WBMAD/ULB/HM/APAS-12 (2025-26)

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm. (P.No.1, T/2(a)

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc.layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) (P.No.1, T/3(a) (a) With earth obtained from excavation of foundation.

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. (P.14, T/1)

(I) Cement concrete with graded stone ballast (40 mm size excluding shuttering) In ground floor (A) [Pakur Variety] (a) 1:3:6 proportion P.no. 34, T/22) 3rd corrigenda, (a) 1:3:6 proportion

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. P.no. 16, I.T/16)

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) (When the height of a particular floor is more than 4 m the equivalent floor height shall be taken as 4 m and extra for works beyond the initial 4 m ht. shall be allowed under 12 (e) for every 4 m or part thereof) P.no. 42, T/36 a) (f) 25 mm to 30 mm shuttering without staging in foundation

(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In- Charge.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups,binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape,placing in proper position and binding with 16 gauge black annealed wire at every inter-section, complete as per drawing and direction. a) For works in foundation and upto roof of ground floor/upto 4 m (P-43, T/40)

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (a) Pakur/Chandil variety. (P.No.26 T/10(i)), 3rd corrigenda, rate annalisis

M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one her with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 Kg. / m. or 15 % of weight for finished structal members weighing less than 22.5 Kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of Engineer In Charge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the rate for each additional floor or 4m. beyond initiial 8m. or part thereof.

I) For structural members of specified sections weighing less than 22.5 Kg./m P.no. 99, T/1), 3rd corrigenda,

Supplying, fitting, fixing G.I chain link fencing 75 mm x 75 mm mesh 12 g wire to the R.C.C or wooden posts with galvanised hooks or staples etc. complete as per direction. (P.No.221, T/10 )

(a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. (P.No.104, T/13(i) ) 3rd corrigenda, ii) Grill weighing above 16 Kg./sq.mtr and above

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding /staging where necessary .[Excluding cost of chipping over concrete surface] A) In Ground floor (P-189, T-1) 3rd corrigenda, (a )With 1:6 cement mortar (b) 20 mm thick plaster (Inside plaster)

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (P-64, T/35) (B) Wal With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (b) Area of each tile above 0.09 Sq.m (i) Coloured decorative

a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. (P.200, T/1 (a) (b))

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (P.14, T/1) (b) On steel or other metal surface : With super gloss (hi-gloss) (ii) Two coats (white in shade)

Supplying Fitting and Fixing 2 in 1 Sea Saw, Total Length of SeaSaw: 8 feet Total Width of SeaSaw: 4 feet Material Used: GI Iron and FRP made slider Thickness of Iron: 2.5mm Quality of Iron Used: Tata or Bhushan Finishing of Slider: Smooth finishing with Gel Quote paint Iron Structure finishing: Smooth Paint Quality: NC Duco paint with UV clear lacquer Weight Can with Carry: 35kg to 40kg with carring, instalation materials & labour 2 in 1 Sea Saw QUOTATION RATE

Supplying Fitting and Fixing Slider, Length of Slider: 12 feet Height at the shooting point: 6 feet Slider Type: Straight Material Used: GI Iron and FRP made slider Thickness of Iron: 2.5mm Quality of Iron Used: Tata or Bhushan Finishing of Slider: Smooth finishing with Gel Quote paint Iron Structure finishing: Smooth Paint Quality: NC Duco paint with UV clear lacquer Weight Can Carry: 40kg to 45kg with carring, instalation materials & labour 12 feet length Slider QUOTATION RATE

Supplying Fitting and Fixing 2 in 1 Swing, Height of Swing: 7 feet Length of Swing: 8 feet Material Used: GI Iron and FRP made seats Thickness of Iron: 2.5mm Finishing of Seats: Smooth and Gel quote Iron structure Finishing: Smooth Quality of Iron Used: Tata or Bhushan Paint Quality: NC Duco paint with UV clear lacquer Weight Can Carry: 35kg to 40kg, with carring, instalation materials & labour 2 in 1 Swing QUOTATION RATE

Add GST @ 18%

Add Cess 1%