SPECIAL REPAIR / RENOVATION OF 21 UNIT OF STAFF QTRS UNDER AGE (I) LANSDOWNE.

Amount

Excavating in trenches n'exc 1.5 m width and n'exc 1.5 m in depth for foundation etc / for laying of cable/ pipe etc n'exc 10 sqm on plan and n'exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed.

Removal of surplus soil to a distance n'exc. 50 Mtr and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

Removing building materials etc. (other than spoil ) to a distance exc 1.0 Km including loading, unloading complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Demolition of RCC in Roofs, floors ( other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforced) including cutting of reinforcement to facilitate demolition complete all as specified and directed. Note : Reinforcement obtained from demolition will be considered credit Sch as scrap iron.

M&L for RCC (1:2:4) Nominal mix (using 20mm graded stone aggregates) as in floor/ roof beam, cantilevers, lintel over 1.5m span complete all as specified and directed.

M&L for formwork for rough finish to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for PCC (1:7:12) Type F2 (40 mm graded aggre-gate) as in foundations, sunken portion filling and mass-concrete complete all as specified and directed.

M&L for mild steel TMT bars 5 to 10mm dia bars as in stirrups cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with old size full brick subclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed.

Demolition of PCC in ground floor and pavings not exc 15 cm thickness below or above ground level including removal of rubbish out side MOD land complete all as specified and directed.

M&L for hard core of broken boulders/stone of gauge n exc. 63 mm, deposited, spreading, leveling watering and well ramming to true surface in layers not exceeding 15 cm thick each layer complete all as specified and directed.

M&L for 75 mm thick PCC (1:4:8) type D2, (40 mm graded stone agg) as in sub base of floor/ hardstanding/ footpath complete all as specified and directed.

M&L 75mm thick PCC (1:2:4) type B2 (40 mm graded stone agg) as in hard standing/ path finished even and fair without using extra cement laid in alternate panel with and including provision of constrction joint filled with sealing compound grade 'B' complete all as specified and directed. Note : Size of panels will decide by AGE (I).

Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water and removing unseviceable materials out side MoD land complete all as specified and as directed.

M&L for 15mm thick plastering on fair faces of brick wall in two layers, Ist layer 10mm thick CM (1:6), and IInd layer 5mm thick CM (1:4), surface finished even and fair mixed with @ 200ml per bag WPC (liquid type) complete all as specified and directed. Note :- WPC (Liquid type) shall be measured and paid separately as supply only.

Supply only liquid water proofing compound LW plus or Dr Fixit or Fosrock compound complete all as specified and directed.

M&L for 10mm thick rendering on other than fair faces of brick work or concrete surface in cement plaster (1:6) finished the surface even and fair complete all as specified and directed.

M&L for 5mm thick rendering on fair faces surface in cement plaster (1:3) as in ceiling and fininshed surface even and fair complete all as specified and directed.

M&L for three coats of white wash on new ceiling surfaces including preparation of surfaces complete all as specified and directed. Note :- The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge.The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted.

M&L for preparation of old decorated surface of interior wall by complete removal of existing treatment with mechanical sander (rpm 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers and application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper over a coat of primer of same make all as specified and prescribed by manufacture of paint/ distemper, by using roller/ spray machine complete all as specied and directed at site by Engineer-in-Charge.

M&L for preparation of old decorated surface of exterior wall by complete removal of existing treatment with mechanical sander (rpm 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers, then washing the surface with Bleaching powder solution for treatment of fungal growth and applying two coats of exterior anti fungal acrylic emulsion paint of required shade (wallmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint/ distemper by using roller/ spray machineand with and including application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper complete all as specied and directed at site by Engineer-in-Charge.

M&L for preparation of newly plastered surface of external wall all as prescribed by manufacture of paint and applying two coats of exterior anti fungal acrylic emulsion paint (walmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint/ distemper by using roller/ spray machine with and including application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper complete all as specied and directed at site by Engineer-in-Charge.

M&L for preparation of newly plastered surface of interior wall by application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper over a coat of primer of same make all as specified and prescribed by manufacture of paint/ distemper, by using roller/ spray machine complete all as specied and directed at site by Engineer-in-Charge.

Note for item No 24 to 27 :- (i) The old/ New surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacture instruction before application of distemper. The cost of materials, labour and T&P required for preparation of surface are demand to be included in the rates quoted. (ii) The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE/ AGE (I) before commencement of work. (iii) All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by deportment for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv) after carrying out preparation of surface the same shall be got approved from GE /AGE (I) before application of distemper for each building. (v) Before commencing the work, contractor will got the written approval from GE/ AGE (I) for the make and colour / shade (tint). (vi) The cost of Scaffolding wherever required are deemed to be included in the rates quoted by the contractor.

S&F 5mm thick beveled edge best quality looking mirror of size complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even & smooth without using extra cement, with and including joint filling (Size 30mm deep x 10mm wide) with sealing compound grade-A at 3m interwal and corner complete all as specified and directed. Note : Joint to be provided at each interval of 3m and corner and cost of the same deemed included in quoted rate.

M&L for PCC (1:3:6) type C-2, using 40mm graded stone aggregate as in surface channel and drain including saucer drain and toe wall etc complete all as specified and directed.

M&L for extra for forming fair finished drain, or channel, 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred, stopped ends, complete all as specified and directed.

Add or deduct from item No. 32 for each 25 mmm girth or part thereof over or under 30Cm complete all as specified and directed. Note:- For adjustment only and quantities may be varied (Plus/Minus) to any extend as per site requirement.

Taking down chowkhats or frames with shutters ( without taking off shutters from the frames) of following size complete all as specified and directed:-

Area not exc 1.5 sqm each

Area exc 1.5 sqm but not exc 4 sqm each

Taking down shutters of any description, of following size complete all as specified and directed:-

Area exc 1 Sqm but not exc 2.0 Sqm each

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows and other frames/ chowkhat of following size comprising of virgin PVC polymer having K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and direction. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable and variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (ii) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid for separately.

65mm x100mm size

65mm x 125mm size

M&L for 30mm thick factory made solid WPC (wood plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texteure, including stainless steel wire mesh shall be fixed with 15 x15 mm square tube in side rails with screwing 8 x 28 heat metal zink coated screw can be remove or fix again after changing of wire mesh, when needed. The density of the shall be as per manufacture instruction compete all as specified and directed.

S&F Factory Made 30mm thick 100% Solid WPC Single extruded ( Wood polymer Composite ) Moulded Door Shutter Spray Painted with solvent based colour, of required size with 2,4 or 6 raised panel design on front side with 10mm deep mould on single side with grain texture comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 600 kg/cbm manufactured by an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company.

S&F windows & ventilators, fabricated from rolled formed GI Section made of Galvanised steel colour coated (PPGI Sheets) (Base steel as per IS 513 ‘’D’’ quality). Galvanised as per IS 277 with Zinc of 90 Gsm/SqMt w. PAINT: Pre-Painted sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick.GI Section of 0.58mm thick in Double rebate windows in which both glazed shutter and gauge (flymesh) shutter, 74 X 60mm outer frame, Mullion 72 x 49mm, Glazed shutter 48 x 22mm, Flymesh 41 x 22mm, Beading with round ends for Glass Fixing 12 x 12mm in fixed portion and the outer frame and mullions to have rebate for glazed/ gauzed shutters the sections cut to length metre joined with corner PolyVinylChloride brackets centre mullion fixed with PolyVinylChloride Mullion caps. Glass of 4mm thick plain float glass fitted with Ethylene Propylene Diamine Monomer in glazed shutter and wiremesh of Stainless steel of 36 guage to fix mesh in mesh shutter using VC Black Gypsum Drywall screws and Spoon profile of 0.58mm GI Sheet. Corners of the windows should be joined with corner brackets made of polyvinylchloride with crca of zinc phosphate coat.Each glazed shutter and fly mesh shutter shall be provided with SS Pivot Hinges 2 in each, PolyVinylChloride handle 1 in each and Powder coated Peg stay in Glass shutter.Window shall be provided with Powder coated MS Grill/Guard Bars made of 10mm MS Sq Bar welded to 6 x 12mm MS Flat with countersunk holes at both vertical ends . Gap between the bars should not be more than 150mm. Window frames shall be fixed to brick / concrete masonry by using nylon self expension caps & 75/100 mm MS screws after drilling in walls. VC Black Gypsum Drywall screws should be used while fixng corner brackets,stay,hinges,mullion caps of windows complete all as specified and directed.

M&L for preparation of old painted surface of wood and wooden based material of any description over 10 cm width or girth and applying two coats of synthetic enamel paint (1st Quality) with and including complete removing of old paint by paint removers or burning off by blows and cleaning with scrapers, any number of coats complete all as specified and as directed.

M&L for preparation of old painted surface of steel material of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed.

S&F cornor shelf of 3 tier assembly consisting of 5.5mm thick sheet glass self 15cm radius with chromium plated frame with bracket guard and rail and fixed with CP screws and plug sizenot less than 450mm as suitable for bathroom and as per manufacturer instructions complete all as specified and directed.

S&F hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws of following size complete all as directed and specified :-

S&F stainless steel barrel tower bolts of extruded section (ISI Markd) of following size complete all as directed and specified:-

200 mm long

150 mm long

S&F stainless steel handles fabricated type, of following size complete all as directed and specified:-

150 mm long

125 mm long

S&F stainless steel sliding door bolt with hasp & Staple, bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate of following size complete all as specified and directed:-

300mm long

250mm long

S&F stainless steel, non magnetic butt hinge (ISI Marked) and fixed of following size complete all as specified and directed:-

100 mm long

75 mm long

S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

S&F in repair 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

S&F stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or wire staples complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F framed work as in iron enclosure, doors or gate of angle iron or other section with gussets plate, rails, braces etc drilled for fixing of steel seating other covering, door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel handing door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and as directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account.

S&F mild steel work with flat iron as in hand rail (railling for stair case), hold fast, wind ties over roof covering conforming to Fe-290 Gde E-165 steel with and including necessary drilling holes etc and similar work complete all as specified and directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and or riveted or forged into spikes, framed, barred iron door, ladders, fencing work ect. conforming to Fe-290 Gde E-165 complete all as specified and directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account.

M&L bands, straps, supports or stays for rainwater (stack clamp), ventilating pipes, including bolts, if required, hooks (stays), heavy for large gates, hooks and pintle hinges large hasps and staples, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts two way and three ways straps, plate washers and similar articles conforming to Fe-290(Gde-E-165) complete all as specified and directed.

M&L for 60mm thick coloured rubber moulded glossy finish machine pressed precast concrete interlocking paver block, M-35 Grade with pre-polished, coloured/ laquar finish any shape and size, as approved confirming to IS 15658-2006 with and including over 40mm thick stone dust/ sand cushining complete all as specified and directed.

Supply only MS galvanized chain link fencing complete all as specified and directed.

M&L for taking down of existing sunken slab treatment from the sunken portion and cleaning the surfaces by washing down with water and rubbish off the permises including as under:- Cleaning and filling crackes with sealing compound brushing neat with neat cement slurry@ 3.0 Kg per Sqm and grouting in 25 mm thick PCC 1:2:4 type B-0 using 12.50 mm graded stone aggregates over suken slab portion and finishing the top surface even and smooth without using extra cement and carrying out the roof treatment by applying the following process through authorised applicator of the company:- (i) MPB coating or URP coating by applying primer coating of Dr Fixit Pidicrete URP duly mixed with cement in ratio 3:10 by weight. (ii) URP coating by applying primer coating of STP ShaliCrete URP duly mixed with cement in ratio 1:5 by weight. (iii) Applying two coats of STP ShaliCem EWP/Dr Eixit Pidifin 2K as per manufacturer's instructions. (iv) Applying 10 mm thick rendering of mortar obtained by mixing portland cement-50 Kg, Washed sand-150 Kg, STP ShaliCrete URP/Dr Fixit Pidicrete URP 6-7.5 Kg and water 10 Liters.

Removal of existing roof treatment i.e APP membrane and open up RCC roof slab including picking, sweeping cleaning with wire brush and washing down with water to remove dust, dirt to get surface free of laitance, scales, oil or any other loose material complete all as specified and directed. Note for all Item of roof treatment :- The work is required to be carried out at non-accessible roof for double storey. The contractor shall make arrangement of scoffolding, safety & security of workers and arrangement for approach to roof. The rates quoted shall deemed to be included for these items .

M&L 25 to 50mm thick PCC (1:2:4) type B-0, using 12.5 mm graded stone agg mixed with SBR Latex liquid polymer as water proofing compound (mixed as per manufacture instructions) over and including one coat of cement slurry admixed with acrylic bonding compound SBR Latex liquid polymer as to be used for bonding of new concrete/ mortar to old surface as per manufacturer direction and finishing the surface even and smooth without using extra cement as in roof padding / sunken floor to receive water proof treatment complete all as specified and directed. Note :- The cost of SBR latex deemed included in quoted rates.

M&L for one coat of cement slurry admixed with acrylic bonding compound SBR Latex liquid polymer (slurry will be prepared as per manufacturer direction) as to be used for bonding of new concrete/ mortar to old surface complete all as specified and directed.

M&L for water proofing treatment to non-accessible roof slab with APP based modified polymeric membrane as per manufacturer’s instructions with following course of description below :- (a) Applying a priming coat of bituminious primer @ 0.30 Kg /Sqm, till the surface is properly impregnated. (b) Providing APP based 5 layer polymeric membrane minimum weighing 3.6Kg/ Sqm and minimum 3mm thick reinforced with polyester non-woven fabric (weight not less than 150 gms/sqm) centre core, laid on primed surface by forced applications as per the manufacturer's instructions with side over lap of 75 mm and end overlap of 100 mm. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer (torching overlap by propane or butane gas torch ) and sealing it with the help of hot trowel. The overlap joints shall be made as a monolithic layer (c) Apply two coat of bituminous aluminium paint @ 0.20 Kg/Sqm over APP membrance

Note : (i) The work of water proofing treatment shall be got executed through authorised applicator of the manufacturer only and 10 year company back warranty to be submitted by contractor. (ii) The work is required to be carried out at non-accessible roof slab for double storeyed. The contractor shall make arrangement of scaffolding, safety and security of workers and arrangement for approach to roof . The rates quoted shall deemed to be included for these items.

M&L for precast RCC (1:2:4) type B1, (using 20mm graded stone aggregates) as in cover slab (for manholes) and set in CM (1:6) including necessary fair finish formwork complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips complete all as specified and as directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty/ wooden/ PVC/ aluminium beading, in square of following size in each pane complete all as specified and as directed.

Not exc 0.5 sqm in each pane

Exc 0.5 sqm in each pane

S&F 3 mm thick figured glass, pin headed type and glazing with oil putty /wooden beads in square n. exc 0.5 sqm in each pane complete all as specified and as directed.

S&F 18mm thick prelaminated, medium density MDF, interior grade with one side decorative choice laminations and other side balancing white laminations, fixed with auto hinges to timber/ steel frame work as in cup boards, drawer, etc with shelf and shutter incl lipping to edges of exposed edges of same texture and shade with and including stainless steel cleat of suitable size for fixing arrangement complete all as specified and directed.

S&F 18mm thick PVC solid, both side prelam celluca plyboard for cabinet boxes & shutter, cup boards, drawer, etc with shelf and shutter incl lipping to edges of exposed surface including provn of auto hinges for fixing arrangement complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises from MoD land complete all as specified and as directed.

M&L for coloured vitrified tiles of any design and pattern, double charged, 9 to 10 mm thick, as in floor etc incl 15 mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B1b with average water absorption less than 0.05%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 4.0% (Max deviation). Centre & Edge curvature and warpage + 0.20% (Max Deviation). Breaking strength 1200 N (Minimum) and minimum 95% tiles shall be free from visible defects and area of each is as following complete all as specified and directed :- Note: Shade of the tiles including Colour, design and pattern shall be got approved by GE/ AGE(I).

Area of each tile not exc 0.36 sqm.

Description same all as per item No. 72 but in riser of steps, skirting, dado and pillar etc with and includind over 10mm thick rendering in CM (1:3) complete all as specified and directed.

M&L for mat finished, joint free coloured ceramic tiles of any design and pattern, 7 to 8 mm thick, of following size, as in floor etc with and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622.2006, Group B II with average water absorption between 0.5% to 3%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 5.0% (Max deviation). Centre & Edge curvature and warpage + 0.50% (Max deviation). Breaking strength 1300 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed :- Note:- Shade of the tiles including Colour, design and pattern shall be approved by AGE (I).

Area of each tile exc 0.06 Sqm but not exc 0.11 Sqm.

Area of each tile exc 0.18 Sqm but not exc 0.38 Sqm.

Description same all as per item No. 74 & 74.2 but as in riser of steps, skirting, dado and pillar etc with and includind over 10mm thick rendering in CM (1:3) complete all as specified and directed.

M&L for coloured glazed ceramic tiles of any design and pattern, 300x450x 7 to 8mm thick, as in dado etc including 10mm thick rendering in CM (1:3), set and jointed in neat cement slurry and pointed in white of coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B III with average water absorption between 10% to 15%. Length, width and straightness of sides + 0.20% (Max deviation). Thickness + 4.0% (Max deviation). Straightness of sides and Rectangularity +0.15% (Max Deviation). surface flatness + 0.22% (Max deviation). Breaking strength 500 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed. Note: Shade of the tiles including Colour, design and pattern shall be got approved by AGE(I)

S&F in repairs drapery rod powder coated, fancy type, made out of 25mm dia MS pipe having wall thickness 0.63mm bright finish, colour and pattern as approved by AGE (I) complete all as specified and directed. Make: Aerolux/ MEC/ Vista.

S&F in repairs mild steel powder coated brackets, fancy type, as approved by AGE (I) suitable to hold the drapery rod/ curtain rod 25mm dia and fixed to wall (concrete/ brick masonary) with the help of 2Nos 50mm long steel screws and rawl plug including drilling with electric drill and making good the disturbed surface complete all as specified and directed. Make: Aerolux/ MEC/ Vista.

S&F in repairs Vitreous China wash down water closet pan (Pedestal pattern) incl close seat cover, hinges, fixing accessories and accessories set and cistern with cistern fitting complete, flush pipe incl all joints complete all as specified and directed. Make – Jaquar Cat No-ECS-WHT-851S220NPP or equivalent model of make as specified in appendix.

S&F in repair vitreous china squatting pan of “Orissa” pattern of size 580 mmx 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed. Make :-Jaquar & Coy Pvt Ltd , Cat Part No. ECS-WHT-451E/ CERA Sanitaryware Ltd, Cat Part No. S3010110 / Prayag Polymers Pvt Ltd, Cat Part No.- 4054.

S&F in repair chromium plated health fauset, telephonic type with CP flexible arms and hooks of approved make suitable to fix to 15mm bore CP angle valve complete all as specified and directed.

S&F vitreous china wash hand basin, white, flat back, size 550mm x 400mm excluding taps, chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets, waste pipe & CP brass waste coupling of 32mm dia complete all as specified and directed. Note : Rate quoted under this item deemed included fixing of taps, plug and chain and connecting up to supply pipes, wastes or traps etc.

Supply only 15 mm dia brass chromium plated central hole wash basin mixture, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut capstanhead screwed for 15mm dia pipe complete all as specified and directed. MAKE: Jaguar, Model CON-169KNB (Continental series) or equivalent other make as specified in appendix.

S&F in repairs 15 mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated , Fancy type screwed down for pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified and directed. MAKE: Jaguar, Model CON-021KN (Continental series) or equivalent model of make as specified in appendix.

Disconnecting and dismantling of water storage tank and removing from the site of following capacity of tank complete all as specified and as directed:-

Capacity exc 500 Ltr but not exc 1000 Ltr

S&F rotational moulded polyethylene water storage tank, double layer construction, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings, of following capacity of tank complete all as specified and as directed:-

Capacity 1000 Ltrs

S&F ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipes or brass ferrule and fixed of following size complete all as specified and as directed :-

20mm bore ( minimum weight 210gms)

S&F in repair PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia of make as approvrd by GE complete all as specified & directed. MAKE: Prayag Polymers Pvt Ltd, Cat Part No. 504 or equivalent of make as specified in appendix.

S&F in repairs PVC (SWR) pipes single socketed in any length with rubber ring joints and laid in trenches or in floor of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F in repairs PVC (SWR) pipes single socketed in any length with rubber ring joints and fixed to wall of following size complete all as specified and as directed :-

75 mm bore

S&F PVC (SWR) bends any radius including necessary cutting in brick wall and making good to match with existing surface of following size complete all as specified and as directed :-

75 mm bore

S&F PVC (SWR) junction single, (single T) with access door equal or unequal of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F PVC (SWR) vent cowl of following size complete all as specified and as directed :-

75 mm bore

S&F PVC (SWR) floor trap, out let dia 75mm, plain with grating including jointing with solvent complete all as specified and as directed.

S&F PVC (SWR) P trap, out let dia 110mm, plain with grating including jointing with solvent complete all as specified and as directed.

S&F PVC (SWR) reducers of size 110 mm x75 mm complete all as specified and directed.

M&L in repair for cast iron Nahani trap with grating including jointing to waste pipe fixed in PCC (1:2:4) type B1, for following size complete all as specified & directed :-

75mm dia

Demolition and breaking up drain pipes (PVC/ SGSW/ AC/ RCC pipe) of following bore of pipe, set in cement mortar complete all as specified and as directed:-

150mm bore

M&L concrete bed to pipes in PCC (1:3:6) type C2 (using 40mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid on slope and tested for following bore sewer pipe line complete all as specified and directed :-

150mm bore

M&L for 150mm bore PVC pipe, Type B, laid and jointed complete all as secified and directed.

S&F chromium plated brass tubular towel rail, D type, 60 cm long between flanges complete all as specified and directed. MAKE: Jaguar, Model ACN-1111NM (Continental series) or equivalent model of make as specified in appendix.

S&F in repair Glass shelf with Sheet Glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long.complete all as specified and directed. MAKE: Jaguar, Model ACN-1171N or equivalent of other make as specified in appendix.

S&F in repair 15mm bore angular stop valve with flange, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed. Make:- Jaquar, Cat Part No. CON-059KN or equivalent of make as specified. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site

S&F stop valve, cast copper alloy with crutch handle, screwed for iron pipe or for brass ferrule and fixed of following size complete all as specified and directed:-

20mm bore

S&F in repairs 15 mm dia bore bib taps, long body, cast copper alloy with fancy type, chromium plated capstan head long body with wall flange, screwed for iron pipe, or for brass ferrule complete all as specified and as directed. Make : JAQUAR, Cat Part No. CON-107KN or equivalent make as specified.

S&F in repair wall mixer with with connector for hand shower arrangement with connecting legs, wall flanges and wall bracket for hand shower and shower arm chromium plated for mixing hot and cold water screwed for iron pipe suitable for 15mm bore pipes complete all as specified and directed. Make : JAQUAR, Cat Part No. CON-267KN or equivalent of other make as specified.

S&F in repairs Chromium plated shower rose 120 mm size with or without swivel joints, any size, including fixing to 15mm GI pipe or union complete all as specified and directed. Make : JAQUAR, Cat Part No. OHS-1789 or equivalent of other make as specified.

Supply only PVC connection 15 mm size with PTMT nut of following length complete all as specified and directed :-

S&F in repair PVC connection 15 mm size with PTMT nut of following length complete all as specified and directed :-

S&F grating doom 100mm dia of PTMT (with waste hole or without waste hole)(Min wt 25 gms) complete all as specified and directed.

S&F grating doom 125mm dia of PTMT (with waste hole or without waste hole)(Min wt 40gms) complete all as specified and directed.

M&L for 18-20mm thick granite stone slab (of any type) work (table rubbed and mirror finish polished) with and including necessay notching, chamfering the edges in steps, jambs, pillars, window-cills, cooking platforms and like bedded over and including 15mm thick screed bed in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F in repair stainless steel sink with out draining board, made out of 1.00 mm thick sheet for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever brackets, connecting union overall size 495mmx420mm with bowl size 410mmx 330mmx160mm complete all as specified and directed.

M&L for mirror polished machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror finish polishing over and including 15mm thick screed bed in cement mortar (1:3) complete all as specified and as directed Note:- The size of kota stone slab not less than 550mmx550mm (cut size except the location where balanced.)

Description same all as per item No 114 above but, as in skirting/ dado (10-12mm thick Kota stone) over and including 10mm thick rendering in cement mortar (1:3) complete all as specified and as directed.

M&L for rubber moulded coloured glossy finish chequered cement concrete tiles, ISI Marked, set and jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 15mm thick screed bed in cement mortar (1:4) for following size of tile complete all as specified and as directed:-

20cm x 20cm x 25mm thick

S&F soap dish recessed type (stainless steel) fixed with CP screws and wood cleats with wall complete all as specified and directed. MAKE: Jaguar, Cat Part No. ACN-1131N or equivalent model of make as specified in appendix.

Taking up or down steel water tubing (GI Pipe) and connections of following bore complete all as specified and as directed :-

15mm bore

20mm bore

S&F galvanised steel water tubing (GI pipe), medium grade with all fittings (ISI Marked) and fixed to wall, floor and ceiling or laid in trenches of following bore complete all as specified and as directed :- Note :- 80mm and 100mm bore pipe will be jointed by welding as directed at site

15mm bore

20mm bore

M&L for cutting chases in brick wall, pinning in and making good in cement mortar (1:3) to match with existing surface for following girth complete all as specified and as directed :-

Cutting not exc 10cm girth.

Supply only 32 mm bore PVC flush pipe low or high density polythene pipe min 800mm long as required at site and fixed as in waste pipe complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed

S&F in repair stainless steel kitchen plate rack 0.80mm thick sheet of over all size 24" x 36" x 10" fixed with steel screws and steel rawal plugs complete all as specified and directed. Make – Prayag Cat Part No- P 336 or equivalent others make as specified. Note :- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site.

Dismantling and taking down old unserviceable point wiring of any type (light, fan, socket, power etc) complete with fitting such as switches, sockets, ceiling roses, pendants, lamp holders, light fitting etc including CI/ pressed steel terminals, switch box and making good the disturbed surface of wall/ floor etc to match with the existing surfaces of wall/ floor complete all as specified and directed. Note :- (i) If the contractor fail to make good the disturbed surface of wall/ floor etc and do not match with the existing surface of wall/ floor to the entire satisfaction of Engr-in-Charge, a recovery of @ Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute, the decision of Accepting Officer will be final and binding. (ii) Old fittings/ fixtures / accessories like switches, sockets, lamp holders, regulators etc., if found in serviceable condition shall be removed carefully for reuse in the work or taking on charge. (iii) Only old unserviceable items will be considered in credit Sch.

M&L for point wiring with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 Sqmm multi stranded copper conductor cable (FRLSH) with continious earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed, drawn in and including concealed PVC conduit "medium grade" (ISI marked), not less than 20mm dia duly concealed on wall/ ceiling or above false ceiling with fittings medium grade (Color coding of wires shall be phase, neutral and earth wire all as specified) sunk metal flush box with and including decorative polycarbonate frame for housing modular switches, sockets, fan regulators etc including white cover plate complete all as specified and directed for following:- Note:- (i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface in CM (1:3) and matching with the existing surface deemed included in quoted rates. (ii) If the contractor fail to make good the disturbed surface of wall/ ceiling etc and do not match with the existing surface of wall/ceiling to the entire satisfaction of Engr-in-Charge a recovery of @ Rs. 50/- per RM will be made from payment due to the contractor. In case of any dispute the decision of Accepting Officer will be final and binding.

One light/fan/exhaust fan/call bell point controlled by one way 5 Amp switch.

One 5 pin socket out let 5/6 Amp on independent board.

One 5 pin socket out let 5/6 Amp on same board.

One light point controlled by two way 5 Amp switch.

Descrition same all as per item No 125 above, but with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point complete all as specified & directed.

S&F modular switch piano, 1module, flush type button 5/6 Amp single pole one way conforming to IS: 3854 and ISI marked complete all as specified and directed. Make: Legrand cat No: 6734 01/ Indoasian Cat No: 800000/ Havells Cat Part No: ACWSXXW101

S&F modular switch piano, 1module, flush type button 15/16 Amp single pole one way conforming to IS: 3854 and ISI marked complete all as specified and directed. Make: Legrand cat No: 6734 11/ Indoasian Cat No: 800002/ Havells Cat Part No: ACWSXXW161.

S&F modular socket outlet, 2 module, five pin 2 in 1, 5 Amps, flush type, 230 volts AC circuit complete all as specified and directed. Make: Legrand cat No: 6734 52/ Indoasian Cat No: 800020/ Havells Cat Part No: ACWKPXW063

S&F modular socket outlet, 2 module, five pin 2 in1, 15 Amps, flush type, 230 volts AC circuit complete all as specified and directed. Make: Legrand cat No: 6734 55/ Indoasian Cat No: 800022/ Havells Cat Part No: ACWKCXW163.

S&F modular switch piano, 1module, flush type button 5/6 Amp single pole two way conforming to IS: 3854 and ISI marked complete all as specified and directed. Make: Legrand Cat No: 6734 02/ Indoasian Cat No: 800001/ Havells Cat Part No. ACWSXXW102.

S&F modular switch bell push button type, 1module, 6 Amp single pole complete all as specified and as directed. Make – Legrand cat No: 6734 04/ Indoasian Cat No: 800007/ Havells Cat Part No. ACWSBXW101.

S&F crown shaped post top lantern fitting in soothing moon finish made up of polycarbonate including 20W retrofit LED lamp with B-22 base complete all as specified and directed. Make: Havells Cat No: ATHENA 3 (MOON) or equivalent others make as specified.

S&F ceiling rose surface bakelite 65 x 25mm dia three terminals (ISI Marked) complete all as specified and directed. Make – Anchor Jumbo Code-39050 / 3224 or equivalent of make as specified.

S&F bell electric DING DONG type, AC, 230V single pole complete all as specified and as directed. Make – Legrand cat No: 5734 43 or equivalent make as specified.

S&F angle Lamp holder (with metal ring), insulated body, of PVC/ Polycorbonate with back plate (ISI Marked) suitable for batten fitting with and including one No. 10 watt conventional type LED bulb temp 6500K and lumen out put 950 complete all as specified and as directed. Make– Anchor, Code-39797 or equivalent others make as specified.

S&F sub main wiring alongwith earth wire (green colour) with single core FRLSH, PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (medium grade) with standard accessories and earth wire connected with main earth dolly, of the following sizes of cable & dia of conduit complete all as specified and directed:- NOTE :- (i) Two/four run of single core FRLSH PVC cable with one/two run of earth conductor and conduit shall be measured as one unit (RM). (ii) The quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc of any description for concealing the conduits to required depth & making good the disturbed surface in CM (1:3) including finishing the surface to match with the existing surface. The portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using PVC rawal plugs.

2x6 Sqmm + 1x6 Sqmm earth wire with PVC conduit 20mm dia

S&F surface mounted LED luminiare, 20 watt with all accessories having polymer extruded channel with diffuser for glare free light, high lumen output, driver PF >0.98 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circuit protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >120 lumen per watt, internally pre-wired through flexible wire connecting with ceiling rose complete all as specified and directed. Make :- Shakti, Model: SZSLBMX020 / Crompton, Cat No LCTLN-20-CDL / Havells, Cat No LHEXACP7FN1W020. Note: The firm has to give warranty for fitting including driver minimum for 2 years for any defects developed during the period.

S&F LED building security light 1 x 20 W housing made out of pressure die-cast aluminium alloy with toughned glass, IP 66 protection working on 240 volts, 50 Hz, consisting of reflecting lamps wired with appropriate driver PF> 0.98 having overvoltage protection upto 440 volt, surge protection level > 10 KV, thermal short circuit prtection THD< 10% made up of long life LED chip (SMD) in modular with Ra< 70, and LED lumen efficiency > 140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive wway, 80 degree luminaire efficiciency> 120 luminous /watt power LED should be of more than 01 watt CCT should be between 5700° K- 6500 K with and including fixing on bracket of 32mm GI tubing (medium grade) of 1.2m long bent to suitable shape with two nos of MS clamp of suitable size including connecting with 1.5 sqmm , 3 core, PVC insulated copper onductor cable 1100 Volt grade from distribution box to light complete all as specified and directed. Make :- Shakti Cat No SZPCLPM020 / Havells Cat No: LHEXAYP7PN6K020 / Crompton Cat No:TRP-400-20-57-LM-NSR Note :- (i) The firm has to given warranty of street light fittings including driver minimum for 03 years for any defect developed during the period. (ii) The contractor Shall submitt the third Party LM 79 report from any NABL approved laboratory. (iii) The fiitting should have BIS, CRS No(iv) Connection to luminaire shall be done in suitable PVC connector within the bracket/luminaire end and are inclusive in above.

S&F LED tube light fitting 10 watt, mirror type with high output diffuser 02 feet with ploycarbonate diffuser & integrated electronic driver, 240 volts, 50 Hz suitable to fix on surface, having suitable size drivers and all other connected accessories internally pre-wired and connecting up with suitable size copper cable three core of required length complete all as specified and directed. Make : Shakti, Cat No. SZSLAMX010 or equivalent of other make as specified.

Disconnecting and taking out existing old LT cable of any size from trenches/from pole/walls including taking out old GI tubes, cable protection covers, etc complete all as specified and directed.

Supplying, laying, commisioning and testing of 1.1 KV grade XLPE insulated, PVC sheathed, steel armoured, aluminum stranded conductor LT UG cable (Conforming to IS 7098), ISI marked, in trenches / ducts / through GI pipes under roads of following size complete all as specified and directed:- Note:- 1. The earth work, GI pipe shall be measured and paid sepretely. 2. Cable may fixing/ passing through pipe laid in trenches or fixed to pole/ wall or fixed to LT panel etc.

16 Sqmm, 4 core.

16 Sqmm, 2 core.

M&L for sand cushioning with dry and clean fine river sand for underground cable 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cable complete all as specified and directed. Note:- Punned thickness shall be considered for payment purpose.

Supply and laying cable protection bricks, common burnt clay sub class 'B' designation 75 for protection of UG cable laid in trenches with axis of the bricks perpendicular to the axis of the cable complete all as specified and directed.

S&F galvanized steel water tubing (GI Pipe) light grade (ISI marked) with all fittings as in sleeving for cable protection & laid in trenches/ floor or fixed to wall, ceiling and pole of following bore complete as specified and directed :- Note : MS Clamp, nut bolts and washer shall be measured and paid seperatly for fixing with pole etc.

40mm bore

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground, earth pit not less than 2.25 mtr depth below ground level at any type of strata with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate, connected by 4 mm GI wire as earth lead by means of brass nuts and bolt, thimbles check nuts, washers including concrete chamber of PCC (1:3:6) type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM (1:4) funnel with wire mesh, RCC pit cover of 320 x 320 x 80mm size PCC (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion complete all as specified and directed. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick reinforced with XPM weighing not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

S&F connecting & testing distribution board of sheet metal enclosures double door, IP-43, 240V, for using MCBs / MCB isolators with having tinted copper bus bars suitable for 200 Amps rating having following capacity complete all as specified and directed:-

DB SPN, 8 way Make :-Legrand Cat Part No- 5076 11 or equivalent others make as specified.

DB SPN, 12 way Make :-Legrand Cat Part No- 5076 12 or equivalent others make as specified.

S&F connecting & testing distribution board of sheet metal enclosures double door, IP-43, 415V, for using MCBs / MCB isolators with having tinted copper bus bars suitable for 200 Amps rating having following capacity complete all as specified and directed:-

DB TPN, 4 way Make : Legrand Cat Part No. 5076 70 or equivalent others make as specified.

S&F connecting & testing MCB, 230V/ 415V with rupturing capacity 10 KA of following capacity complete all as specified and directed:-

MCB 6 to 32 Amp, SP, 'B' series/ curve, Make :- Legrand, Cat Part No 4024 31 to 4024 36 or equivalent others make as specified.

MCB 40 to 63 Amp, SPN, 'C' series/ curve, Make :- Legrand, Cat Part No 4086 18 to 4086 20 or equivalent others make as specified.

MCB 40 to 63 Amp, TPN, 'C' series/ curve, Make :- Legrand, Cat Part No 4086 81 to 4086 83 or equivalent others make as specified.

S&F exhaust fan with louver shutter, heavy duty, AC, single phase, 230 V, of size 300 mm sweep, 900 RPM and connecting up including provision of cable from ceiling rose/ connector to exhaust fan with and including making holes, grouting of nuts, bolts etc and making good the disturbed surface of wall complete all as specified and directed.

Hindustan Co.Co

M/S SURAT SINGH AND SONS

M/S VIJAY TRADERS

sidh builders

SA construction co.

RAMAPATI ENGINEERING SERVICES