabricated in CRCA sheet steel of 2 mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having TPN Aluminum alloy bus bars for high conductivity, DMC/SMC bus bar supports, entire panel shall have a common GI earth bar of size 25 mm x 5 mm at the rear with 2 No's. earth stud, solid / flexible connections from main bus bar to switchgears with required size of AL conductors / bus bars and control wiring with 2.5 sqmm PVC insulated copper conductor cable (FRLS), cable alleys, cable gland plates in two half, i/c providing following switchgears / accessories as per specifications. __________________________________________________________________ Incoming - 1no - 4 P MCCB 800A 36 kA Thermal Magnetic base, front operated rotary handle with door interlocking. Outgoing - 4nos - 4 P MCCB 100A 30 kA Thermal Magnetic base, front operated rotary handle with door interlocking. Outgoing - 2nos - 4 P MCCB 250A 36 kA Thermal Magnetic base, front operated rotary handle with door interlocking. RYB LED Indication Lamp for all I/C & O/G with protective SP MCB Set of CTs for metering & protection Digital multi function meter to indicate currents, phase and line voltages, frequency, power factor, KWH, KVARH (EM 6436 / Equivalent) - 1 no Digital Ammeters - 6 nos for O/G Separate Cable alley for cable termination provided with suitable size terminal connector, neutral bus bar and earth bus bar

Design, Fabrication, Supply, Installation, Testing and Commissioning of cubicle type indoor LT panel, IP42, fully compartmentalized, suitable for 415V, 3 Phase, 4 wire 50 Hz supply system fabricated in CRCA sheet steel of 2 mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having TPN Aluminum alloy bus bars for high conductivity, DMC/SMC bus bar supports, entire panel shall have a common GI earth bar of size 25 mm x 5 mm at the rear with 2 No's. earth stud, solid / flexible connections from main bus bar to switchgears with required size of AL conductors / bus bars and control wiring with 2.5 sqmm PVC insulated copper conductor cable (FRLS), cable alleys, cable gland plates in two half, i/c providing following switchgears / accessories as per specifications. __________________________________________________________________ Incoming - 1no - 4 P MCCB 400A 36 kA Thermal Magnetic base, front operated rotary handle with door interlocking. Outgoing - 4nos - 4 P MCCB 100A 30 kA Thermal Magnetic base, front operated rotary handle with door interlocking. RYB LED Indication Lamp for all I/C & O/G with protective SP MCB Set of CTs for metering & protection Digital multi function meter to indicate currents, phase and line voltages, frequency, power factor, KWH, KVARH (EM 6436 / Equivalent) - 1 no Digital Ammeters - 4 nos for O/G Separate Cable alley for cable termination provided with suitable size terminal connector, neutral bus bar and earth bus bar

RO Water Coolers _______________________________________________________ SITC of RO Water purifier cum cooler including the following features & delivery at site complete etc. as required. (Make: Aquagaurd/Bluestar/Equivalent) a) with inbuilt RO filter capacity of atleast 50 LPH & with multi levels of water purification. b) with Normal & cold water dispensing options c) with storage tank of atleast 80 Liters capacity d) suitable for treating Salt/Bore-well water e) Stainless steel body - SS-304, Floor standing unit g) Suitable for operation on 240V , 50 Hz AC supply f) With automatic water level cut off & self flushing RO

Sub Head - 3 : Providing Cable Management System with Under Ground Type Raceways, DLP Trunking and other allied accessories for Power & Data Circuit _______________________________________________________ Supply, laying and fixing of following size under floor raceway made up of GI 1.6 mm thick with suitable Fixing bracket (GI), coupler for joining raceways including Cutting the existing CC floor with tiles, with floor cutting machine, in a neat and fashionable manner to make a chase of suitable size for laying of the below mentioned raceways and junction boxes, disposing off the debris, making good the chase after laying the GI under floor race way and access etc. as required. a) 225 mm (W) x 38 mm (H) with 3 compartment (Make: MK/Legrand)

Supply, laying and fixing of following size under floor raceway made up of GI 1.6 mm thick with suitable Fixing bracket (GI), coupler for joining raceways including Cutting the existing CC floor with tiles, with floor cutting machine, in a neat and fashionable manner to make a chase of suitable size for laying of the below mentioned raceways and junction boxes, disposing off the debris, making good the chase after laying the GI under floor race way and access etc. as required. b) 50 mm (W) x 38 mm (H) with 1 compartment (Make: MK/Legrand)

Supply and fixing of following accessories for the above GI under floor race way complete as required. a) Height adjustable Junction Box with fly over / cross over, made up of GI sheet steel 1.6 mm thickness, size 225 x 225 x 65-75 mm or size as suitable for 225x38 Raceway, complete as required (Equivalent to Model 6896 14 Legrand/ Equivalent in MK)

Supply and fixing of following accessories for the above GI under floor race way complete as required. b) Height adjustable Junction Box , made up of GI sheet steel 1.6 mm thickness, size 150 x 150 x 65-75 mm, or size as suitable for 50x38 Raceway, complete as required (Equivalent to Model 6896 10 Legrand/ Equivalent in MK)

Supply and fixing of following accessories for the above GI under floor race way complete as required. c) Floor access outlet box, Height adjustable 65-90 mm, for screed flooring made up of GI sheet steel 1.6 mm thickness of size suitable for raceways upto 225 mm width 3 compartments. (Equivalent to Model 6896 34 + 6896 31 Legrand/ Equivalent in MK)

Supply and fixing of following accessories for the above GI under floor race way complete as required. d) Pop up Box made up of GI with steel finish of 120 x 120 mm x 45 mm provided with 01 no JR - 45 & 01 nos 5 amps socket outlet.

Supply and fixing of following accessories for the above GI under floor race way complete as required. e) Vertical access box made up of GI sheet steel 1.6 mm thickness of size: 225 width raceways. (Model 689723 Legrand / Equivalent in MK)

Supply and laying including fixing of DLP -U/PVC trunking system of following size with required accessories (Full cover, Flat, internal & external angles, junctions, end caps , body and end joints) (Make: Legrand /MK) a) 100 mm x 50 mm

Supply and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing GI Raceway/ recessed steel / U-PVC trunking as required a) 3 x 4 Sq. mm FRLS copper Cable

Supply and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing GI Raceway/ recessed steel / U-PVC trunking as required b) 3 x 6 Sq. mm FRLS copper Cable

Supply and fixing following modular switch / socket on the existing modular plate & switch box / including connections but excluding modular plate suitable for the above Access/ pop up box of raceways/ DLP trucking etc. as required a) 6 amps 1 way Switch

Supply and fixing following modular switch / socket on the existing modular plate & switch box / including connections but excluding modular plate suitable for the above Access/ pop up box of raceways/ DLP trucking etc. as required b) 16 amps 1 way Switch

Supply and fixing following modular switch / socket on the existing modular plate & switch box / including connections but excluding modular plate suitable for the above Access/ pop up box of raceways/ DLP trucking etc. as required c) 3 pin 6 amps universal Socket Outlet

Supply and fixing following modular switch / socket on the existing modular plate & switch box / including connections but excluding modular plate suitable for the above Access/ pop up box of raceways/ DLP trucking etc. as required d) 6/16 amps universal Socket Outlet

Supply and fixing following modular switch / socket on the existing modular plate & switch box / including connections but excluding modular plate suitable for the above Access/ pop up box of raceways/ DLP trucking etc. as required e) RJ - 45 Cat 6 jack

Supply and fixing of mounting plate of 8module (or 3M + 3M + 2 M) suitable for integration of switches and sockets in the under floor access out let boxes complete with all accessories etc. as required.

Sub Head 4 : SITC of Fire Alarm System & Fire Extinguishers _______________________________________________________ SITC of Intelligent Analog Addressable,Multi Criteria type Detector, Complete with dual LED, Hard Addressable: 1-99 complete with Mounting Base Confirming to BS5839 STD, approved by LPCB/EN54.Height 61mm installed in base and Diameter 102mm installed in base. Detectors shall conform to EN54-7, a 58°C fixed temperature and rate of rise thermal assistance, conforming to EN54-5. The thermal detection function shall combine thermistor technology with a software corrected linear temperature response. In areas where the normal daytime activities may potentially create unwanted alarms, it should be possible to program the detector to operate in a “heat only” mode, automatically reverting to full photo-thermal operation during unoccupied periods. Detector shall function as Heat sensor - Class A1R.No Software/ Special Tools/ Hard/Soft shall be required for Programming the Detector. Mounting Bases Shall be common to all detectors, complying the technical specification attached. Part Code: MI/PTSE/S2/IV and MI/B501/AP / Morley IAS Honeywell/ Equivalent

Supply, installation, testing & commissioning of 5 Loop Micro processor based 2 wire fault tolerant loop, (excluding loop driver card) , required loop networkable type (each loop accessing maximum 99 detectors and 99 modules ) fire alarm/detection control panel. The panel shall be able to give location of all fire/fault conditions of addressable units via the address codes. Further, the panel must be able to automatically switch ON /OFF respective control module when ever any alarm is triggered. The panel shall have rectifier, Loop cards, 80 character L C D unit to indicate Fire/Fault Signal with address and analog output, .The Panel Shall be Sheet Steel Painted, sealed to IP30. The Panel Shall have 20 Zones with Individual LED Indicators, expandable to 80 LED Indicators. The Panel Shall have 3 Serial Ports. The panel shall have a built in power supply and battery charger along with maintenance free 24 AH, 2 x 12 volt SMF Lead acid batteries capable of running for a minimum of 24 hours with battery charger complete as required and as per specifications conforming to BS5839 Standards and Duly Approved by EN54/LPCB. Panel and all FAS components shall be from the same manufacturer and branded components are not acceptable, complying the technical specification attached, complying the technical specification attached. Part Code:720-001-301 - Morley IAS Honeywell/ Equivalent

Loop driver card for Morley-IAS protocol/ Equivalent, 460mA. Part Code:795-072-100 - Morley IAS Honeywell/ Equivalent

RS 485 Communication module for Networking Conforming to BS5839 Standards and Duly Approved by EN54/LPCB complying the technical specification attached. Part Code:795-004-001 - Morley IAS Honeywell/ Equivalent

Response indicator for all detectors located above/below false ceiling

SITC of Intelligent Analog Addressable Type Manual Call Point with Surface or Flush Mounting Option with Rotary Decade Switches for addressing from 1-99. MCP shall comply with BS5839 Standard and shall be UL/EN54/LPCB approved. Manual Call Point Shall be Fully compliant with EN54, Part 11. No Software/ Special Tools/ Hard/Soft shall be required for Programming. Part Code: MI/MCP/FLEX. - Morley IAS Honeywell/ Equivalent

SITC Of Addressable Type Loop Powered Hooter Cum Strobe complete with Mounting Base as required conforming to BS5839 Standards and Duly Approved by EN54/LPCB. Convectional Horn and Strobes with Control Modules is not acceptable.: WSS/PR/NO5 and MI/B501/AP - Morley IAS Honeywell/ Equivalent

SITC of Addressable Duct Smoke Sensor with Duct Chamber, Addressable Photo Electric Smoke Sensor & Sampling tube as per site requirement with Rotary Decade switch to address the detectors. The Product has to be EN54/ UL Approved. Part Code :DNRE +DST-1.5+MI-PSE-S2-IV/ Morley IAS Honeywell/ Equivalent

SITC Fault isolator Base /module capable of monitoring shorted loop circuit and automatically restore communications when shorted conditions are corrected (Model: B524IEFT-1/ Morley IAS Honeywell/ Equivalent) The Module have to be LPCB/VDS Approved

Supply, Installation, Testing & Commissioning of UL Listed addressable directional sounder with inbuilt amplifier to produce a sound consisting of Low-Mid-High range of sounds in particular pattern. The noise pattern shall be such that it will be possible for occupants to find out from where the sound is coming. The unit shall consists of minimum four numbers of pulse pattern with facility of adding minimum three additional tones to each of four pulse pattern. The unit shall be tapped for four different watts outputs. (Model: PF 24V) Make: System Sensor/ Equivalent

SITC of Auto dialer for Dialing 10 Preprogrammed numbers in case of Emergency, with a 20 second voice message and compatibility to work on EPABX as well. The dialer should come with 5 Year warranty Part code: Pinnacle Auto dialer/ Equivalent

Supplying, installing, testing and commissioning Laying of 2Cx1.5 sqmm, FRLS PVC Insulated armored cable with clamps screws etc. complete as required ISI STD (Approx.)

SITC of Fire Extinguishers _______________________________________________________ Supply , Installation, Testing and commissioning of CO2 Type 4.5kg capacity fire extinguishers filled with CO2 gas as per IS15222 with control discharge mechanism (wheel type valve) fitted with 1mtr…hose and horn applicable on class B,C and electrically started fire with rating of 21B confirms to IS 15683,bearing seamless..co2 cylinder as per IS 7285 with PESO approval bearing ISI mark.

Supply, Installation, Testing and Commissioning of Dry Chemical 6 Kgs.Fire Extinguisher with SBC powder Cartridges operated ( 120 GM IS 4947 ISI MARK ) with Controllable discharge mechanism Class B rating 21B as per IS 15683 ISI MARK .

Subhead 5 :Deduction Items -Interior & Civil works _______________________________________________________ Deduct for not providing 12.5mm thick Fire Rated Gypsum board in double layer in Gypwall partition at Bottom level or other specified places under item no.132 & 133

Deduct for not providing 12.5mm thick Fire Rated Gypsum board single layer in Gypwall partition above false ceiling level or other specified places under item no.132 & 133

Deduct for not providing 12.5mm thick Gyptone Quattro 41 board in Wall lining at Bottom level or other specified places under item no. 134

Chabbras Associates

CIPEL