Procurement and Installation of New HVAC System at GST Council Secretariat, 5th Floor, Tower-II, Jeevan Bharti Building, Connaught Place, New Delhi

5 Total amount ₹ 7,131,131.10

municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of

Engineer-in-charge. 49,410.00

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing and

fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized

with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle

cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre

to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with

6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required

length with nuts & bolts of required size and other end of angle hanger fixed with

intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre,

to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26

mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction

perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x

230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27

mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to

wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws

@ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel

with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and

finishing to a flush finish of tapered and square edges of the board with recommended

jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto

150 mm on both sides of joint and two coats of primer suitable for board, all as per

manufacturer's specification and also including the cost of making openings for light fittings,

grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as

per drawings, specification and direction of the Engineer in Charge but excluding the cost of

Digitally signed by MANISH

12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board

with BIS certification marks) sqm 300 1355.80 406740

Providing the gypsum single sided cove of 150mm x 150mm having a facia of 75mm to macth

the specifications same as gypsum ceiling. Rm 150 300.00 45000

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of

approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%,

Light Reflectance ≥ 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as

per (BS 476 pt - 6 &7)in true horizont al level suspended on interlocking T-Grid of hot dipped

all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main

T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and

secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of

size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm)

50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger

rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm

centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the

help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be

fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry

wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support

system shall be pre-painted with polyester baked paint, for all heights. The work shall be

carried out as per specifications, drawings and as per directions of the engineer-in-charge

26.27.1 With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.60) sqm 300 2333.60 700080

Providing and fixing aluminium work for doors, windows, ventilators and partitions with

extruded built up standard tubular sections/ appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia

and size, including necessary filling up the gaps at

21.1 junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.

Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically

wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.

brass / stainless steel screws, all complete as per architectural drawings and the directions of

Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

21.1.1For fixed portion

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50

8724 12 mm thick marine plywood conforming to IS: 710 Sqm 150 785.00 117750

4MM THICK MDF BOARD: Providing and fixing plain lining with necessary screws/ nuts & bolts/

nails, including a coat of approved primer on one face, and fixed on wooden/ steel frame

MR work, complete as per direction of Engineer-in-Charge

Digitally signed by MANISH

4mm thick MDF Board Sqm 150 250.00 37500

LAMINATE: Providing & Fixing decorative high pressure laminated sheet of plain

/ wood grain in gloss / matt/ suede finish with high density protective surface

layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type

9.127.2 S, including cost of adhesive of approved quality. 1MM THICK Sqm 150 897.30 134595

Providing and fixing thermal insulation with Resin bonded rock wool conforming to IS: 8183,

12.61 density 48 kg/m3, 50 mm thick, wrapped in 200 G virgin Polythene bags placed over existing

false ceilng and held in position by criss-crossing Gl wire.. Sqm 150 316.05 47407.5

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to

prepare the surface even and smooth complete Sqm 500 262.70 131350

Applying priming coats with primer of approved brand and manufacture, having low VOC

(Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50

grams/litre 500 73.95 36975

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile

Organic Compound) content less than 50 grams/ litre of approved brand and manufacture,

including applying additional coats wherever required to achieve even shade and colour

Providing and applying cement plaster. 12mm cement plaster of mix 1 : 6 (1 cement : 6 coarse

Total Amount B 1,972,717.50 82,500.00

Total Amount B 1,972,717.50 82,500.00

Labour cess factor as per CPWD @0.973 1,919,454.13

Cost index factor @103 1,977,037.75

Total Amount B 1,977,037.75 82,500.00

Total Amount B 1,977,037.75 82,500.00

Electrical (Repair and replacement) as an where basis

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core cable in surface / recessed medium class

1.10 PVC conduit, with modular switch, modular plate, suitable GI box and earthing the

point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell

point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper

1.55 conductor single core cable in surface/ recessed PVC conduit, and earthing the point

with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS

1.14 PVC insulated copper conductor, single core cable in surface/ recessed medium class

PVC conduit as required.

Digitally signed by MANISH

1.14.1 2X1.5sq.mm-+ 1X 1.5 sq. mm earth wire Mtr 300.00 267.00 80100

1.14.3 2X4sq.mm+1X4sq. mm earth wire Mtr 150.00 373.00 55950

Supplying and fixing following modular switch/ socket on the existing modular plate &

switch box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 A socket outlet Each 25.00 136.00 3400

1.24.5 6 pin 15/16 A socket outlet Each 40.00 219.00 8760

1.24.7 TV antenna socket outlet Each 2.00 168.00 336

Supplying and fixing following size/ modules, GI box alongwith modular base & cover

plate for modular switches in recess etc. as required.

Supplying and fixing following Modular base & cover plate on existing modular metal

boxes etc. as required.

Supplying and fixing of following sizes of medium class PVC conduit along with

1.21 accessories in surface/recess including cutting the wall and making good the same in

case of recessed conduit as required.

1.21.1 20mm dia conduit mtr 35.00 151.00 5285

1.21.2 25mm dia conduit mtr 50.00 168.00 8400

8.3 LED Down lighter (SMD Type) (System lumen efficacy >135lm/Watt)

Digitally signed by MANISH

Supplying, Installation, Testing & Commissioning of LED Recessed/surface Down lighter

(Round /square/Rectangular) SMD type of following body material with PMMA and

prismatic diffuser and construction as per IS : 10322 with driver as per the requirement

with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz,

Operating temp range - 5 0C to 40 0C, internal surge protection of 2.5 KV with Short &

Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating)

< 19, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry),

life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life

ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K/ 4000°K /5700°K / 6500°K

(As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power

consumption should not more than the specified rating and Fixture shall be of relevant

BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing

on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR,

PVC insulated copper conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output. LM79 &

LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.

Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement.

(Thermal management: heat sink of aluminium housing such that LED junction

temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminium

Body including trim .

LED Down lighter (COB Type) (System lumen efficacy ≥105 < 120 lm/Watt ). Supplying,

installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/

Rectangular) COB Type of following body material and construction as per IS : 10322 with

driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt,

frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV

with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare

Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical

circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends,

CCT 3000°K / 4000°K / 5700°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color

Digitally signed by MANISH

LED Panel light 2x2 ft. (System lumen efficacy ≥105 <120 lm/Watt) Supplying, installation,

Testing & Commissioning of Panel light 2x2 ft., of following body material and construction

as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating

voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C,

internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P.

F.≥0.95, IP20, CRI >80,UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5

%), life time (LED, Driver

& electrical circuitry), of minimum 50000 Burning Hours with, 70% of initial Lumen

maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K /

4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3,

Maximum power consumption should not more than the specified

rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name

Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external

connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper

conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty.

System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing

required for LED fixtures as per BIS shall be submitted.

Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminium housing such that LED junction temperature shall not

8.6 rise above 90°C). Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm)

Total AMOUNT (C) ₹ 647,084.00 0

Total AMOUNT (C) ₹ 647,084.00 0

Digitally signed by MANISH