Provn of store shed for BSO (S) Tez, storm water drain inside DCN Node, Misc B/R wk at 5 TAC AF, parking shed at Laxam Marg, hard standing, path tilling of HQ 4 Corps, interlocking paver block Stn HQ Tez and Spl rpr to T-34 at 118 FHO under GE (S) T

Amount

Surface excvation n.exe 30 CM deep and avg 15CM deep and getting out in soft/loose soil

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation and getting out in hard/dense soil.for fdn etc

Returning, filling incl spreading levelling watering and well ramming in layers not exc 25 cm for soft/lose soil.

Removing excavated material n exc.50 m and depositing where directed at a level n exc 1.5 m above the starting point in soft/loose soil all as specified and as directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering including watering and consolidation complete all as specified and directed.

M&L for Sand Filling under floors ,paver block or in foundations including watering and consolidation as directed by Engr -in-Chrage.

M&L for Hardcore of guage n exe. 63mm of broken stone or boulders deposited spread and levelled in layers n exe 15 CM thick watered and rammed to a true surface.

M&L for PCC 1:4:8 type D2 (40mm graded aggregate) as in foundation, filling and mass concrete.

Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area

Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured)

Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall

M&L TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders cut to length, bent to shape required including cranking bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete.

M&L mild steel bars 10 mm dia and over cut to length, bent to shape required including cranking bending spirally for hoping for columns, hooking ends and binding with mild steel wire complete.

M&L mild steel bars 6 to 8 mm dia and over cut to length, bent to shape required including cranking bending spirally for hoping for columns, hooking ends and binding with mild steel wire complete.

M&L Reinforced cement concrete M 25 Design Mix (20 mm aggregate) including rafts footings, foundation beams, plinth beam base for column etc basement slab, under reamed piles and mass concrete all as specified.

M&L Reinforced cement concrete M 25 Design Mix (20 mm aggregate) including Beams, cantilevers, bressummers, lintels over 1.5m span complete.

M&L Reinforced cement concrete M 25 Design Mix (20 mm graded aggregate) as in coloumn, pillar, pier, posts etc complete.

M&L Reinforced cement concrete Nominal Mix type B1 1:2:4 (20 mm graded aggregate) as in chajjas etc complete.

Use & waste form work for flat fair finished surfaces of concrete foundation, footings, bases of columns and plinth beam and similar work for rough finished flat surfaces of concrete.

Use & waste form work to sides of pillars,posts, struts, piers, columns and stanchions of square, rectangular on polygonal shape for rough finished surfaces of concrete.

Use & waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. of rough finished flat surfaces of concrete.

Formwork to chullah hoods, chajjas,troughs and similar items including edges of rough finished flat surfaces of concrete.

Material and labour for old size fly ash /concrete best quality bricks, straight or curved on plan exc 6 m mean radius built in cement mortar ( 1:6) having compressive strenght not less than 75 kg/Sq cm all as specified and directed.

Material and labour for old size fly ash /concrete best quality bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar ( 1:6) having compressive strenght not less than 75 kg/Sq cm all as specified and directed.

M&L for 100 mm thick PCC 1:3:6 type C2 using (40 mm graded aggregate) as in as in sub base complete all as specifed and as directed.

M&L for 100mm thick PCC 1:3:6 type C2 (40mm graded aggregate) as in footpath finished even and smooth without using extra cement.

M&L 75mm th PCC 1: 3:6 type C2 using 40mm graded agg fininshed even and smooth without using extra cement as in plinth protection/path and laid fair in alternate bays.

M&L Machine pressed precast concrete interlocking paver block (Glazed finish )with Grey cement and pigment any shape any size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade.

M&L cement concrete 1:2:4 type B1 ( using 20 mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over 20mm thk cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado over 10mm thk cement screed base in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L Damp proof course 25 mm to horizontal or vertical surfaces including necessary formwork In cement concrete 1:2:4, type B-0 all as directed.

M&L for Providing, cement concrete Type B0 1:2:4 , 12.5mm graded aggregate in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

Material and labour for 15 mm thick rendering in cement mortar (1:4) on fair face of brick or concrete surface finished even and smooth without using extra cement.Complete all as specified and as directed by Engineer-in-charge.

Material and labour for 10 mm thick rendering in cement mortar (1:6) on fair face of brick or concrete surface finished even and smooth without using extra cement.Complete all as specified and as directed by Engineer-in-charge.

Supply only integral water proofing compound complete all as directed.

S&F of joist, channel, angle, flat iron or Tee sections, fixed independently with connecting plates, etc confirming to Fe 410-W (Gde 250 quality A) complete all as specified and directed.

S&F Mild steel framed work as in grills, with ends of bars shouldered work conforming to Fe-410-0 as per existing grills at site and directed by Engr-in-Charge.

S&F pre-painted galvalume aluminium zink coating GI based high profile steel sheet 0.50 mm thick of an colour having tensile stenght of 550 MPA as in roof covering /cladding to wall, fixed with self tapping screws as specified.

S&F pre-painted galvalume aluminium zink coating GI based plain steel sheet 0.50 mm thick of an colour having tensile stenght of 550 MPA as in roof covering /cladding to wall, fixed with self tapping screws as specified.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10 cm width or girth complete all as specified and as directed.

M&L preparation of newely plaseter surfaces and appplying two coats of weather coat(Apex) over two primer coats of damp shealth to new plastered walls as per manufacturer and apllied by approved applicator complete all as specified and directed.

M&L Applying two coats of Oil bound distemper to newly plastered/previously untreated wall over a coat of 1 mm layer wall care putty over a coat of primer including preparation of newly platsered wall all as specefied and directed.

Supplied and fixed Pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified,

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

S&F Anodised aluminium frame (three track) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Anodised aluminium window and ventilator shutters, sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws,4mm plain glass and stainless steel wirmesh 0.36mm nominal dia of wire and average width of aperture 1.40mm etc.complete all as specified.

Steel rolling shutters, with out ball bearing,thickness of lath 1.25mm as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated but gear operated type with bevel gear box and crank handle comlete all as specified and directed.

S&F 2nd class hard wood small fitting such as brackets of any type latch and hinge blocks,shaped door and window stops and the like including all necessary labours articles exe. 200cu.cm and n.exe 500 cu.cm each

S&F aluminium anodised sliding door bolts of size 300 mm long with haps and staple (bolt type) and fixing clips of sheet,cast or extruted sections and fixing bolts and sliding bolts of extruted sections of cast type aluminium alloy.

S&F Butt hinges medium weight cold rolled mild streel and fixed size of hinges 50mm

S&F Aluminium anodised barrel tower bolts of extruded section 150 mm long and fixed with screws.

S&F extruded aluminium alloy handels fabricated type, anodised, 150mm long.

Returing filling including spreading levelling two layer not exc 25 cm thick watering and well ramming complete.

M&L pre cast RCC (1:2:4) type B1 using 20 mm graded stone aggregates for cover slab of manhole/soak pit etc set in cement mortar 1:4 complete all as specified and as directed by Engr-in-Charge.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in surface channels, drains complete all as specified and directed.

M&L 2nd CL HW plain fillets square, rectangular or triangular in section clean sawn sectional area exe 6 sqcm & n exe 13 sqcm fixed with nails

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm tick creed bed in cement mortar (1:6) complete all as specified and as directed

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36sqm, in Skirting/Dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick rendering in CM 1:4.

S&F Exposed GI powder coated snap grid frame for false ceiling 600x600mm size of wall angle 25x25x0.25mm size of cross tee and main tee 26x24x0.25mm and 32mm x 24mm x 0.25mm with 1.5mm dia double GI suspentor including supply and fixing of 4mm thick E Board decorative type in false ceiling including fixing arrangement from steel tress any type of tress (Make: E Board of approved make.

S&F 2nd class hard wood plain, solid, striaght in chowkats and framed rebated on the solid rounded or chamfered put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement.

S&F 100mm Butt hinges 100mm long medium weight cold rolled mild steel complete all as specified and directed.

S&F 75mm Butt hinges 75mm long medium weight cold rolled mild steel complete all as specified and directed.

S&F 35mm thick 2nd class hard wood factory made flush shutter solid core construction with block board core and plywood face panels commercial type of both side

S&F 125 mm Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

M&L for 18/19 mm thick plywood BWR grade type fixed wirh screws to timber frame all as specified and as directed.

Taking down cement plaster, of any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water all as directed.

M&L Applying two coats of Oil bound distember to newly plastered/previously untreated wall over a coat of 1 mm layer wall care putty over a coat of primer including preparation of newly platsered wall all as specefied and directed.

M&L preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer.

Surface excavation n.exc. 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil.

Excavation in post holes each n.exc 0.5Cum getting out in soft loose soils, returning filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm and removing surplus soil to ad distance n.exc 50m and making good surface.

M&L PCC (1:4:8) type D2 using 40mm graded aggregate 75mm thick in sub base complete all as specified and as directed.

M&L 40mm thick PCC type B2 (1:2:4) of 20 mm graded aggregate as in flooring etc. incl finishing the concrete surface even and rough to receive the topping layer complete all as specified and as directed.

M&L for preparation of new undecorated surface of wall and applying three coats of white wash on wall.

M&L for 12mm thick expansion joints filled with pre-formed bituminous filler upto a depth/ width of 100mm and top 30mm primed and sealed with sealing compound ,Grade 'A' all as specified and directed

S&F steel work in tubular truss & vertical post of different size bend to shape, cut to length etc, including necessary welding,special shape washer, conforming to IS:1161-1998 grade St-240 complete as directed by Engineer in Charge.

S&F for MS plates as in cleats, base plates, purline etc of Gde Fe-410-W(gde-E-250)

M/L PCC 1:3:6 type C1 20mm grade aggregate as in coping or similar work as directed.

Roughening surfaces of old concconcrete floor by picking sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0kg of cement per sq metre complete all as specified and directed.

M&L for Vitrified parking tiles 30cm x 30 cm x 7 to 10 mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments in floors and over 15 mm thick screed bed in CM 1:4 for laying floor finishes. Make Johnson & equivlent

M&L for PCC 1:2:4 typen B-1 using 20 mm graded stone aggregate as in levling sourse in foor and mass concrete complete all as specific and directed.

Dismantling floor hearth wall tiling incl cement mortar bededing(but not backing) all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm single socketed in any length with rubberring joints laid in trenches or in floors

M&L for reinforced concrete pipes, 300mm dia class NP2, laid and jointed complete with collars all as specifid and diredted.

M&L for concrete bed to drain pipes 300mm dia including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specifida and directed.

S&F rolled sections as in main cress beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or connecting plates cofirming to Fe-410-w (Gde-E250) quality-A

Dismantling asbestos cement corrugated semi corrugated etc sheets in roof covering.

Dismanting timber scantling 40 Sqcm and over in secion in any position in framed work or unframed work

M&L 2nd class HW in scantling fixed clean swan in framed work

Ditto all as per Ser Itme no 92 above but In fillets, rails , posts, rafters and purlins etc under 40 sqcm in section unframed work

Dismanting timber boarding of any description fixed in any position

M&L second class hardwood Weather boarding, 20mm thick, wrought both sides and edges shot and chamfered

S&F Coloured Glazed ceramic tiles 450 x 300 mm x 6 to 7mm thick, in skirting /dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm screeding in Cement mortar 1:4.

Dismantling Structural steel work includings door, gates, etc and similar works complete all as directed

Supply and fixmild steel guard bars to window frame with necessary drilling holes etc including taking out old guard bars from old chowkats all as specified and directed.

Taking down chowkats or frames exc 1.5sqm and not exc 4.0 sqm each with shutters ( without taking off shutters from the frame ) including dismantling of PCC bed blocks for hold fasts.

Taking down chowkats or frames not exc 1.5 sqm each with shutters( without taking off shutters from the frame ) including dismantling of PCC bed blocks for hold fasts.

S&F 35 mm thick 2nd class hard wood Glazed and skelton shutter open rebated and prepared to receive glass, gauze etc (without sash bars) edges of the framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members as specified in SSR Pt I clasue 8.24 (a)

S&F 150mm long aluminium handle, cast type, anodised

S&F Aluminium anodised barrel tower bolts of extruded section 200 mm long and fixed with screws.

S&F MS 200 mm ordinary rat tail rod pattern spring including roller and roller plate

S&F Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

Demolition of reed lathing, single or double including battens and plasters or checken wire lathing

Supply and fix, as in repair,20mm dia curtain rails, mild steel, cromium plated, with fixing brackets, stops, rollers etc all as specified and directed.

M&L complete removal of existing treatment and appplying two coats of weather coat(Apex) over two primer coats of damp shealth to old plastered walls as per manufacturer instrcution including properly fillings the cracks and apllied by approved applicator complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness.

M&L preparing surfaces at wood & wood based materials new or old at any description & girth not otherwise described & treated with tar or coal tar black paint

M&L preparation of old painted steel surfaces over 10cm width or girth and applying one coat of synthetic enamel paint.

Taking down carefully unserviceable point wiring (light,fans,socket etc) complete incl battens and fittings such as switch, ceiling rose,light fittings, regulatos, socket etc and making good disturbed surface of wall/floor etc complete all as specified.

Taking down DB/main switch of any size and making good disturbed surface of wall/floor complete all as specified.

Taking down fans sealing cable ends dismantling blades and removing fan and keeping in safe custody for reuse.

Taking down old U/S Flourescent/LED light fittings any type and size

M & L for point wiring for one light /fan point with 1.5 sqmm cable PVC insulated copper conductor multi stranded as per IS-694 FRLS cable controlled by one way switch, drawn through and including PVC casing caping with all accessories incl 1.5 sqmm multi strand copper conductor cable (green colour) PVC insulated and unsheathed for earth continuity connected to common earth dolly and sunken cast pressed steel terminal box fixed flush to wall of not less than 1.6 mm thick for mounting of fittings such as switch, socket and speed regulator with 3 mm thick Laminated bakelite sheet, PVC Boards (Make' Hylum') cover all as specified and directed.

All as per Ser item No.115 above but for 5 amps socket on same board with other switches

All as per Ser item No.115 above but for 5 amps socket on independent board.

All as per Ser item No.115 above but with 2.5 sqmm cables for 15 amps switch socket combination outlet on independent board complete all as specified and directed.

Supply and fix switch 5 amps switch flush type one way single pole.

Supply and fix switch socket combination outlet flush type, 5 Pin, 5 amps.

Supply and fix Socket outlet 2 in 1, 5 Pin, 5/6 Amps

Supply and fix switch socket combination outlet universal type 5 pin 5/16 amps

Supply and fix ceiling rose surface backelite 65x50 mm having 3 terminals.

S & F stepped type electronic fan regulator 80W flush type on the existing phenolic laminated sheet etc. as reqd. all as specified and directed

S&F PVC angular holder polycarbonate as specified and directed.

Supply & fix Basic all purpose surface and wall mounted LED batten 20 Watt with polycarbonate housing & integrated electronic driver. Cat No LUMILINEBS20WLED865SPCWH Make: Havells

S&F LED ADORE 20 W B22 CDL 3 STAR LAMP Colour Temperature 6500K all as directed

S & F MCB DB Single pole and neutral 8 way Single door with 200 amps rated bus bar complete. Make: Havells/Legrand/L&T/Merlin Gerin/Standard/HPL

S&F MCB SPN 32 Amp, 'C' Series, 10KA braking capacity 230/240 volt AC as specified and directed. Make: Havells/Legrand/L&T/Merlin Gerin/Standard/HPL

S & F MCB SP 6 to 32 Amps 240 volts having 'B' Series complete. Make: Havells/Legrand/L&T/Merlin Gerin/Standard/HPL

Supply and fix New generation energy saving and environmental friendly long life LED street light 25 Watt made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 including GI Pipe 40 mm dia bracket 1.2 mtr in length bent to shape of 120 degree with MS bracket 2 Nos, washers, nuts, bolts etc. Cat Ref : ENDURAPEARLSL25WLED757SASYTOPCMP of Make: Havells

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan including Painting fan blades and fan body, down rod all as directed

M/L for Earthing complete with galvanized steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 meter below normal ground level connected to GI earth lead wire 4 mm dia by means of bolts nuts, check nut and washers of GI and GI tubing 15 mm bore, light grade for earth lead protection up to main earth test point and includingconcrete pit in PCC (1:3:6) typeC 1 pre cast RCC (1:2:4) type B1 cover slab 450 x 450 x 50 mm with one handle for lifting made out of 8 mm dia MS bar, wire mash, 20 mm bore GI tubing(L. G.) for watering ,charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed Electrical plate no 3 of SSR Part-I.

S&F House service bracket (hook type complete with 3.0m long G.I. pipe 40mm dia Med. grade, two nos900 bends. M.S.hook and stay or guy

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor of 2 core x 10 Sq mm, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular. Note 1:-The contract sum shall be arrieved at after deducting amount of schedule of credit from the total quated amount. Note 2-Contractor's supervisor and main worker would wear shirt/T-shirt of colour sky blue/brown/yellow preferable embosed with contractor's firm name while carriying out any activities in defence area for better check of security purpose.

M/S BHAGWATI CONSTRUCTION CO.

Chinmay Traders