5-LT Reconductoring at gramadeepam

Reconductoring LT line

Dismantling (without damage) one km LT 3ph 4 wire OH line, cross arms, insulators and stacking the conductors in rolls.

Insertion of one HT A type pole in existing line incl. digging & backfilling pit, fitting cross arm, insulators, binding etc

Additional rate for excavation of Pit for A type pole in Hard Laterite.

Providing concrete muffing (0.45x0.45x1.5m) inclusive of cost of all material (as per specification).

Additional rate for excavation of one Pit for HT Pole/HT Stay in Hard Laterite

Providing one Coil Earth using GI earth wire, digging separate pit at standard distance away from the pole/structure & backfilling.

Fitting and providing one HT Stay for 11kV pole incl. digging & back filling pit

Renewal of existing damaged/broken old 11kV Stay to the existing stay rod.

Dismantling (without damage) one km LT additional conductor line, cross arms, insulators and stacking the conductors in rolls.

Dismantling one LT 4 line cross arm from existing pole.

Transporting LT ABC by hired vehicle to a distance up to 5 km and carring up to 2 drum including loading and un loading using crane

Erection of Anchor clamp / dead end clamp for LT ABC of any size

Erection of suspension clamp for LT ABC of any size

Stringing of 1.1 kV Aerial bunched cable of size 3 x 70 + 1 x 16+1x 50 sqmm with bare/insulated Messenger through existing poles

Installation of Insulation piercing connector for main to service line main:16-95 sqmm, Tap 16-95 sqmm

Installing One No. Insulation piercing connector of size Main :16 to 95 ,Tap:1.5 to 16 Sq.mm

Dismantling and reconnecting Sph service connection from the OH line incl. lowering down the WP portion.

Dismantling and reconnecting 3ph service connection from the OH line incl. lowering down the WP portion.

Providing End Caps

Providing Cable Tie

Reconductoring one km LT Sph 2 wire OH old line with new ACSR Rabbit conductor incl. conveyance of materials.

Renewal of existing damaged/old LT TW/RSJ/Rail (Sph line) pole with new PSC pole in place and refitting of all items incl. conveyance (except pole).

Erecting one LT PSC Pole in position incl. digging & back filling pit.

Dismantling (without damage) one km LT Sph 2 wire OH line, cross arms, insulators and stacking the conductors in rolls.

Dismantling (without damage) one LT PSC/RCC pole after disconnecting stays, strut etc. and stacking the same.

Dismantling one LT 2 line cross arm from existing pole.

Providing Stay for LT poles incl. digging & back filling pit.

Renewal of existing damaged/broken old LT stay with existing stay rod

Fitting one No. Section fuse on LT line with dropping cables, crimping sockets, connecting with bolt&nut etc.

Cutting Channel/Cross Arm/Angle Iron into two pieces.

Drilling hole of various sizes on existing Channel/Cross Arm.

Insertion of one LT PSC pole in existing Sph OH line incl. digging & back filling pit, fitting cross arm, insulator, binding etc.

Providing Strut using LT PSC pole incl. digging & back filling pit.

Loading LT PSC pole from the stacking place and unloading the same at work site (transport by vehicle).

Transporting poles by hired vehicle to a distance upto 5km and carrying upto 4 poles excluding loading & unloading.

Loading HT PSC pole from the stacking place and unloading the same at work site (transport by vehicle)

Loading HT A type pole from the stacking place and unloading the same at work site (transport by vehicle).