Construction of Workshop Building at Kotdwar, Pauri Garhwal

Amount

Civil Work Diluting and injecting chemical emulsion (Chlorpyriphos/Lindane E.C. 20% with 1% concentration), at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surfaces of the excavations made for the foundation of the building, soil under floors, apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of Building shall be measured for Payment). 1-26-2

Diesel Tank Diluting and injecting chemical emulsion (Chlorpyriphos/Lindane E.C. 20% with 1% concentration), at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surfaces of the excavations made for the foundation of the building, soil under floors, apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of Building shall be measured for Payment). 1.26.2

Internal Electrification Supply of 1200mm dia ceiling fan Havells make (model Fusion II) i/c all complete. NS

Supply and Fixing of 145Watt. special light for industrial perpose IP65 PDC LED Highbay with circular form factor complete in all respects. NS

Supply of 300 mm exhaust fan model Ventil Air-DB (Havells make) complete with all accessories. NS

S/F of 100Amp. Four pole change over switch on 40mm x 40mm x 6mm angle iron frame, including the cost of labour, T&P painting and other material required for proper completion of the work as per direction and satisfaction of engineer in charge. UPPWD 378

S/F of 36W to 46W above 3300 indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of special Ploycarbonate meterial and driver set complete in all respect. CAT-AAA UPPWD 1406

Supply and fixing of recess/surface mounting round 15 to 18 Watt. LED Down lighter having podwer coated die cast aluminium housing with extended heat sink, diffuser/Reflector and driver set complete in all respect. CAT- AAA UPPWD 1403

S/F of LED Tube light with batten suitable for upto to 1 x 22 watt LED tube light fitting including with drive set complete in all respect. CAT-AAA UPPWD 1413 (A)

Supply & Laying of following size aluminium conductor PVC insulated armoured served sheathed cables 1100 volts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 16sq.mm. 4core 501 (i)

Supply & Laying of following size aluminium conductor PVC insulated armoured served sheathed cables 1100 volts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 25sq.mm. 3-1/2 core 501 (j)

Supply & Laying of following size aluminium conductor PVC insulated armoured served sheathed cables 1100 volts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 185sq.mm. 3-1/2 core 501

Transformer & Related work S/T of 160 KVA out door type 3 phase 3 STAR RATING, 50 Hz oil copper conductor step down core type transformer having a no load voltage ration 11/0.433 vedtor group ref. Dy -11 having tapping 5% on HT side for HT variation and leads to be brought out On Off circuit tap changing switch with locking device and outside locking device and outside indicator arrangement. The transformer shall have LT cable box on medium voltage side. The transformer will be confirming to IS-1180(Part-I) IS-2026 (Part I-V) with latest amendments confirming ISO 9001. HT SIDE: 3 nos. solid weather proof porcelain busing confirming ISS-3347 part III Fittings: 1. Rating & terminal marking plate. 2. 2 earthling terminals. 3. 2 tank lifting lugs. 4. Silica gel dehydrating breather. 5. conservator with drain plug or cover plate. 6. Plain oil level gauge. 7. Pressure release device through explosion vent disphron. 8. Oil filter valve 9. Oil temperature indicator aerial type. 10. Pocket on tank cover for thermometer 11. Pocket on tank cover for thermometer. 12. 4 nos. plain rollers 13. Trapping switch handle. 14. HT bushing fitting 3 nos. 15. LT bushing fittings 4 nos. 16. Earthing terminal 2 nos. 17. Oil filling hole with cap 1 nos. 18. Extra neutral provision 19. Air release plug. 20. Brain valve 21. LT cable box 22. Inspection cover (Approved Rate)

Installation & commissioning of transformer 160KVA (Approved Rate)

S/F of steel tubular pole 11 Meter long desinated 410 SP-55 in 1:4:8 cement concrete foundation including excavation back filling etc. complete in all respect. (Approved Rate)

S/E of overhead line with ACSR conductor on poles/service bracket including binding etc. complete in all respects. (Approved Rate)

S/E of overhead line with G.I wire no. 8 to 4 SWG on poles/service bracket including binding etc. complete in all respects. (Approved Rate)

S/construction of two poles sub-station structure comp with all accessories reqd. for proper comp of work on the S.T pole 11 mtrs long 410 SP - 55 (a) Supply of 11m long S.T pole i/c grouting concreting in 1:4:8 cement, c/sand OBB and plain thing with all materials. (b) Stone paid (c) S/F of M.S channel 100*50mm for disc with fitting and dropper (d) M.S bolts & nuts and washers (e) S/F of danger board with clamps (f) fabrication (g) S/F of 11 KV T.P.M.O completer in all respects. (h) S/F of 11 KV D.C. fuse set of appd make complete in all respects. (i) S/F of 11 KV pin insulator with PIN. (j) S/F of 11 KV disc. with fitting on channel. (k) S/F of 50x6mm flat clamp and packing piece for fitting channer droper channel. (l) Painting of structure with appd paint with one coat of red oxide primer, 2 coats of A-1 paint with post office red enamel and from top top at a distance of 2 mtrs. (m) Earthing i/c all complete (Approved Rate)

Supply & installation of 50 KVA Three phase servo voltage stabilizer suitable for 50Hz AC Supply with input voltage 260V-480V output voltage at 400v + 1% with dimmer not less than 100 Amp. Speed of correction to be 30 volts per second and regulation at Maximum 1% from no load to full load. Working temperature - 22 to 55 degrees centigrade from ambient and should be oil cooled. Transformer core to be pure CRGO with winding of Electrolytic prime grade copper with High/Low cut, single phase prevention and by-pass. The construction should be of MS sheet 16sq.mm powder coated body and mounted on uni-directional wheels, digital voltmeter/ampere meter with indicating lamps for voltage status. The specification should be displayed on the plate fixed on the body. (Approved Rate)

Minimast lights & Street lights Supply & fixing of 16 mtr High mast shaft of approved make with rising system hot dip glavanized inside & outside dip, heaving pole sheet thicknes 3 mm. Top dia minimum 150 mm, Bottom dia 360 mm base plate 32 mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for jhigh mast such as head frame suitable for 6 to 12 luminaries & its control gear boxes 1.5 HP power tool moter, 3 point suspention system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufacture drawing/site reuiment along with foundation bolts nuts, washers, anchor plates etc complete in all respect. UPPWD 652

S/F of factory wired integral LED flood light luminiare with die cast aluminium housing bolt with driver set suitable for 140 to 150 Watt, Confirming to IP 66 protection complete in all respect. CAT- AAA UPPWD 1454

S/L of 16 sq. mm 4 core aluminuim comnductor PVC insulated armoured served sheathed cacbles 1100 Vols grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt brick on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable sixe or as directed by the Engineer-incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. UPPWD 501(i)

S/F of LED streer light fiting having die cast aluminium body and diffuser with driver set suitable for 75 to 90 Watt, Confirming to IP 66 protection complete in all respect. CAT- AAA UPPWD 1423

Supply & fixing of 10 mtr GI Octagonal Pole of approved nake (top dia 100 mm, Bottom dia 200 mm and base plate 16 mm thick) having 3 mm thickness with double arm bracket 1 Mtr length in 1:2:4 RCC foundation bolt includinig the cost of foundation, excavation & back filling and required T&P complete in all respect. UPPWD 650

Supply & erection of 32 Amp. TPN tap off box on rising mains complete with HRC fuses etc. complete in all respect. UPPWD 912

Handpums with submersible pump Transportation of suitable truck mounted ODEX drilling rig machine with all necessary connection T&P required for drilling including instalation and loveling of Rig machine etc. complete in all respect as per direction of Engineer/incharge. NS

Dirilling of bores as per IS 2800-1979 using ODEX 115 (Tubex) attachment required drilling in alluvial, boulder, pebbies, gravel, rockey stone, sticky clay etc. including cost of attachement consumable stores bits water POL etc. complete with system of simultaneous lowering of 125 mm nominal bore 5.4 mm thick MSERW fin cut casing pipe complete in all respect as per direction of Engineer-in-charge. NS

Supply & Lowering/Fixing of 125mm dia 5.4mm thick as per ISS 1239/4270 MSERW fin cut casing pipe from approved manufactures complete in all respect. NS

Supply and Fixing of suitable casing shoe of EN-24 steel as per requirement of ODEX Attachment complete in as respect. NS

Supply & Lowering/Fixing G.I. Riser pipe 32mm nominal bore, hot dipped gaivanized, screwed and socketed pipe in 3mtr. Length conforming to IS 1239 (part-1)/2004 mediam class socket manufactured from aeamiess pipe or machined from solid bar conforming to grade Fe 410-S of IS 226/1975 with the dimensions (length and diameter) specified in IS 1239 (Part-II)/2004 hot dipped gaivanized etc. NS

Chemical & Becteriological test of water sample NS

Supply of 5HP Submersible pumpset 3 phase 230V complete with enlarger etc. KSB/Crompton make all models. NS

Labour work for lifting, lowering, column pipe 32mm dia with motor & pump and cartage complete. NS

S/F of 5 HP motor starter panel L&T /Cropmton/ BCH make complete in all respects. NS

S/F of 6 sq.mm. 3 core of flat submersible cable Finolex/L&T/Havell's make complete in all respects. NS

Bidder Name

Amount

M/S Kumar Construction

Satya Sai Builders And Contractors

M/S SINGH ASSOCIATES

M/S Kumar Construction

M/S SINGH ASSOCIATES

M/S Kumar Construction

M/S SINGH ASSOCIATES