PROVN OF FOL STORE AT BDE SIG COY IN ZONE R, 12 X SCOOTER / CYCLE STAND NEAR BLDG NO T-56 IN ZONE O AND BUS STOP FOR JCOs MD ACCN IN ZONE F AT MIL STN AGARTALA

Amount

Schedule'A' Part-I: B&R works

Excavation in trenches n.exc 1.5 M wide and n.exc 1.5m deep as in soft/loose soil for foundation etc or for shaft walls, cesspit, manhole etc n.exc 10Sqm on plan

M & L for PCC 1:4:8 type D-2 (using 40mm graded aggregate) as in foundation filling and mass concrete.

M & L for cement concrete (1:3:6) Type C2 using 40mm graded aggregate in foundations, filling and mass concrete

Material and labour for brick work with locally available sub class ‘B’, old size, best quality bricks, straight or curved on plan exc 6 m mean radius built in cement mortar ( 1:6) all as specified and directed.

M and L for half brick thick brick work sub class 'B' brick straight or curved on plan to any radius in CM 1:4 complete all as spd and directed .

M & L returning, filling including spreading, levelling and well ramming in layers not exceeding 25 cm in each layer as in hard / dense soil complete.

M & L earth filling under floor spreading and levelling in layers n exc 25 cm thick for well ramming watering required.

M&L TMT bars of 10mm dia and over cut to lenth, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.

M and L for TMT bar 6 to 8mm dia as in stirrups, spacers and binders

M and L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat

M&L form work for flat fair finished surfaces of concrete to soffits of suspended slabs such as roof slab not exceeding 200mm thick

M&L for rough finished surfaces of concrete flat formwork to sides and soffits of floor or roof beams, lintels, cantilevers shelves etc

M and L forwork to sides of pillars, posts, struts, piers, columns and stanchions

M & L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail?ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon?tal or sloping and similar work exc 10cm but n exc 20cm wide

M&L RCC type B-1 (1:2:4) using 20 mm grades aggregate in slab, supported on walls beams and columns in floors roofs landings

M & L for RCC type B-1 (1:2:4) using 20mm graded agregate in beams, antilevers, bressummers, lintels over 1.5m span

M & L for RCC type B-1 (1:2:4) using 20mm graded agregate in column, piers, struts

M and L for ceiling plaster 5mm thick in CM 1:3 incl preparation of surfaces.

M and L for 02 coats of white wash on ceiling incl prep of surfaces

M&L for 15 mm thick rendering in CM 1:4 in finishing the surface even and smooth without using extra cement. (WPC shall be measured and paid seperately)

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint and over one coat of alkali resistent priming paint complete all as specified and directed.

M&L for 15 mm thick plaster on fair faces of brick or concrete surfaces in CM 1:6 finshed even and smooth without using extra cement complete all as spd.

S&F steel windows with side hung shutters including box type hinges with one No MS handle per leaf made of FI 25 x 3 mm made to shape Appx 200 mm in length and two Nos 150mm long MS tower bolt welded to each shutter including 150 mm long peg stay, complete with glazing bars, dovetailed or welded all as specified.

All as per item No 23 above but without glazing bars complete

S&F steel ventilator with top hung shutters including box type hinges with steel hndle and steel peg stay,MS 10mm square guard bar, Glazing bar devotailed or welded for receving glass and including cutting holes in walls for fixing the window with hold fast in PCC (1:3:6) type C1 (using 20mm graded aggregtetes ) and making good the disturbed surfaces in CM (1:4) and with the existing finishes to match complete all as specified and directed.

S&F framed wrk such as grills, grating etc with ends of bars shouldered and/or rivited or forged into spikes: framed guard bars;barried iron doors ladders,framed balasters walk ways railing framed work of water and simler work confirming to Fe-410-0 or 310-0-using 12mm square bar cmplete all as specified and directed.

S&F for galvanised mild steel cloth of 0.56mm nominal dia wire average width of aperture 1.18mm fixed with tinned tacks or galvanised wire stapples or wooden beads for wooden shutters all as spd.

S&F sheet glass 3mm thick ordinary quality and fixed to steel or wooden frame withold putting or wooden beads n.exc 0.5 sqm each pane all as spd.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described.

M and L for 75 mm thick PCC 1:2:4 type B-2 40mm graded agg in plinth protection

Surface excavation n.exc 30cm deep and avaraging 15cm deep and getting out in soft/loose.

M & L hard core of broken stone boulders to gauge n exc 63 mm all as spd and directed by Engineer-in-charge.

Demolition RCC slab at any posn as directed by Engr-in-charge

Removing excavated material n exc. 50m and depositing where directed at a level n exc1.5m above the starting point.

M & L for broken brick aggregate hard core of gauge not exec 63 mm deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed toa true surface all as specified and directed by Engr-in-charge.

M&L for 100 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for providing 75 mm thick cement concrete type C-2, 1:3:6 using (40 mm graded brick aggregate) as in path or paveway finished rough without using extra cement complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 Type B-1 using 20 mm graded stone aggregate 25 mm thick and the surface is finished rough to receive the topping layer.

Supply of Liquid water proofing compound : Make Dr fixid ( as per manufacturers & Instructions).

Excavating post holes (or similar holes) each n.exc 0.5 cum getting out,returning filling and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm watering and removing surplus soil to a distence n.exc 50m making gd surface soft/loose soil surface all as specified and directed.

S&F for rolled mild steel in joist channel angle or Tee section fxed indipendently wthout connecting plates etc confirming to Fe-410-W(Gde-E-250) quality-B of all specified and directed.

S&F for rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe-410-W(Gde-E-250) quality-B of all specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws as specified.

Cement concrete Type B2 1:3:6 (40 mm graded aggregate) in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as per Specified and directed by Engr In Charge

S&F Steel works in tubular trusses, Vertical posts etc including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 complete all as specified and directed.

S&F MS steel section as in purlins, rail etc etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 and painted one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and directed.

S&F rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes ,without and attachment of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S&F Mild steel bolts. purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Dia of bolt 16 to 20mm and length exc 30cm long and n exc 45cm complete as specified.

S&F Mild steel bolts. purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 5cm long but n exc 10cm long with dia of bolt 12mm complete

S & F Colour coated cold rolled FRP plain Roofing Sheet in roof covering/cladding/ eaves board fixed with selp tapping screw complete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in valley gutters fixed with selp tapping screw complete all as specified and directed.

M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and joints are filled with white cement with no pigment laid over 15mm thik screed bed in CM 1:4 complete all as specified and as directed

M&L for PCC (1:2:4) type B1 using 20mm graded stone aggregte in coping etc including use of form work and finishing all exposed faces of concrete even and smooth without using extra cement all as specified .

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:4)

S&F of PVC 110 mm bore (SWR) pipes single socket, in any length with rubber ring joint, fixed to wall with clamps as required etc complete all as specified and directed.

S&F in repair PVC (SWR) bend of 110 mm bore etc complete all as specified and directed.

S&F Stainless steel pipes of grade 304H, polished for ladder of swimming pool and in parapet railing complete all as specified and as directed.

Schedule'A' Part-I: E & M works

M & L for point wiring with 1.5 Sqmm nominal cross sectional area, PVC insulated, FR unsheathed, 1100 volt grade, multistranded single core copper conductor and including stove enameled minimum 25 mm wide with all fittings and accessories such as bends, Tees, Joints etc fixed to wall or ceiling and Recessed mild steel switch board of required size including bakelite sheet of 3 mm thick with chromium plated screws or rectangular aluminium box closed recessed having 40 mm depth ISI marked ISI No 14772 for fixing of switch etc and provision of 1.5 sqmm nominal cross sectional area, PVC insulated, FR unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for eath continuity connected to earth dolly, all metal parts, such as tube light fittings, fan hook, earth terminal of all socket points etc as specified and directed.

One light / Fan / Bell Point controlled by one way.

Supply and fixing LED lights fitting 1x 8 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size. all as specified and directed.

Supply and fixing light fitting 1 X 9 W/ 1 X 10W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Supply and fixing ceiling rose, surface bakelite, 65mm x 50mm , two to three terminals complete all as specified & directed.

Supply & fixing switch piano flush type (ISI marked), single pole, one way 5/6 Amp, 240 Volts complete all as specified & directed.

Switch flame proof rotary type with termination box in LM6, 16A, single pole 250 V

S &F Miniature circuit breaker single pole 6 Amps to 32 Amps, 230 volt, 10 KA, C-curve all as specified and directed.

S &F Miniature circuit breaker triple pole and neutral 32 Amps, 230 volt, 10 KA, C-curve all as specified and directed.

Supply & Fixing sheet metal enclosure with single door for DBs conforms to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector, 4 way, 240 Volt .

XLPE insulated, armoured heavy duty electric cable with aluminum conductor, 1100 volts grade, cross-sectional area 4 Sqmm. 2 Core.

NOTES :- 1. The amount of schedule of credit shall be deducted from the total of this BOQ for arriving at contract sum. 2. Unless otherwise specified the rates for PCC shall deemed to include the cost of formwork shuttering etc, required for complete and proper execution of the work. Refer Schedule 'A' notes for details.

M/S SANKAR GOPE

M/S PRITAM ENTERPRISES

SUMAN DEB