CWE/Y-23/2021-22

Amount

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in hard and dense soil, complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in hard rock, complete all as specified and directed.

Excavation over areas, n.exc 1.5 m deep and getting out in hard rock complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25Cm, complete all as specified and directed.

Removing excavated materials/ soils, not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed.

Earth filling under floors or pavings laid in layers not.exceeding 25cm thick, spread, leveled and rammed including watering complete all as specified and directed

Hard core of broken stone or boulders of gauge not exc 63 mm deposited ,spread and leveled in layer not exc 15 cm thick complete all as specified and directed.

PCC 1:3:6 (nominal mix) type C-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

PCC 1:2:4 (nominal mix) type B-2 (using 40mm graded crushed stone aggregates) as in surface channel and drains complete all as specified and directed.

RCC M-25 (Design mix) type A-1 (using 20 mm graded crushed stone aggregates) as in beams, cantilevers and like complete all as specified and directed.

Concrete bed to drain pipe of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) complete all as specified and directed. Note :- Thickness of bed and width of bed shall be provided all as per preamble a (i) & a (ii) on Srl page no 356 of SSR Part-II Rates (2010).

Reinforced concrete pipes, class NP2, laid & jointed complete with collars, bore of pipe 200mm, complete all as specified & directed.

Bends, laid and jointed complete for 150mm dia pipe complete all as specified and directed

Precast cement concrete as in landing, cover slabs (for manhole etc) and similar articles with precast cement concrete Type B-1, 1:2:4 (20mm graded crushed stone aggregate) and setting in cement mortar 1:4 complete all as directed.

Use & waste of form work to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc alo splays between floors and beamsfor rough finished surfaces of concrete, complete all as specified & directed.

Use & waste of form work to sides of square, circular rectangular or polygonal pillars, posts, struts, piers, columns, beams and stanchions for rough finished surfaces of concrete, complete all as specified & directed.

Walling of random rubble stone masonry, brought upto course, well bonded, bedded and soilidly hearted, built in CM 1:6, complete all as specified and directed.

Brick work with old size fly ash bricks, class 7.5, straight or curved on plan exc. 6 metre mean radius built in cement mortar 1:4 all as specified & directed.

Brick work with old size fly ash bricks, class 7.5, straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified & directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelam PVC sheet and edges will be painted to match with prelam sheet, reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2010 Part-II compete all as specified and directed.

Factory made solid PVC moulded door shutter 28mm - 30mm thick (stiles) with particle board core with 2,4,or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face complete all as specified and directed.

Factory made solid panel PVC ventilator shutter (fully glazed) 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails.M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Pane of 4 mm thick sheet glass to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, complete all as specified and directed.

Aluminium handles cast type anodized of size 150 mm complete all as specified and directed.

Aluminium handles cast type anodized of size 100 mm complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section of size 100 mm and fixed complete all as specified and directed.

Mild steel butt hinges of size 100mm medium weight cold rolled complete all as specified and directed.

Mild steel butt hinges of size 75mm medium weight cold rolled complete all as specified and directed.

250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

3 mm thick, figured glass pin head type and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed.

0.63 mm thick, galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with with L-type or J-type or cranked hook bolts , in roofs, walls etc. with grade of zinc coating 275 gms per sqm complete all as specified and directed.

0.80 mm thick, galvanised, plain mild steel sheeting as in ridges, hipe, valley gutters, drip and straight flashing (length and girth as fixed) with grade of zinc coating 275 gms per sqm complete all as specified and directed.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed.

Rolled mild steel work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed.

Mild steel work as in hold fast, wind ties for roof including securing bolts including all necessary drilling ,bolting or reverting etc and all similar work conforming to Fe-290 (Gde E-165) complete all as specified and directed.

Mild steel framed work as in brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. not exceeding 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

75mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregates) as in sub base complete all as specified and directed. .

100 mm thick, PCC 1:2:4, type B-2 (using 40 mm graded crushed stone aggregates) as in floor finish, surface finished even and smooth without using extra cement complete all as specified and directed.

Plain cement concrete 1:3:6, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Chequered cement concrete coloured tiles, homogenious texture glossy finished , chemically coated machine pressed 30 cm x 30cm x 25mm thick set, jointed and pointed in near cement slurry in floor with gray cement and pigment and including 20 mm thick cement screed in cement mortar 1:4 over and including 75mm thick PCC 1:3:6 (Nominal Mix) type C-2, using 40mm graded crushed stone aggregate complete all as specified and directed. Shade/Colour of tile shall be approved by the GE.

Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

Glazed ceramic coloured tiles of size 300mm x 200 mm x 7 mm thick as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the GE.

Rendering cement plaster 15mm thick in cement mortar 1:6 on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:4 on stone masonry or surface other than fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Preparation of steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil-emulsion over a coat of alkali-resistant priming paint complete all as specified and directed.

Preparation of newly plastered or un plastered, previously undecorated wall surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

G I tubing medium grade of 15 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor/trenches complete all as specified and directed.

GI tubing medium grade of 20 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor /trenches complete all as specified and directed.

GI tubing medium grade of 25mm bore with all fittings and fixtures laid in trenches complete all as specified and directed.

Cutting chases in walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good complete all as specified.

Brass chromium plated tubular towel rail 20 mm dia, "D" type, 60 cms long between flanges with and including chromium plated brass brackets, brass screws complete all as specified

Chromium plated soap dish, fixed in repair complete all as specified.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Chromium plated shower roses with or without swivel joints, 125mm size, including fixing to steel pipe or union complete all as specified

Wash basins, Vitreous China (Flat white type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete all as specified. Make: Cat Part No. 1008 of Cera or equivalent in makes mentioned in Appx

Stop valves/ angle valve/ concealed valve, cast copper alloy, chromium plated, fancy type, screwed down, high pressure , screwed both ends for 15mm bore iron pipe or for unions and complete, all as specified. Type of valve approved by the GE.

Stop valves cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15mm bore iron pipe or for unions complete, all as specified.

Stop valves cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 20mm bore iron pipe or for unions complete, all as specified.

Bib tap, cast copper alloy ,chromium plated, fancy type , screwed for iron pipe or for brass ferrule of 15 mm bore complete all as specified and directed.

25 mm dia, gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Drilling and tapping of GI pipe water mains 40mm in position for branch connection of 25 mm dia bore including provision of clamps , nut bolts and all conecting accesseriose complete, all as directed.

PVC connections 15 mm size with PTMT nuts of length 600mm fixed in repair complete all as specified and directed.

PVC valve less, crystal white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, all as specified. Make: Cat Part No. 2602 of Cera or equivalent in makes mentioned in Appx .

600x450 mm bevelled edge mirror of slected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screwed and cup washers.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate complete all as specified, incl making connections to trap and to flush pipe, etc all as specified. Make: Cat Part No. 2071 of 'Cera' or equivalent makes mentioned in Appx.

Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (including fixing bolts, flush pipe, PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, capacity 5.0 litres), with grating and union for discharge pipe, flush pipe and waste pipe, Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe, complete all as specified and as directed.

110mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to tranches or in floor or walls complete all as specified and directed.

75mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to tranches or in floor or walls complete all as specified and directed.

110 mm dia PVC(SWR) bend, any radius complete all as specified and directed.

75 mm dia PVC(SWR) bend, any radius complete all as specified and directed.

110 mm dia PVC (SWR) reducers complete all as specified and directed.

75 mm dia PVC (SWR) vent cowl complete all as specified and directed.

125/110mm dia PVC (SWR) 'S' trap complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

110mm dia PVC (SWR) junction single, (single T) equal or unequal provided with oval access door complete all as specified and directed.

Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed.

75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified.

Rotational moulded polyethylene water storage tank 1000 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete all as specified.

Septic tank for 50 user (RCC Construction) designed to carry sewage and sludge water, excavation in any type of soil, PCC 1:4:8 in foundation, RCC M-25 Design Mix in walls, base slab, Baffle walls and roof slab including beams etc with vent shaft, manhole openings with cover connection etc, complete with effective depth of 1.5 M and overall depth of 3.00 M all as shown on drawing and as specified.

Construction of soakage well 1.20 meter internal dia x 3.00 meter effective depth including earth work in hard rock cum hard soil, foundation in PCC 1:3:6, fly ash brick wall walls of honey combed with top ring of M-25 (Design Mix) using 20mm graded crushed stone aggregate concrete, form work, reinforcement including intercepting chamber and screen chamber made of brick masonary in CM (1:4) , RCC cover slab in M25/SFRC cover, interconnecting pipes of RCC/DWC/cast iron pipes, bends and fittings. Complete, filled with brick bats complete all as shown on drgs,specified and directed .

Point wiring with 1.5 Sqmm copper conductor FRLS (Multistrand) PVC insulated ISI Marked unsheathed cable in and including PVC conduit not less than 20mm dia, medium grade with IS 9537 (Part-III) 1983 marking with all fittings/ accessories as specified in preamble 1 (a) to (q) of Section 19 of SSR Part-II, under heading point wiring and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as earth wire (green colour) connected to common earth dolly and including pressed steel terminal boxes made out of 1.20 mm thick mild steel sheet duly painted with one coat of red oxide primer for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) concealed in wall or surfaces of wall for one light point or one fan point or one fan point through regulator or one bell point, controlled by one way switch/ push button complete all as specified and directed.

All as per serial item No. '83' above but for 3 pin 15 Amps socket out let independent with 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Switch piano flush type, single pole, one way, 5 Amps, all as specified.

Switch piano flush type, single pole, one way, 15 Amps, all as specified.

Socket outlet, 2 in 1, 5 Pin, 5/15 Amp ,flush type, multipurpose, complete all as specified.

Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified.

Exhaust fan, 300 mm sweep, 1400 RPM, 230 Volts, AC, 50 Hz, single phase, non metallic type complete with louvers , fixing arrangement in any condition and making connections with suitable capacity copper twin core conductor and ceiling rose, complete all as specified and directed.

Electric geyser (Water storage heater), 25 Ltrs, 5 star rated, including two nos of 400mm long hot and cold PVC connection including grouting of nuts, bolts & washer on wall and making good the disturbed surface including plaster work complete all as directed. Make: Havells Cat Part No GHWAMGSIB025 or equivalent in BAJAJ/CROMPTON GREAVES/ JAGUAR/USHA LEXUS/MORPHY RICHARDS

Universal batten for LED tube light fitting suitable for indoor applications type , 4 feet, alongwith 18 Watts LED tube rod complete with all accessories and fixtures prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete. Make : Havell's Cat Part No. REGALBATTENT5UPTO01X18WDSBSWH & LHLDDAXEUL8Z018 or equivalent in makes mentioned PS.

10 Watts, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack, complete with all accessories and fixtures prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete. Make : Havell's Cat Part No.LHEXACP7IN1W010 or equivalent in makes mentioned PS.

MCB SPN 40 Amp, 240 Volts, 10 KA all as specified.

MCB SP 6 to 32 Amp, 240 Volts, 10 KA all as specified.

Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 8 way, double door, 240 volts with 200 Amp rated bus bar completed all as specified.

LED 30 W, Energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP66 protection and Impact resistance of IK07 complete fixed on pole/ wall with and including bracket made out of galvanised iron pipe 40mm dia, medium grade of length 1.50 metres with two clamps made out of mild steel flat 25x4 mm with nuts, bolts and washers complete accesseries including two coats of aluminium paint after preparation of surfaces including making connection with aluminium PVC insulated copper wire 2.5 sqmm as required at site and connecting the same to the cable with the help of the connector all as specfied and directed . Make:- Havells Cat Part No LHEWEBP7PL6S030 or equivalent in makes mentioned in PS.

Sand cushioning to under ground cables provided with a layer of sand 8 cms thick before laying the cable and 15 cms thick after laying the cable complete all as specified and directed.

Sub class "B" bricks for covering to cable laid dry flat, with width equal to length of bricks all as specified and directed.

GI pipe light grade of size 40 mm dia laid in trenches/ walls including clamps, screws etc, complete all as specified and directed.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 16 Sqmm, 3 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC M-15, type B-I using 20mm graded crushed stone aggregates with 40mm thick precast cover of size 550 mm X 550 mm X 75 mm of RCC (1:2:4), type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

Mahashakti Enterprises

M/s Thakur Engineers

VIJAY KUMAR LAKHNI

M/S RUDHRAKSH TRADING CO