Construction of New Building For Farmer Training Centre at Panwadi, Tapi-Vyara Dist. Tapi

No figures

1 Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful 2453.00 Cumt 120.01

materials and disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft soil

2 Excavation for foundation upto 1.5 to 3 m depth including sorting out and stacking of 1580.00 Cumt 166.44

useful materials and disposing off the excavated stuff upto 50 Meter lead.(C) Dense or

3 Filling in foundation and plinth with sand in layers of 20 cm. Thickness including 162.00 Cumt 471.69

watering ramming and consolidating etc. comp.

thickness including ramming watering and consolidating etc. complete

5 Anti-Termite System:Providing and laying of permanent piping technology anti- 788.00 Sqmt 63.63

termite treatment before flooring work by installing LLDP (Low linear density

polyethylene) tube of 8 mm O.D. & 6.4 mm 1.D. with inbuilt pressure compensation

chip every 30 cm interval in the tube, having working pressure of 2 Kg/cm2 and

release rate of 1.9 Itr/hour fixed by P-clips and nails. The LLDP pipe shall be installed

at the entire periphery of the building and at internal network of building at a depth of

20 to 200 mm under floor at every 2 to 3 mtr. c/c distance (adjusted as per building

layout ) & Ends of loop pass through a PVC elbow of minimum 32 mm ID at junction

box of wall and floor level, entering into a steel reinforced grooved flexible pipe of

minimum 22 mm ID leading into junction box and the loops shall terminate in junction

boxes & test every junction during injecting chemicals for termite control treatment.

The anti termite chemical Imidacloprid 30.5% SC mix as per IS- 6313 (part III) shall be

injected by the pressure pump diluted with water @ 10.5 ml/5 ltr of water at the rate

of 2 Kg/sq.cm @ 5 Ltr/SMT. The contractor shall submit approved line plan for piping

system and junction boxes dully approved by Engineer-in-Charge with bond of 5 year

warranty.(II)Anti Termite chemical injected area (Chemical injecting incl. labour cost)

6 Filling available excavated earth (excluding rock) in trenches. plinth, sides of 2421.00 Cumt 133.65

foundations etc. in layers not exceeding 20 cm. in depth consolidating each disposited

layer by ramming and watering.

7 Providing and laying controlled cement concrete M.150 and curing complete including 365.00 Cumt 4007.51

the cost of formwork and excluding reinforcement for reinforced concrete work in (A)

Foundations and plinth pcc

8 Providing and laying controlled cement concrete M.250 and curing complete including 719.00 Cumt 4712.66

the cost of formwork and excluding reinforcement for reinforced concrete work in (A)

Foundations, footings, and Mass concrete. footing

9 Providing and laying controlled cement concrete M-250 and curing complete including 81.00 Cumt 7659.84

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in (d) columns Up to Plinth level.

10 Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6- machine cut 158.40 Cumt 3080.90

stone aggregates 40 mm nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

Item Rate In

Description of Item Quantity Unit Amount

No figures

11 Providing and laying controlled cement concrete M-200 and curing complete including 154.00 Cumt 7633.58

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in Columns, pillars posts and struts G.FLOOR and F.floor

12 Providing and laying controlled cement concrete M-200 and curing complete including 16.00 Cumt 7674.99

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in Columns, pillars posts and struts S.FLOOR

13 Providing and laying controlled cement concrete M-250 and curing complete including 184.50 Cumt 6077.17

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in Ground & Plinth BEAMS

14 Providing and laying controlled cement concrete M-150 and curing complete including 138.50 Cumt 5318.66

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in plinth Slab

15 Providing and laying controlled cement concrete M.200 and curing complete including 239.50 Cumt 6303.41

the cost of formwork and excluding reinforcement for reinforced concrete work in (C)

Ground floor Beams and First floor

16 Providing and laying controlled cement concrete M.200 and curing complete including 4.00 Cumt 6343.81

the cost of formwork and excluding reinforcement for reinforced concrete work in (C)

S.floor Beams,

17 Providing and laying controlled cement concrete M-200 and curing etc. complete 16.50 Cumt 6903.35

including the cost of form work and reinforcement for reinforced concrete work in (c)

Chhajja for Ground floor and first floor

18 Providing and laying controlled cement concrete M-200 and curing etc. complete 1.00 Cumt 6944.76

including the cost of form work and reinforcement for reinforced concrete work in (c)

Chhajja S.floor

19 Providing and laying controlled cement concrete M-200 and curing etc. complete 10.50 Cumt 8726.40

including the cost of form work and reinforcement for reinforced concrete work in (c)

Lintal for Ground floor and first floor

20 Providing and laying controlled cement concrete M-200 and curing etc. complete 1.00 Cumt 8767.81

including the cost of form work and reinforcement for reinforced concrete work in (c)

Lintal for S.floor

21 Providing and laying controlled cement concrete M.200 and curing complete including 231.00 Cumt 6705.39

the cost of formwork and excluding reinforcement for reinforced concrete work in (C)

Ground and first floor Slab

22 Providing and laying controlled cement concrete M.200 and curing complete including 4.00 Cumt 6746.80

the cost of formwork and excluding reinforcement for reinforced concrete work in (C)

Second Floor slab

23 Providing and laying controlled cement concrete M-200 and curing etc. complete 14.50 Cumt 7181.10

including the cost of form work and excluding the cost of reinforcement etc. complete

in (E) Stair case for Ground Floor to first floor and first floor to second

Item Rate In

Description of Item Quantity Unit Amount

No figures

24 Providing and fixing 90 cm high Stainless steel railing made from anticorrocive 304 84.00 Rmt 3719.83

grade S S pipe of 50 mm dia (16Gauge) as hand rail with S S 304 grade Baluster of

mm dia (16Gauge) as a vertical support fixed in RCC slab at 1.2m c/c including three

horizontal S S pipes of 25 mm dia (16Gauge) at eqal distance fixed by 18.75 mm dia

(16Gauge) S S pipe with baluster including accessories as per detailed drawing as

directed etc. complete.

25 Providing TMT FE 550D bar reinforcement for RCC work including bending & placing 226190.00 Kg 95.04

in position complete up to All floor Level

26 Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles having Tegular 346.00 Sqmt 1674.15

edge & 15 mm Thick Densified edges on the Tile Periphery for Extra Strength The Light weight

calcium silicate ceiling tiles shall have, light reflection 85% non-combustible as per B.S.

part IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC.for the

best thermal Insulation. The Light weight calcium Silicate tile shall be of approved texture Fine

fissured/ Spintone/ Cosmos having NRC value of 0.5 & Globe having NRC value of 0.75 NRC or

equivalent of size 595 X 595 mm to be laid on true horizontal level suspended inter locking

metal grid of hot dipped galvanized steel sections (galvanizing @120 grams per sqm including

both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and size

of 24 X 38mm made from 0.30 mm thick (minimum) sheet, 1200mm centre to centre, and cross

‘T’ of size 24 X 28mm made out of 0.33mm (Minimum) sheet spaced 1200mm along spaced

between main 'T' at 600mm centre to centre to form agrid of 1200x600mm and size 24x48mm

made of 0.30mm thick (Minimum) sheet to be interlocked at middle of the 1200x600mm panel

to form grid of size 600x600mm resting on periphery walls/partitions on a perimeter wall

angle pre-coated steel of size (24x24x3000mm made of 0.40mm thick (minimum) sheet with

the help of rawl plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm

interval and laying 15mm thick densified edges light weight calcium silicate ceiling tiles of

approved texture (Fine fissured/Cosmos/Spintone) in the grid including cutting/making

opening for services like diffusers, grills, light fittings, fixtures, smoke dtectors etc., wheneveer

required, Main 'T' runners to be suspended from ceiling using G.I. slotted cleats of size

25x35x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasterners, 4mm G.I.

adjustable rods with galvanized steel evel clips of size 85x30x0.8mm, spaced at 1200mm

center to centre long main 'T' bottom exposed with 24mm of all T-sections and also provide

additional frame work and suspended G.I. support as required height shall be pre-painted with

polyester baked paint, for all heights, as per specifications, drawings and as directed by

engineer-in-charge. Note:- Only calcium silicate false ceiling area will be measured from wall to

wall. No deducation shall be made for exposed frames/opening (cut outs) having area less than

0.30sqm. The calcium silicate ceiling tiles shall fissured/Spintone/Cosmos and 0.75 NRC for

Globe, light reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity resistance

and also having thermal conductivity. 0.043 w/m KC for the best thermal Insulation.

27 Brick work using common burnt clay building bricks having crushing strength not less 82.00 Cumt 4121.55

than 35 kg/sq.cm. in foundation and plinth in cement mortar 1:6 (1 cement : 6 fine

sand) Conventional

28 Brick work using common burnt clay building bricks having crushing strength not less 563.00 Cumt 4403.40

than 35 Kg/Sq.cm. in super structure above plinth level upto floor two level in cement

mortar 1:6 (1cement : 6 fine sand) Conventional Ground floor & First floor

29 Brick work using common burnt clay building bricks having crushing strength not less 9.00 Cumt 4444.59

than 35 Kg/Sq.cm. in super structure above plinth level upto floor two level in cement

mortar 1:6 (1cement : 6 fine sand)Conventional {Second floor}

30 Half brick masonry in common brunt clay building bricks having crushing strength not 480.00 Sqmt 669.34

less than 35Kg/Sm. In C.M 1:4( 1cement : 4 coarse sand) in super structure.

Conventional for Ground floor & First floor

31 Half brick masonry in common brunt clay building having crushing strength not less 140.00 Sqmt 675.49

than 35Kg/Sm. In C.M 1:4( 1cement : 4 coarse sand) in super structure.Conventional

for Second Floor

Item Rate In

Description of Item Quantity Unit Amount

No figures

32 Providing and fixing 150 mm wide, approved quality chicken wire mesh at junction of 974.00 Sqmt 295.12

brick work and RCC work or two dissimilar surfaces, at all heights fixed by nails, rowal

plugs or tag by cement mortar 1:3 before applying the plaster, including curing, s

33 Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or 4210.00 Sqmt 178.89

half brick walls for interior plastering upto floor two level and finished even and

smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) for G.floor and F.

34 Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or 241.00 Sqmt 206.28

half brick walls for interior plastering upto floor two level and finished even and

smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) for S. loor

35 Providing 10 mm. Thick smooth cement plaster in single coat for plastering on ceiling 1526.00 Sqmt 204.63

and soffits of stairs and finished even and smooth in : (I) Cement mortar 1:4 (1

cement : 4 sand) with floting coat of neat cement slurry etc. complete.Ground Floor &

First Floor

36 Providing 10 mm. Thick smooth cement plaster in single coat for plastering on ceiling 25.00 Sqmt 228.60

and soffits of stairs and finished even and smooth in : (I) Cement mortar 1:4 (1

cement : 4 sand) with floting coat of neat cement slurry etc. complete. Second Floor

37 20mm thick double coat sand faced cement gutka plaster on walls upto height 10 4310.00 Sqmt 337.52

metres above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement

: 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) including 1cm x

1cm grooves etc. complete.

38 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 229.00 Rmt 43.22

39 Applying two coats of putty & two coats of primer of approved brand and manufacture 5701.00 Sqmt 40.59

on new wall surface to give an even shade including thoroughly brushing the surface

free from mortar dropping and other foreign matter and sand papered smooth.

40 Wall painting (two coats) with plastic emulsion paint of approved brand and 4154.00 Sqmt 81.38

manufacture on undecorated wall surface to give an even shade including throughly

brushing the surface free from mortar droppings and other foreign matter and sand

papered smooth.

41 Wall painting (two coats) with plastic emulsion paint of approved brand and 1547.00 Sqmt 86.92

manufacture on undecorated ceiling surface to give an even shade including throughly

brushing the surface free from mortar droppings and other foreign matter and sand

papered smooth.

42 Finishing wall with Weather proof exterior 100% acrylic emulsion paint With one coat 4429.00 Sqmt 117.40

of primer on wall surface to give an required shape even shade after thoroughly

brushing the surface to remove all dirt, and remains of loose powdered materials.etc

complete for All floor

43 Providing And filling with good quality cinder(steam coal) as directed by engineer in 61.00 Cumt 589.84

charge in sunks in layers of 15 cm thick,including watering,placing ,ramming well etc

as directed, for all floor.

Item Rate In

Description of Item Quantity Unit Amount

No figures

44 Providing and laying water proofing treatment by conventional method including 238.00 sqmt 1014.04

cleaning the slab surface by wire brush as directed including provding first layer of

C.M. 1:4 of 40 mm thickness mixed with water proofing compound at rate prescribed

by manufacturer, including putting of brick bats of average thickness 40 mm Well

immerssed in water laid uniformly on first layer of mortar including applying cement

slurry @ rate of 0.08 bag/sqm. on fixed layer of brick bats including maintaining

necessary slope, in second layer 40 mm thick C.M 1:4 mixed with water proofing

compound as directed, including finishing smooth with cement slurry as directed

45 Providing and laying controlled cement concrete M-200 for RCC work and curing 25.00 Cumt 5451.98

complete including the cost of form work but excluding the cost of reinforced concrete

work in coping on Ground Floor and first floor

46 Providing and laying controlled cement concrete M-200 for RCC work and curing 23.00 Cumt 5493.39

complete including the cost of form work but excluding the cost of reinforced concrete

work in coping on 2nd Floor

47 Providing and fixing window having extruded aluminumColour anodized section frame 139.00 Sqmt 1713.70

main outer size 63.50 x38.10 x 1.95 mm,@ Wt 1.094 Kg / Rmt, horizontal two track

member size 61.85 mm x 31.75 mm x 1.20mm @wt.of 0.695 Kg/mt, vertical member of

size 61.85 mm x31.75mm x 1.30 mm @ wt.of 0.659 Kg/mt with slidingshutters of

horizontal member size 40mm x 18mm x1.29mm @ wt.of 0.456Kg/mt, vertical

member of size40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt, @ Wt.0.457 Kg/mt with

5 mm thick transparent bronze colour float glass with powder coated aluminum fitting

sand fixtures and transparent silicon sealant glass fixing to frame as per details etc

complete for window.

48 Providing and fixing window having extruded aluminumColour anodized section frame 15.00 Sqmt 1583.95

main outer size 95mm x24mm x 1.17mm @ wt.of 0.738 Kg/mt , horizontal Three track

member size 92mm x 31.75mm x 1.30mm,@Wt.1.07 Kg/mt , vertical member of size

92mm x31.75mm x 1.50mm @ Wt. 1.06 Kg/mt with slidingshutters of horizontal

member size 40 mmx18mmx1.29mm @ wt.of 0.456 Kg/mt, vertical member of

size40mm x 18mm x 1.29 mm @ wt.of 0.456Kg/mt/ with 5mm thick transparent

bronze colour float glass with powder coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame as perdetails etc

49 Providing and fixing window having extruded aluminum Colour anodized section 28.00 Sqmt 1525.00

frame of size 63.50 x 38.10 x 1.95 mm,@ Wt 1.094Kg / Rmt with colour anodized

alluminium frame with 5 mm thick transparent bronze colour tinted float glass as with

powder coated aluminum fittings and fixtures and transparent silicon sealant glass

fixing to frame as perdetails etc details etc complete for Fix window

50 Providing & Fixing in position standard extruded approved colour anodised Aluminum 16.00 Sqmt 1975.76

Ventilation with outer frame 65 x 25 x 1.50 mm Frame @ Wt 0.833 kg/Rmt with 3 mm

thick fixed Bajari glass a alluminium strip blade fixed or adjestable ventilation,Fixed

glass, exhuast fan including all required materials, fixtures, fastenning, labours and

equipments as per detailed drawing as directed. For Ventilation

Item Rate In

Description of Item Quantity Unit Amount

No figures

51 Providing and fixing Double shuttered door with side fixed ventilation having frame 18.00 Sqmt 4028.89

granite stone with flat edge polished with standard extruded colored anodized

aluminum section main frame outer size 127mm x 38.10mm x 1.35mm (weight -

kg/rmt.). Openable shutters and 50mm thick double shutter flush door solid core

finished with 1mm thick lamination on both sides colored and pattern approved by

this office with fixed glazing on sides. Door shall be provided with floor spring and

60cm long S.S. handle and Locking system and S.S. fixtures & fastenings etc. directed

by engineer in charge.

52 Providing and fixing single shuttered Door having frame of granite stone with flat edge 95.00 Sqmt 4841.94

polished with standard extruded colored anodized aluminum section main frame outer

size 127mm x 38.10mm x 1.35mm (weight - 1.384 kg/rmt.). Openable shutters and

mm thick single shutter flush door solid core finished with 1mm thick lamination on

both sides colored and pattern approved by this office with fixed glazing on sides. Door

shall be provided with floor spring and 60cm long S.S. handle and Locking system and

S.S. fixtures & fastenings etc. directed by engineer in charge.

53 Providing and fixing FRP frame size 100x50 mm and 28mm thick FRP depress panel 40.00 Sqmt 2377.76

shutter having extra reinforcement on sides & edges in Gel coat finish. The core of the

shutter & frame is to be filed up with injected fire retardant grade polyurethene foam

done in situ alongwith embedded wooden pieces for stiffening & also taking hinges &

fintures. The whole FRP frame & shutter is to be water proof weather proof, termite

proof & resistance to mild acid/alkali. Rates are to be inclusive of S.S hinges with

necessary screws & alluminium fixtures & fastenings & fastener sleeve.

54 P & L 60x60 cm' Anti skid vitrified 8 mm thick tile for flooring of cement mortar 1:6 866.50 Sqmt 1404.91

(1cement : 6 coarse sand)and jointed with by adhesive materials including colour

cement slurry including finished with flush pointing & cleaning the surface etc.

complete for including two colour pattant colour approved by directed.

55 Providing and fixing anti-skid vitrified tiles 8 to 10 mm thick, 600 mm × 600 mm (24" × 46.50 Sqmt 1492.78

24") in skirting, fixed on vertical surface over cement mortar 1:3 (1 cement : 3 coarse

sand), jointed with matching colour cement slurry, including two-colour pattern as

approved, finishing with flush pointing and cleaning the surface complete.

56 Providing and laying machine cut free edge machine Double polished granite stone 423.00 Sqmt 2023.03

18mm thick finished treads and risers in with 1cm projecting, nozing rounded

moulding in tread laid over 12 mm (av.) thick bases of cement mortar 1:6 (1-cement : 6-

coarse sand) jointed with grey or colour cement slurry including rubbing and

polishing incl. making Three No.s of grooves of size 3mm X 3mm along the length of

treads etc. complete

57 P & L Mate Finished antiskid ceramic tiles 30x30 cm size 6 mm thick in flooring treads 257.00 Sqmt 929.39

of steps and landing laid on a bed of 12 mm thick cement mortar 1:3(1-cement:3-

coarse sand)finishing with flush pointing in white cement

Item Rate In

Description of Item Quantity Unit Amount

No figures

58 Providing and laying coloured glazed tiles of the size 300 mm x 200 mm x 8 mm / 300 1060.00 Sqmt 1477.25

mm x 450 mm x 8 mm ,300 mm x 300 mm x 8 mmin skirting, risers of steps and dedo

on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with white

cement slurry.

59 Providing Plinth Protection to Building including excavation in ordinary soil and laying 235.00 Sqmt 2473.59

cement concrete 1:3:6 using stone aggregates of 40mm nominal size in foundation

layer 125 mm thick+ 125mm thick sand layer below pre-cast Rubber Dye inter locking

concrete block 60mm thick with grade of concrete M300 pneumatic compressed by

mechanically pressed and as per approved design including 75mm Sand layer for

levelling and filling the joint with sand in proper line and level etc. complete, Including

Providing and fixing pre-cast concrete kerb stone of grey cement based concrete block

30cm length, 30cm height and 15cm thick made of M250 grade concrete as per

approved design and including excavation for fixing in proper line and level, filling the

joint with C:M 1:3 (1cement:3 fine sand) etc. complete.

60 Providing and laying China mosaic type water proofing treatment on terrace including 852.00 Sqmt 1113.02

cleaning the surface by wire brush as directed including applying neat cement slurry @

2.75 Kg/Sq.smt. mixed with water proofing compound after cleaning the surface, laying

cement concrete using brickbats 25 to 100mm size well immersed in water with 50%

of cement mortar 1:5 (1 cement :5 coarse sabd) mixed with water proofing compound

over 20mm thick layers of cement mortar 1:5 (1 cement :5 sand) to required slope

including rounding of junctions of walls and slabs and after two days of proper curing,

applying second coat of cement slurry finishing the surface with rate 20mm thick

cement mortar 1:4 and china mosaic tiles and finally finishing the surface with white

cement slurry and after finishing the whole terrace shall be flooded with water for a

period of two weeks.

61 Providing and fixing polished 18 mm thick Granite stone with full round edge and 322.00 Sqmt 2475.51

polished of approved quality in clading on sill and around the doors/ windows/

ventilation with 20 mm thick cement plaster CM (1:4) and fixing with cement slurry &

adhesive including moulding of exposed edges as directed by engineering in charge etc.

62 Providing and fixing M.S Safty Grills having 16mm MS bar Horizontally at every equal 209.00 Sqmt 3472.99

0.10m C/C distance and 2 no of bar Vertically at every equal 0.375m C/C distance

Fixing on around (5x40) mm Solid MS Patti including cutting, welding and fabrication

etc; including one coat of primer of approved quality and two coats of oil painting as

per detail drawing etc. complete as per directed Engineer in charge.

63 Providing erecting and fixing double coated Syntex PVC. (ISI) water tank of required 15000.00 Litre 3.95

capacity each with all necessary fittings and connection etc. complete on terrace.

Item Rate In

Description of Item Quantity Unit Amount

No figures

64 Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) 90.00 Rmt 195.67

for cold water including fittings make as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all materials.

65 Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) 70.00 Rmt 148.12

for cold water including fittings make as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all materials.

66 Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) 180.00 Rmt 91.84

for cold water including fittings make as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all materials.

67 Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) 160.00 Rmt 72.65

for cold water including fittings make as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all materials.

68 Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) 120.00 Rmt 834.38

conforming to IS 13592-1992 with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system

pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed

on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm

heigh at every 2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all materials.

69 Providing laying (to level or slopes) and jointing reinforced concrete Light duty non- 538.00 Rmt 678.01

pressure pipes I.S. class NP2 of the following internal diameter with collars and butt

ends prepared for collar joints including testing of joints complete.(D)

Item Rate In

Description of Item Quantity Unit Amount

No figures

70 Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) 126.00 Rmt 857.65

conforming to IS 13592-1992 with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system

pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed

on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm

heigh at every 2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all materials.

71 Providing, laying and jointing in true line and level 75 mm dia. UPVC SWRType B pipe 50.00 Rmt 292.90

conforming to IS 13592-1992 with one end plain and other end socketed with

rubbering and fitting conforming to ISI 14735-1999 of approved make for drainage

system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall

be fixed on wall using of PVC clamp at every 2000 mm c/c or shall be conceled in walss

as directed including necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement including cost of all

materials.

72 Providing and fixing in PVC SWR cowel went 75mm dia to pipes.(B) 75mm dia. 5.00 No 15.66

73 Providing and fixing in PVC SWR cowel went 110mm dia to pipes.(B) 110mm dia. 16.00 No 28.79

74 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with 56.00 No 585.37

jali of the following nominal diameter of self cleansing design with C.I scread down or

hinged grating including the cost of cutting and making good the walls.

75 Providing and fixing wash down water closet (European type W C pan) with integral P 17.00 No 2983.54

and S trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement

five sand) including providing and fixing plastic seat cover for wash down WC with CP

brass hinges and rubber buffers back plastic seat and including providing and fixing

PVC flushing tank with a pair of C I or MS bracket with complete fitting such as lead

valve siphon 15 mm dia brass ball valve with polythene float CP brass handle unions

and couplings for connection with inlet out let and over flow pipes 40 mm dia

porcelain enameled flush bend including cutting holes in walls and making good the

same connection the flush bend with cistern and closet vitreous china.

{Hindustan, Cera, Parryware or equivalent }

76 Providing and fixing Urinal of approved quality including connection with trap and 9.00 No 2593.68

with integral longitudinal flush pipe.(A) Squating plate pattern white earthenware

77 Providing and fixing polished 18 mm thick black granite with full round edge and 16.00 Sqmt 2603.17

double side polished of approved quality in between urinal and fixing with cement

slurry & adhesive including moulding of both exposed edges as directed by engineering

in charge etc. complete.

78 Providing and fixing brass screw down stop tap.(A) 15mm dia. 43.00 No 205.83

79 Providing and fixing ball cock of approved. quality as directed.(A) Copper Metal (ii) 3.00 No 189.84

Item Rate In

Description of Item Quantity Unit Amount

No figures

80 Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets 23.00 No 1649.22

painted white including Rubber plug, sutting holes and making good the same but

excluding fittings and also including rate of C.P. brass waste for washbasin or sink (A)

32mm dia. and M.I. fisher union for washbasin or sink. (A) 32mm dia.; (A) Vitreous

China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour.

81 Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass 18.00 No 852.76

mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with

C.P. brass screws and washers.

82 Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to 18.00 No 616.42

wooden plugs with C.P. brass scews (B) 600mm x 20mm size.

83 Providing and fixing screw down bib taps of following size.(A) Brass screw down bib 50.00 No 214.81

tap polished bright. (i) 20mm dia.

84 Providing and fixing pillar tap, capstan head, screw down high pressure with screws, 23.00 No 308.73

shanks and back nuts. (i) 15mm dia.

85 Providing and fixing in position 300 mm high, 150 mm wide English letters made from 120.00 No 707.00

1.0 mm thick stainless steel sheet as directed by Engineer in charge with all necessary

tools & plants etc. complete.

86 Providing and fixing Rubber plug for sink or wash basin. 23.00 No 17.15

87 Providing and fixing chromium plated brass half trun flush cock of approved quality 18.00 No 263.77

including fixing in pipe line etc. complete (ii) 25mm dia.

88 Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water 20.00 No 1246.92

tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight (i)

Square mouth traps (B) 150mm x 100mm size P or R type

89 Constructing brick masonry chamber for underground C.I. Inspection chamber and 26.00 No 3172.41

bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5

precast RCC cover 455mm x 610mm intenal dimensions with frame (R.C.C. top slabe

with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and bed concrete etc. complete (i)

Inside dimensions 455mmx 610mm and 450mm deep for single pipe line.

90 Constructing brick masonry chamber for underground C.I. Inspection C.I. Inspection 22.00 No 3883.45

chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in

C.M. 1:5 precast RCC cover 500mmx 700mm intenal dimensions with frame (R.C.C. top

slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and bed concrete etc. complete (i)

Inside dimensions 500mmx 700mm and 450mm deep for single pipe line.

91 Extra over items for every additional depth of 0.1M. of part thereof beyond 450mm 18.00 Each 242.39

depth for Brick masonry chamber.(i) for 455mm x 610mm size.

Item Rate In

Description of Item Quantity Unit Amount

No figures

92 Extra over items for every additional depth of 0.1M. of part thereof beyond 450mm 14.00 Each 264.86

depth for Brick masonry chamber.(i) for 500mm x 700mm size.

93 Providing cement vata (10cm x 10cm size) quarter round in cement mortar 1:1 140.00 Rmt 24.28

including neat cement finishing watering etc. Complete

94 Providing and fixing MS Ladder of required pattern with MS flats(30x3mm) or round 300.00 Kg 115.14

or square bars (12mm) at required spacing & with round headed bolts and nuts or

screws or welding including primer coat of approved quality and two coats of oil

paintas as directed by engineer in charge

95 Providing and fixing in position 150 mm high, English letters made from 1.0 mm thick 100.00 No 404.00

stainless steel sheet as directed by Engineer in charge with all necessary tools & plants

etc. complete.

96 Constructing Platform of 18 mm thick Polished Black Granite at top and 25 mm thick 3.00 Sqmt 6235.74

Kota stone slab one side polished at bottom with cementing Materials / adhsives

including makeing necessary grooves in walls with Vertical sandwich two Kotastone

25 mm support every 60 cm centre to centre or as required including all labour

material of approved quality incl. full moulded round front edge granite strip of one

side polished and jointed with grey cement slurry including rubbing and polishing etc.

complete for all floors

97 Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 958.00 Sqmt 704.07

60mm thick with grade of concrete M300 pnumatic compressed / vibrated

mechanically and as per approved design Confirming to IS 15658 : 2006 including

mm Sand layer for levelling and filling the joint with sand in proper line and level as

per guidlines of IRC : SP 63-2018 etc. Complete.

98 Providing and fixing 0.60 meter wide Drinking platform including supplying and 9.00 Sqmt 2831.03

fixing granite stone of black or equivalant quality 18 mm thick mirror polished on top

and side posiition and vertical strip at front with cement slurry & adhesive including

moulding of both exposed edges over 25 mm thick kotah stone platform fixing in top

and sides and itermediates supports fixing with cement mortar and adhesive and

finishing all material and labour and assessories with necessary fitting complete etc.

99 Constructing Kitchen Platform of 18 mm thick Polished Black Granite at top and 25 17.00 Sqmt 4193.52

mm thick Kota stone slab one side polished at bottom with cementing Materials /

adhsives including makeing necessary grooves in walls with Vertical sandwich two

Kotastone 25 mm support every 60 cm centre to centre or as required including all

labour material of approved quality incl. full moulded round front edge granite strip

of one side polished and jointed with grey cement slurry including rubbing and

polishing etc. complete for all floors

100 Providing and fixing 25 mm thick polished kota stone Shalve with full round edge and 27.00 Sqmt 667.61

double side polished of any required and fixing with cement slurry & adhesive

including both exposed edges cut and Smooth Finished as directed by engineering in

charge etc. complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

101 Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white including 1.00 Nos 3640.04

cutting holes in walls and making good the same but excluding fittings. (C) Vitreous

China Sink.(i) 600mm x 450mm x 150mm size

102 Providing and fixing Kitchen platform trolley having three drawers of SS (IS 304) of 7.00 Sqmt 12364.42

required size like thali, katleri, perforated, partition, cupsosar type in kitchen platform

having drawer front side and backside by using 19mm thick all proof plywood of ISI

quality all side laminated etc. as directed. The size of SS (IS 304) basket of size 4" to 18"

for thali, dish, katleri, perforated, partition, cupsosar type as directed including

necessary S.S. fittings, handles, nobs, telescopic channels, etc. as directed

103 Providing and fixing coloured self adhesive PU-Tactile tile, ground surface indicators of 33.00 Sqmt 4791.44

Polyurethane) of size 300mm x 300mm for guiding/warning to the visually visitors in

the centre/side of the pedestrian/approach pathway as per specification and

guidelines complete in all respect to the entire satisfaction of in charge.

104 Providing and fixing acrylic multilingual Braille (raised dots) DIRECTIONAL 20.00 Nos 1765.48

SIGNBOARDS of size 225 x 150mm designed as per accessibility standards and having

3.5mm thick acrylic base plate with Upper Case San Serif words made of white acrylic

non glare cut out letters of height 15mm raised not less than 0.8mm above base plate

and the equivalent word written in Hindi with Devanagari non glare acrylic letters of

height 15mm raised not less than 0.8mm above base plate and having a non-glare

acrylic cut arrow pointing in the required direction. Each signboard to be fixed as per

manufacturers specifications on the wall at the approved location and at a height of

1200mm from FFL complete as per design / specifications and guidelines as per the

entire satisfaction of the Engineer-in-charge

105 Providing & Fixing Braile Indicator Of Size 170 Mm X 35mm For Handrails Of The 45.00 Rmt 946.37

Approved Design And Make Have Braile Dots Raised 0.5 Mm Above Base Plate To Be

Installed At Specific Locations As Per Direction Of Engineer In Charge

106 Providing and fixing of conspectus tape 50mm width on of treads in staircase including 34.00 Rmt 304.01

cutting pasting etc. As per harmonised guidelines complete in all respect to the entire

satisfaction of engineer in charge.

107 Providing and Fixing a set of wall mounted 38 mm dia U shaped horizontal stainless 2.00 Set 2730.03

steel collapsible grab bar , 38mm vertical stainless steel fixed grab rail of grade SS

from round pipe supported and 75 mm dia 8 mm thick SS 304 base flange on wall

including anchor fasteners, nuts, accessories as per detailed drawing etc. complete as

directed by Architect or Engineer in charge.

108 Providing and fixing EURONICS 304 Stainless Steel Handicap Grab Bar, Size 600 6.00 Nos 3368.35

millimeter, including all necessary fittings and fixtures, complete as per the direction of

the Engineer-in-charge.

Item Rate In

Description of Item Quantity Unit Amount

No figures

109 Providing and fixing rolling shutters of approved make made of 80 mm wide M.S. laths 17.00 sqm 3554.40

inter-locked together through their entire length and jointed together at the ends by

end locks mounted on specially designed pipe shaft with bracket plates, guide channels

and arragements for inside and outside locking with push-pull operation including the

cost of hood cover and spring etc. complete.(A) Shutters having width below 3.5 M.

110 Providing and laying controlled cement concrete M.200 and curing complete excluding 39.00 Cumt 8971.83

the cost of formwork and reinforcement for reinforced concrete work in (B) Walls,

from top of foundation level upto floor two level

111 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight not less 2.00 Nos 958.17

than 35Kg.

112 Providing & erecting open well horizontal mono block pump set with cast iron body, 2.00 Nos 36107.50

complete for three phase submersible motor having [H]For 15 H.P,3 phase open well

horizontal mono block pump set suitable for 1600 LPM to 1025 LPM @ 33 to 42 MTR

head suitable for 65/80 mm dia delivery pipe

113 Supplying & erecting approvedmake 3 phase motor control cubicalpanel (Star-Delta) 2.00 Nos 19695.00

made from 16G.CRCA sheet duty painted with epoxy powder painted inside and

outside with hinged doors and locking arrangement, consisting suitable size of ON-OFF

isolator (AC- 3/23duty) main fuses,single phasing preventer cum water level,

Guard(Compe unit), Toggle switch to by pass Single phase preventercum

WLG,indicating lamps forR-Y-Bphases, over load relay.Automatic water level

duty socket Crimped,Panel to be erected on angle iron frame grouted on wall as

overload relay,thermal/Electronics star delta cutoff timer,start-stop push buttons.The

isolator overload relay &cntractors ofL&T,Siemens or Cuttler Hamer make only.Panel

to be erected on angle iron frame ground on wall (e)S/D upto 2.5 H.P.

114 Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and 17.00 Cumt 178.58

stacking of useful materials and disposing off the excavated stuff upto 50 Meter

lead.(B) Dense or Hard soil

115 Constructing brick masonry chamber for underground C.I. Inspection chamber and 4.00 No. 7180.44

bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I.

cover with frame (Light duty) 455mm x 610mm intenal dimensions, total weight of

cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg.

) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar

1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc.

complete.(iii) Inside dimensions 600mm x 850 mm and 450mm deep for pipe lines

with three or more inlets.

116 Box cutting the road surface to proper slope and camber for making a base for road 900.00 Cum. 106.64

work including removing the excavated stuff and depositing on the road side slope as

directed upto 50Mt.lead.

117 Filling in plinth with sand under floors including watering ramming, consolidating and 169.00 Cum. 342.39

dressing complete

Item Rate In

Description of Item Quantity Unit Amount

No figures

118 Construction of granular sub-base 150 mm thick by providing coarse graded machine 219.00 Cum. 723.16

crushed B.T. material satisfying MOST specification of grading I (B.T. stone aggregate

53 mm to 26.5 mm 35 %, 26.5 to 4.75 mm - 45 % and 2.36 mm below - 20 % )including

spreading in uniform layer with motor grader on prepared surface, mixing by mix in

place method with rotavator at OMC and compacting with vibratory roller to achieve

the desired density etc. complete.

119 Providing and laying wet mix macadam base course 250 mm thick using machine 282.00 Cum. 761.54

crushed B.T. chips as per required gradation mixing with required optimum quantity of

water, conveying the mix to site of work, spreading in to grade and camber with

mechanical paver and consolidation each layer with vibratory roller including cost of

material labour plant and equipment etc. complete.

120 Compaction and finishing of cement concrete road by trimix M.250 process providing 1071.00 Sqm. 63.63

extra Labour charges for the trimix vacume dewatering service process on cement

concrete road sutface by using vacuum dewatering pump floater surface vibrator

including making groves and rough finish to surface including leveling etc complete.

121 Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 396.00 Rmt. 370.68

30cm length,30cm height and 15cm thick of M250 grade concret as per approved

design and including excavation for fixing in proper line and level,filling the joint with

C:M 1:3 (1cement:3fine sand) etc complete.

122 Drilling pilot borehole of size 250/300 mm at above site by mud flush direct rotery rig. 100.00 Rmt 853.25

123 Reaming of 250/300 mm dia.Pilot borehole to size 550 mm dia. Incliding assembling 15.00 Rmt 527.95

,lowering housing ,casing strainerpipers with gravel packing and clayball packing etc.

124 Development of cach water bearingzone coming across the full depth of tubewell by 1.00 Job 13212.90

lowering 100 mm dia.Droplineand 32 mm dia airline for each water bearing Zone with

suitabale capacity air compressar up to avilability of sand free discharge.

125 900 CFM /200 PSI capacity air compressar upto the availability of sand free discharge 1.00 Job 27206.17

for upto 250 mtrs

126 Supply of M.S. E.R.W. plain end medium duty pipe confirming to IS 4270/2001 with 100.00 Rmt 2440.64

latest amendments Of size 250 mm dia (minmum thicknes of 7.1 mm)

127 Screen Slotting of MS ERW balnce pipe with size of slot 6.75 cm X 6.35 cm X 3.12 mm 200.00 slots 0.22

for 250 mm dia pipe

128 Supply of miscellenious bore material suitable to 250 mm dia pipes as following (A) MS 1.00 Pair 1912.70

Bore clamps made from M.S. plate with 3 holes on either side with nuts & bolts of std

make of size 900X100X16 mm flat suitable for 250 mm dia pipe.

129 Supply of miscellenious bore material suitable to 250 mm dia pipes as following (B) MS 1.00 No 1385.64

Bore Plug having 100mm height made from M.S. plate with 3 holes at equal distance on

circumferrence for nut-bolts type, locking arrrangement with nuts-bolts & lock nuts of

std make complete from 5 mm thick M.S. plate suitable for 250mm dia pipe.

Item Rate In

Description of Item Quantity Unit Amount

No figures

130 Supply of miscellenious bore material suitable to 250 mm dia pipes as following (C) MS 1.00 No 999.90

Bail Plug having length 0.45 mtr from medium class pipe as per I.S. suitable for

mm dia pipe.

131 Supply of miscellenious bore material suitable to 250 mm dia pipes as following (D) 168.00 NO 86.21

Steel bent plate suitable for ERW pipe for 250mm dia (size:200 X 150X6 mm)

133 Electrologging of Pilot bore hole with carting. 1.00 Job 10665.60

134 Geohydrological ground water investigation including vehicle charges for three phase 1.00 No 14220.80

DTH bore/DR tube well including water sample testing & chemical analysis

135 Providing, supplying and commissioning ISI mark CI D/F Reflux Valves of following 1.00 No 4753.30

class and diameter including all taxes, insurance, transportation, freight charges,

octroi, inspection charges, loading, unloading, conveyance to departmental stores

stacking etc. complete. Reflux valves PN 1 IS 5312 with ISI mark size: 100 mm

136 Providing and laying in trenches galvanised mild steel tubes (Midium grade) of the 100.00 Rmt 921.68

following nominal bore, and tube fitting (Earthwork in trenches to be measured and

paid for separately (H) 80mm

137 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure 150.00 Rmt 339.05

poluthene pipes of the following outside Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including making good the wall ceiling and

floor.(G)110 mm

138 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure 130.00 Rmt 859.51

poluthene pipes of the following outside Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including making good the wall ceiling and

floor.(G)160 mm

139 Providing junction for rain water juncton chamber of size 0.60x0.60x0.75m with 12.00 Nos. 9007.18

excavation of size 1.96x1.96 m & 0.15m thick c.c.1:2:4 bed concrete including brick

masonary wall in CM 1:6 of 0.75m height & 0.23m thick with 15mm thick cement

plaster inside & outside & 1.06x1.06 RCC (1:2:4) slab of thickness 0.15m with CRS

steel and 0.60mx0.45m cast iron manhole cover with frame weight not less than 35 kg

as per directed by Engineer-in-charge

140 Providing and installation Recharge pit of “RAIWOHA” Make 3 layer RCC Precast 1.00 Nos. 109645.60

Injection well system of size 1.5 meter Dia. X 3.4 Meter Height rein forced concrete

precast three layer module with 6” dia x 12” dia. V wire screen of 0.75mm x 1.0 mm

Slot size in SS 304 material and 1.0 meter height with MS Top cover and required Air

vent including all necessary excavation and transportation at site including required

filter media for the recharge system as per site requirement.

141 Drilling of min. 250 mm dia. bore hole in all strata including dualover burden strata by 30.00 Rmt 1270.58

combination DR/DTH rig including lowering 200 mm dia MS ERW pipes in bore hole

and testing etc.all work as per directed engineer incharge.

Item Rate In

Description of Item Quantity Unit Amount

No figures

142 Supplying slotted PVC pipes of approved quality at site of work confirming to IS. 30.00 Rmt 555.50

1239/1974 180mm dia.

143 Cleaning & maintenance of system Including all Labour and replacing of Filter Media as 1.00 Nos 4646.00

Required for one year

144 Constructing providing and fabricating cattle guard using channel section frame of size 6.00 Sqmt 5104.54

ISMC series 100 mm x 50 mm (Weight 9.20 kg/Rmt) and ISMC section 100 mm x

75mm (weight 11.50 kg/Rmt) intermediate support for welding G.I.pipe at 12 Cm C/C

of size 50 mm in a frame made of Channel section size 100 mm x 50 mm all round

including fixing the unit on prepared chamber of masonary wall using MS hold fast

embeded in masonary wall top as directed by Engineer in charge and as per drawing

and necessary required arrangement etc complete.

145 Providing and fixing decorative entrance gate made out of cast iron and various mild 825.00 kg 167.66

steel tabular section combination , the Ornamental entrance gate should be fixed at

compound wall including pattern and die making , cutting , welding , grinding,

fabrication , fixing in position at compound wall with necessary pedestal, bearing block

and other locking arrangement. The entrance gate should be painted with two coats of

priming coat of paint, and two coat of oil paint etc complete. As per detail design and

instruction of architect.

146 Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm 437.00 Rmt 669.63

dia 10 mt openable length having 50 no rounds per 6 mt length, upto 3mt height of

wall with existing angle iron (50mm x50mm x5mm )requird shaped As per Directed

Engeenier in charge. placed 2.4mt or 3.00mt apart and with 4 horizontal R.B.T.

reinforced barbed wire(3 mm) , stud tied with G.I. staples and G.I. clips to retain

horizontal, including necessary bolts or G.I.barbed wire tied to angle iron, all complete

as per direction of Engineer-in-charge, with reinforced barbed tape (R.B.T.)/Spring

core (2.5 mm thick) and weight 43.478 gm/meter at compound wall for ESR M4/

intakewell.

147 Steel work, welded in built up sections framed work including cutting, hoisting, fixing 11516.00 kg 91.08

in position and applying a priming coat of read lead paint & two coat oil paint. (A)In

beams and joists, channels angles Tees, flats, with connecting plates or angle cleats as

in main and cross beams. Hip and jack rafters, purlins conneted to common rafters and

the like..

148 Providing and fixing of Ridge flashing for roof panel shall be made out of 0.5 mm thick 329.00 Sqm 867.39

pre coated GI sheet . The Precoated sheet shall be of minimum 240 mpa steel grade

confirming to IS 14246:1995 and shall have zinc coating of minimum 120 gsm as per

IS:277:1992 , 5-7 microns epoxy primer on both side of the sheet and polyester top

coat 15-18 micron. The PPGI Sheet shall have plastic protective guard film of minimum

25 microns to avoid scratches during transportation. The ridge shall be fixed to the

steel members by pop rivet or self drilling/self stitching fastners @ maximum 450 mm

c/c along length of capping/flashing etc complete .

Item Rate In

Description of Item Quantity Unit Amount

No figures

149 Earthwork for embankment including breaking clods, dressing with all lead and lift 2914.01 Cum 236.07

(excluding watering and consolidation)(E) From Borrow area within 3.0 Km. lead

150 Rolling and watering of Earth work in layers with power roller including filling in 2914.01 Cum 22.89

depressions which occure during the process.

151 Supply, installation, testing & commissioning of ISI approved electrical motor driven 1.00 No 65650.00

jockey pump set having 10.8 m3/hr. @ 70m head. The pump unit shall be a

horizontally direct mounted motor. Unit shall comprise the following minimum

requirements: a) Pump, b) Electric motor IE2, c) Foundation bolts, d) Mating flanges

with gasket and fasteners, e) Discharge gauges, etc. complete in all respect, with labour,

152 Supply, installation, testing & commissioning of Priming tank, HDPE type, 1000 litres, 1.00 No 25250.00

with necessary piping 100 mm size, G.I pipe for priming the pumps, pipe of with

butterfly valves for isolation, Water Filling to priming tank by piping min. 50 mm size,

with all complete.

153 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW piping, conforming to 5.00 Mtr 343.40

IS:1239, part-I, Heavy class up to 150 mm dia. and IS:3589, for size 200 mm dia. &

above, thickness. G.I. pipe fitting's as per IS: 1239, part-II, Heavy class for size 150 mm

dia. & below & IS: 3589, for size 200 mm dia. above, flanges, nuts bolts & washers,

mm thick gasket, pipe hangers, etc. Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc. Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved drawings, specicification and direction

of the Engineer-in-Charge, with all complete. (A) 25 mm dia.

154 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW piping, conforming to 13.00 Mtr 555.50

IS:1239, part-I, Heavy class up to 150 mm dia. and IS:3589, for size 200 mm dia. &

above, thickness. G.I. pipe fitting's as per IS: 1239, part-II, Heavy class for size 150 mm

dia. & below & IS: 3589, for size 200 mm dia. above, flanges, nuts bolts & washers,

mm thick gasket, pipe hangers, etc. Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc. Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved drawings, specicification and direction

of the Engineer-in-Charge, with all complete. (B) 50 mm dia.

155 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW piping, conforming to 31.00 Mtr 1111.00

IS:1239, part-I, Heavy class up to 150 mm dia. and IS:3589, for size 200 mm dia. &

above, thickness. G.I. pipe fitting's as per IS: 1239, part-II, Heavy class for size 150 mm

dia. & below & IS: 3589, for size 200 mm dia. above, flanges, nuts bolts & washers,

mm thick gasket, pipe hangers, etc. Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc. Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved drawings, specicification and direction

of the Engineer-in-Charge, with all complete. (C) 80 mm dia.

Item Rate In

Description of Item Quantity Unit Amount

No figures

156 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW piping, conforming to 182.00 Mtr 1414.00

IS:1239, part-I, Heavy class up to 150 mm dia. and IS:3589, for size 200 mm dia. &

above, thickness. G.I. pipe fitting's as per IS: 1239, part-II, Heavy class for size 150 mm

dia. & below & IS: 3589, for size 200 mm dia. above, flanges, nuts bolts & washers,

mm thick gasket, pipe hangers, etc. Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc. Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved drawings, specicification and direction

of the Engineer-in-Charge, with all complete. (D) 100 mm dia.

157 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW piping, conforming to 7.00 Mtr 1969.50

IS:1239, part-I, Heavy class up to 150 mm dia. and IS:3589, for size 200 mm dia. &

above, thickness. G.I. pipe fitting's as per IS: 1239, part-II, Heavy class for size 150 mm

dia. & below & IS: 3589, for size 200 mm dia. above, flanges, nuts bolts & washers,

mm thick gasket, pipe hangers, etc. Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc. Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved drawings, specicification and direction

of the Engineer-in-Charge, with all complete. (E) 150 mm dia.

158 Supply, installtion, testing & commissioing of Underground GI (ERW) piping 25.00 Mtr 2585.60

conforming to IS:1239, part-I, Heavy class ('C' class) up to 150 mm dia. and IS:3589

Heavy class ('C' class), for 200 mm dia. & above, min. 6.35mm thickness including

Heavy class fittings, anti-corrosive tape of size 150 mm wide x 4 mm thick, wrapping &

coating with 13KV holiday testing . Rates shall include sand bedding of 75mm dia all

around, backfilling of the excavated including installation of heavy pipe fitting's,

flanges, etc. 10 % of all the welded joints shall be done radiographically tested and

50% of the joints radiographed shall be the "Field Joints". Hydrostatic testing for

hours at 150% of the system pressure, hook-up etc., complete with all accessories as

per approved drawings, specicification and direction of the Engineer-in-Charge, with

all complete. (Road Crossing) (B) 100 mm dia.

159 Design, Supply and installation of Safety Signage made of Zinc Sulphilde based glow in 4800.00 Sq. Inch 9.09

dark, Rigid sheet with High Luminous property enclosed in a transperent weather

proof UV stabilized plastic pasted on 3 mm thick clear acrylic sheet such as EXITS,

EMERGENCY EXIT, DO NOT USE LIFT DURING FIRE, FLOOR MARKINGS, FIRE LIFT,

STAIRCASE EXIT, FIRE ALARM CALL POINT, FIRE HOSE REEL, FIRE HYDRANT POINT

160 Supply, installation, testing & commissioning of Pressure switch. (Range 0 to 16 2.00 No 1262.50

161 Supply, installation, testing & commissioning of 150 mm dia. dial Burdon Type 4.00 No 1767.50

Glycerine Filled pressure gauge with isolation ball valve arrangements with necessary

isolation valves with all complete. (Range 0 to 15 kg/cm2)

Item Rate In

Description of Item Quantity Unit Amount

No figures

162 Supply, Installation, Testing & Commissioning of Cast iron body Butterfly valve 4.00 No 1262.50

according to IS: 13095, PN-1.6, Iron Disc for size 150 mm dia. & below Lever operated

and above 150 mm dia. Gear operated complete with mating flanges/ ANSI class #

with bolts & nuts washers, rubber gaskets 3 mm thick, etc. with all complete. (A)

163 Supply, Installation, Testing & Commissioning of Cast iron body Butterfly valve 2.00 No 1565.50

according to IS: 13095, PN-1.6, Iron Disc for size 150 mm dia. & below Lever operated

and above 150 mm dia. Gear operated complete with mating flanges/ ANSI class #

with bolts & nuts washers, rubber gaskets 3 mm thick, etc. with all complete. (B)

164 Supply, Installation, Testing & Commissioning of Cast iron body Butterfly valve 8.00 No 3019.90

according to IS: 13095, PN-1.6, Iron Disc for size 150 mm dia. & below Lever operated

and above 150 mm dia. Gear operated complete with mating flanges/ ANSI class #

with bolts & nuts washers, rubber gaskets 3 mm thick, etc. with all complete. (C)

165 Supply, Installation, Testing & Commissioning of Cast iron body Butterfly valve 1.00 No 3585.50

according to IS: 13095, PN-1.6, Iron Disc for size 150 mm dia. & below Lever operated

and above 150 mm dia. Gear operated complete with mating flanges/ ANSI class #

with bolts & nuts washers, rubber gaskets 3 mm thick, etc. with all complete. (D)

166 Supply, installation, testing & commissioning of Cast iron body Dual Plate Wafer Type 1.00 No 1272.60

NRV conf. to IS: 210, PN-1.6 complete with mating Flanges class # 150 with bolts &

nuts, washers, gaskets 3 mm thick, etc. with all complete Accessories (A) 50 mm dia.

167 Supply, installation, testing & commissioning of Cast iron body Dual Plate Wafer Type 1.00 No 1414.00

NRV conf. to IS: 210, PN-1.6 complete with mating Flanges class # 150 with bolts &

nuts, washers, gaskets 3 mm thick, etc. with all complete Accessories (B) 80 mm dia.

168 Supply, installation, testing & commissioning of Cast iron body Dual Plate Wafer Type 3.00 No 1767.50

NRV conf. to IS: 210, PN-1.6 complete with mating Flanges class # 150 with bolts &

nuts, washers, gaskets 3 mm thick, etc. with all complete Accessories (C) 100 mm dia.

169 Supply, installation, testing & commissioning of SG iron body SinglePlate Wafer Type 1.00 No 959.50

NRV conf. to ASTMA 536, PN-1.6 complete with mating Flanges class # 150 with bolts

& nuts, washers, gaskets 3 mm thick, etc. with all complete. accessories (A) 50 mm dia.

170 Supply, installation, testing & commissioning of SG iron body SinglePlate Wafer Type 1.00 No 1060.50

NRV conf. to ASTMA 536, PN-1.6 complete with mating Flanges class # 150 with bolts

& nuts, washers, gaskets 3 mm thick, etc. with all complete. accessories (B) 80 mm dia.

171 Supply, installation, testing & commissioning of SG iron body SinglePlate Wafer Type 1.00 No 969.60

NRV conf. to ASTMA 536, PN-1.6 complete with mating Flanges class # 150 with bolts

& nuts, washers, gaskets 3 mm thick, etc. with all complete. accessories (C) 100 mm

172 Supply, installation, testing & commissioning of Y Type Strainer complete with mating 1.00 No 3716.80

flanges with bolts & nuts, washers, gaskets 3 mm thick, etc. with all complete

accessories. (A) 80 mm dia.

Item Rate In

Description of Item Quantity Unit Amount

No figures

173 Supply, installation, testing & commissioning of Y Type Strainer complete with mating 1.00 No 6514.50

flanges with bolts & nuts, washers, gaskets 3 mm thick, etc. with all complete

accessories. (B) 100 mm Dia

174 Supply, installing, testing and commissioning of Normax make CI heavy duty ball type 1.00 No 3535.00

foot valve with flanges, nut bolts, gaskets etc. with necessary complete accessories. (A)

80 mm dia.

175 Supply, installing, testing and commissioning of Normax make CI heavy duty ball type 1.00 No 4949.00

foot valve with flanges, nut bolts, gaskets etc. with necessary complete accessories. (B)

100 mm dia

176 Supply, installation, testing & commissioning of Four way fire brigade Inlet connection 1.00 No 6565.00

with 63 mm dia. stainless steel (SS304) instantaneous male inlets with built in non

return valve in each inlet with 150 mm dia. header pipe, suitable rubber cap and GI

chain including nuts, bolts, washers, gasket 3 mm thick, etc. with all complete.

177 Supply, installation, testing & commissioning of Two way fire brigade Inlet connection 1.00 No 4969.20

with 63 mm dia. stainless steel (SS304) instantaneous male inlets with built in non

return valve in each inlet with 100 mm dia. header pipe, suitable rubber cap and GI

chain including nuts, bolts, washers, gasket 3 mm thick, etc. with all complete.

178 Supplying FIRE bucket round bottom of 9 liters capacity made out of 24 gauge G.I Sheet 4.00 No 994.85

with extra handle at bottom duly painted white inside and Red out side with FIRE

mark. Filled with dry-sand and kept on existing stand provided or hung on wall hook.

179 Supplying and erecting floor mounting Stand for keeping four nos. of FIRE buckets 1.00 No 5383.30

comprising 1500 mm in length, 900 mm height frame made out of 30mm x 30 mm x

mm angle iron with cross supports legs, welded with 4 hooks and duly painted with

one coat of primer and two coats of approved enamel P O red paint.

180 Supply, installation, testing & commissioning of Oblique pattern type stainless steel (SS 8.00 No 3282.50

304) single headed External Fire Hydrant Valve with 63 mm dia. female instantaneous

outlet conf. to IS: 5290, type - A, including mating flanges, galvanised nuts, galvanised

bolts/studs, washers & gaskets 3 mm thick with all complete.

181 Supply, installation, testing & commissioning of 63 mm dia. stainless steel (SS 304) 8.00 No 1161.50

Universal Branch Pipe conf. to IS:

182 Supply & installation, testing & commissioing of Fire Fighting Hose - conf. to IS : 636, 8.00 No 3999.60

type A (type-1), The fire hose shall be 15 m long with 63 mm dia. stainless steel (SS

304) couplings conf. to IS: 903, at both the ends for connection with the hydrant valve

and the branch pipe.

183 Supply, installation, testing & commissioning of fabricated from 3 mm MS sheet, hose 8.00 No 1136.25

box of size-450 mm x 600 mm x 250 mm - painted with Fire Red as per IS: 5, shade no.

536 front 3 mm thick transparent glass with lock & key, handle and brass hinges - to

accommodate one number of 15 mtr long hose and one number of universal branch

pipe, including supporting arrangement with civil work.

Item Rate In

Description of Item Quantity Unit Amount

No figures

184 Supply, Installation, testing & commissioing of Swinging type mild steel hose reel drum 8.00 No 4848.00

with 20 mm dia. x 30 mtr. rubber hose as per IS: 884. The mounting stand shall be of

mild steel and the hose shall be fitted with a SS shut-off nozzle & SS ball valve of 25 mm

dia. including supporting arrangement with all complete. accessories

185 Excavation of foundation, Lead And Liftting of soil work and RCC work 4.00 Cum 1070.60

186 Filling Of Gaps Between pipe and Core Cutting Hole With Chemical and Cement 20.00 No 303.00

187 Supply, fabrication and erection of Structure MS Material as like Angle, C channel, I 150.00 Kg 80.80

188 Supply, installation and commissioning of Flexible cable for 1.5 sq mm x 3 core for 40.00 Mtr 70.70

pressure switch

189 Supply, installation and commissioning of Copper Armour cable for 10 HP Motor - 4 sq 15.00 Mtr 181.80

mm x 3 Core (Only Panel To Pump)

190 Supply, installation and commissioning of Copper Armour cable for 40 HP Motor - 10 22.00 Mtr 429.25

sq mm x 3 Core (Only Panel To Pump)

191 Supply, Filling and Fixing of approved make ABC type fire extinguisher - 6 Kg. Capacity 12.00 No 1111.00

as per IS:15683 & IS :

192 Supply, Filling and Fixing of approved make CO2 type fire extinguisher. Capacity 4.5 Kg. 12.00 No 3939.00

(conforming to IS-15683).

193 Submitting the application to obtain Fire NOC for three year to Fire Department 1.00 No 50500.00

194 Supply, Installation and commissioning of Air Release Valve, 25 mm Dia. connection. 2.00 No 1363.50

195 Supply, Installation and commissioning of Fire Alarm Panel Conventional type, 4 loops 2.00 No 24846.00

with complete accessories.

196 Supply, Installation and commissioning of Audio hooters with complete accessories. 6.00 No 1035.25

197 Supply, Installation and commissioning of Manual Call Points with complete 6.00 No 974.65

accessories.

198 Cable (Armour) for Fire Alarm system 250.00 Mtr 90.90

199 Core cutting in wall and in RCC slab with size as below: (A) 50 mm dia. hole 8.00 No 404.00

200 Core cutting in wall and in RCC slab with size as below: (B) 80 mm dia. hole 3.00 No 454.50

201 Core cutting in wall and in RCC slab with size as below: (C) 100 mm dia. hole 6.00 No 494.90

202 Core cutting in wall and in RCC slab with size as below: (D) 150 mm dia. hole 3.00 No 580.75

203 Core cutting in wall and in RCC slab with size as below: (E) 200 mm dia. hole 2.00 No 868.60

204 Supply, installation, testing & commissioning of ISI approved electrical motor operated 1.00 Set 134381.51

Kirloskar make fire hydrant main pump set horizontal end suction back pull out top

discharge centrifugal fire pump set with all the standard acessories, base frame,

coupling, and foundation bolts with following specifications Model -DB 50/26, Flow-54

m3/hr, Head-70 meter, Motor Rating -22KW/30HP/3 ph Suc x Del - 65 x

Item Rate In

Description of Item Quantity Unit Amount

No figures

205 Fire Hydrant Panel suitable for 10 hp Jockey pump, 30 hp (54 m3/hr @ 70 m head) 1.00 No 82597.80

main electrical pump and 40 hp (97 m3/hr @ 70 m head) Diesel engine operated pump

A) Incomer MCCB - 1 Nos R Y B Indication - 1 Set VAF Digital Meter - 1 Set B) Outgoing

F1 60 HP Star Delta Starter - 1 For Main pump F2 10 HP DOL Starter - 1 For Jockey

Pump F3 Auto - On / Off Diesel Pump With Battery Charger Control Circuit With Auto -

Manual On/Off On/Off Trip Indication On/Off Push Button C) Fabrication Dully Powder

Coated PO Red Colour, Fabricated From 14/16 SWG,GI Sheet , IP-42 Protection,-Fixed

Type Floor Mounted Cable Entry : Bottom

206 Fire Plan Approval 1.00 No 39390.00

207 Legal Fees 3650.00 Sqm 9.09

208 Demolition of all types of Dismantling materials from the site. Given to credit of 1.00 Job 253800.00

dismantling material if necessity of applicable. RCC work, Flooring Tiles, Brick, Doors

window, Plumbing etc as per directed engineer incharge.

209 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) 313.00 Pt. 485.81

both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up

to 10 mtr length , in below type of pipe erected with 6A Modular type switch / bell

push & accessories and earth continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe

erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.(f) with

medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete Cat.III

210 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of 74.00 Pt. 674.68

.ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected with 6A Modular type switch and hum free EME

step type electronic fan regulator mounted and accessories with earth continuity of

following type erected on PVC / Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed. (f)

with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete Cat.III

211 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket 57.00 Pt. 257.55

erected on PVC / Metallic/Wooden box, single mounting base frame covered with

textured / metallic/white front plate modules erected on / in wall / ceiling with

following type accessories Cat.III

212 Providing following type of Modular Type Accessories mounted with PVC / 32.00 Ea. 151.50

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections as per site

situation directed by Engineer In charge. (1)One No. SP 6 Amp. Cat.III

Item Rate In

Description of Item Quantity Unit Amount

No figures

213 Providing following type of Modular Type Accessories mounted with PVC / 32.00 Ea. 151.50

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections as per site

situation directed by Engineer In charge. (2) One No 5 pin plug Cat.III

214 Providing following type of Modular Type Accessories mounted with PVC / 69.00 Ea. 25.25

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections as per site

situation directed by Engineer In charge. (7) Blank Plate Single Cat.III

215 Providing following type of Modular Type Accessories mounted with PVC / 35.00 Ea. 160.59

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections as per site

situation directed by Engineer In charge. (8) Computer RJ-45 socket Cat.III

216 Providing following type of Modular Type Accessories mounted with PVC / 40.00 Ea. 180.79

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections as per site

situation directed by Engineer In charge. (9) 16 Amp. SP one way switch Cat.III

217 Providing following type of Modular Type Accessories mounted with PVC / 77.00 Ea. 199.98

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections as per site

situation directed by Engineer In charge. (10) 6/16Amp. Universal socket Cat.III

218 Providing following type of Modular Type Accessories mounted with PVC / 37.00 Ea. 410.06

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections as per site

situation directed by Engineer In charge. (14) 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double

Pole Modular MCB Switch Cat.III

219 Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size 840.00 Mtr. 33.33

complete to be erected on/in wall or ceiling erected with necessary PVC fittings &

Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in

approved manner as directed (b) 25 mm

220 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked 2880.00 Mtr. 82.82

stranded Copper conductor wire in following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of following size (A) With medium

class Rigid PVC pipe and accessories (b) 2 wire 2.5 sq. mm

221 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked 888.00 Mtr. 112.11

stranded Copper conductor wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) with medium class Rigid PVC pipe and

accessories (a) 2 wire 4 sq. mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

222 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked 250.00 Mtr. 260.58

stranded Copper conductor wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) with medium class Rigid PVC pipe and

accessories (h) 4 wire 6 sq. mm

223 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, 110.00 Mtr. 56.56

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required. (e) One wire 6.00 sq. mm

224 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, 32.00 Mtr. 91.91

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required. (f) One wire 10.00 sq. mm

225 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, 30.00 Mtr. 142.41

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required. (g) One wire 16.00 sq. mm

226 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, 10.00 Mtr. 236.34

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required. (h) One wire 25.00 sq. mm

227 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI 130.00 Mtr. 46.46

marked copper wires of following size to be erected as directed. (e) 1.50 Sq.mm 3 core

round PVC sheathed

228 Supplying & erecting approved make LAN cable of following size in existing pipe as per 910.00 Mtr. 47.47

direction [C] CAT -

229 Providing & erecting Switch board for Computer or electric apparatus consisting of 35.00 Ea. 1133.22

following modular type accessories mounted with PVC / Metallic concealed/open box

with single mounting base frame covered with textured/metallic /white front

plate,modules erected with necessary connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat.III

230 Decorative call bell Ting-tong box type 250 volts complete erected 2.00 Ea. 71.71

Item Rate In

Description of Item Quantity Unit Amount

No figures

231 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt 113.00 Ea. 535.30

assembled on single MCPCB, with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/ aluminium die cast powder coated and high

U.V. & corrosion resistance with diffuser with company mark/name 160V to 270V,

Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown

wattage capacity between the ranges shown.) (A) Tube Light with integral driver (v)

36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet Cat.III

232 Supplying and erecting led lamps with following wattage capacity of 220 to 240 34.00 Ea. 112.11

voltage, minimum 15000 burning hours life, 500 V in built-surge

protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp

holders, pf >= 0.5 (A) LED Lamps integral type, with PC diffuser suitable LAMP holder

(ii) 5 to 8 watts Cat.III

233 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt 127.00 Ea. 1794.77

assembled on single MCPCB, with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/aluminium pressure die cast powder coated

and high U.V. & corrosion resistance with diffuser housed in aluminium casted body

with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown

wattage capacity between the ranges shown.) (B) LED Panel Light with provision for

Plane front frame with translucent cover fixed to housing complete.IP20 (vi) 36 watts,

24" x 24", Surge- 2KV Cat.III

234 Supplying and erecting LED street light / Flood light fittings with High power White 22.00 Ea. 5976.17

LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency more than

130 lm/w and corrosion free High pressure die cast aluminum housing with smooth

finish powder coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company mark/name

engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT

3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED fittings.The Engineer

(IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with

over-voltage protection. (iii) Above 60 to 90 watts Cat.III

Item Rate In

Description of Item Quantity Unit Amount

No figures

235 Supplying and erecting LED street light / Flood light fittings with High power White 2.00 Ea. 4092.52

LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency more than

130 lm/w and corrosion free High pressure die cast aluminum housing with smooth

finish powder coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company mark/name

engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT

3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED fittings.The Engineer

Lantern LED fitting comprises of finish cast aluminum spigot and spun aluminum

canopy fixed with opal polycarbonate, pipe arrangement for vertical mounting driver

and accessories wired upto terminal block.IP 65 (i)20- 30W Cat.III

236 Providing and erecting Approved make Four pole moulded case circuit breaker having 4.00 Ea. 6173.12

breaking capacity ICU of 25 KA. at 415 V,having normal current rating up to 25 A to

100A. with Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s.

with all internal connections, spreader tinned copper & complete erected in existing

G.M.S. housing. ICS=100% of ICU only Cat III

237 Providing and erecting Approved make Four pole moulded case circuit breaker having 3.00 Ea. 8055.76

breaking capacity ICU of 35 KA. at 415 V. having normal current rating 125A. with

Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all

internal connections, spreader tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III

238 Providing and erecting Approved make Four pole moulded case circuit breaker having 1.00 Ea. 16221.61

breaking capacity ICU of 35 KA. at 415 V. having Normal current rating 200A.with

variable Thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all

internal connections, spreader tinned copper & complete erected in existing

G.M.S.housing ICS=100% of ICU only Cat III

239 Providing and erecting Approved make Earth fault Relay suitable to mount with inter 1.00 Ea. 4983.34

connection suitable to following size of moulded case circuit breaker having CT ratio

& MCCB rating as following along with shunt trip 220V AC. with all internal

connections & complete erected in existing M.S.housing. (2) 125 A -200 A , CT Ratio

240 Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper 1.45 Rn.Mtr 1961.42

Busbars with four equal Nos. of electrolyte bus having current density not more than

1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour

insulating tape for phase sequence of following current carrying capacity, erected with

necessary bus bar supports /insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections. (A) Suitable for 100 Amp. Capacity

Item Rate In

Description of Item Quantity Unit Amount

No figures

241 Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper 1.00 Rn.Mtr 3202.71

Busbars with four equal Nos. of electrolyte bus having current density not more than

1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour

insulating tape for phase sequence of following current carrying capacity, erected with

necessary bus bar supports /insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections. (B) Suitable for 200 Amp. capacity

242 providing and erecting Miniature circuit breaker single pole 0.5A to 2A system and 24.00 Ea. 270.68

having breaking capacity 10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat.III

243 providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to 120.00 Ea. 112.11

operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with ISI Mark Cat.III

244 Providing & erecting 240 V MCB double pole switch for motor & inductive load (C 6.00 Ea. 330.27

Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having

following capacity (B) 40 Amp. Cat.III

245 Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 4.00 Ea. 278.76

10 KA breaking capacity & confirms to IS : 8828 in existing box having following

capacity (A) 6 to 32 Amp. Cat.III

246 Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) having 16.00 Ea. 578.73

10KA breaking capacity & confirms to IS :8828 in existing box having following

capacity (a) 6 to 32 Amp. Cat.III

247 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) 8.00 Ea. 595.90

having 10KA breaking capacity & confirms to IS :8828 in existing box having following

capacity (a) 6 to 32 Amp. Cat.III

248 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) 1.00 Ea. 737.30

having 10KA breaking capacity & confirms to IS :8828 in existing box having following

capacity (c)63 Amp. Cat.III

249 Sheets steel powder coated enclosure suitable for incorporating One/Two nos. MCB. 4.00 Ea. 176.75

250 Providing and erecting Sheet Steel powder coated MCB distribution board - flush / 10.00 Ea. 2339.16

surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used) suitable for (B) three phase

incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b)

sheet steel double door (i)4 way

251 providing and erecting Approved make RCCBs conforming to IS: 12640 and having 30.00 Ea. 1969.50

sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having characteristic of quick action & tripping

with all advance feature & do not incorporate any electronic component. for following

Max. rating erected as directed (i) 25 Amps.DP Cat.III

Item Rate In

Description of Item Quantity Unit Amount

No figures

252 providing and erecting Approved make RCCBs conforming to IS: 12640 and having 4.00 Ea. 2235.13

sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having characteristic of quick action & tripping

with all advance feature & do not incorporate any electronic component. for following

Max. rating erected as directed (ii) 40Amps. DP Cat.III

253 Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG. 36.00 Kg 77.77

254 Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. dia. 8.00 Ea. 368.65

galvanised iron pipe with coupling and buch buried in specially prepared earth pit

complete with necessary 8 SWG earth wire.

255 For using salt and charcoal / coke as required for pipe type earthing. 11.00 Ea. 171.70

256 Supplying & erecting in earthpit of minimum bore dia. 225mm size approved make 4.00 Ea. 5842.85

Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made

of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 80 mm having 80-200

Micron galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising,

connection terminal dia of 14 mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for following type of

applications with chamber and heavy duty cover (A)(approved make OEM has to

submit test certificate including value of earth resistance of installation duly stamped

and signed by agency and officer Incharge has to ensure the value of earthing resistane

mentioned in test Certificate) & having back filling compound of (B) Inner chemical

(CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to retain moisture for long time

Necessary test report must be submitted by Agency. [A] For electrical installation up to

Length of Pipe - 1 Mtr

Back filling compound - 1 Nos. of Bag of 15 Kgs.

Item Rate In

Description of Item Quantity Unit Amount

No figures

257 Providing & erecting weather proof, dust & vermin Providing & erecting weather proof, 3.00 Sq.Mtr 14902.55

dust & vermin proof, floor mounted front operated indoor type cubical panel board

necessary IP-42 and above protection as per approval from engineer incharge made

from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet

for internal partitions with necessary accesories , supporting angles/ flats channel

including cutting, bending, drilling, welding, riveting with internal partitions & cable

alley as per requirements & instruction of engineer-in-charge with erection of supplied

switch gears, BUSBARS, suitable size of inter connecting PVC copper wire / copper-

aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for measuring

instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient

nos. of hinged doors, handles with locking arrangement and rubber gasket,heavy duty

end terminal connection,danger notice board,necessary ventilation,earthing strip

complete. The Panel shall be painted with epoxy powder coating. (The rates excludes

the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips,

meters, Fuses etc. The dimension shall be measured excluding base beams) The panel

shall be supplied with following approved manufacturers with following size. (B) The

standard companies switch gear shall be used and only manufacturers at CPRI

approved factory (i) with 350 mm depth

258 Providing , erecting , fabricating the M.S. structure as per requirement on site 47.00 Kg. 77.77

incorporating proper size of M.S. angles,square,round, flats, bars, channels, sections

complete with cutting, welding, grinding & finishing duly painted with one coat of red

oxide with erection on site as per direction of engineer in charge with necessary

grouting, cementing, plastering & finishing complete.

259 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand 125.00 Mtr. 284.82

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2

260 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand 20.00 Mtr. 378.75

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm

261 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand 155.00 Mtr. 540.35

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (F) 3 1/2 core 120 Sq. mm ( 70 Sq.

mm 1/2 core)

262 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid 529.00 Mtr. 126.25

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (B) 4 core 6 Sq. mm

263 Making trench in soft soil of suitable width of 90 cm deep for laying cable or locating 319.00 Mtr. 55.55

the fault all over the run and back filling the same and making the surface as normal

264 Supplying following size of Light duty “A” Class G.I . Pipe & erecting as directed by 55.00 Mtr. 300.98

Engineer-in-charge. (B) 50 mm dia

Item Rate In

Description of Item Quantity Unit Amount

No figures

265 Supplying following size of Light duty “A” Class G.I . Pipe & erecting as directed by 35.00 Mtr. 471.67

Engineer-in-charge. (C) 80 mm dia.

266 Providing & laying approved make Double walled corrugated pipes (DWC) of 264.00 Mtr. 62.62

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of

same material at required depth in existing trench for laying of cable. below ground /

road surface for enclosing cable (A)50 mm outer dia

267 Providing & laying approved make Double walled corrugated pipes (DWC) of 105.00 Mtr. 95.95

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of

same material at required depth in existing trench for laying of cable. below ground /

road surface for enclosing cable (C))90 mm outer dia

268 Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC 48.00 Ea. 38.38

insulated armoured cable complete with out going tails, insulating tape etc for

following size of cables.(B) 2 to 4 core 6 Sq. mm

269 Providing and, fixing heavy duty flange type brass double compression type cable 4.00 Ea. 75.75

gland with rubber ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (B) 3 & 1/2 core 35/50 Sq. mm

270 Providing and, fixing heavy duty flange type brass double compression type cable 4.00 Ea. 103.02

gland with rubber ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (C) 3 & 1/2 core 70 Sq. mm

271 Providing and, fixing heavy duty flange type brass double compression type cable 2.00 Ea. 140.39

gland with rubber ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (E) 3 & 1/2 core 120 Sq. mm

272 Solder less crimping type Aluminium lugs conforming to IS suitable for cable of 192.00 Ea. 6.06

following size evenly crimped with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an approved manner. (A) 1.5/

273 Solder less crimping type Aluminium lugs conforming to IS suitable for cable of 8.00 Ea. 20.20

following size evenly crimped with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an approved manner. (D) 35/50

274 Solder less crimping type Aluminium lugs conforming to IS suitable for cable of 16.00 Ea. 25.25

following size evenly crimped with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an approved manner. (E) 70 Sq.mm.

275 Solder less crimping type Aluminium lugs conforming to IS suitable for cable of 8.00 Ea. 45.45

following size evenly crimped with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an approved manner. (G) 120 Sq.mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

276 Supply, Installation, Testing and Commissioning of suitable sweep, BEE 5 Star rated, 74.00 Ea. 2629.03

Ceiling fan with Brush Less Direct Current (BLDC) permanent ferrite magnet Motor,

class of insulation: B, Rust free 3 nos.Aluminium blades, 2 nos. canopies, shackle kit

with earthing provision, copper winding, Power factor not < 0.9, Service Value

(CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM,230v (tolerance

as per IS : 374-2019), THD < 10%, compitible with electronic regulator unit for Speed

Control and all remaining accessories including safety pin, nut bolts, washers,

temperature rise = 75 degree C (Max.), suitable for 140 to 285 Voltage and rectifier

circuit with surge, over current and overload protection , 50 Hz, Single phase AC

Supply, earthing etc. Complete as required.[ Make shall be approved by Engineer in

Charge] (A) 1200 mm Sweep (48")

277 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod 74.00 Mtr. 108.07

erected duly painted for fan complete with proper insulation without leakage and

278 Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars 74.00 Ea. 108.07

up to 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty

PVC box complete erected concealed in Ceiling with necessary finishing.

279 Supplying & erecting approved make low noise decorative exhaust fan having square 35.00 Ea. 1366.53

frame ABS body with inbuilt lowers & square frame. 250mm with 1350 RPM Cat.II

280 Supplying and erecting approved make Octagonal pole made from HR sheet steel. The 13.00 Ea. 8192.11

pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS

2629/2633/4759, suitable suspend local wind speed with integral Junction box consist

of terminal plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for

MCB Mounting, stud type terminal and arrangement for cable termination to be

erected With Suitable foundation (Included) as per details given by manufacturer

considering site requirement. (D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm

thickness with 200mmX200mmX12mm base plate, 4-M20 Bolts and 600mm long with

necessary G.I. J Bolts .Approx Pole weight 59 kg

281 Supplying & erecting approved make SMC press moulded composite FRP. loop-in, 11.00 Ea. 515.10

loop-out approx. 2mm thick box complete with Bakelite connector strip

5way(3P+N+E),DIN rail for mounting mob & hinged doors as per requirement having

locking arrangements with mounting clamp with nuts, bolts & washers suitable for

erection on pole with cable clamps& earth bolt of following size of box. (B) 250mm x

200mm x 100mm [deep]

282 Supplying and erecting Street light pole bracket comprising main B Class GI pipe of 4.2 13.00 Ea. 491.87

cm/require outside dia. complete with suitable B Class G.I. sleeve tubing of approx.

45cms.length and suitable for 76.5mm/80mm/require size of pole top having nuts and

bolts for fixing the brackets and having spread of 0.5 mtr. Length with 110 deg.with

vertical plane and suitable welded stiffener reducer and nipple with check nut

complete painted with one coat.of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms. [A] Single Arm bracket 0.5 Mtr

283 Supplying and erecting B class Galvanized iron pipe having smooth finished bore of the 9.00 Ea. 215.13

pipe on both ends erected nuts and bolts along the pole / wall shaping the pipe as per

site requirement. Pipe dia as following. (B) 32 mm dia

Item Rate In

Description of Item Quantity Unit Amount

No figures

284 Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 4.00 Ea. 55893.40

150 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of the water should

drop by 15˚C within a hour, The water cooler should be comprising of hermetically

sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating,

coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body

of water cooler will be made from Stainless Steel.

285 Supplying & erecting 5 stage single reverse osmosis water purification system with 4.00 Ea. 29187.99

M.S. powder coated frame, prefilter housing with 'O' ring presediment filter GAC filter,

carbon filter suitable buster DC pump capacity 80 psi, mention with 40 psi inline type

post carbon filter auto low & high pressure switches with following size of storage tank

& LPH capacity & erected as directed [C] 50 Ltr / Hr with 150 psi 2 nos booster pump

286 Supplying and erecting horizontal / vertical mounting type storage water heater with 4.00 Ea. 15195.45

copper container housed in M.S./S.S./ABS body insulated with glass wool/puff

complete with heating elements,adjustable thermostats 300C to 850C, indicating lamp,

safety valve, fusible plug, etc.complete erected with coach bolts, nuts. washers &

cementation (E)50 Ltr. with 2 KW. heating element Premium Category

287 Supplying, installing, testing & commissioning of SOLAR WATER heating system as per 1.00 Ea. 102530.15

prevailing IS code comprising of Solar flat locket collector, stainless steel hot water

storage isolated tank with S.S. heat exchanger, absorber made of copper sheet & copper

tube of following capacity in liter / day (LPD) with "B" size aluminium box collector

with appropriate capacity electrical backup arrangement (Excluding inlet & outlet pipe

lines) (D) Capacity of 500 LPD

288 Supplying and erecting approved make panel mounting type Digital Voltmeter having 1.00 Ea. 1275.63

3 digits LED display, 0 to 750 AC Volts range erected on existing panel board with all

connection, wiring etc .with manufacturers calibration certificate.

289 Supplying and erecting approved make panel mounting type Digital Ammeter having 3 1.00 Ea. 1558.43

digits LED display, external CT operated, calibrated for 0 to 1000 Amps suitable to

operate on 500 Volt AC , erected on existing panel board with all connection, wiring

etc .with manufacturers calibration certificate.

500 V on existing panel board with necessary connections.

291 Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio 3.00 Ea. 274.72

15 VA burden erected in existing CRCA box duly secured with insulating materials

connected to the meter

292 Supplying and erecting approved make suitable panel indicator LED type lamp, lens 6.00 Ea. 43.43

cover, complete erected with necessary connections.

Item Rate In

Description of Item Quantity Unit Amount

No figures

293 SITC of Vertical Air Termination Solid aluminium with Base- 10 mm dia and 1000 mm 8.00 Ea. 9416.23

long. Air Termination Base tested for conditioning, Ageing Test & Lightning impulse

current withstand test: 100 kA of 10/350µs waveform in an accredited Third party

laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol with MAST 34mm dia

mm long- Cold Galvanized

294 SITC of 8 mm dia solid Aluminium Conductor for roof top mesh grid and tested as per 267.05 Mtr. 299.97

IEC 62561- 2 conducted in the Govt. accredited thirty party laboratory to meet the

requirement of IS/IEC 62305 with Required Accessories - Aluminium Holding clamp at

every 1 mtr distance, Aluminium/SS cross splicer at every crossing of Alu. conductor,

Expansion piece with connectors at every 20 mtr distance, Aluminium straight Splicer

to connect conductors. All Accessories should be tested as per IEC 62561-1 2018 Cl.

6.3 for conditioning & Ageing Test & 6.4 for Lightning impulse current withstand test:

100 kA of 10/350µs waveform(Ageing & Electrical test ) conducted in a sequence

manner & tested in the Govt. accredited Third party laboratory to meet the

requirements of IS/IEC

295 SITC of Galvanized Steel Flat 25x6 mm thickness from earth electrode directly in 144.00 Mtr. 154.53

ground as required. Zinc coating: 500 g/m square (Approx:70 micron coating) tested

and used exclusively for lightning protection earthing system and ring equipotential

296 SITC of 14.2 mm dia 3 mtr long Earth electrode of High tensile steel electrode with 250 8.00 Per Set 5992.33

micron copper bonding & 1 bag of Carbon fill Based environment friendly backfill

tested as per IEC 62561-7 in NABL accredited Laboratory and suitable stainless Steel

double sided clamp. Eco Friendly rust proof heavy duty weather proof Polyethylene

Earth Pit Chamber with following dimensions :254 mm dia (top), 330 mm dia (bottom)

& 260 mm (height).

297 Supplying and erecting, commissioning and testing of Diesel Generating set confirming 1.00 Ea. 1029194.04

to IS: 4722:1968 & BS:5514 having continuous rating, 3 phase, 415 volts, 50 cycles A.C.

supply comprising of a totally enclosed air/water cooled diesel engine with multi-

cylinders developing suitable BHP not less than following capacity at 1500 RPM with

10% overload for one hour in 24 hours with standard accessories like fly wheel,

lubricating oil cooler, "A" class governor, heavy duty fuel wheel and lubricating oil

filter, oil bath air filler, lubricating oil pressure gauge, end exhaust manifold, standard

set of tools with adjustable spanners, screw drivers, cylinder head to cover, joint

cylinder head to exhaust, element lube oil filter, 12 / 24 volts electric starting

equipment complete with standard heavy duty battery, dynamo, cut-outs, ammeter,

necessary wiring, pressure gauge, starter etc and heavy duty Residential type exhaust

silencer (With DEF System) and vertical hot air duct both

logged with asbestos rope, save oil trays, exhaust piping of required length, standard

wall/floor mounted fuel with level indicator and piping and drip proof alternator, self

excited, self regulated, screen protected, with excitation system, capable of delivering

the rated system output at 415 volts, 3 phase, 0.8 PF, 50 Hz, 4 wire, running at

RPM, conforming to IS-4722- 1968 with voltage regulation +/- 5% of rated voltage

from no load to full load. Both the engine and alternator fitted on a common fabricated

steel base plate with antivibration mounting engine and alternator both connected

to each other by flexible flange coupling and with floor/wall mounted control panel

adequate capacity,

Item Rate In

Description of Item Quantity Unit Amount

No figures

indicator lamps duly wired with HRC fuses. The alternator & control panel shall be

connected with provided suitable capacity armoured cable and complete with Acoustic

enclosure (canopy) made out of 16 SWG CRCA Sheet, sound absorbing material

Rockwool of 64 density & 100 mm thick conforming to IS:8183 / PU Foam of

Density - at least 40 mm. The resin bonded rockwool covered from inside the canopy

by perforated sheet with 3/4 mm holes, sound level not more than 75 dB at a distance

of 1 mtr, as per PVCT norms.DG set should have in built fuel tank capacity of minimum

8 hrs of continous running capacity on full load . Erection, commissioning and

satisfactory testing as per requirement with first filling of fuel (minimum up to the

80% of fuel tank capacity), oil, etc. with guarantee / Warrantee of complete system for

Two years. & with obtaining all necessary certificate from Electrical Inspector. The

Capacity and Ratings of DG sets are as below. (As per new CPCB4+ Emission norms

Engine With - Turbo Charger, EGR (Exhaust Gas Recirculation), CRS (Common Rail Fuel

Integrated wiring harness connected to ECU .) (M) Continuous rating of 125 KVA ,BHP

not less than 154 BHP

298 Providing & erecting approved make AMF control panel suitable for following size of 3 1.00 Nos 121201.01

phase, 415 V., 50 cycles, A.C. diesel generating set complete of scope as detailed below:

1) Power module: A pair of electromechanically interlocked contactors (for mains &

generator) Overload relay for generator contactor Neutral contactor for mains and

generator Power socket for connections.

2) Control and metering module: Line voltage monitor. Generator voltage monitor

Ammeter 3 items attempt start facility. Air circuit breakers/MCB/MCCB of suitable

rating for auto/manual operation. Auto/manual switch. Emergency stop push buttons.

Manual start push button. frequency meter. Engine hour meter. Two earthing studs.3)

Protection module: The engine shutdown in the unlikely event of Low lube oil pressure

High cylinder head temperature. V belt failure.

4) Indicators with alarm Load on generator.

5) Indicators Load on mains Engine fails to start . Emergency stop battery charger.

The AMF Panel of following capacity(C) AMF Control Panel for100 KVA/125 KVA3

phase DG Set

299 Providing and erecting Inverter based approved make split air-conditioning unit 4.00 Ea. 51666.55

consisting of condensing unit with variable speed fan motor, inverter type hermetically

sealed rotary compressor with accessories etc. duly connected separately erected

evaporating unit and blower motor with its accessories by means of extra supplied

proper insulated copper tubing,drain PVC pipes suitable for ( cost includes Eco

Friendly green gas charging and 15A plug top & Remote Control & MS Stand) with

necessary core cutting(1)For ISEER Range (KWH/KWH)(3.1 to 3.99)(C) for 1.7 to

ton capacity[8-3-2]

300 Supplying and erecting insulated pair of soft copper tubing open or concealed 10.00 Rmt 965.56

including power and control cable,necessary PVC drain pipes for Split AC machine up

to 4 TR capacity

Total Rs.

Rs. Six crore fifty lakh twenty four thousand seven hundred forty seven and ninety five paisa only.

Note:- The Credit Value of Dismentalled Materials of Amount Rs. 454600.00 shall be recovered from the 1st

Running Bill of the Contractor.

Item Rate In

Description of Item Quantity Unit Amount

No figures

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and words) of the estimated rate

mentioned above. Amount of my /our

Tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

1 The Credit Value of Dismentalled Materials of Amount Rs. 454600.00 shall be recovered from the 1st Running Bill of the Contractor.

The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which no extra

1 payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement Consumption/16/C

Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix design the cost of difference of cement

consumption have been deducted from the rate of original item at the rate of input rate mentioned in all the tender.

Executive Engineer

Tapi ( R & B ) Division