REPAIR TO ROOF SHEETING JOINERY SANITARY FITTINGS FLOORING PLASTERING ROOF TREATMENT AND OTHER MISC WKS IN OTM AND MD ACCN OF ZONE A AND B AT PALAMPUR MIL STN

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n. exc. 1.5 sq.m each complete all as specified and directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) exc 1.5 sq.m but n. exc 4 sq.m each, complete all as specified and directed.

Taking down shutter of any description exc 1 sq.m but n. exc 2 sq.m each. complete all as specified and directed.

Taking down cement plaster including tiles of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Rendering 15mm thick plaster on fair faces of brick work/stone masonry or other than fair faces of brick wall in CM 1:6, finished the surface even and fair without using extra cement complete all as specified and directed. Note: WPC compound may be used as per required ground condition which is to be measured and paid separately.

Rendering 15mm thick plaster on fair faces of brick work/stone masonry , concrete surface in CM 1:4, finished the surface even and smooth without using extra cement complete all as specified and directed.

Rendering 5mm thick plaster on ceiling in CM 1:3 finished the surface even and fair without using extra cement complete all as specified and directed.

Preparation of newly plastered or unplastered surfaces of walls and applying two coats of Oil bound distemper, of approved tinted, over 2mm thick wall care putty complete all as specified and directed.

Preparation of newly plastered or unplastered surfaces of walls and applying two coats of white wash complete all as specified and directed.

Preparation of newly plastered or unplastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

M&L preparation of new plastered ceiling surface and applying two coats of white wash, complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facing, dressed stone work precast concrete articles complete all as specified and directed.

M&L walling of random rubble, un-courses, well bonded bedded & solidly hearted built in cement mortar 1:6, complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6, complete all as specified and directed.

Demolition of cement concrete unreinforced in ground floors, kota stone, granite flooring, tiles flooring and pavings not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed.

Dismantling of wall & ceiling boards (fiber, pulp, insulation etc) or insulation boards /slabs /blankets any thickness, including cover fillets complete all as specified and directed.

Dismantling timber scantlings 40Sq.cm and over in section, in any position framed or unframed work complete all as specified and directed.

Dismantling timber scantlings like fillets,rails, posts,rafters,purlins,etc under 40Sq.cm in section, in any position complete all as specified and directed.

M & L second class soft-wood plain fillets square or rectangular in sections bull-nosed splayed, rounded on one edge or face area exc 6 sq.cm but not exc. 13 sq.cm secured with nails or brads complete all as specified & directed.

S&F 6mm thick E-board (Classic) false ceiling of size 610mm x 610mm fixed with GI snap grid frame work of same size as GI tee of size 25x25x1.25mm as main runner, 25x25x1.25mm thick GI tee as cross runner and GI angle of size 25x25x1.25mm at the perimeter, including 4mm GI adjustable suspender of required length, including dismantling of old ceiling complete all as specified and directed.

S&F in repairs 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed.

S&F hollow PVC wall lining consisting of 5mm thick wood grain printed PVC sheet used instead of plain colour sheet inclusive of solvent cmeent and fixing at site on PVC frame as per specification and drawing (or without PVC frame work), fixed in repair complete all as specified and directed.

M&L 75 mm thick PCC (1:3:6) type C-2 using 40 mm graded crushed stone aggregate laid in alternative bays area not exc 2 sqm each as in plinth protection laid to slope of 1 in 12 including finishing the surface even & smooth without using extra cement complete all as specified & directed.

M&L 25 mm thick PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) 25mm thick as in sub base of floor/path surfaces finished the surface even & rough to receive floor finishes complete all as specified and directed.

M&L Non-skid, coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:4, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles complete all as specified and directed.

M&L Non-skid, coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.18 sqm but not exc 0.38 sqm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:4, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles complete all as specified and directed.

M&L Non-skid, coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.18 sqm but not exc 0.38 sqm cut to size as required as in skirting/dado over and including 10mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles including dismantling complete all as specified and directed.

M&L Vitrified Ceramic tiles 10mm thick (square / rectangular) light shade polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15 mm thick screed bed or bedding layer in CM 1:4 complete all as specified.

M&L Vitrified Ceramic tiles 10mm thick (square / rectangular) light shade polished, area of each tiles not exceeding 0.36 sqm, in skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 10 mm thick backing coat in CM 1:4 complete all as specified.

M&L Glazed ceramic coloured tiles in vertical surface 350mm x 250mm x 7mm/450mm x 350mm x 7mm/450x300x7mm/600x300x7mm thick set and jointed in neat cement slurry, pointed in white or coloured cement to match the colour of tiles, over and including 10mm thick backing coat in CM 1:4 to receive tiles, including dismantling complete all as specified and directed.

S&F Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer, complete all as specified and directed.

S&F pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer,complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer composite) solid decorative type flush door shutter (galzed or skelton) of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension grade) calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/cum and screw withdrawal strength of 1800N (face) & 900N (edge) minimum compressive strength 50 N/mm2 , modules of elasticity 850 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be lamnated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhessive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screw, (incl wiremesh required) compelte all as specified and directed.

S&F box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick MS tube factory made with double side shutters wire gauged shutters & glass glazed shutter(wire and glass panes shall be measured and paid separately) with side hung shutters with steel handles and steel peg stay dovetailed to welded incl 2 Nos tower bolts 150 mm long for each leaf and 10 mm square bar grills at spacing as shown on drg welded to FI 40x5m frame work, incl other fittings,hinges,handles tarred hold fast PCC blocks etc. all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 ,complete all as specified.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying and fixing in opening as per specifications & directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat molded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified & directed.

S&F in repairs 100 mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F in repairs 75 mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F in repairs 150 mm size (length of bolt) aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F in repairs 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repairs 300 mm size (length of bolt) aluminium alloy, anodised, sliding door bolt with hasp and staple ,(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F in repairs 300mm long mild steel ordinary Hellical door spring rod pattern springs including roller and roller plate complete all as specified and directed.

M&L preparing new surface of steel of any description, over 10cm width or girth not other wise described and appliying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed.

Prepartion of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

S&F rolled mild steel bands,straps,supports or stays for rainwater,ventilating pipes,including bolts,if required; hooks(stays),heavy,for large gates,hook and pintle hinges;large hasps and staples;chains;hand made sliding bolts;clamps;hold fasts;wall ties;hooks for hanging fans;plain angle cleats for securing purlines to wooder trusses conform to Fe-290 Gde E-165 complete all as specified & directed.

M&L plain cement concrete 1:2:4 type B-0 using 12.50 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed.

M&L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed.

Dismantling boarding, any description, fixed in any position with nails complete as specified and directed.

S&F in repairs 18mm thick lead free factory made, 100% solid WPC (Wood polymer composite) sheet for cupboard/kitchen cabinet shutters and frames having high natural fibre content 25 to 30% wood colour sheets with density not less than 500 Kg/cum and the weight of sheet of 1 Sqm should be 11 Kg (+/- 5%) manufactured by IS 9001: 2015 certified company the should should be 100% water proof, termite proof, fire retardant, manufactureed by single layer extrusion process with excellent screw, fixed with screws to timber/steel frame work complete all as specified and directed.

S&F in repairs 75mm size, hasp and staple safety type aluminium anodised with mild steel, hinge pin including bolt to hinge plate and fixed with screws all as directed.

S&F in repairs mild steel continuous piano hinges, bright finish or electro galvanised, width of flap when open 40mm, complete all as specified and directed.

S&F in repairs 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including fixing fittings such as GI nipple for inlet, outlet, washout and overflow etc, including 20mm size ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe including dismantling complete all as specified and directed.

S&F in repairs 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including fixing fittings such as GI nipple for inlet, outlet, washout and overflow etc, including 20mm size ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe including dismantling of tank complete all as specified and directed.

Disconnecting existing tanks of capacity 250/500 ltrs setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning and removing all scale and dirt,etc,from tanks and from moulds of circulating pipe,etc complete all as specified and directed.

S&F vitreous chinaware squatting pan, 'Orissa pattern' size 580mm x 440mm, with cast iron 'P' or 'S' trap, front or back inlet, integral foot rest with provision of PCC M-15, type B-1 using 20mm graded crushed stone aggregate complete all as specified, incl making connections to trap and to flush pipe etc and making good to floors to match existing, in repair, complete all as specified and directed.

S&F in repair vitreous china white/coloured wash down water closet pan (Padestal Pattern), including connection to flush pipe, 'P' or 'S' trap, with fixing bolts PVC seat cover with chromium plated mild steel hinges device (excluding flushing cistern and flush pipe) with SWR gully trap, complete all as specified and directed.

S&F in repairs CP jet spray hygenic spray jet 15mm bore dia fittings 1 to 1.5m long tube acrylic type complete all as specified and directed.

M&L 10 litres capacity PVC, low level, valveless, syphonic action type flushing cistern, inlet ball valve, float valve, handle and fixing arrangement, 32mm dia PVC flushing pipe and 15mm dia, 600mm long PVC connection with CP brass coupling nuts and PVC washer at both ends (fixed in repair), complete all as specified and directed.

S&F Vitreous china, wash hand basin, (white/coloured) of size 550mm x 400mm including brass CP waste coupling 32mm size with long screwed shank and fly nuts, PVC medium grade 32mm dia waste pipe, chain and plug, porcelain stopper , PVC connection 15mm dia, 450mm long with brass CP nuts and washers at both ends (fixed in repair), complete all as specified and directed.

S&F in repair vitreous china half staff urinal flat back, size 465x355x265mm white (minimum), including grating and union for discharge pipe excluding flushing cistern, flush pipe and waste pipe, complete including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing, flush pipe grating and ujnion for discharge pipe, incl urinal spreader complete all as specified and directed.

S&F 32mm bore low density polyethylene (LDPE) pipes of pressure rating 6 Kgf/sq.cm for low level cistern and waste pipe for sink, washbasin complete all as specified and directed.

S&F in repairs, fancy type, pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' & 'Cold' with long screwed shanks and fly nuts, screwed for 15 mm bore iron pipe complete all as specified & directed.

S&F in repairs, fancy type, long body bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed.

S&F fancy type, chromium plated, bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed.

S&F in repairs stop valve/angle valve, fancy type, cast copper alloy, screwed down, high pressure, with quarter turn flange, screwed both ends for 15 mm bore iron pipe or for union complete all as specified & directed.

S&F in repairs PVC connection 15mm size, 600mm long with PTMT nuts complete all as specified and directed.

S&F in repairs ball brass valves, high pressure, with polythene float and fly nut complete, screwed for 20 mm bore iron pipe or brass ferrule complete all as specified & directed.

S&F in repairs 32/40mm bore waste fitings, brass, chromium plated for glazed ware sinks, basins etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repair 32mm waste coupling of PTMT (half or full threaded) minimum weight 32mm-45gms/40mm-60 gms) complete all as specified and directed.

S&F in repair 40mm waste coupling of PTMT (half or full threaded) minimum weight 32mm-45gms/40mm-60 gms) complete all as specified and directed.

S&F in repairs brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed.

S&F centre hole bras chromium plated wall mixture for mixing hot and cold water, screwed down for iron pipe for 15mm dia pipe, complete all as specified and directed.

S&F brass chromium plated sink mixture for mixing hot and cold water for sink, screwed down for iron pipe for 15mm dia pipe, complete all as specified and directed.

S&F in repair chromium plated central hole basin mixer for WHB single lever without popup waste system with 450mm long braided hoses complete all as specified and directed.

S&F in repair plastic water closet seat cover, cream/white colour, closed pattern with flat botom and cover and mild steel chromium plated aluminium hinging device for pedestal pattern WC complete all as specified and directed.

S&F in repair plastic Anglo Indian water closet seat cover, cream/white colour, closed pattern with flat bottom and cover and mild steel chromium plated aluminium hinging device for pedestal pattern WC complete all as specified and directed.

S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete al as specified and directed.

S&F in repair brass chromium plated shower rose 125mm size, with or without swivel joints, including shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour, fixing to steel pipe or union complete all as specified and directed.

Dismantling 100/110mm bore dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenchese, taking out from walls incl clamps, if required complete all as specified and directed.

Dismantling 75mm bore dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, taking out from walls incl clamps, if required complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to walls with stack clamps,complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, as in floor and trenches complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to walls with stack clamps,complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, as in floor and trenches complete all as specified and directed.

S&F in repairs 110mm bore, PVC (SWR) junction, (single T) equal or unequal with access door complete all as specified.

S&F in repairs 75mm bore PVC (SWR) junction, (single T) equal or unequal with access door complete all as specified and directed.

M&L 75 mm size PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 complete including taking down old unserviceable floor trap complete all as specified & directed.

M&L 100/110 mm size PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 complete including taking down old unserviceable floor trap complete all as specified & directed.

S&F in repairs 75mm bore PVC (SWR) bends with access door of any radius complete all as specified and directed.

S&F in repairs 100/110mm bore PVC (SWR) bends with access door of any radius complete all as specified and directed.

S&F in repairs soap dish stainless steel, approximate size 160mm x 160mm x 90mm fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repairs towel rail 600mm long 20mm dia, D type brass chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 170 gms) complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specifed and directed.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site complete all as specified and directed.

S&F in repairs steel water tubing, 15 mm bore, galvanised , "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work in required etc, complete all as specified and directed.

Fixing only steel water tubing, 15 mm bore, galvanised , "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work in required etc, complete all as specified and directed. Note: The GI tubing obtained from taking down used in this item.

S&F in repairs steel water tubing, 20 mm bore, galvanised , "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work in required etc, complete all as specified and directed.

Fixing only steel water tubing, 20 mm bore, galvanised , "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work in required etc, complete all as specified and directed. Note: The GI tubing obtained from taking down used in this item.

Dismantling old plain or corrugated rusted steel sheeting, any gauge and thickness in roof covering including Nainital or similar pattern roof coverings, complete all as specified and directed.

S&F 0.63mm Galvanised,corrugated mild steel sheeting with two corrugations side lap,fixed with L-type or J-type or cranked hook bolts and washers in roofs,walls etc. with grade of zinc coating 275 complete all as specified and directed.

Fixing only 0.63mm Galvanised,corrugated mild steel sheeting with two corrugations side lap,fixed with L-type or J-type or cranked hook bolts and washers in roofs,walls etc. with grade of zinc coating 275 complete all as specified and directed. Note: The sheet obtained from dismantling used in this item.

S&F 0.80 mm thick plain, galvanised mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified & directed.

S&F pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, compete all as specified and directed. (Colour as approved by GE)

M&L pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, facia and fixed with self tapping screws as specified. (Colour as approved by GE)

S&F in repairs anodised aluminium frame for doors, windows, ventilators with minimum thickness of powder coating 50 micron with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Powder coated Anodised aluminium door shutters (minmium thickness of powder coating 50 micron), aluminium section of bottom rail 114.50x44.45mm, middle and top rail 85x44.45mm, style 85x44.45 mm and thickness of section not less than 3mm , weight of glazing clip not less than 0.124 Kg/m including necessary joining cleats, glazing clips, rubber neoprane packing two number of alumium handle 150mm long for each shutter, one aluminium door stopper, hinges type B-21,100mm long,anodised aluminium snap beading,screws,anodised aluminium fittings complete all as specified and directed.

S&F Powder coated Anodised aluminium window and ventilator shutters (minmium thickness of powder coating 50 micron), weight of aluminium section not less than 0.914 kg/m for style and rail, weight of glazing clip not less than 0.124 Kg/m including necessary joining cleats, glazing clips, rubber neoprane packing,anodised aluminium snap beading,screws,anodised aluminium fittings such as peg stays one number,hinges type B-21, 100 mm long two numbers,suitable handle one number on each shutter complete all as specified and directed.

Taking down and refixing the same aluminium door shutter after resecuring/readjusted to aluminium section weighing not less t han 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handle 2 Nos in each door, hinges, anodised aluminium snap bidding, screw etc and renew unserviceable items such as fittings, sections, glass, solid PVC sheets etc complete all as specified and directed.

S&F in repairs 4mm thick sheet glass, ordinary quality and glazing in aluminium frame in square n exc. 0.5 sq.m in each pane complete all as specified and as directed.

Hacking out old broken glasses (any thickness, size, quality or description) from wooden frames or steel frames, glazed with putty or fixed with wooden beads, complete all as specified.

S&F in repairs 3mm thick transparent fibre glass, ordinary quality as in glazing n exc. 0.5 sq.m in each pane fixed in wood steel frames with oil putty or wooden beads or self tapping screw complete all as specified and as directed.

S&F in repairs 3mm thick figured glass, pin head type and glazing with oil putty in squares n.exc. 0.50 sq.m in each pane, complete all as specified and directed.

S&F in repairs brass 4 Levers mortice lock, vertical type of size 100mm, complete all as specified and directed.

S&F brass 4 Levers mortice lock, vertical type of size 100mm, complete all as specified and directed.

M&L in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified and directed.

S&F aluminium (extruded section body) door closer hydraulically regulated, designation No. 3 universal type suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as specified and directed.

S&F in repairs aluminium (extruded section body) door coser hydraulically regulated, designation No. 3 universal type suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as specified and directed.

M&L rolled sections (like beams, channels, angles, flats or other type of sections) Fe-410-W (Gde-E-250) quality-B as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. complete all as specified and directed.

S&F PVC coated mild steel conduit pipe 25mm dia (Drapery rod) including with PVC coated MS clamps to hold drapary rod and decorative attachment at one or both ends of drapary rod complete all as specified & directed.

S&F in repairs stainless steel sink with drain board, 1mm thick for kitchen or laboratory with plug, waste pipe washers including contilever cast iron brackets, connecting union, coupling etc overall size 915x460mm with bowl size 410x330x160mm complete all as specified and directed.

M&L preparing surface of sunken slab in toilet flooring and applying 15mm thick plaster in CM 1:4 with integral water proofing compound both on floor and wall, including, laying and testing of bituminous coating system based on bituminous emulsion, including application of one coat of primer and laying of APP membrane as per manufacturer specification in sunken portion with and including sunken floor shall be filled with brick concrete 1:4:8 as per existing thickness, a pipe of dia 40mm, 600mm long GI spout incl fitting in floor and incl demolition of floor complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L preparation of old/untreated walls (washing, rubbing down and stopping of distempered and painted surfaces) and finishing walls with textured exterior paint of required shade, granular finish, New work (Two or more coats applied @ 3.28 ltr/10 Sqm) over and including priming coat of exterior primer applied @ 2.20Kg/10 Sqm over 1mm thick putty over plastered surface to prepare the surface even and smooth complete all as specified and directed. Note: Shade as approved by GE/Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not other wise provided for complete all as specified and directed.

S&F compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. Fe-410 W(Gde-E-250) quality-B, complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.

S&F mild steel joist, channel, angle or tee sections, fixed independently, without connecting plates etc. gde Fe 410-W (Grade E-250) quality B complete all as specified and directed.

M&L granite (of any size) tile 18 to 20mm thick machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over 20mm thick screed bed in CM 1:6 including cutting and polishing complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L laying chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment over 20mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 50mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base etc. finished the surface even and smooth without using extra cement complete all as specified and directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size /shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete including demolition of existing tiles and removing outside the MoD land complete all as specified and directed.

S&F stainless steel peg set of Six pegs, fixed/welded/soldered on stainless steel base plate of size 300x30x2.5mm and fixed with stainless steel screws, rowel plugs as per sample approved by the Engineer-in-Charge complete all as specified and directed.

S&F in repairs door seal (snake guard) with aluminium frame powder coated upto 900 to 1000mm door opening complete all as specified and directed.

S&F in repair glass self assembly consisting of 5.5mm thick glass sheet glass self 12cm wide with CP bracket guard and railing 60cm long complete all as specified and directed.

S&F 32mm PVC waste pipe to WHB, sink etc complete all as specified and directed.

M/s ASS Construction Co (BID ID -3331455)