PROVN OF TOILET,BATHROOM,URINAL,WHB AT LONGEWALA AND PROVN OF SANITARY BLOCKS,PARKING SHEDS ,ADDITIONAL TOILETS WITH ASSOCIATED EXTERNAL SERVICES AT RAMGARH UNDER GE (AF) STN JAISALMER

Amount

Building Work Ramgarh:- Surface excavation not exc 30 cm and averaging 15 cm deep and getting out in any type of soil complete all as specified and as directed.

Surface dressing n.exc 15 cm deep and getting out any type of soil complete all as specified and as directed.

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m in all type of soil complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone agg as in foundation, filling and mass concrete all as specified and as directed.

M&L for Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

-Ditto- all as per item no.7.00 above but up to 8 mm dia as in stirrups, rings spacers and binder complete all as specified and as directed.

-Ditto- all as per item no.7.00 above but up 6 to 8 mm dia as in stirrups, rings spacers and binder complete all as specified and as directed.

M&L for RCC M-25 design mix (20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete.

M&L for hard core of gauge n. exc 63mm broken stone or boulders, deposited, spread and levelled in layers n. exc 15cm thick watered and rammed to a true surfaces all as specified and directed.

M&L for 1:4:8 type D2 (40mm graded stone aggrage) cement concrete 75 mm thick including finishing concrete surface even & smooth w/o using extra cement in as in floors/sub base etc complete all as specified and as directed.

M&L for rendering 10mm thick on stone / concrete block masonry surfaces of any description in cement mortar (1:6) is to be finished even and smooth (without using extra lime or cement) complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on stone / concrete block masonry surfaces other than fair faces of concrete / brick is to be finished even and smooth (without using extra lime or cement) complete all as specified and as directed.

M&L for preparation of newly plastered of wall surfaces and applying two coat of oil emulsion distemper over a coat of alkali resistant priming paint as approved complete all as specified and as directed.

M&L for preparation of new surface on wall/roof surface and applying two coat of exterior emulsion paint (weather coat) 1st quality as in different tint / camouflage pattern as directed at any height of the bldg/structure complete all as specified and as directed.

S&F for Brass tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S&F for Steel work in tubular pipes stanchions, purlins including special shaped , including special shaped washer etc. complete using or including butt welded tuber cum forming to I.S. 1161-1979 grade st - 240 complete all as specified and as directed.

M&L Pre-painted Galvanised, corrugated mild steel sheeting 0.63 mm thick with two corrugations side lap,fixed with J hook and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and as directed.

M&L for non skid coloured ceramic tiles 7-8mm thick (square or rectingular)area of each tile not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 etc complete all as specified and as directed.

M&L for glazed coloured ceramic tiles in vertical surfaces 450X350X7 mm/350X250X7 mm /300X450X7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick rendering in CM 1:4 on other then fair faces of brick work etc complete all as specified and as directed.

M&L for PCC (1:3:6) type C-1 with using 20mm graded stone aggregated as in cill, step and for inserting hold fast of doors and windows complete all as specified and as directed.

M&L for 20mm thick granite ( of any type) slabs/Tiles laid in floors/treads over 15mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white cement with admixture of pigment to match the shade of granite complete all as specified and as directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) finished even and smooth without using extra cement as in plinth protection, paths , steps etc complete all as specified and as directed.

S&F for 30mm thick flush shutters factory made solid core construction with block boards core and plywood face panels, commercial type on both sides (ISI marked) fixed to chowkhats complete all as specified and directed.

S&F for wood grain printed 1mm PVC sheet fixed or laid on face of flush doors by using rubber based adhesive, supplying & fixing at site complete all as specified and as directed.

S&F for Framed work as in doors or gates of angle or other section with gusset plates,rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooksn and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing Fe-410 W (Gde E-250 Quality B) complete all as specified and as directed.

S&F for MS hold fast and similar article conforming to Fe-290 Gde-E-165-0 or Fe-310-0 complete all as specified and as directed.

S&F for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube 19mmx19mm x19mm gauge & PDM rubber gasket wealther seal to be provided through out the frame. The profile shall be mitre cut at two corners and jointed by inserting 02 Nos of 150mm long brackets of 15x15mmx15 gaughe MS square tube inside the 19mmx15mm MS square tube and suitably screwed complete all as specified and as directed.

S&F for factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes 19mmx19mmx19gauge for stiles & 15mmx15mmx19 gauge for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC C channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail and bottom rail on either side & as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading & joined together with solvent cement etc complete all as specified and as directed.

S&F for anodized aluminium partition or frame for door, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F for anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

S&F for 4mm thick sheet glass ordinary quality and glazing with clips in square n exc 0.5 Sqm in each pane complete all as specified and directed.

S&F for aluminum anodized barrel tower bolt of extruded section size of bolt 150mm complete all as specified and as directed.

S&F for 100 mm long stainless steel Butt hinges complete all as specified and as directed.

S&F for aluminum handle cast type anodized 125mm size complete all as specified and directed.

S&F for peg set 6 (Zinc) Prayag or equivalent as directed by Engineer -in - Charge.

S&F for aluminium alloy, anodised sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S&F for aluminium alloy, anodised, 250mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded msections or cast-aluminium alloy and fixed complete all as specified and as directed.

M&L for preparation of new steel surface of any description over 10 cm in width or girth not other wise described and applying two coat of synthetic enemal paint over one coat of red oxide primer complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) pipes single socketed in any lenghts with rubber vring joints, laid in trenches or in floors etc complete all as specified and as directed.

-Ditto- all as per Item no 40.00 above but fixed to walls complete all as specified and as directed.

S&F for 110mm bore PVC (SWR) pipes single socketed in any lenghts with rubber vring joints, laid in trenches or in floors etc complete all as specified and as directed.

-Ditto all as per Item no 42.00 above but fixed to walls complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) bends any radius etc complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) bends any radius provided with access door etc complete all as specified and as directed.

S&F for 110mm bore PVC (SWR) bends any radius etc complete all as specified and as directed.

S&F for 110mm bore PVC (SWR) junction single(Single T) equal or unequal provided with access door etc complete all as specified and as directed.

S&F for 110mm bore PVC (SWR) vent cowl etc complete all as specified and as directed.

S&F for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F for 1000 ltrs capacity rotational moulded polyethylene water storage triple layer white tanks (cylindrical verticle with closed top) hoisted and fixed in position complete all as specified and as directed.

S&F for 20 mm dia ball valve ,high pressure of PTMT with epoxy coated, aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minium wt-210 gms) complete all as specified and as directed.

S&F for 15mm bore of tube steel water tubing medium grade galvanized with all fittings and fixtures fixed complete to walls, ceilings or laid on floors etc complete all as specified and as directed.

S&F for 20mm bore of tube steel water tubing medium grade galvanized with all fittings and fixtures fixed complete to walls, ceilings or laid on floors etc complete all as specified and as directed.

S&F for 25mm bore gate valve complete all as specified and as directed.

S&F for 15mm bore fancy type premium quality chromium plated stop cock cast copper alloy, screwed doen, high pressure, screwed bith ends for iron pipe or for unions, complete all as specified and as directed.

S&F for 15mm bore fancy premium quality type chromium plated bib taps cast copper alloy with crutch or butterfly handle, screwed down etc complete all as specified and as directed.

S&F for 75mm diameter of outlet PVC (SWR) floor trap, plain with grating including jointing with solvent cement & jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc complete all as specified and as directed.

S&F for vitreous China wash basin white flat back size 550 x 400mm including 40x40x5mm angle iron brackets with paint including cutting for and pinning in ends of brackets , CP pillar tap fancy type copper alloy wiith capsten handil scrubbed down high pressure screbbed shanks and fly nuts screwed for iron pipe15mm dia, PVC conection 450mm long with PTMT nuts high presure , brass PTMT waste coupling 32 mm dia with long dcrewrd shanks and fly nuts etc complete all as specified and as directed.

S&F for Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) with 40mm size brass chromium plated waste coupling with long screwed shanks and fly nuts flange end bedded in red lead complete all as specified and as directed.

S&F for urinal spreader of CP any colour for fixing with 15 mm dia pipe complete all as specified and as directed.

S&F for vitreous china sqatting pan "orissa" pattern of size 580x440mm white with integral foot rests, P or S trap etc complete all as specified and as directed.

S&F for 32mm bore of pipe low density polythylene pipes (LDPE) with fittings as required of pressure rating 6 kgf/cm2 and fixed complete to walls, ceilings or in floors etc complete all as specified and as directed.

S&F for 40mm bore of pipe low density polythylene pipes (LDPE) with fittings as required of pressure rating 6 kgf/cm2 and fixed complete to walls, ceilings or in floors etc complete all as specified and as directed.

S&F for 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets & PVC conection 450mm long with PTMT nuts high presure complete all as specified and directed.

S&F for PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F for soap dish any type, fixed to plugs with chromium plated brass screws prayag or equivalent complete all as specified and as directed.

Building Work Longewala:- Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in any type of soil complete all as specified and as directed.

-Ditto- all as per Item no-68.00 above but depth above 1.50m to 3.00 m complete all as specified and as directed.

Returning , filling in including in spreading ,leveling,watering and well ramming in layers.n exc 25 cm complete all as specified and as directed.

Removing excavated material soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work, flat and rough finished surfaces of concrete; vertical or to batter complete all as specified and as directed.

M&L for Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted & gap filled with in cement mortar 1:2 complete all as specified and as directed.

S&F for Plate girder or single stanchions,built up of one beam or channel section with flange plates, caps,bases. splices, angle brackets,cleats and other connections complete all as specified by Engineer-in-Charge.

M&L for square rubble walling Jodhpur type brought up to courses well bonded, bedded and solidly hearted in cement morgtar 1:6 etc complete all as specified and as directed.

Labour only for hammer dressing to face stones with maximum depressions on face from a stright edge not exc. 20 mm and dressing face beds and joints as specified to SR walling Jodhpur type brought upto courses complete all as specified and as directed.

M&L for precast cement concrete (1:3:6) type C1 (20mm graded stone aggregate) solid block masonary exc 10 cm in width and set in CM (1:6) complete all as specified and as directed.

M&L for 10mm thick internal plaster in CM (1:6) on fair faces of brickwork or concrete surfaces finished even and smooth (without using extra cement) with 3mm thick wall care putty complete all as specified and as directed.

M&L for prepration of new surface plastered or unplastered applying two coats of White washing on walls complete all as specified and as directed.

M&L for prepration of unplastered applying two coats of White washing on ceiling,soffits of chajjas/drop & roof projection facia etc complete all as specified and as directed.

M&L for preparation of newly plastered external wall surfaces and applying two coats of cement paint of approved tint over alkali resistant primer complete all as specified and as directed.

S&F for aluminium alloy, anodised sliding door bolt 200mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S&F for 100mm size butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and as directed.

S&F for 25mm size anodised extruded aluminium alloy handle fabricated type complete all as specified and as directed.

S&F for 15mm bore cast copper alloy, with capstan heads, chromium plated pillar taps with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down for iron pipes etc complete all as specified and as directed.

S&F for 15mm size cast copper alloy, chromium plated stop,angle valves screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipes etc complete all as specified and as directed.

S&F for white coloured vitreous china wash down water closet pan (Pedestal pattern) with and including plastic water closet seat closed pattern with flat bottom and cover, jet and mild steel chromium plated or aluminium hinging device fixed incl P or S trap complete all as specified and as directed.

S&F for white coloured vitreous china urinal half stall type with 32mm size brass chromium plated waste coupling with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F for swivel shower rose of PTMT any colour for 15 mm bore pipe( min wt 40gm) complete all as specified and as directed.

S&F for shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and as directed.

S&F for liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete all as specified and as directed.

M&L for rendering 10 mm thick in CM 1:4 with water proofing compound over green concrete surface (WPC will be measured & paid seperately) surface finished even and smooth (without using extra lime or cement) complete all as specified and directed by Engineer-in-Charge.

Supply only Water proofing compound @3% by wt of cement etc complete all as specified and as directed.

M&L for 50mm thick PCC type B-0, 1:2:4 (12.5mm graded aggregate) as in floor Finishing surface even and smooth without using extra cement complete all as specified and as directed.

S&F for Granite partition of 25 mm thick for partition of urnial etc complete all as specified and as directed.

S&F for 20mm bore ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F for 15mm bore cast copper alloy, chromium plated bib taps with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed as approved complete all as specified and as directed.

S&F for PVC (SWR) 110 mm dia pipes single socketed in any length with rubber ring joints fixed to walls with suitable fixtures complete all as specified and as directed.

S&F for PVC (SWR) 75 mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F for PVC (SWR) bends any radius 75 mm dia complete all as specified and as directed.

S&F for PVC (SWR) bends any radius 110 mm dia complete all as specified and as directed.

M&L for broken stone or boulders hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 75mm thick cement concrete type C-2 1:3:6 using 40 mm graded stone aggregate as in for plinth protection complete all as specified and as directed.

Building Work (Parking Sheds):- Excavating in post holes (or similar holes) each in exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm in any type of soil complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B-2 as in foundation (post hole), filling & mass concrete complete all as specified and as directed.

S&F for Mild steel Rolled sections as in column, vertical posts, main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc. conforming to Gde E-250 (Fe- 410-W) quality 'A' complete all as specified and directed.

S&F for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ 'J' hooks complete all as specified and directed.

S&F for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts complete all as specified and as directed.

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone agg as in sub-base including formwork etc complete all as specified and as directed.

M&L for 100mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate as in bearing surface including formwork etc complete all as specified and as directed.

M&L for 30mm thick Wearproof granolithic metallic hardner concrete as specified in manufacturer instructions (included metallic hardner) and acomplete all as specified and as directed by Engineer -in- Charge.

M&L for Finishing surface of concrete roads, pavements, by brooming complete all as specified and as directed.

M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade `B' complete all as specified and as directed.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade `B' complete all as specified and as directed.

Sewage Disposal:- Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth in foundation and getting out in soft /disintegrated rock complete all as specified and as directed.

-Ditto- all as per item no-115.00 above but exc 1.5m in depth but n exc 3.0m depth complete all as specified and as directed.

-Ditto- all as per item no-115.00 above but exc 3.0m in depth but n exc 4.5m depth complete all as specified and as directed.

M&L for Brickwork with sub-class 'B' bricks straight or curved on plan exceeding 6m mean radius built in in CM 1:4 complete all as specified and as directed.

M&L for Brickwork with sub-class 'B' bricks in one brick thick honey comb walling built in in CM 1:4 complete all as specified and as directed.

M&L for Brickwork with sub-class 'B' bricks in one and half (1 and 1/2 ) brick thick honey comb walling built in in CM 1:4 complete all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:6.on stone masonry surface other than fair faces of brick work or on one side of lathing etc complete all as specified and as directed.

M&L for PCC 1:3:6 type C1, using 20mm graded aggregates as in copings including weathering, slightly rounded or chamfered angles and throating and necessary form work and finishing the top surface of concrete even and smooth without using extra cement complete all as specified and as directed.

M&L for providing pre-cast cement concrete type - B-1 1:2:4 (20 mm stone agg) in landings cover slab (for manhole etc) with and including formwork as required and set in cm 1:6 etc complete all as specified and as directed.

M&L for Pre-cast cement concrete block (Type C-1, 1:3:6 (20mm graded aggregate))masonry with solid blocks set in cement mortar 1:6, exc. 10 cm in width and setting in mortar, complete all as specified and as directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L for RCC type B-1 (20mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for Form work to well steining and well curbs rough finished flat surfaces circular on plan complete all as specified and as directed.

M&L for PCC 1:2:4 Type-B-l (20 mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles andthroating, as directed complete all as specified and as directed..

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:3 for finished even and smooth without using extra complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:3 for finished even and smooth without using extra cement complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate ) in surface channels, drains and benching for main hole and finishing of exposed surface of concrete complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate for 150 mm dia bore drain pipe for bed concrete including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and as directed.

S&F for 150 mm bore salt glazed stone ware grade "A" drain pipes laid in trenches and jointed complete all as specified and as directed.

Removing excavated soil to a distance exceeding 50m but not exceeding 250m and depositing where directed, at a level not exceeding 1.5 M above from starting point etc complete all as specified and as directed.

M&L for 150 mm Reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and as directed.

M&L for precast RCC (1:2:4) type B1 (20 mm graded stone aggregate) as in manhole cover slab in CM 1:4 including use and waste of formwork as required

M&L for RCC Septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls , Base Slab , Baffle walls and Roof Slab including beams etc with Vent shaft , manhole openings with cover connection etc conventional type complete with effective depth of 1.5 meter and overall depth of 3 meter for 50 Users complete all as specified and as directed. Note:-This item will be excute as per TD Drawing.

M&L for Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 3.6 dia X 4.5 m effective depth complete all as specified and as directed. Note:-This item will be excute as per TD Drawing.

Internal Electrification:- M&L for point wiring for controlled by one switch with PVC insulated but unsheathed single core FRLSH multistranded copper conductor cable IS-694 marked of size 1.5 Sqmm (nominal area) in and including non metallic rigid PVC conduit 20 mm dia by cutting chases in walls by cutter and making good the surface in CM 1:3 and to the original specification and PVC conduit on ceiling for steel structure/surface conduit with clamps, gutties etc for RCC ceiling with including one run of PVC insulated FRLSH copper conductor cable of 1.5 Sqmm with green insulation as earth wire and connected to earth dolly complete all as specified and as directed. (a) One light point controlled by one, one way switch

(b) -Ditto- same as above item no.139 above but one socket outlet 3 Pin, 6 Amp on same board complete all as specified and as directed.

M&L for point wiring for controlled by one switch with PVC unsheathed single core multistranded copper conductor cable of size 4 Sqmm (nominal area) in and including PVC conduit 20 mm dia by cutting chases in walls by cutter and making good the surface in CM 1:3 and to the original specification and PVC conduit on ceiling for steel structure/surface conduit with clamps, gutties etc for RCC ceiling including one run of PVC insulated FRLS copper conductor cable of 4 Sqmm with green insulation as earth dolly for 6 pin, 16 Amp socket outlet on Independent board complete all as specified and as directed.

S&F for switch piano flush type single pole one way 5 Amp (ISI Marked) complete all as specified and as directed.

S&F for switch piano flush type single pole one way 15 Amp (ISI Marked) complete all as specified and as directed.

S&F for socket out let 2 in 1, 3 pin 5 Amp flush type (ISI Marked) complete all as specified and as directed.

S&F for socket out let 2 in 1, 3 pin 15 Amp flush type (ISI Marked) complete all as specified and as directed.

M&L for ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC/Polycarbonate,isolated body (ISI Marked) complete all as specified and as directed.

M&L for submain wiring with 2 single core PVC insulated unsheathed multi stranded copper conductor FRLS wire 4.00 Sq mm 1100 volts grade including and 4.00 Sq mm PVC insulated, multi stranded, unsheathed copper wire green in colour as earthing lead drawn through in PVC conduit complete all as specified and as directed. Note :- Two run of 4.0 Sqmm cable and one run of 4.0 Sqmm cable as earth continuity conductor and 25 mm PVC conduit shall be measured & paid as one unit.

M&L for Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amp complete all as specified and as directed.

S&F for MCB, 6 to 32 Amp, SP, 240 Volt. complete all as specified and as directed by Engineer-in-Charge.

S&F for MCB, 32 Amp, SPN, 240 Volt complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing Surface and wall mounted LED tube light fittings of cap 10W , two feet Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver complete all as specified and as directed.

Supply and fixing LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp, GI pipe bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

S&F for Prewired Distribution Board factory made sheet metal enclosure double door distribution board class IP-43 IK 09 with 200 Amp rated copper bus bar 240 Volts 8 way (2 + 6 way) single pole and neutral complete all as specified and as directed.

S&F for exhaust fan made out of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of size 250mm sweep complete all as specified and as directed.

S&F for electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and as directed by Engineer-in-Charge.

M&L for Hot water gun metal glove valve/safety valve 15mm bore complete all as specified and as directed by Engineer-in-Charge.

M&L for Hot water tap of brass/gun metal 15mm bore complete all as specified and as directed by Engineer-in-Charge.

S&F for hot water PVC connections length 450mm for geysers including necessary clamps, nuts and bolts etc. complete all as specified and as directed.

S&F for MCB, 40 to 63 Amp, SPN, 240 Volt complete all as specified and as directed.

S&F for MCB, 6 to 32 Amp, SPN, 240 Volt complete all as specified and as directed.

S&F for Metal clad box including 20 Amp MCB SPN complete all as specified and as directed.

M&L for point wiring with PVC insulated unsheathed 1100 Volts grade single core multistranded copper conductor cable 1.5 Sqmm drawn and including PVC casing capping and accessories, fixed on wall/ceiling etc with necessary fixing accessories and earth continuity conductor cable of size 1.5Sqmm green colour connected to common earth and earth dolly including cast iron/pressed steel terminal/wooden boxes (as per site requirement) Covered with laminated sheet top cover swiches/sockets/ fan regulators fixed with cadmium plated machine screws all as specified for the following: (a) One light point controlled by one way switch

(b) -Ditto- all as per item no-162.00 above but One fan point controlled by one way switch complete all as specified and as directed.

(c) -Ditto- all as per item no-162.00 above but One socket outlet 5 Amps on independent board complete all as specified and as directed.

(d) -Ditto- all as per item no-162.00 above but One socket outlet 5 Amps on the same board complete all as specified and as directed.

M&L for point wiring for controlled by one switch with PVC unsheathed single core multistranded copper conductor cable of size 4 Sqmm (nominal area) in and including PVC conduit 20mm dia by cutting chases in walls by cutter and making good the surface in CM 1:3 and to the original specification and PVC conduit on ceiling for steel structure/surface conduit with clamps, gutties etc for RCC ceiling including one run of PVC insulated FRLS copper conductor cable of 4 Sqmm with green insulation as earth dolly for 6 pin, 16 Amp socket outlet on independent board , including cast iron/pressed steel terminal/ wooden boxes (as per site requirement) covered with laminated sheet top cover switches/ sockets/ fan regulators fixed with cadmium plated machine screws complete all as specified and as directed.

S&F for switch single pole one way 16 Amp (ISI Marked) complete all as specified and as directed.

S&F for socket out let 2 in 1, 2/3 pin 6 and 16 Amp (ISI Marked) complete all as specified and as directed.

S&F for exhaust fan, steel body, AC single phase 230V of size 300mm sweep with blades and frames and louvers including making holes in to the wall as per fan size and making good the disturbed surfaces complete all as specified and as directed by Engineer-in-Charge.

External Electrification:- Supply, laying and testing cable XLPE insulated screened PVC beded galvanized steel strip or wire armoured electric power cable (H/duty) with stranded Al conductor 1100 volt grade of size 2 core 10 Sqmm laid in trenche/crossing the road/fixed on pole complete all as specified and as directed.

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth and getting out in soft and loose soil complete all as specified and as directed.

M&L for Dry tibba sand cushnioning to underground cable provided with a layer of 8cm deep before laying cable and 15cm after laying of cable and punned to 18cm after laying of cable and cover for protection of underground cable complete all as specified and as directed. Notes :- (i) Approved dry sand free from vegetation, grass and other deterious substances shall be used. (ii) For the purpose of payment only punned thickness shall be measured for payment purpose.

M&L for Stone patti 40 to 50mm thick rough dressed Jodhpur stone slab cover in trenches for protection of cable 25 to 35cm wide and not less than 60cm in length laid dry abutting each other with gap between adjacent slab not exceeding 10mm over sand cushioning complete all as specified and as directed.

M&L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick surrounded with charcoal and salt, buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as specified and as directed. (i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) Item includes the cost of 7.50m GI pipe for protection of earth wire/strip Any variation in length shall be adjusted through deviation order. (iii) Item includes cost of 7.50m earth lead wire/strip. Any variation in length shall be adjusted through deviation order. (iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate.

External Water Supply:- M&L for cutting of existing DI/GI pipe of size upto 80mm dia and making arrangement for insertion of new Tee, Gaskets, Nut bolts, Rubber rings etc. all as directed including necessary excavation & earth work as required of 80mm dia of sizes complete all as specified and as directed.

Supply and lay pipe galvanized, “Medium class”, including fittings 50 mm dia complete all as specified and as directed.

Supply and lay pipe galvanized, “Medium class”, including fittings 25 mm dia complete all as specified and as directed.

S&F for 20 mm new gun metal Globe/Gate valve,screwed down high pressure with iron wheel head screwed both ends for GI pipe including all fittings/fixture like nipple,union etc complete including taking down the old unserviceable Globe/Gate Valve for following sizes complete all as specified and as directed.

S&F for 25 mm dia Foot Valve confirming to IS 4038 complete all as specified and as directed.

Supply,connect,testing and commissioning energy efficient Monoblock pump set,electric driven 230 Volt SP of capacity not less than 1 HP discharge SUCxDEL,25 x 25 with head range 9-14 m and discharge range 90-50 LPH ,including complete PCC foundation nut bolts, Shed for Monoblock Pump complete all as specified and as directed.Make:-Kirloskar,CG or equivalent.

M&L for Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of size 50mm dia complete all as specified and as directed.

M&L for Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of size 25mm dia complete all as specified and as directed.

Excavating in over areas exc 1.50 m deep and nexc 3m and getting out any type of soil complete all as specified and as directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, flat and fair finished surfaces of concrete not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L for reinforced cement concrete (design mix) M-30 (20mm graded aggregates) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like as directed.

M&L for reinforced cement concrete (design mix) M-30 (20mm graded aggregates) in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc. basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for reinforced cement concrete (design mix) M-30 (20mm graded aggregates) in wall and the like complete all as specified and as directed.

Form work to faces of curved walls and simiar work etc complete all as specified and as directed.

M&L for 10mm thick internal plaster in CM (1:4) on fair faces of brickwork or concrete surfaces finished even and smooth (without using extra cement) including labour for WPC complete all as specified and as directed.

M&L for 10mm thick internal plaster in CM (1:3) on fair faces of brickwork or concrete surfaces finished even and smooth (without using extra cement) including labour for WPC complete all as specified and as directed.

Removing excavated material soil n exc. 250m but not exc. 500 mand depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Road,Path & Culvert:- M&L for Factory made rubber moulded precast concret interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with mixture of grey and white cement and pigment ,complete all as specified and as directed.

M&L for Sand filling under floors or in foundatins including watering and consolidation,complete all as specified and as directed.

M&L for Cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone agg) as in coping,benching including weathering slightly rounded or chamfered angles as directed including necessary formwork and finishing the exposed surface,complete all as specified and as directed.

KHUSBU CONSTRUCTION COMPANY (BID ID -3198208)

BHAGWATI CONSTRUCTION (BID ID -3202032)